Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.98 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 155981/tftp-deploy-cmlomct4/kernel/Image tftp 0x82000000 155981/tftp-deploy-cmlomct4/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.98; sending through gateway 172.16.0.254 Filename '155981/tftp-deploy-cmlomct4/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 13.1 MiB/s done Bytes transferred = 31836672 (1e5ca00 hex) => tftp 0x90080000 155981/tftp-deploy-cmlomct4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 155981/tftp-deploy-cmlomct4/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.98; sending through gateway 172.16.0.254 Filename '155981/tftp-deploy-cmlomct4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### 12.2 MiB/s done Bytes transferred = 15333002 (e9f68a hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 155981/tftp-deploy-cmlomct4/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 155981/tftp-deploy-cmlomct4/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.98; sending through gateway 172.16.0.254 Filename '155981/tftp-deploy-cmlomct4/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 6 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/155981/extract-nfsrootfs-7j4t5dcf,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/155981/extract-nfsrootfs-7j4t5dcf,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2022-08-17 10:58:53 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15332938 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.131-cip13 (KernelCI@build-j56228-arm64-gcc-10-defconfig-9f5sp) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Wed Aug 17 10:36:02 UTC 2022 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7feb00-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 23 pages/cpu s56600 r8192 d29416 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/155981/extract-nfsrootfs-7j4t5dcf,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3901252K/4126720K available (14592K kernel code, 2802K rwdata, 7596K rodata, 5952K init, 512K bss, 192700K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008694] Console: colour dummy device 80x25 <6>[ 0.013483] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024201] pid_max: default: 32768 minimum: 301 <6>[ 0.029161] LSM: Security Framework initializing <6>[ 0.034129] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041884] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050949] rcu: Hierarchical SRCU implementation. <6>[ 0.056199] Platform MSI: gic-its@6020000 domain created <6>[ 0.061904] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069763] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075825] EFI services will not be available. <6>[ 0.080768] smp: Bringing up secondary CPUs ... <6>[ 0.085871] Detected PIPT I-cache on CPU1 <6>[ 0.085889] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.085897] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.085923] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.085978] smp: Brought up 1 node, 2 CPUs <6>[ 0.116291] SMP: Total of 2 processors activated. <6>[ 0.121303] CPU features: detected: 32-bit EL0 Support <6>[ 0.126761] CPU features: detected: CRC32 instructions <6>[ 0.132212] CPU features: detected: 32-bit EL1 Support <6>[ 0.148613] CPU: All CPU(s) started at EL2 <6>[ 0.153031] alternatives: patching kernel code <6>[ 0.158523] devtmpfs: initialized <4>[ 0.164196] KASLR disabled due to lack of seed <6>[ 0.169051] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.179159] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.186837] pinctrl core: initialized pinctrl subsystem <6>[ 0.192985] DMI not present or invalid. <6>[ 0.197511] NET: Registered protocol family 16 <6>[ 0.203019] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210513] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218758] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.227035] audit: initializing netlink subsys (disabled) <5>[ 0.232871] audit: type=2000 audit(0.148:1): state=initialized audit_enabled=0 res=1 <6>[ 0.233378] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.240959] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.247506] cpuidle: using governor menu <6>[ 0.258682] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.265824] ASID allocator initialised with 65536 entries <6>[ 0.272186] Serial: AMBA PL011 UART driver <6>[ 0.287175] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.294825] SoC family: QorIQ LS1028A <6>[ 0.298778] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.311242] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.318282] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.325311] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.332341] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.340127] cryptd: max_cpu_qlen set to 1000 <6>[ 0.346072] ACPI: Interpreter disabled. <6>[ 0.351137] iommu: Default domain type: Translated <6>[ 0.356439] vgaarb: loaded <5>[ 0.359573] SCSI subsystem initialized <6>[ 0.363843] usbcore: registered new interface driver usbfs <6>[ 0.369674] usbcore: registered new interface driver hub <6>[ 0.375316] usbcore: registered new device driver usb <6>[ 0.380922] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.388869] i2c i2c-0: IMX I2C adapter registered <6>[ 0.394052] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.401740] i2c i2c-1: IMX I2C adapter registered <6>[ 0.406851] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.414625] i2c i2c-2: IMX I2C adapter registered <6>[ 0.419911] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.425187] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.434687] PTP clock support registered <6>[ 0.438974] EDAC MC: Ver: 3.0.0 <6>[ 0.443140] FPGA manager framework <6>[ 0.446870] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.453698] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.460217] VFS: Disk quotas dquot_6.6.0 <6>[ 0.464469] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.471767] pnp: PnP ACPI: disabled <6>[ 0.478853] NET: Registered protocol family 2 <6>[ 0.483811] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.492872] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.501797] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.510144] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.518152] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.525120] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.532172] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.539728] NET: Registered protocol family 1 <6>[ 0.544687] RPC: Registered named UNIX socket transport module. <6>[ 0.550936] RPC: Registered udp transport module. <6>[ 0.555959] RPC: Registered tcp transport module. <6>[ 0.560970] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.567740] PCI: CLS 0 bytes, default 64 <6>[ 0.572052] Unpacking initramfs... <6>[ 1.082402] Freeing initrd memory: 14968K <6>[ 1.087028] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.095722] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.100904] kvm [1]: GICv3: no GICV resource entry <6>[ 1.106008] kvm [1]: disabling GICv2 emulation <6>[ 1.110772] kvm [1]: GIC system register CPU interface enabled <6>[ 1.116954] kvm [1]: vgic interrupt IRQ9 <6>[ 1.121240] kvm [1]: Hyp mode initialized successfully <5>[ 1.127700] Initialise system trusted keyrings <6>[ 1.132541] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.142444] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.149008] NFS: Registering the id_resolver key type <5>[ 1.154392] Key type id_resolver registered <5>[ 1.158878] Key type id_legacy registered <6>[ 1.163229] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.170259] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.178086] 9p: Installing v9fs 9p2000 file system support <5>[ 1.213660] Key type asymmetric registered <5>[ 1.218065] Asymmetric key parser 'x509' registered <6>[ 1.223270] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.231002] io scheduler mq-deadline registered <6>[ 1.235837] io scheduler kyber registered <6>[ 1.244953] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.253065] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 1.262216] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 1.271364] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 1.280509] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 1.289653] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 1.298798] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 1.307938] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 1.317126] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.326240] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.333535] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.339073] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 1.349789] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 1.360944] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.371665] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.382824] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.393542] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.404696] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 1.415428] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.421787] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.432594] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.443841] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.454909] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.466429] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.472238] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.482515] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.493388] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.499739] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.510548] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.521792] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.532859] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.544379] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.550187] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.560464] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.571301] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.577655] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.588460] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.599714] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.605629] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.611983] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.622788] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.634044] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.639959] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.646311] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.657116] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.668369] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.674285] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.680636] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.691441] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.702687] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.713502] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.719420] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.725771] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.736575] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.747828] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.754404] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.760771] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.769105] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.776774] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.785657] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.794623] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.801657] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.807458] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.813963] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.824870] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.831255] pci 0001:00:00.0: supports D1 D2 <6>[ 1.835829] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.843503] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.850454] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.855883] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 1.863546] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 1.872428] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 1.881382] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 1.888415] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 1.894222] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 1.903535] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.914440] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.920819] pci 0002:00:00.0: supports D1 D2 <6>[ 1.925392] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.933045] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.939994] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 1.946001] EINJ: ACPI disabled. <6>[ 1.957072] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.964956] printk: console [ttyS0] disabled <6>[ 1.969581] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.978742] printk: console [ttyS0] enabled <6>[ 1.978742] printk: console [ttyS0] enabled <6>[ 1.987684] printk: bootconsole [ns16550a0] disabled <6>[ 1.987684] printk: bootconsole [ns16550a0] disabled <6>[ 1.998530] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.007901] SuperH (H)SCI(F) driver initialized <6>[ 2.012998] msm_serial: driver initialized <6>[ 2.017736] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 2.028263] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.034997] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.039896] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.045489] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.051081] arm-smmu 5000000.iommu: nested translation <5>[ 2.056587] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.064014] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.070830] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.077560] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.084287] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 2.095539] loop: module loaded <6>[ 2.103861] megasas: 07.714.04.00-rc1 <6>[ 2.109890] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.121469] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.130535] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.137630] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 2.143139] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.150066] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 2.158045] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 2.166049] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 2.174053] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 2.182040] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.190035] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.198043] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.207744] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.213529] thunder_xcv, ver 1.0 <6>[ 2.217054] thunder_bgx, ver 1.0 <6>[ 2.220575] nicpf, ver 1.0 <6>[ 2.224048] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.337717] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 2.344233] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 12:48:3f:74:08:99 <6>[ 2.353059] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 06:3f:64:2c:fa:44 <6>[ 2.368540] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.481711] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.489100] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.495473] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.605713] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.612520] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.618883] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.729712] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.736514] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.742938] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 2.853712] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 2.860886] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 2.867176] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 2.874096] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 2.883103] pps pps0: new PPS source ptp0 <6>[ 2.887834] hclge is initializing <6>[ 2.891439] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.898953] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.904576] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.909733] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.915792] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.921036] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.927267] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.932947] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.938820] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.945372] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.951771] sky2: driver version 1.30 <6>[ 2.956316] VFIO - User Level meta-driver version: 0.3 <6>[ 2.962073] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 2.967970] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 2.974582] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.981410] ehci-pci: EHCI PCI platform driver <6>[ 2.986150] ehci-platform: EHCI generic platform driver <6>[ 2.991727] ehci-orion: EHCI orion driver <6>[ 2.996068] ehci-exynos: EHCI Exynos driver <6>[ 3.000578] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.007053] ohci-pci: OHCI PCI platform driver <6>[ 3.011797] ohci-platform: OHCI generic platform driver <6>[ 3.017396] ohci-exynos: OHCI Exynos driver <6>[ 3.022122] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.027902] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.036000] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.045721] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 3.052316] hub 1-0:1.0: USB hub found <6>[ 3.056355] hub 1-0:1.0: 1 port detected <6>[ 3.060697] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.066472] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.074423] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.081274] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.089928] hub 2-0:1.0: USB hub found <6>[ 3.093966] hub 2-0:1.0: 1 port detected <6>[ 3.098357] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.104136] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 3.112221] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.121934] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 3.128480] hub 3-0:1.0: USB hub found <6>[ 3.132519] hub 3-0:1.0: 1 port detected <6>[ 3.136853] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.142628] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 3.150582] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.157436] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.166059] hub 4-0:1.0: USB hub found <6>[ 3.170096] hub 4-0:1.0: 1 port detected <6>[ 3.174638] usbcore: registered new interface driver usb-storage <6>[ 3.182471] i2c /dev entries driver <6>[ 3.189005] sp805-wdt c000000.watchdog: registration successful <6>[ 3.195313] sp805-wdt c010000.watchdog: registration successful <6>[ 3.202826] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 3.211544] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.218034] sdhci: Copyright(c) Pierre Ossman <6>[ 3.222974] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.229901] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.236317] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 3.236870] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 3.248230] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.255478] usbcore: registered new interface driver usbhid <6>[ 3.261339] usbhid: USB HID core driver <6>[ 3.267090] mmc0: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 3.268124] NET: Registered protocol family 17 <6>[ 3.274304] mmc1: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 3.279185] 9pnet: Installing 9P2000 support <5>[ 3.290818] Key type dns_resolver registered <6>[ 3.295579] registered taskstats version 1 <5>[ 3.299965] Loading compiled-in X.509 certificates <6>[ 3.307699] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 3.315562] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 3.321586] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 3.327769] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 3.333775] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 3.342448] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.387125] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.400863] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.420669] mmc1: new HS400 MMC card at address 0001 <6>[ 3.425935] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.433267] mmcblk1: mmc1:0001 S0J56X 7.34 GiB <6>[ 3.438297] mmcblk1boot0: mmc1:0001 S0J56X partition 1 31.5 MiB <6>[ 3.444759] mmcblk1boot1: mmc1:0001 S0J56X partition 2 31.5 MiB <6>[ 3.451072] mmcblk1rpmb: mmc1:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 3.459739] mmcblk1: p1 p2 <6>[ 3.637818] hub 3-1:1.0: USB hub found <6>[ 3.641998] hub 3-1:1.0: 7 ports detected <6>[ 6.470633] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.497767] Sending DHCP requests ., OK <6>[ 6.521980] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.98 <6>[ 6.529976] IP-Config: Complete: <6>[ 6.533496] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.98, mask=255.255.255.0, gw=172.16.0.254 <6>[ 6.543975] host=172.16.0.98, domain=lava.lan, nis-domain=(none) <6>[ 6.550782] bootserver=0.0.0.0, rootserver=10.228.65.1, rootpath= <6>[ 6.550795] nameserver0=8.8.8.8 <6>[ 6.561875] ALSA device list: <6>[ 6.565120] No soundcards found. <6>[ 6.572708] Freeing unused kernel memory: 5952K <6>[ 6.582132] Run /init as init process Loading, please wait... Starting version 247.3-7 <6>[ 6.975893] mali-dp f080000.display: Adding to iommu group 13 <4>[ 7.001670] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 7.010219] NET: Registered protocol family 10 <4>[ 7.032409] wm8904 2-001a: supply DCVDD not found, using dummy regulator <6>[ 7.034769] Segment Routing with IPv6 <4>[ 7.060002] wm8904 2-001a: supply DBVDD not found, using dummy regulator <6>[ 7.072045] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 7.092596] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.134144] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 7.165672] caam 8000000.crypto: Entropy delay = 3200 <4>[ 7.195359] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 7.199219] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 7.210424] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 7.217547] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 7.229009] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 7.235723] wm8904 2-001a: supply CPVDD not found, using dummy regulator <6>[ 7.244139] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 7.244861] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.249651] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 7.264206] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 7.269681] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 7.277677] caam 8000000.crypto: job rings = 4, qi = 0 <4>[ 7.277852] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.285405] wm8904 2-001a: revision A <6>[ 7.289954] rtc-rv8803 0-0032: registered as rtc0 <6>[ 7.301769] mscc_felix 0000:00:00.5: Adding to iommu group 14 <4>[ 7.318272] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 7.326316] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 7.326428] mscc_felix 0000:00:00.5: device is disabled, skipping <6>[ 7.333652] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 7.347294] caam algorithms registered in /proc/crypto <6>[ 7.354042] caam 8000000.crypto: registering rng-caam <6>[ 7.365487] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 7.371525] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 7.377532] caam_jr 8040000.jr: Adding to iommu group 18 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-to<5>[ 7.419847] random: crng init done p ... done. Begin: Running /scripts/nfs-premount ... done. IP-Config: eth0 hardware address 00:e0:4b:6e:9b:2b mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 172.16.0.255 IP-Config: eth0 complete (dhcp from 172.16.0.254): address: 172.16.0.98 broadcast: 172.16.0.255 netmask: 255.255.255.0 gateway: 172.16.0.254 dns0 : 8.8.8.8 dns1 : 0.0.0.0 domain : lava.lan rootserver: 172.16.0.254 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 7.789511] systemd[1]: System time before build time, advancing clock. <30>[ 7.845020] systemd[1]: systemd 247.3-7 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 7.868088] systemd[1]: Detected architecture arm64. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 7.895646] systemd[1]: Set hostname to . <30>[ 8.420405] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 8.429506] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 8.442328] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 8.452716] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. <30>[ 8.474439] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. <30>[ 8.498518] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. <30>[ 8.522353] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. <30>[ 8.545967] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. <30>[ 8.570058] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. <30>[ 8.593935] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 8.606079] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. <30>[ 8.629954] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. <30>[ 8.649894] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. <30>[ 8.669871] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. <30>[ 8.690007] systemd[1]: Reached target Swap. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. <30>[ 8.710510] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. <30>[ 8.735783] systemd[1]: Listening on Journal Audit Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Audit Socket[0m. <30>[ 8.759425] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. <30>[ 8.783017] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. <30>[ 8.803747] systemd[1]: Listening on Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink Socket[0m. <30>[ 8.829567] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. <30>[ 8.850876] systemd[1]: Listening on udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. <30>[ 8.880414] systemd[1]: Mounting Huge Pages File System... Mounting [0;1;39mHuge Pages File System[0m... <30>[ 8.904318] systemd[1]: Mounting POSIX Message Queue File System... Mounting [0;1;39mPOSIX Message Queue File System[0m... <30>[ 8.933428] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... <30>[ 8.954274] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. <30>[ 8.967371] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... <30>[ 8.997576] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module configfs[0m... <30>[ 9.021525] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... <30>[ 9.049332] systemd[1]: Starting Load Kernel Module fuse... Starting [0;1;39mLoad Kernel Module fuse[0m... <6>[ 9.066089] fuse: init (API version 7.32) <30>[ 9.073950] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 9.087244] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... <30>[ 9.111355] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mLoad Kernel Modules[0m... <30>[ 9.138044] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mRemount Root and Kernel File Systems[0m... <30>[ 9.170556] systemd[1]: Starting Coldplug All udev Devices... Starting [0;1;39mColdplug All udev Devices[0m... <30>[ 9.200353] systemd[1]: Mounted Huge Pages File System. [[0;32m OK [0m] Mounted [0;1;39mHuge Pages File System[0m. <30>[ 9.230186] systemd[1]: Mounted POSIX Message Queue File System. [[0;32m OK [0m] Mounted [0;1;39mPOSIX Message Queue File System[0m. <30>[ 9.254148] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. <30>[ 9.278649] systemd[1]: Finished Create list of static device nodes for the current kernel. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. <30>[ 9.306289] systemd[1]: Started Journal Service. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. Mounting [0;1;39mFUSE Control File System[0m... Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... Starting [0;1;39mApply Kernel Variables[0m... Starting [0;1;39mCreate System Users[<46>[ 9.525173] systemd-journald[212]: Received client request to flush runtime journal. 0m... [[0;32m OK [0m] Mounted [0;1;39mFUSE Control File System[0m. [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Service[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Reached target [0;1;39mSound Card[0m. [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. Debian GNU/Linux 11 debian-bullseye-arm64 ttyS0 debian-bullseye-arm64 login: root (automatic login) Linux debian-bullseye-arm64 5.10.131-cip13 #1 SMP PREEMPT Wed Aug 17 10:36:02 UTC 2022 aarch64 The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/155981/extract-nfsrootfs-7j4t5dcf' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/155981/extract-nfsrootfs-7j4t5dcf' / # export NFS_SERVER_IP='10.228.65.1' export NFS_SERVER_IP='10.228.65.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-155981/environment . /lava-155981/environment / # /lava-155981/bin/lava-test-runner /lava-155981/0 /lava-155981/bin/lava-test-runner /lava-155981/0 + export TESTRUN_ID=0_dmesg + cd /lava-155981/0/tests/0_dmesg + cat uuid <8>[ 12.273372] + UUID=155981_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.326259] <8>[ 12.372439] <8>[ 12.425518] + <8>[ 12.435804] set +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-155981/environment / # . /lava-155981/environment/lava-155981/bin/lava-test-runner /lava-155981/1 / # /lava-155981/bin/lava-test-runner /lava-155981/1 + export TESTRUN_ID=1_bootrr + cd /lava-155981/1/tests/1_bootrr + cat uuid + UUID=155981_1.6.<8>[ 12.957202] 2.4.5 + set +x + export PATH=/opt/bootrr/helpers:/lava-155981/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr + sh helpers/bootrr-auto /lava-155981/1/../bin/lava-test-case <8>[ 14.016111] + <8>[ 14.042659] set +x / #