Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.3 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 716491/tftp-deploy-tp2ubs_k/kernel/zImage tftp 0x82000000 716491/tftp-deploy-tp2ubs_k/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.3 Filename '716491/tftp-deploy-tp2ubs_k/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 5.1 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x83000000 716491/tftp-deploy-tp2ubs_k/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 716491/tftp-deploy-tp2ubs_k/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.3 Filename '716491/tftp-deploy-tp2ubs_k/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 5.2 MiB/s done Bytes transferred = 16048530 (f4e192 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 716491/tftp-deploy-tp2ubs_k/dtb/am335x-boneblack.dtb tftp 0x88000000 716491/tftp-deploy-tp2ubs_k/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.3 Filename '716491/tftp-deploy-tp2ubs_k/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62852 (f584 hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2022-07-26 14:09:28 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16048466 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 88012583 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.129-cip12 (KernelCI@build-j402803-arm-gcc-10-multi-v7-defconfig-zl75c) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jul 26 13:48:53 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 411904K/522240K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 44800K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008338] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019056] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033104] Console: colour dummy device 80x30 <3>[ 0.037968] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045013] This ensures that you still see kernel messages. Please <3>[ 0.051730] update your kernel commandline. <6>[ 0.056335] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096021] pid_max: default: 32768 minimum: 301 <6>[ 0.101228] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.109014] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.118011] CPU: Testing write buffer coherency: ok <6>[ 0.123401] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.129181] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135487] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.144710] rcu: Hierarchical SRCU implementation. <6>[ 0.154613] EFI services will not be available. <6>[ 0.159799] smp: Bringing up secondary CPUs ... <6>[ 0.164730] smp: Brought up 1 node, 1 CPU <6>[ 0.169120] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.175855] CPU: All CPU(s) started in SVC mode. <6>[ 0.181468] devtmpfs: initialized <6>[ 0.195787] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.204311] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214739] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.225867] pinctrl core: initialized pinctrl subsystem <6>[ 0.234126] DMI not present or invalid. <6>[ 0.239103] NET: Registered protocol family 16 <6>[ 0.246487] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.273156] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.281256] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.281454] cpuidle: using governor menu <6>[ 1.329064] No ATAGs? <6>[ 1.331740] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.346146] Serial: AMBA PL011 UART driver <6>[ 1.384156] iommu: Default domain type: Translated <6>[ 1.389978] vgaarb: loaded <5>[ 1.393976] SCSI subsystem initialized <6>[ 1.398749] usbcore: registered new interface driver usbfs <6>[ 1.404833] usbcore: registered new interface driver hub <6>[ 1.410632] usbcore: registered new device driver usb <6>[ 1.417855] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.423283] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.432977] PTP clock support registered <6>[ 1.441385] clocksource: Switched to clocksource dmtimer <6>[ 2.400425] NET: Registered protocol family 2 <6>[ 2.405590] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.414089] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.423020] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.431286] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.438964] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.445896] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.452917] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.460480] NET: Registered protocol family 1 <6>[ 2.466095] RPC: Registered named UNIX socket transport module. <6>[ 2.472539] RPC: Registered udp transport module. <6>[ 2.477644] RPC: Registered tcp transport module. <6>[ 2.482766] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.489662] PCI: CLS 0 bytes, default 64 <6>[ 2.494683] Trying to unpack rootfs image as initramfs... <6>[ 3.567253] Freeing initrd memory: 15676K <6>[ 3.572652] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.582985] Initialise system trusted keyrings <6>[ 3.588243] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.601321] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.608662] NFS: Registering the id_resolver key type <5>[ 3.614299] Key type id_resolver registered <5>[ 3.618871] Key type id_legacy registered <6>[ 3.623414] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.630574] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.638504] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.643846] Key type asymmetric registered <5>[ 3.648333] Asymmetric key parser 'x509' registered <6>[ 3.653709] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.661607] io scheduler mq-deadline registered <6>[ 3.666530] io scheduler kyber registered <3>[ 3.818235] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.826940] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.945153] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.989520] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.065985] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.074674] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.139114] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.147810] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.166223] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.174931] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.242820] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.251269] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.293487] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.395611] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.407791] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.417222] printk: console [ttyS0] enabled <6>[ 4.417222] printk: console [ttyS0] enabled <6>[ 4.426276] printk: bootconsole [omap8250] disabled <6>[ 4.426276] printk: bootconsole [omap8250] disabled <6>[ 4.440019] SuperH (H)SCI(F) driver initialized <6>[ 4.447029] msm_serial: driver initialized <6>[ 4.451938] STMicroelectronics ASC driver initialized <6>[ 4.460029] STM32 USART driver initialized <6>[ 4.467486] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 4.487778] random: crng init done <6>[ 4.500969] brd: module loaded <6>[ 4.512232] loop: module loaded <6>[ 4.537209] CAN device driver interface <6>[ 4.543377] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.551581] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.556837] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.563184] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.568870] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.641488] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.677848] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.687795] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.694502] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.700345] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.709484] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.717417] usbcore: registered new interface driver pegasus <6>[ 4.723455] usbcore: registered new interface driver asix <6>[ 4.729171] usbcore: registered new interface driver ax88179_178a <6>[ 4.735610] usbcore: registered new interface driver cdc_ether <6>[ 4.741807] usbcore: registered new interface driver smsc75xx <6>[ 4.747878] usbcore: registered new interface driver smsc95xx <6>[ 4.753979] usbcore: registered new interface driver net1080 <6>[ 4.759953] usbcore: registered new interface driver cdc_subset <6>[ 4.766207] usbcore: registered new interface driver zaurus <6>[ 4.772146] usbcore: registered new interface driver cdc_ncm <6>[ 4.783641] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.790477] ehci-pci: EHCI PCI platform driver <6>[ 4.795311] ehci-platform: EHCI generic platform driver <6>[ 4.801297] ehci-orion: EHCI orion driver <6>[ 4.806024] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.810626] ehci-st: EHCI STMicroelectronics driver <6>[ 4.816150] ehci-exynos: EHCI Exynos driver <6>[ 4.820906] ehci-atmel: EHCI Atmel driver <6>[ 4.825539] tegra-ehci: Tegra EHCI driver <6>[ 4.830179] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.836742] ohci-pci: OHCI PCI platform driver <6>[ 4.841573] ohci-platform: OHCI generic platform driver <6>[ 4.847537] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.852206] ohci-st: OHCI STMicroelectronics driver <6>[ 4.857668] ohci-atmel: OHCI Atmel driver <6>[ 4.863662] usbcore: registered new interface driver usb-storage <6>[ 4.880753] i2c /dev entries driver <5>[ 4.912856] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.921049] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.927623] sdhci: Copyright(c) Pierre Ossman <6>[ 4.936461] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.945826] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.960660] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.995466] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.004969] usbcore: registered new interface driver usbhid <6>[ 5.010906] usbhid: USB HID core driver <6>[ 5.024490] NET: Registered protocol family 10 <6>[ 5.030737] Segment Routing with IPv6 <6>[ 5.034863] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.041847] NET: Registered protocol family 17 <6>[ 5.046593] can: controller area network core <6>[ 5.051311] NET: Registered protocol family 29 <6>[ 5.056109] can: raw protocol <6>[ 5.059357] can: broadcast manager protocol <6>[ 5.063848] can: netlink gateway - max_hops=1 <5>[ 5.069248] Key type dns_resolver registered <6>[ 5.074012] ThumbEE CPU extension supported. <5>[ 5.078583] Registering SWP/SWPB emulation handler <3>[ 5.084113] omap_voltage_late_init: Voltage driver support not added <6>[ 5.092298] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 5.101053] Loading compiled-in X.509 certificates <6>[ 5.122662] OMAP GPIO hardware version 0.1 <4>[ 5.152016] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 5.165275] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 5.180278] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 5.186649] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 5.194204] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 5.202226] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 5.212201] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 5.222666] mmc1: new high speed MMC card at address 0001 <6>[ 5.229228] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.234479] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.241006] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.247626] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.257137] mmcblk1: p1 <4>[ 5.261272] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.294062] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.325132] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.364018] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.387723] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.396907] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.402041] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.465134] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.476881] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.563254] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 8.752282] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.761529] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.791537] Sending DHCP requests ., OK <6>[ 8.835650] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.3 <6>[ 8.843797] IP-Config: Complete: <6>[ 8.847337] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.3, mask=255.255.255.0, gw=192.168.11.1 <6>[ 8.857922] host=192.168.11.3, domain=usen.ad.jp, nis-domain=(none) <6>[ 8.864989] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.865009] nameserver0=192.168.11.1 <6>[ 8.888986] Freeing unused kernel memory: 2048K <6>[ 8.912560] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.114227] udevd[98]: starting version 3.2.9 <27>[ 9.130271] udevd[98]: specified user 'tss' unknown <27>[ 9.136053] udevd[98]: specified group 'tss' unknown <30>[ 9.153512] udevd[99]: starting eudev-3.2.9 <4>[ 10.850499] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 10.859658] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 11.107798] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.116930] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 11.337691] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 11.343486] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 11.553179] hub 1-0:1.0: USB hub found <6>[ 11.621534] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-716491/environment . /lava-716491/environment / # /lava-716491/bin/lava-test-runner /lava-716491/0 /lava-716491/bin/lava-test-runner /lava-716491/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-716491/0/tests/0_dmesg + cat uuid + UUID=716491_1.5.2.4.1 + <8>[ 16.318335] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.375015] <8>[ 16.426680] <8>[ 16.478413] + set +x <8>[ 16.489285] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-716491/environment / # . /lava-716491/environment/lava-716491/bin/lava-test-runner /lava-716491/1 / # /lava-716491/bin/lava-test-runner /lava-716491/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-716491/1/tests/1_bootrr + cat uuid + UUID=716491_1.5.2.4.5 + <8>[ 17.015531] set +x + export 'PATH=/opt/bootrr/helpers:/lava-716491/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-716491/1/../bin/lava-test-case <8>[ 18.089682] /lava-716491/1/../bin/lava-test-case <8>[ 18.138893] /lava-716491/1/../bin/lava-test-case <8>[ 18.168940] + set +x <8>[ 18.194135] / #