[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7922327/tftp-deploy-zrzhmeij/kernel/zImage tftp 0x10000000 7922327/tftp-deploy-zrzhmeij/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '7922327/tftp-deploy-zrzhmeij/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 11.7 MiB/s done Bytes transferred = 9671168 (939200 hex) => tftp 0x14000000 7922327/tftp-deploy-zrzhmeij/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7922327/tftp-deploy-zrzhmeij/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '7922327/tftp-deploy-zrzhmeij/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 11.2 MiB/s done Bytes transferred = 16060766 (f5115e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7922327/tftp-deploy-zrzhmeij/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7922327/tftp-deploy-zrzhmeij/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '7922327/tftp-deploy-zrzhmeij/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x939200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16060702 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.153-cip19 (KernelCI@build-j483482-arm-gcc-10-multi-v7-defconfig-krmf8) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Nov 9 20:57:46 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933704K/1048576K available (13312K kernel code, 2231K rwdata, 5344K rodata, 2048K init, 424K bss, 49336K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022200] Console: colour dummy device 80x30 <6>[ 0.024088] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034501] pid_max: default: 32768 minimum: 301 <6>[ 0.039538] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046955] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055565] CPU: Testing write buffer coherency: ok <6>[ 0.060084] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065635] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071974] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079724] rcu: Hierarchical SRCU implementation. <6>[ 0.086775] EFI services will not be available. <6>[ 0.089010] smp: Bringing up secondary CPUs ... <6>[ 0.094282] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094290] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105625] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105634] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116833] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116841] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127287] smp: Brought up 1 node, 4 CPUs <6>[ 0.131518] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137971] CPU: All CPU(s) started in SVC mode. <6>[ 0.143383] devtmpfs: initialized <6>[ 0.153905] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159231] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169112] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179331] pinctrl core: initialized pinctrl subsystem <6>[ 0.183777] DMI not present or invalid. <6>[ 0.186922] NET: Registered protocol family 16 <6>[ 0.194176] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200783] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200981] cpuidle: using governor menu <6>[ 0.209089] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.385266] vdd1p1: supplied by regulator-dummy <6>[ 0.394267] vdd3p0: supplied by regulator-dummy <6>[ 0.403214] vdd2p5: supplied by regulator-dummy <6>[ 0.412177] vddarm: supplied by regulator-dummy <6>[ 0.421282] vddpu: supplied by regulator-dummy <6>[ 0.430003] vddsoc: supplied by regulator-dummy <6>[ 0.753347] No ATAGs? <6>[ 0.753532] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.761310] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.771473] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.781726] Serial: AMBA PL011 UART driver <6>[ 0.785910] printk: console [ramoops-1] enabled <6>[ 0.788222] pstore: Registered ramoops as persistent store backend <6>[ 0.794456] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.832169] iommu: Default domain type: Translated <6>[ 0.834875] vgaarb: loaded <5>[ 0.838328] SCSI subsystem initialized <6>[ 0.842016] usbcore: registered new interface driver usbfs <6>[ 0.847251] usbcore: registered new interface driver hub <6>[ 0.852767] usbcore: registered new device driver usb <6>[ 0.859567] i2c i2c-0: IMX I2C adapter registered <6>[ 0.864345] i2c i2c-1: IMX I2C adapter registered <6>[ 0.868801] i2c i2c-2: IMX I2C adapter registered <6>[ 0.874241] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.878155] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.887560] PTP clock support registered <6>[ 0.895232] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.028303] NET: Registered protocol family 2 <6>[ 2.030517] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.038915] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.046405] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.054424] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.061904] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.068591] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.075301] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.082703] NET: Registered protocol family 1 <6>[ 2.087832] RPC: Registered named UNIX socket transport module. <6>[ 2.093322] RPC: Registered udp transport module. <6>[ 2.098314] RPC: Registered tcp transport module. <6>[ 2.103239] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.109964] PCI: CLS 0 bytes, default 64 <6>[ 2.114605] Trying to unpack rootfs image as initramfs... <6>[ 3.470576] Freeing initrd memory: 15688K <4>[ 3.472431] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.479765] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.489624] Initialise system trusted keyrings <6>[ 3.492734] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.505035] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.509010] NFS: Registering the id_resolver key type <5>[ 3.513633] Key type id_resolver registered <5>[ 3.518061] Key type id_legacy registered <6>[ 3.522374] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.529279] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.536951] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.541999] Key type asymmetric registered <5>[ 3.545897] Asymmetric key parser 'x509' registered <6>[ 3.551039] bounce: pool size: 64 pages <6>[ 3.555117] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.562764] io scheduler mq-deadline registered <6>[ 3.567542] io scheduler kyber registered <6>[ 3.610937] mxs-dma 110000.dma-apbh: initialized <4>[ 3.617749] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.624661] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.680997] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.689185] SuperH (H)SCI(F) driver initialized <6>[ 3.692129] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.701039] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.708943] printk: console [ttymxc1] enabled <6>[ 3.708943] printk: console [ttymxc1] enabled <6>[ 3.718106] printk: bootconsole [ec_imx21] disabled <6>[ 3.718106] printk: bootconsole [ec_imx21] disabled <6>[ 3.729810] msm_serial: driver initialized <6>[ 3.735847] STMicroelectronics ASC driver initialized <6>[ 3.743131] STM32 USART driver initialized <4>[ 3.758577] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.766498] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.773306] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.790118] brd: module loaded <6>[ 3.803427] loop: module loaded <6>[ 3.810783] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.818996] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.827299] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.835758] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.843755] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.851529] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.859093] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.869688] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.876989] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.886065] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.896878] scsi host0: ahci-imx <6>[ 3.900749] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.921300] CAN device driver interface <6>[ 3.926783] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.936308] pps pps0: new PPS source ptp0 <6>[ 3.973031] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.980643] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.985900] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.992145] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.997828] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.009769] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.017502] usbcore: registered new interface driver pegasus <6>[ 4.023470] usbcore: registered new interface driver asix <6>[ 4.029188] usbcore: registered new interface driver ax88179_178a <6>[ 4.035606] usbcore: registered new interface driver cdc_ether <6>[ 4.041750] usbcore: registered new interface driver smsc75xx <6>[ 4.047823] usbcore: registered new interface driver smsc95xx <6>[ 4.053869] usbcore: registered new interface driver net1080 <6>[ 4.059845] usbcore: registered new interface driver cdc_subset <6>[ 4.066077] usbcore: registered new interface driver zaurus <6>[ 4.071991] usbcore: registered new interface driver cdc_ncm <6>[ 4.081523] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.088349] ehci-pci: EHCI PCI platform driver <6>[ 4.093098] ehci-platform: EHCI generic platform driver <6>[ 4.098930] ehci-orion: EHCI orion driver <6>[ 4.103432] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.107927] ehci-st: EHCI STMicroelectronics driver <6>[ 4.113262] ehci-exynos: EHCI Exynos driver <6>[ 4.117907] ehci-atmel: EHCI Atmel driver <6>[ 4.122355] tegra-ehci: Tegra EHCI driver <6>[ 4.126869] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.133334] ohci-pci: OHCI PCI platform driver <6>[ 4.138104] ohci-platform: OHCI generic platform driver <6>[ 4.143875] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.148362] ohci-st: OHCI STMicroelectronics driver <6>[ 4.153695] ohci-atmel: OHCI Atmel driver <6>[ 4.159063] usbcore: registered new interface driver usb-storage <6>[ 4.173384] i2c /dev entries driver <6>[ 4.196601] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.203052] sdhci: Copyright(c) Pierre Ossman <6>[ 4.210392] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.218646] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.225872] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.230052] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.231137] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.241887] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.249297] usbcore: registered new interface driver usbhid <6>[ 4.255139] usbhid: USB HID core driver <6>[ 4.255289] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.264946] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.265807] NET: Registered protocol family 10 <6>[ 4.271519] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.277013] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.277379] Segment Routing with IPv6 <6>[ 4.277449] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.278023] NET: Registered protocol family 17 <6>[ 4.278036] can: controller area network core <6>[ 4.278108] NET: Registered protocol family 29 <6>[ 4.278113] can: raw protocol <6>[ 4.278120] can: broadcast manager protocol <6>[ 4.278130] can: netlink gateway - max_hops=1 <5>[ 4.278538] Key type dns_resolver registered <6>[ 4.285587] ThumbEE CPU extension supported. <6>[ 4.294998] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <5>[ 4.300941] Registering SWP/SWPB emulation handler <6>[ 4.331334] mmc2: new high speed SDHC card at address aaaa <5>[ 4.332074] Loading compiled-in X.509 certificates <6>[ 4.337129] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <6>[ 4.348751] pstore: Using crash dump compression: deflate <4>[ 4.369009] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.377662] GPT:7812499 != 31116287 <4>[ 4.381425] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.387732] GPT:7812499 != 31116287 <4>[ 4.390860] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.391495] GPT: Use GNU Parted to correct GPT errors. <4>[ 4.399448] panel-simple panel-lcd: Specify missing connector_type <6>[ 4.404696] mmcblk2: p1 p2 p3 <4>[ 4.412638] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.431043] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.441696] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.446895] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.475333] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.482446] hub 1-0:1.0: USB hub found <6>[ 4.486614] hub 1-0:1.0: 1 port detected <6>[ 4.495279] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.512184] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.520104] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.528029] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.540170] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.548076] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.555961] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.565934] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.578159] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.586077] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.593952] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.608116] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.815280] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.016910] hub 1-1:1.0: USB hub found <6>[ 5.021109] hub 1-1:1.0: 3 ports detected <4>[ 5.031684] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.039659] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.047921] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.765728] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.795306] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.825259] Sending DHCP requests ., OK <6>[ 7.869427] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 <6>[ 7.877756] IP-Config: Complete: <6>[ 7.881278] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.892001] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) <6>[ 7.900107] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.900112] nameserver0=192.168.201.1 <6>[ 7.917497] Freeing unused kernel memory: 2048K <6>[ 7.956201] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.087072] udevd[138]: starting version 3.2.9 <5>[ 8.092829] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.100468] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.107405] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.121135] udevd[138]: specified user 'tss' unknown <27>[ 8.126694] udevd[138]: specified group 'tss' unknown <30>[ 8.134228] udevd[139]: starting eudev-3.2.9 <6>[ 8.449936] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.459750] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.467714] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.487314] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.497043] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.520941] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.528918] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.573661] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.582302] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.587112] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.590961] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.607329] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.624167] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.632134] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.657253] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.717450] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.752820] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.761307] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.768176] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.794864] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.826111] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.832492] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.895546] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.928761] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.994898] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 9.055657] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 9.061083] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 9.067989] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 9.078385] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.086982] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.095564] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.104092] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.125464] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 9.127201] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.133625] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 9.141350] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.149815] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 9.161592] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.164290] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 9.196193] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 9.196607] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.209852] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 9.217924] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.226547] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.235080] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.250834] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.258894] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.268492] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.280754] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.289452] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.298030] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.306613] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.562789] caam algorithms registered in /proc/crypto <6>[ 9.569753] caam 2100000.crypto: registering rng-caam <4>[ 9.580946] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.588964] panel-simple panel-lcd: Specify missing connector_type done <4>[ 9.607661] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <6>[ 9.620241] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <5>[ 9.625694] random: dd: uninitialized urandom read (32 bytes read) <6>[ 9.628813] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) OK <6>[ 9.643710] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.652475] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 9.728550] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control t<5>[ 9.757498] random: crng init done urned off / # <5>[ 9.763295] random: 1 urandom warning(s) missed due to ratelimiting / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7922327/environment . /lava-7922327/environment / # /lava-7922327/bin/lava-test-runner /lava-7922327/0 /lava-7922327/bin/lava-test-runner /lava-7922327/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-7922327/0/tests/0_dmesg + cat uuid + UUID=7922327_1.5.2.4<8>[ 10.351609] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.398066] <8>[ 10.439305] <8>[ 10.480651] + set<8>[ 10.490529] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7922327/environment / # . /lava-7922327/environment/lava-7922327/bin/lava-test-runner /lava-7922327/1 / # /lava-7922327/bin/lava-test-runner /lava-7922327/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-7922327/1/tests/1_bootrr +<8>[ 10.996693] cat uuid + UUID=7922327_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-7922327/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7922327/1/../bin/lava-test-case <8>[ 12.050788] /lava-7922327/1/../bin/lava-test-case <8>[ 12.090485] /lava-7922327/1/../bin/lava-test-case <8>[ 12.115485] + set<8>[ 12.134215] +x / #