Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3028 device /dev/ttyimx6qp-sabresd-1 [115200 N81] (Debian GNU/Linux) � U-Boot 2017.03 (Jan 20 2018 - 10:43:25 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 20C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial flash target is MMC:1 Net: Warning: ethernet@02188000 using MAC address from ROM eth0: ethernet@02188000 [PRIME] Fastboot: Normal Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.241 (1329 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x12000000 1027046/tftp-deploy-1qo50mcq/kernel/zImage tftp 0x12000000 1027046/tftp-deploy-1qo50mcq/kernel/zImage Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1027046/tftp-deploy-1qo50mcq/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 9.5 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x12C00000 1027046/tftp-deploy-1qo50mcq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x12C00000 1027046/tftp-deploy-1qo50mcq/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1027046/tftp-deploy-1qo50mcq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x12c00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 9 MiB/s done Bytes transferred = 16056729 (f50199 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 1027046/tftp-deploy-1qo50mcq/dtb/imx6qp-sabresd.dtb tftp 0x18000000 1027046/tftp-deploy-1qo50mcq/dtb/imx6qp-sabresd.dtb Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1027046/tftp-deploy-1qo50mcq/dtb/imx6qp-sabresd.dtb'. Load address: 0x18000000 Loading: *#### 5.3 MiB/s done Bytes transferred = 44727 (aeb7 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x12000000 0x12C00000 0x18000000 bootz 0x12000000 0x12C00000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 12c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16056665 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800deb6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.131-cip13 (KernelCI@build-j448477-arm-gcc-10-multi-v7-defconfig-9k75h) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 3 16:37:45 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad Plus SABRE Smart Device Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933700K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49340K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022550] Console: colour dummy device 80x30 <6>[ 0.024442] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034856] pid_max: default: 32768 minimum: 301 <6>[ 0.039901] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047307] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055940] CPU: Testing write buffer coherency: ok <6>[ 0.060421] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065983] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072330] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080165] rcu: Hierarchical SRCU implementation. <6>[ 0.087245] EFI services will not be available. <6>[ 0.089471] smp: Bringing up secondary CPUs ... <6>[ 0.094771] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094780] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106151] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.106160] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117311] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117319] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127764] smp: Brought up 1 node, 4 CPUs <6>[ 0.131987] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138448] CPU: All CPU(s) started in SVC mode. <6>[ 0.143850] devtmpfs: initialized <6>[ 0.154808] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.160161] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.170019] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.180260] pinctrl core: initialized pinctrl subsystem <6>[ 0.184662] DMI not present or invalid. <6>[ 0.187813] NET: Registered protocol family 16 <6>[ 0.194711] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201376] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201561] cpuidle: using governor menu <6>[ 0.209626] CPU identified as i.MX6QP, silicon rev 1.0 <6>[ 0.385724] vdd3p0: supplied by regulator-dummy <6>[ 0.858123] No ATAGs? <6>[ 0.858301] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.866087] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.876289] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.886811] Serial: AMBA PL011 UART driver <6>[ 0.918453] mxs-dma 110000.dma-apbh: initialized <6>[ 0.927191] iommu: Default domain type: Translated <6>[ 0.929883] vgaarb: loaded <5>[ 0.933314] SCSI subsystem initialized <6>[ 0.937025] usbcore: registered new interface driver usbfs <6>[ 0.942226] usbcore: registered new interface driver hub <6>[ 0.947828] usbcore: registered new device driver usb <6>[ 0.959600] i2c i2c-0: IMX I2C adapter registered <6>[ 0.970747] i2c i2c-1: IMX I2C adapter registered <6>[ 0.974520] i2c i2c-2: IMX I2C adapter registered <6>[ 0.979302] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.983038] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.992471] PTP clock support registered <6>[ 1.000176] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.052757] NET: Registered protocol family 2 <6>[ 2.054874] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.063347] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.070854] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.078869] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.086352] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.093004] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.099706] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.107182] NET: Registered protocol family 1 <6>[ 2.112204] RPC: Registered named UNIX socket transport module. <6>[ 2.117771] RPC: Registered udp transport module. <6>[ 2.122766] RPC: Registered tcp transport module. <6>[ 2.127692] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.134416] PCI: CLS 0 bytes, default 64 <6>[ 2.139089] Trying to unpack rootfs image as initramfs... <6>[ 3.472409] Freeing initrd memory: 15684K <4>[ 3.474355] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.481624] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.491389] Initialise system trusted keyrings <6>[ 3.494556] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.506835] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.510873] NFS: Registering the id_resolver key type <5>[ 3.515420] Key type id_resolver registered <5>[ 3.519821] Key type id_legacy registered <6>[ 3.524214] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.531106] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.538728] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.543791] Key type asymmetric registered <5>[ 3.547662] Asymmetric key parser 'x509' registered <6>[ 3.552866] bounce: pool size: 64 pages <6>[ 3.556914] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.564564] io scheduler mq-deadline registered <6>[ 3.569325] io scheduler kyber registered <4>[ 3.599227] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 3.631526] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.638431] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.699545] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.707716] SuperH (H)SCI(F) driver initialized <6>[ 3.710650] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 33, base_baud = 5000000) is a IMX <6>[ 3.718571] printk: console [ttymxc0] enabled <6>[ 3.718571] printk: console [ttymxc0] enabled <6>[ 3.727766] printk: bootconsole [ec_imx21] disabled <6>[ 3.727766] printk: bootconsole [ec_imx21] disabled <6>[ 3.739620] msm_serial: driver initialized <6>[ 3.745485] STMicroelectronics ASC driver initialized <6>[ 3.752772] STM32 USART driver initialized <4>[ 3.767987] panel-simple panel: supply power not found, using dummy regulator <6>[ 3.784300] brd: module loaded <6>[ 3.796809] loop: module loaded <6>[ 3.804347] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.812599] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.820890] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.829335] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.837354] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.845102] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.852667] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.863247] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.870535] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.879593] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.890270] scsi host0: ahci-imx <6>[ 3.894128] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 85 <6>[ 3.914556] CAN device driver interface <6>[ 3.919953] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.927407] pps pps0: new PPS source ptp0 <6>[ 3.983011] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.990679] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.995909] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.002185] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.007850] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.019738] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.027472] usbcore: registered new interface driver pegasus <6>[ 4.033456] usbcore: registered new interface driver asix <6>[ 4.039149] usbcore: registered new interface driver ax88179_178a <6>[ 4.045566] usbcore: registered new interface driver cdc_ether <6>[ 4.051727] usbcore: registered new interface driver smsc75xx <6>[ 4.057777] usbcore: registered new interface driver smsc95xx <6>[ 4.063836] usbcore: registered new interface driver net1080 <6>[ 4.069788] usbcore: registered new interface driver cdc_subset <6>[ 4.076019] usbcore: registered new interface driver zaurus <6>[ 4.081958] usbcore: registered new interface driver cdc_ncm <6>[ 4.091506] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.098300] ehci-pci: EHCI PCI platform driver <6>[ 4.103067] ehci-platform: EHCI generic platform driver <6>[ 4.108850] ehci-orion: EHCI orion driver <6>[ 4.113376] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.117847] ehci-st: EHCI STMicroelectronics driver <6>[ 4.123224] ehci-exynos: EHCI Exynos driver <6>[ 4.127855] ehci-atmel: EHCI Atmel driver <6>[ 4.132329] tegra-ehci: Tegra EHCI driver <6>[ 4.136819] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.143302] ohci-pci: OHCI PCI platform driver <6>[ 4.148054] ohci-platform: OHCI generic platform driver <6>[ 4.153820] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.158280] ohci-st: OHCI STMicroelectronics driver <6>[ 4.163632] ohci-atmel: OHCI Atmel driver <6>[ 4.168973] usbcore: registered new interface driver usb-storage <6>[ 4.183436] i2c /dev entries driver <6>[ 4.207490] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.213981] sdhci: Copyright(c) Pierre Ossman <6>[ 4.221385] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.229604] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.231702] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.236884] sdhci-esdhc-imx 2194000.mmc: Got CD GPIO <6>[ 4.241266] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.246474] sdhci-esdhc-imx 2194000.mmc: Got WP GPIO <6>[ 4.250932] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.250967] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.252996] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.276291] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.280351] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.283719] usbcore: registered new interface driver usbhid <6>[ 4.290038] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.295555] usbhid: USB HID core driver <4>[ 4.299764] isl29018 2-0044: No cache defaults, reading back from HW <6>[ 4.307655] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <3>[ 4.314138] isl29018 2-0044: Failed to read 1: -6 <3>[ 4.325616] isl29018 2-0044: regmap initialization fails: -6 <6>[ 4.334647] NET: Registered protocol family 10 <6>[ 4.340613] Segment Routing with IPv6 <6>[ 4.344613] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.351406] NET: Registered protocol family 17 <6>[ 4.355405] mmc2: new high speed SDHC card at address aaaa <6>[ 4.356126] can: controller area network core <6>[ 4.362833] mmcblk2: mmc2:aaaa SS08G 7.40 GiB <6>[ 4.366597] NET: Registered protocol family 29 <6>[ 4.373260] mmc3: new DDR MMC card at address 0001 <6>[ 4.375972] can: raw protocol <6>[ 4.382147] mmcblk3: mmc3:0001 Q2J55L 7.13 GiB <6>[ 4.384284] can: broadcast manager protocol <6>[ 4.389599] mmcblk3boot0: mmc3:0001 Q2J55L partition 1 2.00 MiB <6>[ 4.393568] can: netlink gateway - max_hops=1 <6>[ 4.400501] mmcblk3boot1: mmc3:0001 Q2J55L partition 2 2.00 MiB <5>[ 4.404909] Key type dns_resolver registered <6>[ 4.410986] mmcblk3rpmb: mmc3:0001 Q2J55L partition 3 4.00 MiB, chardev (235:0) <6>[ 4.424119] ThumbEE CPU extension supported. <5>[ 4.428707] Registering SWP/SWPB emulation handler <5>[ 4.434057] Loading compiled-in X.509 certificates <4>[ 4.472244] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.484054] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.495754] imx_usb 2184200.usb: No over current polarity defined <4>[ 4.511793] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.523620] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.535343] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.545364] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.560535] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.572379] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.584044] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.671134] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:01: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 7.840524] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.860185] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.890244] Sending DHCP requests .., OK <6>[ 10.354386] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.241 <6>[ 10.362254] IP-Config: Complete: <6>[ 10.365753] device=eth0, hwaddr=00:04:9f:05:b8:c3, ipaddr=172.16.1.241, mask=255.255.255.0, gw=172.16.1.4 <6>[ 10.376037] host=172.16.1.241, domain=example.org, nis-domain=(none) <6>[ 10.383106] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.383112] nameserver0=172.16.1.4 <6>[ 10.398238] Freeing unused kernel memory: 2048K <6>[ 10.430627] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.562242] udevd[129]: starting version 3.2.9 <5>[ 10.567989] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.575076] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.581967] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 10.597619] udevd[129]: specified user 'tss' unknown <27>[ 10.603276] udevd[129]: specified group 'tss' unknown <30>[ 10.611727] udevd[130]: starting eudev-3.2.9 <6>[ 11.085395] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 11.100611] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 11.113401] panel-simple panel: supply power not found, using dummy regulator <6>[ 11.122560] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 11.125260] etnaviv-gpu 130000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.135141] etnaviv-gpu: probe of 130000.gpu failed with error -110 <4>[ 11.141857] etnaviv-gpu 134000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.146610] imx_usb 2184200.usb: No over current polarity defined <4>[ 11.149457] etnaviv-gpu: probe of 134000.gpu failed with error -110 <4>[ 11.162708] etnaviv-gpu 2204000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.166772] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 11.170425] etnaviv-gpu: probe of 2204000.gpu failed with error -110 <6>[ 11.204298] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.212968] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.221714] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.230372] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.239085] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.245859] caam 2100000.crypto: Entropy delay = 3200 <6>[ 11.251194] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops [dw_hdmi_imx]) <4>[ 11.274818] panel-simple panel: supply power not found, using dummy regulator <6>[ 11.314720] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 11.360075] imx_usb 2184200.usb: No over current polarity defined <6>[ 11.375480] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 11.380941] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 11.387829] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 11.399259] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.407851] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.416596] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.425220] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.434044] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.552292] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <4>[ 11.567716] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 11.603497] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.616104] imx_usb 2184200.usb: No over current polarity defined <6>[ 11.733151] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.741757] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.750385] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.758958] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.767627] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.835619] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <4>[ 11.863546] ------------[ cut here ]------------ <4>[ 11.868530] WARNING: CPU: 3 PID: 78 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <4>[ 11.878002] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 11.878091] Modules linked in: phy_generic(+) caam error dw_hdmi_imx dw_hdmi imx_ldb imxdrm etnaviv gpu_sched imx_ipu_v3 <4>[ 11.886167] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 11.897190] CPU: 3 PID: 78 Comm: kworker/3:3 Not tainted 5.10.131-cip13 #1 <4>[ 11.905892] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 11.912756] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 11.912790] Workqueue: events deferred_probe_work_func <4>[ 11.922668] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 11.927536] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) <4>[ 11.949363] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 11.956861] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 11.964109] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) <4>[ 11.971872] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <4>[ 11.980763] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 11.990262] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 11.999667] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 12.008039] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) <4>[ 12.016668] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 12.026332] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 12.035389] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 12.044014] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 12.052466] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) <4>[ 12.060915] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 12.069711] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 12.078245] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 12.086695] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 12.095930] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 12.105335] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) <4>[ 12.113700] [] (worker_thread) from [] (kthread+0x14c/0x150) <4>[ 12.121369] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 12.128855] Exception stack(0xc3349fb0 to 0xc3349ff8) <4>[ 12.134174] 9fa0: 00000000 00000000 00000000 00000000 <4>[ 12.142618] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 12.151061] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 12.158040] ---[ end trace 420adcf947bd17fa ]--- <4>[ 12.164415] pwm-backlight backlig# ht-lvds: supply power not found, using dummy regulator <4>[ 12.178333] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.192065] imx_usb 2184200.usb: No over current polarity defined <6>[ 12.216581] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) #<6>[ 12.225280] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 12.233984] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.242576] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 12.251391] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 12.262463] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <4>[ 12.273811] ------------[ cut here ]------------ <4>[ 12.278741] WARNING: CPU: 3 PID: 78 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <4>[ 12.288325] Modules linked in: authenc phy_generic caam error dw_hdmi_imx dw_hdmi imx_ldb imxdrm etnaviv gpu_sched imx_ipu_v3 <4>[ 12.300173] CPU: 3 PID: 78 Comm: kworker/3:3 Tainted: G W 5.10.131-cip13 #1 <4>[ 12.308716] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 12.315539] Workqueue: events deferred_probe_work_func <4>[ 12.320975] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) <4>[ 12.328995] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 12.336492] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 12.343735] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) <4>[ 12.351496] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <4>[ 12.360383] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 12.369877] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 12.379283] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 12.387654] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) <4>[ 12.396282] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 12.405947] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 12.415002] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 12.423626] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 12.432074] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) <4>[ 12.440522] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 12.449316] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 12.457849] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 12.466296] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 12.475529] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 12.484932] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) <4>[ 12.493294] [] (worker_thread) from [] (kthread+0x14c/0x150) <4>[ 12.500963] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 12.508448] Exception stack(0xc3349fb0 to 0xc3349ff8) <4>[ 12.513767] 9fa0: 00000000 00000000 00000000 00000000 <4>[ 12.522211] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 12.530655] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 12.537611] ---[ end trace 420adcf947bd17fb ]--- <6>[ 12.549650] caam algorithms registered in /proc/crypto <6>[ 12.557995] caam 2100000.crypto: registering rng-caam <4>[ 12.565532] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 12.581928] panel-simple panel: supply power not # found, using dummy regulator <4>[ 12.595680] imx_usb 2184200.usb: No over current polarity defined <6>[ 12.614491] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.623046] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) done <6>[ 12.631694] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.640595] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) #<6>[ 12.649251] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 12.661709] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) Saving random seed: <5>[ 12.685443] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL <5>[ 12.745922] random: crng init done <5>[ 12.749603] random: 1 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # # / # # # / # / # #export SHELL=/bin/sh . /lava-1027046/environment / # export SHELL=/bin/sh / # . /lava-1027046/environment / # /lava-1027046/bin/lava-test-runner /lava-1027046/0 /lava-1027046/bin/lava-test-runner /lava-1027046/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1027046/0/tests/0_dmesg + cat uuid + UUID=1027046_1.5.2.4<8>[ 18.585131] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.633405] <8>[ 18.676196] <8>[ 18.719749] + set<8>[ 18.729679] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1027046/environment / # . /lava-1027046/environment/lava-1027046/bin/lava-test-runner /lava-1027046/1 / # /lava-1027046/bin/lava-test-runner /lava-1027046/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1027046/1/tests/1_bootrr + cat uuid + UUID=1027046_1.5.2<8>[ 24.458372] .4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1027046/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1027046/1/../bin/lava-test-case <8>[ 25.506762] /lava-1027046/1/../bin/lava-test-case <8>[ 25.547998] /lava-1027046/1/../bin/lava-test-case <8>[ 25.573429] + set<8>[ 25.593100] +x / #