Trying 192.168.1.205... Connected to ts5. Escape character is '^]'. ser2net port telnet,2000 device serialdev,/dev/ttyUSB-lf-bbb-01,115200n81,local [] (Debian GNU/Linux) U-Boot SPL 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) Trying to boot from MMC2 U-Boot 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 172.16.3.210 (76 ms) => setenv serverip 172.16.3.3 setenv serverip 172.16.3.3 => tftp 0x82000000 716250/tftp-deploy-peaob6rh/kernel/zImage tftp 0x82000000 716250/tftp-deploy-peaob6rh/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.210 Filename '716250/tftp-deploy-peaob6rh/kernel/zImage'. Load address: 0x82000000 Loading: *################################################## 4.4 MiB 5.2 MiB/s done Bytes transferred = 4589608 (460828 hex) => tftp 0x83000000 716250/tftp-deploy-peaob6rh/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 716250/tftp-deploy-peaob6rh/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.210 Filename '716250/tftp-deploy-peaob6rh/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################## 13.5 MiB 5.2 MiB/s done Bytes transferred = 14130688 (d79e00 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 716250/tftp-deploy-peaob6rh/dtb/am335x-boneblack.dtb tftp 0x88000000 716250/tftp-deploy-peaob6rh/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.210 Filename '716250/tftp-deploy-peaob6rh/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *################################################## 61.4 KiB 4.6 MiB/s done Bytes transferred = 62852 (f584 hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x460828 ] ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2022-07-26 2:18:13 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14130624 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 88012583 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.129-cip12 (KernelCI@build-j399562-arm-gcc-10-omap2plus-defconfig-svcnj) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jul 26 02:00:15 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472068K/522240K available (9216K kernel code, 1024K rwdata, 2164K rodata, 1024K init, 281K bss, 33788K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018565] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030197] Console: colour dummy device 80x30 <3>[ 0.035068] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042129] This ensures that you still see kernel messages. Please <3>[ 0.048856] update your kernel commandline. <6>[ 0.053459] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095544] pid_max: default: 32768 minimum: 301 <6>[ 0.100715] LSM: Security Framework initializing <6>[ 0.105830] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.113649] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.122928] CPU: Testing write buffer coherency: ok <6>[ 0.128293] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.134213] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140703] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147895] rcu: Hierarchical SRCU implementation. <6>[ 0.153722] smp: Bringing up secondary CPUs ... <6>[ 0.158657] smp: Brought up 1 node, 1 CPU <6>[ 0.163110] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169851] CPU: All CPU(s) started in SVC mode. <6>[ 0.175613] devtmpfs: initialized <6>[ 0.191264] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199798] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210234] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218781] pinctrl core: initialized pinctrl subsystem <6>[ 0.226388] NET: Registered protocol family 16 <6>[ 0.233959] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260680] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266753] audit: initializing netlink subsys (disabled) <6>[ 0.273790] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273804] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280415] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287130] cpuidle: using governor menu <5>[ 1.183918] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.311737] No ATAGs? <6>[ 1.314362] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.338762] Kprobes globally optimized <6>[ 1.351906] iommu: Default domain type: Translated <6>[ 1.359052] vgaarb: loaded <5>[ 1.362626] SCSI subsystem initialized <6>[ 1.367676] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.373221] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.382945] PTP clock support registered <6>[ 1.388618] clocksource: Switched to clocksource dmtimer <5>[ 2.052300] VFS: Disk quotas dquot_6.6.0 <6>[ 2.056716] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.073766] NET: Registered protocol family 2 <6>[ 2.078945] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.087560] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.096525] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.104823] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.112503] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.119443] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.126446] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.134075] NET: Registered protocol family 1 <6>[ 2.139903] RPC: Registered named UNIX socket transport module. <6>[ 2.146276] RPC: Registered udp transport module. <6>[ 2.151472] RPC: Registered tcp transport module. <6>[ 2.156579] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.163507] PCI: CLS 0 bytes, default 64 <6>[ 2.168647] Trying to unpack rootfs image as initramfs... <6>[ 3.153000] Freeing initrd memory: 13800K <6>[ 3.158753] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.169214] Initialise system trusted keyrings <6>[ 3.174651] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.182881] NFS: Registering the id_resolver key type <5>[ 3.188494] Key type id_resolver registered <5>[ 3.193068] Key type id_legacy registered <6>[ 3.197509] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.205508] Key type asymmetric registered <5>[ 3.210049] Asymmetric key parser 'x509' registered <6>[ 3.215349] io scheduler mq-deadline registered <6>[ 3.220297] io scheduler kyber registered <3>[ 3.361000] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.369683] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.480424] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.522648] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.594802] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.603501] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.664301] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.672996] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.690654] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.699329] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.763558] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.772115] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.799921] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.814293] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.825061] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.834486] printk: console [ttyS0] enabled <6>[ 3.834486] printk: console [ttyS0] enabled <6>[ 3.843563] printk: bootconsole [omap8250] disabled <6>[ 3.843563] printk: bootconsole [omap8250] disabled <6>[ 3.867239] brd: module loaded <6>[ 3.879717] loop: module loaded <3>[ 3.885106] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.958503] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.000968] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.010890] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.017543] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.023361] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.030914] cpsw 4a100000.ethernet: Detected MACID = 34:03:de:5e:2c:05 <6>[ 4.039934] i2c /dev entries driver <5>[ 4.045422] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.053345] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.059887] sdhci: Copyright(c) Pierre Ossman <6>[ 4.065221] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.073506] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.083300] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.091740] Initializing XFRM netlink socket <6>[ 4.096543] NET: Registered protocol family 10 <6>[ 4.102994] Segment Routing with IPv6 <6>[ 4.107038] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.114118] NET: Registered protocol family 17 <6>[ 4.118973] NET: Registered protocol family 15 <5>[ 4.123827] Key type dns_resolver registered <6>[ 4.129016] oprofile: using arm/armv7 <6>[ 4.133055] ThumbEE CPU extension supported. <5>[ 4.137629] Registering SWP/SWPB emulation handler <3>[ 4.143183] omap_voltage_late_init: Voltage driver support not added <3>[ 4.149902] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.158293] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.166975] SmartReflex Class3 initialized <6>[ 4.172006] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.180941] Loading compiled-in X.509 certificates <6>[ 4.205678] OMAP GPIO hardware version 0.1 <4>[ 4.239127] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.252717] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.261532] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.267858] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.277765] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.289196] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.298208] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.303442] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.316754] mmc1: new high speed MMC card at address 0001 <6>[ 4.323664] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.329218] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.335875] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.342481] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.352018] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.361004] mmcblk1: p1 <6>[ 4.369233] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.460008] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 6.609161] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.638490] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.668585] Sending DHCP requests ., OK <6>[ 6.792588] IP-Config: Got DHCP answer from 172.16.3.3, my address is 172.16.3.210 <6>[ 6.800492] IP-Config: Complete: <6>[ 6.804001] device=eth0, hwaddr=34:03:de:5e:2c:05, ipaddr=172.16.3.210, mask=255.255.255.0, gw=172.16.3.3 <6>[ 6.814333] host=172.16.3.210, domain=denx.de, nis-domain=(none) <6>[ 6.821083] bootserver=172.16.3.33, rootserver=172.16.3.33, rootpath= <6>[ 6.821090] nameserver0=172.16.3.3 <6>[ 6.832388] ntpserver0=172.16.3.3 <6>[ 6.839285] Freeing unused kernel memory: 1024K <6>[ 6.848968] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.084078] udevd[101]: starting version 3.2.9 <5>[ 7.090892] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.098045] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.105707] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.122942] udevd[101]: specified user 'tss' unknown <27>[ 7.129194] udevd[101]: specified group 'tss' unknown <30>[ 7.141152] udevd[102]: starting eudev-3.2.9 <6>[ 7.897068] remoteproc remoteproc0: wkup_m3 is available <6>[ 8.078183] usbcore: registered new interface driver usbfs <6>[ 8.084269] usbcore: registered new interface driver hub <6>[ 8.090016] usbcore: registered new device driver usb <4>[ 8.101681] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.110901] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 8.313656] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.322813] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 8.544456] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 8.550309] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 8.747267] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 8.778852] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 8.787447] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 8.795052] usb usb1: Product: MUSB HDRC host driver <6>[ 8.800331] usb usb1: Manufacturer: Linux 5.10.129-cip12 musb-hcd <6>[ 8.806714] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 8.968836] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 8.976503] at24 2-0054: supply vcc not found, using dummy regulator <3>[ 8.998246] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 9.061577] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <4>[ 9.152932] at24 2-0055: supply vcc not found, using dummy regulator <6>[ 9.169695] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 9.189323] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 9.230266] hub 1-0:1.0: USB hub found <4>[ 9.255759] at24 2-0056: supply vcc not found, using dummy regulator <6>[ 9.275469] hub 1-0:1.0: 1 port detected <6>[ 9.361655] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 9.367133] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 9.378812] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 9.489009] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.521995] tda998x 0-0070: found TDA19988 <3>[ 9.610902] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.937093] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <3>[ 9.959020] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 10.028992] remoteproc remoteproc0: powering up wkup_m3 <4>[ 10.034653] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 10.044584] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 10.050825] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 10.684872] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 10.777296] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 10.837889] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 10.845022] random: crng init done <6>[ 10.863403] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.891523] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 11.114601] PM: Cannot get wkup_m3_ipc handle <6>[ 11.272776] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 11.338555] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 11.377234] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 11.500165] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 11.525750] PM: Cannot get wkup_m3_ipc handle <3>[ 11.573872] PM: Cannot get wkup_m3_ipc handle <3>[ 12.024440] PM: Cannot get wkup_m3_ipc handle <3>[ 12.059574] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-716250/environment . /lava-716250/environment / # /lava-716250/bin/lava-test-runner /lava-716250/0 /lava-716250/bin/lava-test-runner /lava-716250/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-716250/0/tests/0_dmesg + cat uuid + UUID=716250_1.5.2.4.1 + <8>[ 12.994122] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.059873] <8>[ 13.119809] <8>[ 13.179924] + set +x <8>[ 13.191042] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-716250/environment / # . /lava-716250/environment/lava-716250/bin/lava-test-runner /lava-716250/1 / # /lava-716250/bin/lava-test-runner /lava-716250/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-716250/1/tests/1_bootrr + cat uuid + UUID=716250_1.5.2.4.5 <8>[ 13.727333] + set +x + export 'PATH=/opt/bootrr/helpers:/lava-716250/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-716250/1/../bin/lava-test-case <8>[ 14.809486] /lava-716250/1/../bin/lava-test-case <8>[ 14.863954] /lava-716250/1/../bin/lava-test-case <8>[ 14.896703] + set +x <8>[ 14.924874] / #