[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7844750/tftp-deploy-eyi4c7x8/kernel/zImage tftp 0x10000000 7844750/tftp-deploy-eyi4c7x8/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7844750/tftp-deploy-eyi4c7x8/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 11.8 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x14000000 7844750/tftp-deploy-eyi4c7x8/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7844750/tftp-deploy-eyi4c7x8/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7844750/tftp-deploy-eyi4c7x8/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 11.5 MiB/s done Bytes transferred = 16062007 (f51637 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7844750/tftp-deploy-eyi4c7x8/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7844750/tftp-deploy-eyi4c7x8/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7844750/tftp-deploy-eyi4c7x8/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 42393 (a599 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16061943 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d598 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.147-cip18 (KernelCI@build-j454045-arm-gcc-10-multi-v7-defconfig-hc664) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Nov 4 07:46:28 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933704K/1048576K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 49336K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022223] Console: colour dummy device 80x30 <6>[ 0.024112] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034527] pid_max: default: 32768 minimum: 301 <6>[ 0.039561] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046978] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055597] CPU: Testing write buffer coherency: ok <6>[ 0.060092] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065654] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071989] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079697] rcu: Hierarchical SRCU implementation. <6>[ 0.086655] EFI services will not be available. <6>[ 0.088886] smp: Bringing up secondary CPUs ... <6>[ 0.094161] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094169] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105501] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105510] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116711] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116719] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127173] smp: Brought up 1 node, 4 CPUs <6>[ 0.131398] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137854] CPU: All CPU(s) started in SVC mode. <6>[ 0.143278] devtmpfs: initialized <6>[ 0.153572] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158904] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168784] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.178983] pinctrl core: initialized pinctrl subsystem <6>[ 0.183396] DMI not present or invalid. <6>[ 0.186575] NET: Registered protocol family 16 <6>[ 0.193811] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200377] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200562] cpuidle: using governor menu <6>[ 0.208722] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.382116] vdd1p1: supplied by regulator-dummy <6>[ 0.391012] vdd3p0: supplied by regulator-dummy <6>[ 0.399863] vdd2p5: supplied by regulator-dummy <6>[ 0.408705] vddarm: supplied by regulator-dummy <6>[ 0.417687] vddpu: supplied by regulator-dummy <6>[ 0.426279] vddsoc: supplied by regulator-dummy <6>[ 0.744785] No ATAGs? <6>[ 0.744971] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.752747] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.762849] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.773008] Serial: AMBA PL011 UART driver <6>[ 0.777169] printk: console [ramoops-1] enabled <6>[ 0.779510] pstore: Registered ramoops as persistent store backend <6>[ 0.785761] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.817009] mxs-dma 110000.dma-apbh: initialized <6>[ 0.826575] iommu: Default domain type: Translated <6>[ 0.829312] vgaarb: loaded <5>[ 0.832682] SCSI subsystem initialized <6>[ 0.836438] usbcore: registered new interface driver usbfs <6>[ 0.841618] usbcore: registered new interface driver hub <6>[ 0.847193] usbcore: registered new device driver usb <6>[ 0.853971] i2c i2c-0: IMX I2C adapter registered <6>[ 0.858781] i2c i2c-1: IMX I2C adapter registered <6>[ 0.863163] i2c i2c-2: IMX I2C adapter registered <6>[ 0.868656] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.872539] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.881972] PTP clock support registered <6>[ 0.889633] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.943559] NET: Registered protocol family 2 <6>[ 1.945757] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.954190] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.961654] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.969704] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.977141] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.983850] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.990562] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.997959] NET: Registered protocol family 1 <6>[ 2.003020] RPC: Registered named UNIX socket transport module. <6>[ 2.008581] RPC: Registered udp transport module. <6>[ 2.013570] RPC: Registered tcp transport module. <6>[ 2.018497] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.025221] PCI: CLS 0 bytes, default 64 <6>[ 2.029914] Trying to unpack rootfs image as initramfs... <6>[ 3.373213] Freeing initrd memory: 15688K <4>[ 3.375111] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.382387] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.392223] Initialise system trusted keyrings <6>[ 3.395475] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.407610] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.411603] NFS: Registering the id_resolver key type <5>[ 3.416194] Key type id_resolver registered <5>[ 3.420627] Key type id_legacy registered <6>[ 3.424954] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.431842] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.439505] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.444592] Key type asymmetric registered <5>[ 3.448441] Asymmetric key parser 'x509' registered <6>[ 3.453640] bounce: pool size: 64 pages <6>[ 3.457693] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.465340] io scheduler mq-deadline registered <6>[ 3.470116] io scheduler kyber registered <4>[ 3.516534] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.523489] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.586424] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.594597] SuperH (H)SCI(F) driver initialized <6>[ 3.597553] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.606445] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.614344] printk: console [ttymxc1] enabled <6>[ 3.614344] printk: console [ttymxc1] enabled <6>[ 3.623515] printk: bootconsole [ec_imx21] disabled <6>[ 3.623515] printk: bootconsole [ec_imx21] disabled <6>[ 3.635225] msm_serial: driver initialized <6>[ 3.641250] STMicroelectronics ASC driver initialized <6>[ 3.648498] STM32 USART driver initialized <4>[ 3.663869] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.671806] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.678614] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.695228] brd: module loaded <6>[ 3.708614] loop: module loaded <6>[ 3.715900] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.724132] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.732449] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.740916] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.748914] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.756667] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.764252] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.774886] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.782166] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.791243] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.802040] scsi host0: ahci-imx <6>[ 3.805904] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.826227] CAN device driver interface <6>[ 3.831720] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.841214] pps pps0: new PPS source ptp0 <6>[ 3.878025] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.885634] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.890892] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.897139] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.902822] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.914759] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.922495] usbcore: registered new interface driver pegasus <6>[ 3.928463] usbcore: registered new interface driver asix <6>[ 3.934182] usbcore: registered new interface driver ax88179_178a <6>[ 3.940592] usbcore: registered new interface driver cdc_ether <6>[ 3.946734] usbcore: registered new interface driver smsc75xx <6>[ 3.952806] usbcore: registered new interface driver smsc95xx <6>[ 3.958860] usbcore: registered new interface driver net1080 <6>[ 3.964838] usbcore: registered new interface driver cdc_subset <6>[ 3.971072] usbcore: registered new interface driver zaurus <6>[ 3.976976] usbcore: registered new interface driver cdc_ncm <6>[ 3.986421] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.993238] ehci-pci: EHCI PCI platform driver <6>[ 3.997989] ehci-platform: EHCI generic platform driver <6>[ 4.003804] ehci-orion: EHCI orion driver <6>[ 4.008315] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.012799] ehci-st: EHCI STMicroelectronics driver <6>[ 4.018129] ehci-exynos: EHCI Exynos driver <6>[ 4.022777] ehci-atmel: EHCI Atmel driver <6>[ 4.027224] tegra-ehci: Tegra EHCI driver <6>[ 4.031726] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.038191] ohci-pci: OHCI PCI platform driver <6>[ 4.042963] ohci-platform: OHCI generic platform driver <6>[ 4.048718] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.053210] ohci-st: OHCI STMicroelectronics driver <6>[ 4.058544] ohci-atmel: OHCI Atmel driver <6>[ 4.063900] usbcore: registered new interface driver usb-storage <6>[ 4.078253] i2c /dev entries driver <6>[ 4.101317] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.107769] sdhci: Copyright(c) Pierre Ossman <6>[ 4.115083] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.123289] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.130512] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.134613] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.135792] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.146550] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.153879] usbcore: registered new interface driver usbhid <6>[ 4.159738] usbhid: USB HID core driver <6>[ 4.161635] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.169548] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.170346] NET: Registered protocol family 10 <6>[ 4.176133] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.181618] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.182163] Segment Routing with IPv6 <6>[ 4.182235] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.182800] NET: Registered protocol family 17 <6>[ 4.182812] can: controller area network core <6>[ 4.182891] NET: Registered protocol family 29 <6>[ 4.182896] can: raw protocol <6>[ 4.182903] can: broadcast manager protocol <6>[ 4.182913] can: netlink gateway - max_hops=1 <5>[ 4.183309] Key type dns_resolver registered <6>[ 4.188339] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.190200] ThumbEE CPU extension supported. <5>[ 4.190211] Registering SWP/SWPB emulation handler <5>[ 4.190567] Loading compiled-in X.509 certificates <6>[ 4.204010] pstore: Using crash dump compression: deflate <6>[ 4.231251] mmc2: new high speed SDHC card at address 0001 <4>[ 4.253424] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 4.259203] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 4.264194] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.290411] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.291304] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.306032] GPT:29296874 != 30560255 <4>[ 4.309884] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.316156] GPT:29296874 != 30560255 <4>[ 4.320005] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.325444] mmcblk2: p1 p2 p3 <4>[ 4.332028] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.341915] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.347083] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.379685] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.386731] hub 1-0:1.0: USB hub found <6>[ 4.390824] hub 1-0:1.0: 1 port detected <6>[ 4.397457] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.413551] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.421660] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.429629] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.441825] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.449738] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.457583] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.467563] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.479761] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.487637] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.495569] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.509534] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.719669] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.921363] hub 1-1:1.0: USB hub found <6>[ 4.925599] hub 1-1:1.0: 3 ports detected <4>[ 4.939992] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.948033] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.957899] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 5.249655] usb 1-1.1: new low-speed USB device number 3 using ci_hdrc <6>[ 5.418748] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.0/0003:17EF:6009.0001/input/input1 <6>[ 5.500534] hid-generic 0003:17EF:6009.0001: input: USB HID v1.10 Keyboard [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-ci_hdrc.1-1.1/input0 <4>[ 5.525058] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.533157] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.542983] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 5.561013] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Mouse as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input2 <6>[ 5.581823] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint System Control as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input3 <6>[ 5.670231] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Consumer Control as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input4 <6>[ 5.690286] hid-generic 0003:17EF:6009.0002: input: USB HID v1.10 Mouse [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-ci_hdrc.1-1.1/input1 <4>[ 5.709616] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.717496] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.725399] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.680099] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.699734] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.729754] Sending DHCP requests ., OK <6>[ 7.773829] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 7.782171] IP-Config: Complete: <6>[ 7.785697] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.796451] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 7.804598] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.804609] nameserver0=192.168.201.1 <6>[ 7.823365] Freeing unused kernel memory: 2048K <6>[ 7.850611] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.975529] udevd[136]: starting version 3.2.9 <5>[ 7.981139] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.988089] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.994967] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.008727] udevd[136]: specified user 'tss' unknown <27>[ 8.014223] udevd[136]: specified group 'tss' unknown <30>[ 8.021894] udevd[137]: starting eudev-3.2.9 <6>[ 8.412686] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.419738] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.430102] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.438038] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.464301] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.473442] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.482367] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.491023] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.524962] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.532949] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.546937] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.601654] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.668432] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.689813] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.729771] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.736591] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.771626] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.837742] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.898503] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.903947] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.910868] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.920998] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.939717] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.946117] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.960139] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 9.013646] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.022263] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.030876] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.039462] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.041401] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 9.056148] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 9.064231] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 9.064835] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 9.077916] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 9.094000] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.102011] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.119460] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.134031] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 9.141290] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.150489] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.159040] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.167624] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <27>[ 9.185263] udevd[140]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90010, key code 190): Invalid argument <27>[ 9.214273] udevd[140]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90011, key code 148): Invalid argument <27>[ 9.233208] udevd[140]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90012, key code 152): Invalid argument <4>[ 9.233383] panel-simple panel-lcd: supply power not found, using dummy regulator <27>[ 9.246144] udevd[140]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90013, key code 236): Invalid argument <4>[ 9.254039] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.275788] panel-simple panel-lvds0: supply power not found, using dummy regulator <27>[ 9.290573] udevd[140]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90014, key code 238): Invalid argument <6>[ 9.301589] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <27>[ 9.307615] udevd[140]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90015, key code 212): Invalid argument <6>[ 9.311971] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <27>[ 9.324864] udevd[140]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90016, key code 227): Invalid argument <6>[ 9.333254] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.354487] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.431049] caam algorithms registered in /proc/crypto <6>[ 9.438749] caam 2100000.crypto: registering rng-caam <4>[ 9.446311] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.454311] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.463423] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.478863] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.487432] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.495954] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.504474] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.523319] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.531298] panel-simple panel-lcd: Specify missing connector_type done <4>[ 9.540103] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <6>[ 9.557472] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <5>[ 9.558818] random: dd: uninitialized urandom read (32 bytes read) <6>[ 9.566020] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) OK <6>[ 9.580986] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 9.589821] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) ip: RTNETLINK answers: File exists FAIL <5>[ 9.626604] random: crng init done <5>[ 9.630333] random: 1 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7844750/environment . /lava-7844750/environment / # /lava-7844750/bin/lava-test-runner /lava-7844750/0 /lava-7844750/bin/lava-test-runner /lava-7844750/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-7844750/0/tests/0_dmesg + cat uuid + UUID=7844750_1.5.2.4<8>[ 10.265260] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.311235] <8>[ 10.352030] <8>[ 10.393107] + set<8>[ 10.403077] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7844750/environment / # . /lava-7844750/environment/lava-7844750/bin/lava-test-runner /lava-7844750/1 / # /lava-7844750/bin/lava-test-runner /lava-7844750/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-7844750/1/tests/1_bootrr +<8>[ 10.913776] cat uuid + UUID=7844750_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-7844750/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7844750/1/../bin/lava-test-case <8>[ 11.976109] /lava-7844750/1/../bin/lava-test-case <8>[ 12.015672] /lava-7844750/1/../bin/lava-test-case <8>[ 12.040713] + set<8>[ 12.059726] +x / #