[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 6963069/tftp-deploy-uwimq0cx/kernel/zImage tftp 0x10000000 6963069/tftp-deploy-uwimq0cx/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '6963069/tftp-deploy-uwimq0cx/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 2.6 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x14000000 6963069/tftp-deploy-uwimq0cx/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 6963069/tftp-deploy-uwimq0cx/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '6963069/tftp-deploy-uwimq0cx/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 3 MiB/s done Bytes transferred = 16032448 (f4a2c0 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 6963069/tftp-deploy-uwimq0cx/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 6963069/tftp-deploy-uwimq0cx/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '6963069/tftp-deploy-uwimq0cx/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.7 MiB/s done Bytes transferred = 42397 (a59d hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16032384 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d59c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.131-cip13 (KernelCI@build-j448477-arm-gcc-10-multi-v7-defconfig-9k75h) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 3 16:37:45 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933732K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49308K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008094] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021751] Console: colour dummy device 80x30 <6>[ 0.023639] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034314] pid_max: default: 32768 minimum: 301 <6>[ 0.039351] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046767] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055379] CPU: Testing write buffer coherency: ok <6>[ 0.059894] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065426] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071795] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079464] rcu: Hierarchical SRCU implementation. <6>[ 0.086465] EFI services will not be available. <6>[ 0.088701] smp: Bringing up secondary CPUs ... <6>[ 0.093975] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.093983] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105316] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105324] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116510] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116518] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.126979] smp: Brought up 1 node, 4 CPUs <6>[ 0.131210] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.137756] CPU: All CPU(s) started in SVC mode. <6>[ 0.143180] devtmpfs: initialized <6>[ 0.153702] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159040] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168914] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179100] pinctrl core: initialized pinctrl subsystem <6>[ 0.183508] DMI not present or invalid. <6>[ 0.186702] NET: Registered protocol family 16 <6>[ 0.193921] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200496] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200670] cpuidle: using governor menu <6>[ 0.208828] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.385573] vdd1p1: supplied by regulator-dummy <6>[ 0.394590] vdd3p0: supplied by regulator-dummy <6>[ 0.403528] vdd2p5: supplied by regulator-dummy <6>[ 0.412522] vddarm: supplied by regulator-dummy <6>[ 0.421645] vddpu: supplied by regulator-dummy <6>[ 0.430386] vddsoc: supplied by regulator-dummy <6>[ 0.755284] No ATAGs? <6>[ 0.755464] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.763247] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.773371] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.783585] Serial: AMBA PL011 UART driver <6>[ 0.787751] printk: console [ramoops-1] enabled <6>[ 0.790087] pstore: Registered ramoops as persistent store backend <6>[ 0.796343] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.827611] mxs-dma 110000.dma-apbh: initialized <6>[ 0.837209] iommu: Default domain type: Translated <6>[ 0.839939] vgaarb: loaded <5>[ 0.843313] SCSI subsystem initialized <6>[ 0.847085] usbcore: registered new interface driver usbfs <6>[ 0.852246] usbcore: registered new interface driver hub <6>[ 0.857826] usbcore: registered new device driver usb <6>[ 0.864609] i2c i2c-0: IMX I2C adapter registered <6>[ 0.869389] i2c i2c-1: IMX I2C adapter registered <6>[ 0.873788] i2c i2c-2: IMX I2C adapter registered <6>[ 0.879296] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.883172] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.892606] PTP clock support registered <6>[ 0.900253] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.954403] NET: Registered protocol family 2 <6>[ 1.956611] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.965031] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.972497] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.980552] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.987974] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.994689] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.001404] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.008801] NET: Registered protocol family 1 <6>[ 2.013857] RPC: Registered named UNIX socket transport module. <6>[ 2.019424] RPC: Registered udp transport module. <6>[ 2.024414] RPC: Registered tcp transport module. <6>[ 2.029339] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.036065] PCI: CLS 0 bytes, default 64 <6>[ 2.040741] Trying to unpack rootfs image as initramfs... <6>[ 3.386401] Freeing initrd memory: 15660K <4>[ 3.388261] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.395741] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.405403] Initialise system trusted keyrings <6>[ 3.408559] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.420819] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.424764] NFS: Registering the id_resolver key type <5>[ 3.429431] Key type id_resolver registered <5>[ 3.433839] Key type id_legacy registered <6>[ 3.438170] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.445051] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.452731] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.457775] Key type asymmetric registered <5>[ 3.461677] Asymmetric key parser 'x509' registered <6>[ 3.466826] bounce: pool size: 64 pages <6>[ 3.470919] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.478529] io scheduler mq-deadline registered <6>[ 3.483328] io scheduler kyber registered <4>[ 3.530117] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.537059] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.600457] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.608618] SuperH (H)SCI(F) driver initialized <6>[ 3.611615] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.620471] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.628334] printk: console [ttymxc1] enabled <6>[ 3.628334] printk: console [ttymxc1] enabled <6>[ 3.637536] printk: bootconsole [ec_imx21] disabled <6>[ 3.637536] printk: bootconsole [ec_imx21] disabled <6>[ 3.649242] msm_serial: driver initialized <6>[ 3.655279] STMicroelectronics ASC driver initialized <6>[ 3.662564] STM32 USART driver initialized <4>[ 3.677937] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.685870] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.692705] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.709336] brd: module loaded <6>[ 3.722717] loop: module loaded <6>[ 3.729973] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.738231] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.746520] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.754991] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.763008] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.770764] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.778311] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.788925] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.796215] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.805310] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.816131] scsi host0: ahci-imx <6>[ 3.819993] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.840607] CAN device driver interface <6>[ 3.846037] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.855562] pps pps0: new PPS source ptp0 <6>[ 3.892284] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.899860] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.905118] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.911386] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.917054] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.928996] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.936722] usbcore: registered new interface driver pegasus <6>[ 3.942710] usbcore: registered new interface driver asix <6>[ 3.948407] usbcore: registered new interface driver ax88179_178a <6>[ 3.954841] usbcore: registered new interface driver cdc_ether <6>[ 3.961002] usbcore: registered new interface driver smsc75xx <6>[ 3.967055] usbcore: registered new interface driver smsc95xx <6>[ 3.973117] usbcore: registered new interface driver net1080 <6>[ 3.979072] usbcore: registered new interface driver cdc_subset <6>[ 3.985305] usbcore: registered new interface driver zaurus <6>[ 3.991234] usbcore: registered new interface driver cdc_ncm <6>[ 4.000725] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.007522] ehci-pci: EHCI PCI platform driver <6>[ 4.012297] ehci-platform: EHCI generic platform driver <6>[ 4.018078] ehci-orion: EHCI orion driver <6>[ 4.022606] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.027067] ehci-st: EHCI STMicroelectronics driver <6>[ 4.032422] ehci-exynos: EHCI Exynos driver <6>[ 4.037058] ehci-atmel: EHCI Atmel driver <6>[ 4.041535] tegra-ehci: Tegra EHCI driver <6>[ 4.046019] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.052499] ohci-pci: OHCI PCI platform driver <6>[ 4.057250] ohci-platform: OHCI generic platform driver <6>[ 4.063025] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.067496] ohci-st: OHCI STMicroelectronics driver <6>[ 4.072847] ohci-atmel: OHCI Atmel driver <6>[ 4.078196] usbcore: registered new interface driver usb-storage <6>[ 4.092607] i2c /dev entries driver <6>[ 4.115745] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.122259] sdhci: Copyright(c) Pierre Ossman <6>[ 4.129597] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.137840] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.145103] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.145308] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.150421] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.160573] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.166553] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.173125] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.180616] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.187491] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.187937] usbcore: registered new interface driver usbhid <6>[ 4.194878] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.200523] usbhid: USB HID core driver <6>[ 4.218344] NET: Registered protocol family 10 <6>[ 4.224265] Segment Routing with IPv6 <6>[ 4.228276] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.235049] NET: Registered protocol family 17 <6>[ 4.239771] can: controller area network core <6>[ 4.244512] NET: Registered protocol family 29 <6>[ 4.249225] can: raw protocol <6>[ 4.252496] can: broadcast manager protocol <6>[ 4.256955] can: netlink gateway - max_hops=1 <5>[ 4.261991] Key type dns_resolver registered <6>[ 4.268271] ThumbEE CPU extension supported. <5>[ 4.272852] Registering SWP/SWPB emulation handler <5>[ 4.278257] Loading compiled-in X.509 certificates <6>[ 4.289078] pstore: Using crash dump compression: deflate <4>[ 4.320919] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.328830] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.337151] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.345613] mmc2: new high speed SDHC card at address 0001 <6>[ 4.352295] mmcblk2: mmc2:0001 SD 14.8 GiB <4>[ 4.354766] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.366917] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.372137] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 4.386156] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.393853] GPT:29296874 != 30965759 <4>[ 4.397695] GPT:Alternate GPT header not at the end of the disk. <6>[ 4.400238] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <4>[ 4.403995] GPT:29296874 != 30965759 <4>[ 4.413497] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.413909] hub 1-0:1.0: USB hub found <6>[ 4.418945] mmcblk2: p1 p2 p3 <6>[ 4.423004] hub 1-0:1.0: 1 port detected <3>[ 4.432782] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 4.440406] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 4.448778] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 4.461065] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.468965] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.477179] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.490272] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.498168] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.506357] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.516718] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.529440] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.537410] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.545723] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.559466] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.770312] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.971962] hub 1-1:1.0: USB hub found <6>[ 4.976197] hub 1-1:1.0: 3 ports detected <4>[ 4.990702] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.998804] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.008680] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.640782] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 6.670369] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.700321] Sending DHCP requests ., OK <6>[ 6.744483] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 <6>[ 6.752904] IP-Config: Complete: <6>[ 6.756424] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 <6>[ 6.767272] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 6.776291] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 6.776302] nameserver0=192.168.101.1 <6>[ 6.795269] Freeing unused kernel memory: 2048K <6>[ 6.821207] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.977187] udevd[129]: starting version 3.2.9 <5>[ 6.983078] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.990023] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.996967] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.012432] udevd[129]: specified user 'tss' unknown <27>[ 7.017886] udevd[129]: specified group 'tss' unknown <30>[ 7.026113] udevd[130]: starting eudev-3.2.9 <6>[ 7.503540] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.511005] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.521333] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.529300] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.552752] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.602474] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.611120] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.619746] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.628444] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.632162] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.644880] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.717271] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.736214] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.744240] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.802903] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.891879] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.898692] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.930369] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.944216] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.951110] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.964868] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.025632] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.031081] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.037970] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.048488] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.054984] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.061451] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.094788] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.103545] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.112159] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.120716] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.129255] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.151854] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.159815] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.168895] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.198293] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.205207] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.206969] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.214988] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.223321] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.231926] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.240278] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.265345] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.266767] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.281856] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.289530] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.291331] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.310460] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.314096] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.327021] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.335662] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.344255] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.355555] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.363602] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.408043] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.431856] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.440464] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.449026] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.457650] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.468789] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.477171] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.694273] caam algorithms registered in /proc/crypto <6>[ 8.701581] caam 2100000.crypto: registering rng-caam <4>[ 8.708897] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.725206] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) done <6>[ 8.733811] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.742768] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.751331] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Saving random seed: <4>[ 8.773016] panel-simple panel-lcd: supply power not found, using dummy regulator <5>[ 8.774199] random: dd: uninitialized urandom read (32 bytes read) <4>[ 8.781007] panel-simple panel-lcd: Specify missing connector_type OK <4>[ 8.796463] panel-simple panel-lvds0: supply power not found, using dummy regulator Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.889354] random: crng init done <5>[ 8.893264] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-6963069/environment . /lava-6963069/environment / # /lava-6963069/bin/lava-test-runner /lava-6963069/0 /lava-6963069/bin/lava-test-runner /lava-6963069/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-6963069/0/tests/0_dmesg + cat uuid + UUID=6963069_1.5.2.4.1<8>[ 9.488892] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.534929] <8>[ 9.588401] <8>[ 9.631255] + set<8>[ 9.641221] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-6963069/environment / # . /lava-6963069/environment/lava-6963069/bin/lava-test-runner /lava-6963069/1 / # /lava-6963069/bin/lava-test-runner /lava-6963069/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-6963069/1/tests/1_bootrr + cat uuid + UUID=6963069_1.5.2.4.5<8>[ 10.151418] + set +x + export 'PATH=/opt/bootrr/helpers:/lava-6963069/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-6963069/1/../bin/lava-test-case <8>[ 11.221632] /lava-6963069/1/../bin/lava-test-case <8>[ 11.279571] /lava-6963069/1/../bin/lava-test-case <8>[ 11.304717] + set +x <8>[ 11.326567] / #