Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3008 device /dev/ttyimx6q-sabresd-2 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03 (Jan 20 2018 - 10:43:25 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 27C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial flash target is MMC:1 Net: Warning: ethernet@02188000 using MAC address from ROM eth0: ethernet@02188000 [PRIME] Fastboot: Normal Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.205 (1304 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x12000000 1018545/tftp-deploy-kjnnacrk/kernel/zImage tftp 0x12000000 1018545/tftp-deploy-kjnnacrk/kernel/zImage Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1018545/tftp-deploy-kjnnacrk/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 9.9 MiB/s done Bytes transferred = 9662976 (937200 hex) => tftp 0x12C00000 1018545/tftp-deploy-kjnnacrk/ramdisk/ramdisk.cpio.gz.uboot tftp 0x12C00000 1018545/tftp-deploy-kjnnacrk/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1018545/tftp-deploy-kjnnacrk/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x12c00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 11 MiB/s done Bytes transferred = 16056172 (f4ff6c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 1018545/tftp-deploy-kjnnacrk/dtb/imx6q-sabresd.dtb tftp 0x18000000 1018545/tftp-deploy-kjnnacrk/dtb/imx6q-sabresd.dtb Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1018545/tftp-deploy-kjnnacrk/dtb/imx6q-sabresd.dtb'. Load address: 0x18000000 Loading: *### 5.2 MiB/s done Bytes transferred = 43473 (a9d1 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x12000000 0x12C00000 0x18000000 bootz 0x12000000 0x12C00000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0x937200 ] ## Loading init Ramdisk from Legacy Image at 12c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16056108 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800d9d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.129-cip12 (KernelCI@build-j399661-arm-gcc-10-multi-v7-defconfig-lnr76) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jul 26 02:08:36 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Smart Device Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933708K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49332K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022457] Console: colour dummy device 80x30 <6>[ 0.024347] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034759] pid_max: default: 32768 minimum: 301 <6>[ 0.039800] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047211] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055851] CPU: Testing write buffer coherency: ok <6>[ 0.060327] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065889] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072240] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080023] rcu: Hierarchical SRCU implementation. <6>[ 0.087063] EFI services will not be available. <6>[ 0.089294] smp: Bringing up secondary CPUs ... <6>[ 0.094574] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094583] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105969] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105977] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117135] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117144] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127586] smp: Brought up 1 node, 4 CPUs <6>[ 0.131807] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138266] CPU: All CPU(s) started in SVC mode. <6>[ 0.143690] devtmpfs: initialized <6>[ 0.154352] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159689] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169562] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179800] pinctrl core: initialized pinctrl subsystem <6>[ 0.184214] DMI not present or invalid. <6>[ 0.187352] NET: Registered protocol family 16 <6>[ 0.194252] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200899] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201092] cpuidle: using governor menu <6>[ 0.209163] CPU identified as i.MX6QP, silicon rev 1.0 <6>[ 0.385735] vdd3p0: supplied by regulator-dummy <6>[ 0.781086] No ATAGs? <6>[ 0.781267] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.789048] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.799040] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.809185] Serial: AMBA PL011 UART driver <6>[ 0.840223] mxs-dma 110000.dma-apbh: initialized <6>[ 0.848623] iommu: Default domain type: Translated <6>[ 0.851346] vgaarb: loaded <5>[ 0.854715] SCSI subsystem initialized <6>[ 0.858449] usbcore: registered new interface driver usbfs <6>[ 0.863653] usbcore: registered new interface driver hub <6>[ 0.869237] usbcore: registered new device driver usb <6>[ 0.880904] i2c i2c-0: IMX I2C adapter registered <6>[ 0.891966] i2c i2c-1: IMX I2C adapter registered <6>[ 0.895725] i2c i2c-2: IMX I2C adapter registered <6>[ 0.900422] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.904257] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.913692] PTP clock support registered <6>[ 0.921299] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.972754] NET: Registered protocol family 2 <6>[ 1.974872] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.983333] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.990819] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.998895] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.006339] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.013001] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.019704] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.027177] NET: Registered protocol family 1 <6>[ 2.032266] RPC: Registered named UNIX socket transport module. <6>[ 2.037770] RPC: Registered udp transport module. <6>[ 2.042769] RPC: Registered tcp transport module. <6>[ 2.047687] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.054415] PCI: CLS 0 bytes, default 64 <6>[ 2.059051] Trying to unpack rootfs image as initramfs... <6>[ 3.392502] Freeing initrd memory: 15680K <4>[ 3.394390] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.401632] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.411447] Initialise system trusted keyrings <6>[ 3.414640] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.426939] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.430885] NFS: Registering the id_resolver key type <5>[ 3.435579] Key type id_resolver registered <5>[ 3.439926] Key type id_legacy registered <6>[ 3.444344] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.451149] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.458850] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.463891] Key type asymmetric registered <5>[ 3.467766] Asymmetric key parser 'x509' registered <6>[ 3.472967] bounce: pool size: 64 pages <6>[ 3.477019] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.484664] io scheduler mq-deadline registered <6>[ 3.489429] io scheduler kyber registered <4>[ 3.517718] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 3.548406] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.555354] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.605724] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.613772] SuperH (H)SCI(F) driver initialized <6>[ 3.616659] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.624646] printk: console [ttymxc0] enabled <6>[ 3.624646] printk: console [ttymxc0] enabled <6>[ 3.633817] printk: bootconsole [ec_imx21] disabled <6>[ 3.633817] printk: bootconsole [ec_imx21] disabled <6>[ 3.645611] msm_serial: driver initialized <6>[ 3.651531] STMicroelectronics ASC driver initialized <6>[ 3.658695] STM32 USART driver initialized <4>[ 3.673423] panel-simple panel: supply power not found, using dummy regulator <6>[ 3.689620] brd: module loaded <6>[ 3.702174] loop: module loaded <6>[ 3.709440] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.717689] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.725985] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.734450] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.742448] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.750169] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.757735] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.768311] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.775600] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.784692] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.795386] scsi host0: ahci-imx <6>[ 3.799233] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 82 <6>[ 3.819164] CAN device driver interface <6>[ 3.824516] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.831911] pps pps0: new PPS source ptp0 <6>[ 3.887458] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.894979] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.900212] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.906480] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.912163] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.923701] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.931425] usbcore: registered new interface driver pegasus <6>[ 3.937391] usbcore: registered new interface driver asix <6>[ 3.943107] usbcore: registered new interface driver ax88179_178a <6>[ 3.949502] usbcore: registered new interface driver cdc_ether <6>[ 3.955661] usbcore: registered new interface driver smsc75xx <6>[ 3.961732] usbcore: registered new interface driver smsc95xx <6>[ 3.967774] usbcore: registered new interface driver net1080 <6>[ 3.973748] usbcore: registered new interface driver cdc_subset <6>[ 3.979962] usbcore: registered new interface driver zaurus <6>[ 3.985892] usbcore: registered new interface driver cdc_ncm <6>[ 3.995157] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.001980] ehci-pci: EHCI PCI platform driver <6>[ 4.006730] ehci-platform: EHCI generic platform driver <6>[ 4.012535] ehci-orion: EHCI orion driver <6>[ 4.017019] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.021502] ehci-st: EHCI STMicroelectronics driver <6>[ 4.026819] ehci-exynos: EHCI Exynos driver <6>[ 4.031458] ehci-atmel: EHCI Atmel driver <6>[ 4.035899] tegra-ehci: Tegra EHCI driver <6>[ 4.040370] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.046853] ohci-pci: OHCI PCI platform driver <6>[ 4.051621] ohci-platform: OHCI generic platform driver <6>[ 4.057354] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.061827] ohci-st: OHCI STMicroelectronics driver <6>[ 4.067141] ohci-atmel: OHCI Atmel driver <6>[ 4.072444] usbcore: registered new interface driver usb-storage <6>[ 4.086471] i2c /dev entries driver <6>[ 4.109578] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.116062] sdhci: Copyright(c) Pierre Ossman <6>[ 4.123293] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.131426] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.138709] sdhci-esdhc-imx 2194000.mmc: Got CD GPIO <6>[ 4.138959] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.144025] sdhci-esdhc-imx 2194000.mmc: Got WP GPIO <6>[ 4.149261] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.154597] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.165435] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.171994] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.174787] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.186819] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.191559] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.192287] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <6>[ 4.194196] usbcore: registered new interface driver usbhid <6>[ 4.213236] usbhid: USB HID core driver <4>[ 4.221470] isl29018 2-0044: No cache defaults, reading back from HW <3>[ 4.228766] isl29018 2-0044: Failed to read 1: -6 <3>[ 4.233776] isl29018 2-0044: regmap initialization fails: -6 <6>[ 4.238379] mmc2: new high speed SDHC card at address aaaa <6>[ 4.242772] NET: Registered protocol family 10 <6>[ 4.251549] mmcblk2: mmc2:aaaa SS08G 7.40 GiB <6>[ 4.251802] Segment Routing with IPv6 <6>[ 4.260270] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.267223] NET: Registered protocol family 17 <6>[ 4.271975] can: controller area network core <6>[ 4.276671] NET: Registered protocol family 29 <6>[ 4.281396] can: raw protocol <6>[ 4.284632] can: broadcast manager protocol <6>[ 4.289088] can: netlink gateway - max_hops=1 <5>[ 4.294188] Key type dns_resolver registered <6>[ 4.299870] ThumbEE CPU extension supported. <5>[ 4.304440] Registering SWP/SWPB emulation handler <6>[ 4.306266] mmc3: new DDR MMC card at address 0001 <5>[ 4.309723] Loading compiled-in X.509 certificates <6>[ 4.315437] mmcblk3: mmc3:0001 Q2J55L 7.13 GiB <6>[ 4.325192] mmcblk3boot0: mmc3:0001 Q2J55L partition 1 2.00 MiB <6>[ 4.332087] mmcblk3boot1: mmc3:0001 Q2J55L partition 2 2.00 MiB <6>[ 4.341489] mmcblk3rpmb: mmc3:0001 Q2J55L partition 3 4.00 MiB, chardev (235:0) <4>[ 4.350435] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.362892] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.374705] imx_usb 2184200.usb: No over current polarity defined <4>[ 4.390787] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.402718] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.414452] imx_usb 2184200.usb: No over current polarity defined <4>[ 4.430520] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 4.441187] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.451974] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.463817] imx_usb 2184200.usb: No over current polarity defined <4>[ 4.479971] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 4.572245] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:01: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 7.681639] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.701291] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.731328] Sending DHCP requests .., OK <6>[ 10.635497] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.205 <6>[ 10.643360] IP-Config: Complete: <6>[ 10.646859] device=eth0, hwaddr=00:04:9f:05:b8:b4, ipaddr=172.16.1.205, mask=255.255.255.0, gw=172.16.1.4 <6>[ 10.657137] host=172.16.1.205, domain=example.org, nis-domain=(none) <6>[ 10.664206] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.664211] nameserver0=172.16.1.4 <6>[ 10.679304] Freeing unused kernel memory: 2048K <6>[ 10.711776] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.838990] udevd[129]: starting version 3.2.9 <5>[ 10.844857] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.851990] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.858816] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 10.874465] udevd[129]: specified user 'tss' unknown <27>[ 10.879920] udevd[129]: specified group 'tss' unknown <30>[ 10.888185] udevd[130]: starting eudev-3.2.9 <6>[ 11.327506] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 11.335983] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.349668] imx_usb 2184200.usb: No over current polarity defined <6>[ 11.353244] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 11.368280] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 11.433870] etnaviv-gpu 130000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.436822] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.441544] etnaviv-gpu: probe of 130000.gpu failed with error -110 <4>[ 11.453705] imx_usb 2184200.usb: No over current polarity defined <4>[ 11.455556] etnaviv-gpu 134000.gpu: deferred probe timeout, ignoring dependency <6>[ 11.464836] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 11.469420] etnaviv-gpu: probe of 134000.gpu failed with error -110 <4>[ 11.473167] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 11.478031] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 11.484603] etnaviv-gpu 2204000.gpu: deferred probe timeout, ignoring dependency <6>[ 11.492843] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 11.501149] etnaviv-gpu: probe of 2204000.gpu failed with error -110 <6>[ 11.508938] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.532724] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.547618] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops [dw_hdmi_imx]) <4>[ 11.635762] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.676369] imx_usb 2184200.usb: No over current polarity defined <4>[ 11.734032] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 11.813844] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.822464] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.831009] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.839594] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.848270] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.930999] caam 2100000.crypto: Entropy delay = 3200 <6>[ 11.942585] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <6>[ 11.997192] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 12.057951] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 12.063395] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 12.070279] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 12.089010] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.093048] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 12.105516] imx_usb 2184200.usb: No over current polarity defined <4>[ 12.106608] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 12.120757] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 12.127592] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 12.129020] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 12.145450] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.145534] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 12.162596] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.171189] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 12.180044] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 12.195852] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <4>[ 12.208827] ------------[ cut here ]------------ <4>[ 12.213814] WARNING: CPU: 3 PID: 68 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <4>[ 12.223381] Modules linked in: phy_generic caam error dw_hdmi_imx dw_hdmi etnaviv gpu_sched imx_ldb imxdrm imx_ipu_v3 <4>[ 12.234364] CPU: 3 PID: 68 Comm: kworker/3:2 Not tainted 5.10.129-cip12 #1 <4>[ 12.241518] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 12.248333] Workqueue: events deferred_probe_work_func <4>[ 12.253784] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) <4>[ 12.261809] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 12.269312] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 12.276556] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) <4>[ 12.284321] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <4>[ 12.293214] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 12.302712] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 12.312121] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 12.320502] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) <4>[ 12.329135] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 12.338802] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 12.347861] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 12.356490] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 12.364943] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) <4>[ 12.373395] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 12.382192] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 12.390728] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 12.399178] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 12.408417] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 12.417823] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) <4>[ 12.426194] [] (worker_thread) from [] (kthread+0x14c/0x150) <4>[ 12.433864] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 12.441351] Exception stack(0xc30adfb0 to 0xc30adff8) <4>[ 12.446672] dfa0: 00000000 00000000 00000000 00000000 <4>[ 12.455119] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 12.463565] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 12.470506] ---[ end trace f25b5389a62c7047 ]--- <4>[ 12.478694] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.495555] imx_usb 2184200.usb: No over current polarity defined # <4>[ 12.516602] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 12.529729] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.537423] caam algorithms registered in /proc/crypto <6>[ 12.538352] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 12.545282] caam 2100000.crypto: registering rng-caam <6>[ 12.552210] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.565965] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) #<6>[ 12.574611] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) done <6>[ 12.586831] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) Saving random seed: <4>[ 12.598397] ------------[ cut here ]------------ <4>[ 12.603984] WARNING: CPU: 3 PID: 68 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <5>[ 12.610348] random: dd: uninitialized urandom read (32 bytes read) <4>[ 12.613502] Modules linked in: caam_jr caamhash_desc caamalg_desc crypto_engine libdes authenc phy_generic caam error dw_hdmi_imx dw_hdmi etnaviv gpu_sched imx_ldb imxdrm imx_ipu_v3 <4>[ 12.636539] CPU: 3 PID: 68 Comm: kworker/3:2 Tainted: G W 5.10.129-cip12 #1 <4>[ 12.645072] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) OK <4>[ 12.651880] Workqueue: events deferred_probe_work_func <4>[ 12.657685] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) Starting network: <4>[ 12.665824] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 12.674869] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 12.682158] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) ip: RTNETLINK answers: File exist<4>[ 12.689964] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) s <4>[ 12.701711] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) FAIL <4>[ 12.711456] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 12.721388] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 12.729781] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) Starting dropbear sshd: <4>[ 12.738433] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <5>[ 12.739877] random: crng init done <4>[ 12.750158] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 12.750172] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 12.750188] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 12.750205] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) OK<5>[ 12.753871] random: 1 urandom warning(s) missed due to ratelimiting <4>[ 12.762906] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 12.762920] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 12.762936] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 12.820900] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 12.830294] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 12.830312] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) <4>[ 12.848053] [] (worker_thread) from [] (kthread+0x14c/0x150) /bin/sh: <4>[ 12.855742] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 12.863982] Exception stack(0xc30adfb0 to 0xc30adff8) can't access tty; job control tur<4>[ 12.869300] dfa0: 00000000 00000000 00000000 00000000 ned off<4>[ 12.880600] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 12.889645] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 12.896576] ---[ end trace f25b5389a62c7048 ]--- / # # / # <4>[ 12.904772] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.917156] imx_usb 2184200.usb: # # No over current polarity defined <4>[ 12.933906] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 12.946500] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.955093] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 12.963693] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.972251] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 12.980954] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) #<6>[ 12.992517] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <4>[ 13.003621] ------------[ cut here ]------------ <4>[ 13.008535] WARNING: CPU: 3 PID: 68 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <4>[ 13.018075] Modules linked in: caam_jr caamhash_desc caamalg_desc crypto_engine libdes authenc phy_generic caam error dw_hdmi_imx dw_hdmi etnaviv gpu_sched imx_ldb imxdrm imx_ipu_v3 <4>[ 13.034626] CPU: 3 PID: 68 Comm: kworker/3:2 Tainted: G W 5.10.129-cip12 #1 <4>[ 13.043157] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 13.049966] Workqueue: events deferred_probe_work_func <4>[ 13.055398] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) / # <4>[ 13.063575] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 13.071419] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 13.078662] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) <4>[ 13.086425] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <4>[ 13.095310] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 13.104805] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 13.114210] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 13.122751] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) / # <4>[ 13.131379] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 13.141386] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 13.150442] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 13.159export SHELL=/bin/sh . /lava-1018545/environment 067] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) #<4>[ 13.167518] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) <4>[ 13.176046] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 13.184841] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 13.193375] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 13.201822] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 13.211056] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 13.220628] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) / # <4>[ 13.228991] [] (worker_thread) from [] (kthread+0x14c/0x150) <4>[ 13.237007] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 13.244493] Exception stack(0xc30adfb0 to 0xc30adff8) <4>[ 13.249812] dfa0: 00000000 00000000 00000000 00000000 <4>[ 13.258256] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 13.266700] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 e<4>[ 13.273622] ---[ end trace f25b5389a62c7049 ]--- xport SHELL=/bin/sh / # . /lava-1018545/environment/lava-1018545/bin/lava-test-runner /lava-1018545/0 / # /lava-1018545/bin/lava-test-runner /lava-1018545/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1018545/0/tests/0_dmesg + cat uuid + UUID=1018545_1.5.2.4<8>[ 18.798803] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.847697] <8>[ 18.891622] <8>[ 18.935164] + set<8>[ 18.945139] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1018545/environment / # . /lava-1018545/environment/lava-1018545/bin/lava-test-runner /lava-1018545/1 / # /lava-1018545/bin/lava-test-runner /lava-1018545/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1018545/1/tests/1_bootrr + cat uuid + <8>[ 24.676139] UUID=1018545_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1018545/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1018545/1/../bin/lava-test-case <8>[ 25.721905] /lava-1018545/1/../bin/lava-test-case <8>[ 25.763292] /lava-1018545/1/../bin/lava-test-case <8>[ 25.788818] + set<8>[ 25.808230] +x / #