Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3028 device /dev/ttyimx6qp-sabresd-1 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03 (Jan 20 2018 - 10:43:25 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 20C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial flash target is MMC:1 Net: Warning: ethernet@02188000 using MAC address from ROM eth0: ethernet@02188000 [PRIME] Fastboot: Normal Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.241 (1677 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x12000000 1029249/tftp-deploy-6qlhjmeb/kernel/zImage tftp 0x12000000 1029249/tftp-deploy-6qlhjmeb/kernel/zImage Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1029249/tftp-deploy-6qlhjmeb/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 9.5 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x12C00000 1029249/tftp-deploy-6qlhjmeb/ramdisk/ramdisk.cpio.gz.uboot tftp 0x12C00000 1029249/tftp-deploy-6qlhjmeb/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1029249/tftp-deploy-6qlhjmeb/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x12c00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 10 MiB/s done Bytes transferred = 16051394 (f4ecc2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 1029249/tftp-deploy-6qlhjmeb/dtb/imx6qp-sabresd.dtb tftp 0x18000000 1029249/tftp-deploy-6qlhjmeb/dtb/imx6qp-sabresd.dtb Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1029249/tftp-deploy-6qlhjmeb/dtb/imx6qp-sabresd.dtb'. Load address: 0x18000000 Loading: *#### 8.5 MiB/s done Bytes transferred = 44727 (aeb7 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x12000000 0x12C00000 0x18000000 bootz 0x12000000 0x12C00000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 12c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16051330 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800deb6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.131-cip13 (KernelCI@build-j458595-arm-gcc-10-multi-v7-defconfig-9s8dr) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Aug 5 01:39:53 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad Plus SABRE Smart Device Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933708K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49332K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022551] Console: colour dummy device 80x30 <6>[ 0.024442] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034856] pid_max: default: 32768 minimum: 301 <6>[ 0.039898] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047308] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055940] CPU: Testing write buffer coherency: ok <6>[ 0.060421] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065982] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072318] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080147] rcu: Hierarchical SRCU implementation. <6>[ 0.087258] EFI services will not be available. <6>[ 0.089496] smp: Bringing up secondary CPUs ... <6>[ 0.094782] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094791] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106165] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.106174] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117313] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117321] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127779] smp: Brought up 1 node, 4 CPUs <6>[ 0.132002] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138457] CPU: All CPU(s) started in SVC mode. <6>[ 0.143862] devtmpfs: initialized <6>[ 0.154801] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.160150] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.170011] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.180246] pinctrl core: initialized pinctrl subsystem <6>[ 0.184658] DMI not present or invalid. <6>[ 0.187801] NET: Registered protocol family 16 <6>[ 0.194699] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201374] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201557] cpuidle: using governor menu <6>[ 0.209614] CPU identified as i.MX6QP, silicon rev 1.0 <6>[ 0.385709] vdd3p0: supplied by regulator-dummy <6>[ 0.858303] No ATAGs? <6>[ 0.858485] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.866267] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.876499] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.887034] Serial: AMBA PL011 UART driver <6>[ 0.918665] mxs-dma 110000.dma-apbh: initialized <6>[ 0.927409] iommu: Default domain type: Translated <6>[ 0.930151] vgaarb: loaded <5>[ 0.933513] SCSI subsystem initialized <6>[ 0.937215] usbcore: registered new interface driver usbfs <6>[ 0.942448] usbcore: registered new interface driver hub <6>[ 0.948029] usbcore: registered new device driver usb <6>[ 0.959805] i2c i2c-0: IMX I2C adapter registered <6>[ 0.970942] i2c i2c-1: IMX I2C adapter registered <6>[ 0.974708] i2c i2c-2: IMX I2C adapter registered <6>[ 0.979502] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.983232] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.992663] PTP clock support registered <6>[ 1.000350] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.052377] NET: Registered protocol family 2 <6>[ 2.054492] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.062961] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.070471] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.078491] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.085959] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.092628] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.099326] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.106800] NET: Registered protocol family 1 <6>[ 2.111883] RPC: Registered named UNIX socket transport module. <6>[ 2.117392] RPC: Registered udp transport module. <6>[ 2.122386] RPC: Registered tcp transport module. <6>[ 2.127311] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.134035] PCI: CLS 0 bytes, default 64 <6>[ 2.138686] Trying to unpack rootfs image as initramfs... <6>[ 3.474423] Freeing initrd memory: 15676K <4>[ 3.476371] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.483623] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.493399] Initialise system trusted keyrings <6>[ 3.496584] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.508958] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.512931] NFS: Registering the id_resolver key type <5>[ 3.517540] Key type id_resolver registered <5>[ 3.521969] Key type id_legacy registered <6>[ 3.526298] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.533188] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.540876] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.545894] Key type asymmetric registered <5>[ 3.549786] Asymmetric key parser 'x509' registered <6>[ 3.554990] bounce: pool size: 64 pages <6>[ 3.559037] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.566686] io scheduler mq-deadline registered <6>[ 3.571465] io scheduler kyber registered <4>[ 3.601431] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 3.633432] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.640388] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.684936] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.693101] SuperH (H)SCI(F) driver initialized <6>[ 3.696012] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 33, base_baud = 5000000) is a IMX <6>[ 3.703982] printk: console [ttymxc0] enabled <6>[ 3.703982] printk: console [ttymxc0] enabled <6>[ 3.713146] printk: bootconsole [ec_imx21] disabled <6>[ 3.713146] printk: bootconsole [ec_imx21] disabled <6>[ 3.724972] msm_serial: driver initialized <6>[ 3.730880] STMicroelectronics ASC driver initialized <6>[ 3.738134] STM32 USART driver initialized <4>[ 3.753527] panel-simple panel: supply power not found, using dummy regulator <6>[ 3.769847] brd: module loaded <6>[ 3.782526] loop: module loaded <6>[ 3.789971] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.798211] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.806506] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.814969] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.822990] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.830731] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.838298] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.848900] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.856183] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.865260] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.875959] scsi host0: ahci-imx <6>[ 3.879820] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 85 <6>[ 3.900311] CAN device driver interface <6>[ 3.905720] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.913164] pps pps0: new PPS source ptp0 <6>[ 3.968660] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.976268] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.981522] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.987768] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.993449] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.005349] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.013075] usbcore: registered new interface driver pegasus <6>[ 4.019039] usbcore: registered new interface driver asix <6>[ 4.024760] usbcore: registered new interface driver ax88179_178a <6>[ 4.031170] usbcore: registered new interface driver cdc_ether <6>[ 4.037309] usbcore: registered new interface driver smsc75xx <6>[ 4.043379] usbcore: registered new interface driver smsc95xx <6>[ 4.049420] usbcore: registered new interface driver net1080 <6>[ 4.055391] usbcore: registered new interface driver cdc_subset <6>[ 4.061629] usbcore: registered new interface driver zaurus <6>[ 4.067536] usbcore: registered new interface driver cdc_ncm <6>[ 4.077018] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.083834] ehci-pci: EHCI PCI platform driver <6>[ 4.088581] ehci-platform: EHCI generic platform driver <6>[ 4.094382] ehci-orion: EHCI orion driver <6>[ 4.098879] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.103369] ehci-st: EHCI STMicroelectronics driver <6>[ 4.108699] ehci-exynos: EHCI Exynos driver <6>[ 4.113358] ehci-atmel: EHCI Atmel driver <6>[ 4.117811] tegra-ehci: Tegra EHCI driver <6>[ 4.122337] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.128801] ohci-pci: OHCI PCI platform driver <6>[ 4.133573] ohci-platform: OHCI generic platform driver <6>[ 4.139316] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.143798] ohci-st: OHCI STMicroelectronics driver <6>[ 4.149123] ohci-atmel: OHCI Atmel driver <6>[ 4.154477] usbcore: registered new interface driver usb-storage <6>[ 4.168889] i2c /dev entries driver <6>[ 4.192559] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.199008] sdhci: Copyright(c) Pierre Ossman <6>[ 4.206306] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.214517] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.221777] sdhci-esdhc-imx 2194000.mmc: Got CD GPIO <6>[ 4.221904] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.226649] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.226679] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.227046] sdhci-esdhc-imx 2194000.mmc: Got WP GPIO <6>[ 4.232768] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.254953] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.258517] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.258977] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.270563] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <6>[ 4.284052] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.291579] usbcore: registered new interface driver usbhid <6>[ 4.297436] usbhid: USB HID core driver <4>[ 4.305800] isl29018 2-0044: No cache defaults, reading back from HW <3>[ 4.313120] isl29018 2-0044: Failed to read 1: -6 <3>[ 4.318114] isl29018 2-0044: regmap initialization fails: -6 <6>[ 4.327200] NET: Registered protocol family 10 <6>[ 4.333032] Segment Routing with IPv6 <6>[ 4.337040] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.342579] mmc3: new DDR MMC card at address 0001 <6>[ 4.343840] NET: Registered protocol family 17 <6>[ 4.349126] mmcblk3: mmc3:0001 Q2J55L 7.13 GiB <6>[ 4.353037] can: controller area network core <6>[ 4.358329] mmcblk3boot0: mmc3:0001 Q2J55L partition 1 2.00 MiB <6>[ 4.362551] NET: Registered protocol family 29 <6>[ 4.369160] mmcblk3boot1: mmc3:0001 Q2J55L partition 2 2.00 MiB <6>[ 4.373387] can: raw protocol <6>[ 4.382819] can: broadcast manager protocol <6>[ 4.382956] mmcblk3rpmb: mmc3:0001 Q2J55L partition 3 4.00 MiB, chardev (235:0) <6>[ 4.387279] can: netlink gateway - max_hops=1 <5>[ 4.400212] Key type dns_resolver registered <6>[ 4.405952] ThumbEE CPU extension supported. <5>[ 4.410539] Registering SWP/SWPB emulation handler <5>[ 4.415884] Loading compiled-in X.509 certificates <6>[ 4.430368] mmc2: new high speed SDHC card at address aaaa <6>[ 4.437307] mmcblk2: mmc2:aaaa SS08G 7.40 GiB <4>[ 4.452868] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.464842] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.476576] imx_usb 2184200.usb: No over current polarity defined <4>[ 4.492546] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.504407] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.516136] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.532754] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.541849] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.553943] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.565680] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.661313] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:01: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 7.760703] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.768490] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.790340] Sending DHCP requests .., OK <6>[ 10.794562] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.241 <6>[ 10.802418] IP-Config: Complete: <6>[ 10.805917] device=eth0, hwaddr=00:04:9f:05:b8:c3, ipaddr=172.16.1.241, mask=255.255.255.0, gw=172.16.1.4 <6>[ 10.816194] host=172.16.1.241, domain=example.org, nis-domain=(none) <6>[ 10.823258] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.823264] nameserver0=172.16.1.4 <6>[ 10.838394] Freeing unused kernel memory: 2048K <6>[ 10.870810] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.998472] udevd[129]: starting version 3.2.9 <5>[ 11.004333] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.011530] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.018356] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 11.033958] udevd[129]: specified user 'tss' unknown <27>[ 11.039417] udevd[129]: specified group 'tss' unknown <30>[ 11.047824] udevd[130]: starting eudev-3.2.9 <6>[ 11.462685] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 11.470287] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 11.476402] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 11.524607] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.542990] etnaviv-gpu 130000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.550658] etnaviv-gpu: probe of 130000.gpu failed with error -110 <4>[ 11.555633] imx_usb 2184200.usb: No over current polarity defined <4>[ 11.557247] etnaviv-gpu 134000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.571252] etnaviv-gpu: probe of 134000.gpu failed with error -110 <4>[ 11.574174] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 11.577981] etnaviv-gpu 2204000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.593811] etnaviv-gpu: probe of 2204000.gpu failed with error -110 <6>[ 11.690924] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.699543] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.708394] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 11.714376] panel-simple panel: supply power not found, using dummy regulator <6>[ 11.717052] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.733005] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <4>[ 11.757234] imx_usb 2184200.usb: No over current polarity defined <4>[ 11.774612] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 11.784622] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops [dw_hdmi_imx]) <4>[ 11.884782] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.916670] imx_usb 2184200.usb: No over current polarity defined <6>[ 11.946872] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.955492] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.964185] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.972759] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.981548] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.992774] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <6>[ 12.003869] caam 2100000.crypto: Entropy delay = 3200 <6>[ 12.069986] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 12.130750] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 12.136201] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 12.143154] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 12.153024] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 12.184200] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.197246] imx_usb 2184200.usb: No over current polarity defined <6>[ 12.219925] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.228568] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 12.237272] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.245933] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 12.254711] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 12.268331] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <4>[ 12.281877] ------------[ cut here ]------------ <4>[ 12.286838] WARNING: CPU: 0 PID: 59 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <4>[ 12.296396] Modules linked in: caam error dw_hdmi_imx dw_hdmi etnaviv gpu_sched imx_ldb imxdrm imx_ipu_v3 <4>[ 12.306364] CPU: 0 PID: 59 Comm: kworker/0:8 Not tainted 5.10.131-cip13 #1 <4>[ 12.310235] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 12.313520] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 12.313559] Workqueue: events deferred_probe_work_func <4>[ 12.313615] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) <4>[ 12.313634] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 12.313656] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 12.326551] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 12.328412] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) <4>[ 12.328443] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <4>[ 12.334154] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 12.341853] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 12.341876] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 12.341897] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 12.352257] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 12.356617] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) <4>[ 12.356643] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 12.443508] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 12.452567] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 12.461197] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 12.469649] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) <4>[ 12.478100] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 12.486895] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 12.495428] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 12.503876] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 12.513116] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 12.522521] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) <4>[ 12.530887] [] (worker_thread) from [] (kthread+0x14c/0x150) <4>[ 12.538556] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 12.546043] Exception stack(0xc2463fb0 to 0xc2463ff8) <4>[ 12.551362] 3fa0: 00000000 00000000 00000000 00000000 <4>[ 12.559806] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 12.568250] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 12.575185] ---[ end trace bade9346a9626107 ]---# <4>[ 12.585454] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 12.602209] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.626683] imx_usb 2184200.usb: No over current polarity defined <6>[ 12.652441] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.661155] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 12.669774] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) #<6>[ 12.678464] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 12.687159] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 12.698785] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <4>[ 12.710399] ------------[ cut here ]------------ <4>[ 12.715399] WARNING: CPU: 0 PID: 59 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <4>[ 12.725011] Modules linked in: caam_jr(+) caamhash_desc caamalg_desc crypto_engine libdes authenc phy_generic caam error dw_hdmi_imx dw_hdmi etnaviv gpu_sched imx_ldb imxdrm imx_ipu_v3 <4>[ 12.741838] CPU: 0 PID: 59 Comm: kworker/0:8 Tainted: G W 5.10.131-cip13 #1 <4>[ 12.750368] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 12.757178] Workqueue: events deferred_probe_work_func <4>[ 12.762606] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) <4>[ 12.770623] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 12.778118] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 12.785360] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) <4>[ 12.793122] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <4>[ 12.802007] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 12.811502] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 12.820907] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 12.829280] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) <4>[ 12.837908] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 12.847572] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 12.856628] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 12.865252] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 12.873700] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) <4>[ 12.882147] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 12.890942] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 12.899475] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 12.907922] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 12.917156] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 12.926558] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) <4>[ 12.934921] [] (worker_thread) from [] (kthread+0x14c/0x150) <4>[ 12.942588] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 12.950075] Exception stack(0xc2463fb0 to 0xc2463ff8) <4>[ 12.955393] 3fa0: 00000000 00000000 00000000 00000000 <4>[ 12.963838] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 12.972282] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 12.979211] ---[ end trace bade9346a9626108 ]--- <6>[ 12.993444] caam algorithms registered in /proc/crypto <6>[ 13.000699] caam 2100000.crypto: registering rng-caam <4>[ 13.008075] pwm-backlight backlight-lvds: supply power not found, using dummy regulat# or <4>[ 13.024615] panel-simple panel: supply power not found, using dummy regulator <4>[ 13.038062] imx_usb 2184200.usb: No over current polarity defined <6>[ 13.058461] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 13.067084] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) #<6>[ 13.075692] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 13.084235] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) done <6>[ 13.092959] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 13.104907] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) Saving random seed: <4>[ 13.116533] ------------[ cut here ]------------ <4>[ 13.122021] WARNING: CPU: 1 PID: 97 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <5>[ 13.127734] random: dd: uninitialized urandom read (32 bytes read) <4>[ 13.131558] Modules linked in: caam_jr caamhash_desc caamalg_desc crypto_engine libdes authenc phy_generic caam error dw_hdmi_imx dw_hdmi etnaviv gpu_sched imx_ldb imxdrm imx_ipu_v3 OK <4>[ 13.154578] CPU: 1 PID: 97 Comm: kworker/1:5 Tainted: G W 5.10.131-cip13 #1 <4>[ 13.163630] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Starting network: <4>[ 13.170460] Workqueue: events deferred_probe_work_func <4>[ 13.177442] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) <4>[ 13.185480] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <5>[ 13.188546] random: crng init done <4>[ 13.192994] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 13.193016] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) ip: RTNETLINK answers: File exist<4>[ 13.193040] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <5>[ 13.196692] random: 1 urandom warning(s) missed due to ratelimiting s <4>[ 13.203920] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 13.203942] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) FAIL<4>[ 13.249091] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 13.257802] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) <4>[ 13.266607] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 13.276309] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) Starting dropbear sshd: <4>[ 13.285391] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 13.296076] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 13.304561] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) OK <4>[ 13.313049] [] (driver_probe_device) from [] (bus_for_each_drv+0x84/0xc8) <4>[ 13.322209] [] (bus_for_each_drv) from [] (__device_attach+0xb0/0x1d8) <4>[ 13.330775] [] (__device_attach) from [] (bus_probe_device+0x84/0x8c) <4>[ 13.339228] [] (bus_probe_device) from [] (deferred_probe_work_func+0x78/0xa4) <4>[ 13.348464] [] (deferred_probe_work_func) from [] (process_one_work+0x1ec/0x548) <4>[ 13.357867] [] (process_one_work) from [] (worker_thread+0x64/0x5a8) <4>[ 13.366231] [] (worker_thread) from [] (kthread+0x14c/0x150) <4>[ 13.373902] [] (kthread) from [] (ret_from_fork+0x14/0x2c) <4>[ 13.381388] Exception stack(0xc3787fb0 to 0xc3787ff8) <4>[ 13.386705] 7fa0: 00000000 00000000 00000000 00000000 <4>[ 13.395152] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 13.403594] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 13.410554] ---[ end trace bade9346a9626109 ]--- <4>[ 13.416824] pwm-backlight ba# cklight-lvds: supply power not found, using dummy regulator /bin/sh: can't access tty; job control turned off / # # / # # / # <4>[ 13.430059] panel-simple panel: supply power not found, using dummy regulator # # export SHELL=/bin/sh / # / # # / # export SHELL=/bin/sh. /lava-1029249/environment /lava-1029249/bin/lava-test-runner /lava-1029249/0 / # . /lava-1029249/environment / # /lava-1029249/bin/lava-test-runner /lava-1029249/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1029249/0/tests/0_dmesg + cat uuid + UUID=1029249_1.5.2.4<8>[ 19.300442] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.349179] <8>[ 19.392941] <8>[ 19.436517] + set<8>[ 19.446463] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1029249/environment / # . /lava-1029249/environment/lava-1029249/bin/lava-test-runner /lava-1029249/1 / # /lava-1029249/bin/lava-test-runner /lava-1029249/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1029249/1/tests/1_bootrr + cat uuid + UUID=1029249_1.5.2<8>[ 25.167711] .4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1029249/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1029249/1/../bin/lava-test-case <8>[ 26.215674] /lava-1029249/1/../bin/lava-test-case <8>[ 26.256658] /lava-1029249/1/../bin/lava-test-case <8>[ 26.282569] + set<8>[ 26.302174] +x / #