Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3020 device /dev/ttyimx6sx-sdb-1 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03-imx_v2017.03_4.9.88_2.0.0_ga+gb76bb1b (May 01 2018 - 14:41:44 -0500) CPU: Freescale i.MX6SX rev1.4 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 31C Reset cause: POR Model: Freescale i.MX6 SoloX SDB RevB Board Board: MX6SX SABRE SDB DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x11 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment Display: Hannstar-XGA (1024x768) Video: 1024x768x18 In: serial Out: serial Err: serial switch to partitions #0, OK mmc2 is current device Net: Warning: ethernet@02188000 using MAC address from ROM Warning: ethernet@021b4000 using MAC address from ROM eth0: ethernet@02188000, eth1: ethernet@021b4000 [PRIME] Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.181 (1255 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1018540/tftp-deploy-4k8ux0p5/kernel/zImage tftp 0x80800000 1018540/tftp-deploy-4k8ux0p5/kernel/zImage Using ethernet@021b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.181; sending through gateway 172.16.1.4 Filename '1018540/tftp-deploy-4k8ux0p5/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 10.4 MiB/s done Bytes transferred = 9662976 (937200 hex) => tftp 0x86800000 1018540/tftp-deploy-4k8ux0p5/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1018540/tftp-deploy-4k8ux0p5/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@021b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.181; sending through gateway 172.16.1.4 Filename '1018540/tftp-deploy-4k8ux0p5/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 10.9 MiB/s done Bytes transferred = 16055727 (f4fdaf hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1018540/tftp-deploy-4k8ux0p5/dtb/imx6sx-sdb.dtb tftp 0x83000000 1018540/tftp-deploy-4k8ux0p5/dtb/imx6sx-sdb.dtb Using ethernet@021b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.181; sending through gateway 172.16.1.4 Filename '1018540/tftp-deploy-4k8ux0p5/dtb/imx6sx-sdb.dtb'. Load address: 0x83000000 Loading: *### 7.6 MiB/s done Bytes transferred = 39901 (9bdd hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x937200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16055663 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300cbdc Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.129-cip12 (KernelCI@build-j399661-arm-gcc-10-multi-v7-defconfig-lnr76) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jul 26 02:08:36 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 SoloX SDB RevB Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933980K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49060K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76430001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008491] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022336] Console: colour dummy device 80x30 <6>[ 0.024239] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034738] pid_max: default: 32768 minimum: 301 <6>[ 0.039764] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047244] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055896] CPU: Testing write buffer coherency: ok <6>[ 0.060464] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065982] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072399] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.079953] rcu: Hierarchical SRCU implementation. <6>[ 0.086751] EFI services will not be available. <6>[ 0.088866] smp: Bringing up secondary CPUs ... <6>[ 0.093516] smp: Brought up 1 node, 1 CPU <6>[ 0.097843] SMP: Total of 1 processors activated (6.00 BogoMIPS). <6>[ 0.104190] CPU: All CPU(s) started in SVC mode. <6>[ 0.109581] devtmpfs: initialized <6>[ 0.118816] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.124182] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.134126] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.144398] pinctrl core: initialized pinctrl subsystem <6>[ 0.148720] DMI not present or invalid. <6>[ 0.151901] NET: Registered protocol family 16 <6>[ 0.158034] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.165326] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.165455] cpuidle: using governor menu <6>[ 0.347062] vdd3p0: supplied by regulator-dummy <6>[ 0.369836] vddpcie: supplied by regulator-dummy <6>[ 0.762779] No ATAGs? <6>[ 0.762863] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.770813] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.781519] imx6sx-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.791572] Serial: AMBA PL011 UART driver <6>[ 0.824054] mxs-dma 1804000.dma-apbh: initialized <6>[ 0.835640] iommu: Default domain type: Translated <6>[ 0.839265] vgaarb: loaded <5>[ 0.841987] SCSI subsystem initialized <6>[ 0.845475] usbcore: registered new interface driver usbfs <6>[ 0.850765] usbcore: registered new interface driver hub <6>[ 0.856454] usbcore: registered new device driver usb <6>[ 0.866285] i2c i2c-0: IMX I2C adapter registered <6>[ 0.869123] i2c i2c-2: IMX I2C adapter registered <6>[ 0.874402] i2c i2c-3: IMX I2C adapter registered <6>[ 0.880105] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.883639] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.893164] PTP clock support registered <6>[ 0.901398] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.949164] NET: Registered protocol family 2 <6>[ 1.951192] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.959768] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.967372] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.975449] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.982932] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.989551] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.996427] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.003927] NET: Registered protocol family 1 <6>[ 2.009074] RPC: Registered named UNIX socket transport module. <6>[ 2.014624] RPC: Registered udp transport module. <6>[ 2.019540] RPC: Registered tcp transport module. <6>[ 2.024552] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.031270] PCI: CLS 0 bytes, default 64 <6>[ 2.036014] Trying to unpack rootfs image as initramfs... <6>[ 3.321863] Freeing initrd memory: 15680K <6>[ 3.323895] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.333427] Initialise system trusted keyrings <6>[ 3.336821] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.348873] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.352983] NFS: Registering the id_resolver key type <5>[ 3.357562] Key type id_resolver registered <5>[ 3.361991] Key type id_legacy registered <6>[ 3.366333] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.373255] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.380956] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.386103] Key type asymmetric registered <5>[ 3.389940] Asymmetric key parser 'x509' registered <6>[ 3.395196] bounce: pool size: 64 pages <6>[ 3.399250] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.406944] io scheduler mq-deadline registered <6>[ 3.411742] io scheduler kyber registered <4>[ 3.443940] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 3.468984] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.476013] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.546932] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.555823] SuperH (H)SCI(F) driver initialized <6>[ 3.558852] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 30, base_baud = 1500000) is a IMX <6>[ 3.566797] printk: console [ttymxc0] enabled <6>[ 3.566797] printk: console [ttymxc0] enabled <6>[ 3.575941] printk: bootconsole [ec_imx21] disabled <6>[ 3.575941] printk: bootconsole [ec_imx21] disabled <6>[ 3.587441] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 78, base_baud = 1500000) is a IMX <6>[ 3.599707] msm_serial: driver initialized <6>[ 3.604504] STMicroelectronics ASC driver initialized <6>[ 3.612135] STM32 USART driver initialized <6>[ 3.638654] brd: module loaded <6>[ 3.649495] loop: module loaded <6>[ 3.671116] CAN device driver interface <6>[ 3.676941] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.687029] pps pps0: new PPS source ptp0 <6>[ 3.750449] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.758516] pps pps1: new PPS source ptp1 <6>[ 4.600580] fec 21b4000.ethernet eth1: registered PHC device 1 <6>[ 4.608414] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.613707] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.619967] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.625663] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.638903] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.646691] usbcore: registered new interface driver pegasus <6>[ 4.652707] usbcore: registered new interface driver asix <6>[ 4.658410] usbcore: registered new interface driver ax88179_178a <6>[ 4.664836] usbcore: registered new interface driver cdc_ether <6>[ 4.670978] usbcore: registered new interface driver smsc75xx <6>[ 4.677069] usbcore: registered new interface driver smsc95xx <6>[ 4.683139] usbcore: registered new interface driver net1080 <6>[ 4.689099] usbcore: registered new interface driver cdc_subset <6>[ 4.695341] usbcore: registered new interface driver zaurus <6>[ 4.701245] usbcore: registered new interface driver cdc_ncm <6>[ 4.711683] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.718483] ehci-pci: EHCI PCI platform driver <6>[ 4.723286] ehci-platform: EHCI generic platform driver <6>[ 4.729169] ehci-orion: EHCI orion driver <6>[ 4.733808] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.738341] ehci-st: EHCI STMicroelectronics driver <6>[ 4.743796] ehci-exynos: EHCI Exynos driver <6>[ 4.748489] ehci-atmel: EHCI Atmel driver <6>[ 4.753065] tegra-ehci: Tegra EHCI driver <6>[ 4.757619] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.764132] ohci-pci: OHCI PCI platform driver <6>[ 4.768907] ohci-platform: OHCI generic platform driver <6>[ 4.774787] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.779321] ohci-st: OHCI STMicroelectronics driver <6>[ 4.784793] ohci-atmel: OHCI Atmel driver <6>[ 4.790509] usbcore: registered new interface driver usb-storage <6>[ 4.807052] i2c /dev entries driver <6>[ 4.836274] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.842783] sdhci: Copyright(c) Pierre Ossman <6>[ 4.850814] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.859698] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.874363] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.879626] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.886240] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.891570] sdhci-esdhc-imx 219c000.mmc: Got WP GPIO <6>[ 4.898657] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.906378] usbcore: registered new interface driver usbhid <6>[ 4.912290] usbhid: USB HID core driver <6>[ 4.924814] NET: Registered protocol family 10 <6>[ 4.930743] Segment Routing with IPv6 <6>[ 4.934814] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.941673] NET: Registered protocol family 17 <6>[ 4.946401] can: controller area network core <6>[ 4.951096] NET: Registered protocol family 29 <6>[ 4.955866] can: raw protocol <6>[ 4.959106] can: broadcast manager protocol <6>[ 4.963587] can: netlink gateway - max_hops=1 <5>[ 4.968742] Key type dns_resolver registered <6>[ 4.974441] ThumbEE CPU extension supported. <5>[ 4.978995] Registering SWP/SWPB emulation handler <5>[ 4.984585] Loading compiled-in X.509 certificates <4>[ 5.018610] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 5.027706] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 5.035238] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 5.042686] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <4>[ 5.054668] imx_usb 2184000.usb: No over current polarity defined <4>[ 5.073568] imx_usb 2184200.usb: No over current polarity defined <6>[ 5.085011] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 5.090242] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <3>[ 5.102535] mxs_phy 20c9000.usbphy: vbus is not valid <6>[ 5.122343] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 5.128977] hub 1-0:1.0: USB hub found <6>[ 5.133136] hub 1-0:1.0: 1 port detected <4>[ 5.150377] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 5.174572] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 5.187842] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 5.208775] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 5.236301] mmc3: new high speed SDHC card at address 0001 <6>[ 5.242826] mmcblk3: mmc3:0001 SD16G 14.5 GiB <6>[ 5.251961] mmcblk3: p1 p2 <4>[ 5.268238] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 5.304730] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:01: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 5.364301] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:02: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:02, irq=POLL) <6>[ 8.484442] fec 21b4000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off <6>[ 8.492395] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready <5>[ 8.524160] Sending DHCP requests .., OK <6>[ 11.408273] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.181 <6>[ 11.416138] IP-Config: Complete: <6>[ 11.419638] device=eth1, hwaddr=00:04:9f:06:06:f6, ipaddr=172.16.1.181, mask=255.255.255.0, gw=172.16.1.4 <6>[ 11.429920] host=172.16.1.181, domain=example.org, nis-domain=(none) <6>[ 11.436988] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 11.436993] nameserver0=172.16.1.4 <6>[ 11.458177] Freeing unused kernel memory: 2048K <6>[ 11.474446] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.643965] udevd[131]: starting version 3.2.9 <5>[ 11.649892] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.657520] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.664519] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 11.681208] udevd[131]: specified user 'tss' unknown <27>[ 11.686858] udevd[131]: specified group 'tss' unknown <30>[ 11.703189] udevd[132]: starting eudev-3.2.9 <4>[ 13.360026] etnaviv-gpu 1800000.gpu: deferred probe timeout, ignoring dependency <4>[ 13.367813] etnaviv-gpu: probe of 1800000.gpu failed with error -110 <4>[ 13.392082] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 13.686654] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 14.823397] caam 2100000.crypto: Entropy delay = 12000 <6>[ 15.056263] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 15.283687] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.289100] caam 2100000.crypto: device ID = 0x0a16010000000200 (Era 4) <6>[ 15.295996] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 15.318772] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 15.621555] spi-nor spi5.0: n25q256a (32768 Kbytes) <4>[ 15.695215] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 15.704662] spi-nor spi5.2: n25q256a (32768 Kbytes) <4>[ 15.925491] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 16.176385] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 16.184613] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 16.205956] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 17.340875] caam algorithms registered in /proc/crypto <6>[ 17.348006] caam 2100000.crypto: registering rng-caam <4>[ 17.367163] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 17.413661] pwm-backlight backlight-display: supply power not found, using dummy regulator done Saving random seed: <5>[ 17.450845] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 17.547360] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh expor<5>[ 18.035867] random: crng init done t SHELL=/bin/sh / # . /lava-1018540/environment . /lava-1018540/environment / # /lava-1018540/bin/lava-test-runner /lava-1018540/0 /lava-1018540/bin/lava-test-runner /lava-1018540/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1018540/0/tests/0_dmesg + cat uuid + UUID=1018540_1.5.2.4<8>[ 23.371789] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 23.422332] <8>[ 23.467814] <8>[ 23.513769] + set +x <8>[ 23.524130] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1018540/environment / # . /lava-1018540/environment/lava-1018540/bin/lava-test-runner /lava-1018540/1 / # /lava-1018540/bin/lava-test-runner /lava-1018540/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1018540/1/tests/1_bootrr + cat uuid <8>[ 29.257189] + UUID=1018540_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1018540/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1018540/1/../bin/lava-test-case <8>[ 30.303537] /lava-1018540/1/../bin/lava-test-case <8>[ 30.345907] /lava-1018540/1/../bin/lava-test-case <8>[ 30.372307] + set +x <8>[ 30.392476] / #