[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (2 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 8138415/tftp-deploy-bc7_oxoo/kernel/zImage tftp 0x10000000 8138415/tftp-deploy-bc7_oxoo/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '8138415/tftp-deploy-bc7_oxoo/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ### 11.8 MiB/s done Bytes transferred = 12448256 (bdf200 hex) => tftp 0x14000000 8138415/tftp-deploy-bc7_oxoo/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8138415/tftp-deploy-bc7_oxoo/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '8138415/tftp-deploy-bc7_oxoo/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# # 11.8 MiB/s done Bytes transferred = 15271652 (e906e4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8138415/tftp-deploy-bc7_oxoo/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8138415/tftp-deploy-bc7_oxoo/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '8138415/tftp-deploy-bc7_oxoo/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8138415/extract-nfsrootfs-7qd66ns5,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8138415/extract-nfsrootfs-7qd66ns5,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbdf200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15271588 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.155-cip21 (KernelCI@build-j588776-arm-gcc-10-multi-v7-defconfig-kselftest-x89h9) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Nov 26 10:42:54 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8138415/extract-nfsrootfs-7qd66ns5,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 921604K/1048576K available (17408K kernel code, 2654K rwdata, 8120K rodata, 2048K init, 6693K bss, 61436K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 56055 entries in 165 pages [ 0.000000] ftrace: allocated 165 pages with 4 groups [ 0.000000] Running RCU self tests [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000042] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004481] Console: colour dummy device 80x30 [ 0.004550] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.004580] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.004607] ... MAX_LOCK_DEPTH: 48 [ 0.004634] ... MAX_LOCKDEP_KEYS: 8192 [ 0.004659] ... CLASSHASH_SIZE: 4096 [ 0.004685] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.004711] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.004738] ... CHAINHASH_SIZE: 32768 [ 0.004765] memory used by lock dependency info: 4061 kB [ 0.004791] memory used for stack traces: 2112 kB [ 0.004816] per task-struct memory footprint: 1536 bytes [ 0.004914] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004966] pid_max: default: 32768 minimum: 301 [ 0.005341] LSM: Security Framework initializing [ 0.005453] LSM support for eBPF active [ 0.005602] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005654] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.008224] CPU: Testing write buffer coherency: ok [ 0.008347] CPU0: Spectre v2: using BPIALL workaround [ 0.009441] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.013335] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.015791] rcu: Hierarchical SRCU implementation. [ 0.025470] EFI services will not be available. [ 0.026793] smp: Bringing up secondary CPUs ... [ 0.030157] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.030173] CPU1: Spectre v2: using BPIALL workaround [ 0.034227] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.034242] CPU2: Spectre v2: using BPIALL workaround [ 0.037922] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.037937] CPU3: Spectre v2: using BPIALL workaround [ 0.038814] smp: Brought up 1 node, 4 CPUs [ 0.038861] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.039049] CPU: All CPU(s) started in SVC mode. [ 0.041808] devtmpfs: initialized [ 0.099302] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.101960] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.102036] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.106807] pinctrl core: initialized pinctrl subsystem [ 0.113843] DMI not present or invalid. [ 0.116152] NET: Registered protocol family 16 [ 0.127815] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.137460] thermal_sys: Registered thermal governor 'step_wise' [ 0.138018] cpuidle: using governor menu [ 0.138545] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.894455] vdd1p1: supplied by regulator-dummy [ 0.926643] vdd3p0: supplied by regulator-dummy [ 0.958378] vdd2p5: supplied by regulator-dummy [ 0.990245] vddarm: supplied by regulator-dummy [ 1.022922] vddpu: supplied by regulator-dummy [ 1.053739] vddsoc: supplied by regulator-dummy [ 2.403832] No ATAGs? [ 2.404592] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 2.404676] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 2.424582] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 2.454123] Serial: AMBA PL011 UART driver [ 2.519933] Kprobes globally optimized [ 2.639811] iommu: Default domain type: Translated [ 2.641941] vgaarb: loaded [ 2.646785] SCSI subsystem initialized [ 2.649059] usbcore: registered new interface driver usbfs [ 2.649368] usbcore: registered new interface driver hub [ 2.649605] usbcore: registered new device driver usb [ 2.657284] i2c i2c-0: IMX I2C adapter registered [ 2.664471] i2c i2c-1: IMX I2C adapter registered [ 2.669100] i2c i2c-2: IMX I2C adapter registered [ 2.673719] pps_core: LinuxPPS API ver. 1 registered [ 2.673760] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.673859] PTP clock support registered [ 2.692030] clocksource: Switched to clocksource mxc_timer1 [ 4.443318] NET: Registered protocol family 2 [ 4.444068] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 4.447479] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) [ 4.447666] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 4.447898] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) [ 4.449337] TCP: Hash tables configured (established 8192 bind 8192) [ 4.450398] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) [ 4.450741] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.451005] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.451908] NET: Registered protocol family 1 [ 4.454760] RPC: Registered named UNIX socket transport module. [ 4.454851] RPC: Registered udp transport module. [ 4.454892] RPC: Registered tcp transport module. [ 4.454930] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.454985] NET: Registered protocol family 44 [ 4.455053] PCI: CLS 0 bytes, default 64 [ 4.457537] Trying to unpack rootfs image as initramfs... [ 6.329248] Freeing initrd memory: 14916K [ 6.330199] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 6.332312] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 6.341379] Initialise system trusted keyrings [ 6.342745] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 6.394733] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 6.398907] NFS: Registering the id_resolver key type [ 6.399185] Key type id_resolver registered [ 6.399281] Key type id_legacy registered [ 6.399946] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.400052] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.400249] ntfs: driver 2.1.32 [Flags: R/O]. [ 6.402629] Key type asymmetric registered [ 6.402758] Asymmetric key parser 'x509' registered [ 6.403196] bounce: pool size: 64 pages [ 6.403372] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 6.403477] io scheduler mq-deadline registered [ 6.403520] io scheduler kyber registered [ 6.404465] test_firmware: interface ready [ 6.587095] mxs-dma 110000.dma-apbh: initialized [ 6.653074] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 6.653342] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 6.924224] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.945388] SuperH (H)SCI(F) driver initialized [ 6.948434] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 6.953772] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 7.886154] printk: console [ttymxc1] enabled [ 7.897139] msm_serial: driver initialized [ 7.902469] STMicroelectronics ASC driver initialized [ 7.914272] STM32 USART driver initialized [ 7.941296] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 [ 7.963900] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.972403] panel-simple panel-lcd: Specify missing connector_type [ 7.980238] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.036145] brd: module loaded [ 8.099419] loop: module loaded [ 8.106009] lkdtm: No crash points registered, enable through debugfs [ 8.128595] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 8.136646] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 8.144765] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 8.153114] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 8.161130] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 8.169403] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 8.177256] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 8.188663] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 8.195796] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 8.204690] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 8.219237] scsi host0: ahci-imx [ 8.224996] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 8.292135] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 8.305969] pps pps0: new PPS source ptp0 [ 8.352712] fec 2188000.ethernet eth0: registered PHC device 0 [ 8.363682] e1000e: Intel(R) PRO/1000 Network Driver [ 8.368691] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 8.374963] igb: Intel(R) Gigabit Ethernet Network Driver [ 8.380399] igb: Copyright (c) 2007-2014 Intel Corporation. [ 8.408777] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 8.416437] usbcore: registered new interface driver pegasus [ 8.422399] usbcore: registered new interface driver asix [ 8.427984] usbcore: registered new interface driver ax88179_178a [ 8.434331] usbcore: registered new interface driver cdc_ether [ 8.440413] usbcore: registered new interface driver smsc75xx [ 8.446464] usbcore: registered new interface driver smsc95xx [ 8.452444] usbcore: registered new interface driver net1080 [ 8.458281] usbcore: registered new interface driver cdc_subset [ 8.464479] usbcore: registered new interface driver zaurus [ 8.470349] usbcore: registered new interface driver cdc_ncm [ 8.489226] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.495927] ehci-pci: EHCI PCI platform driver [ 8.500567] ehci-platform: EHCI generic platform driver [ 8.506917] ehci-orion: EHCI orion driver [ 8.511947] SPEAr-ehci: EHCI SPEAr driver [ 8.516878] ehci-st: EHCI STMicroelectronics driver [ 8.522727] ehci-exynos: EHCI Exynos driver [ 8.527820] ehci-atmel: EHCI Atmel driver [ 8.532798] tegra-ehci: Tegra EHCI driver [ 8.537754] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.544095] ohci-pci: OHCI PCI platform driver [ 8.548749] ohci-platform: OHCI generic platform driver [ 8.555048] SPEAr-ohci: OHCI SPEAr driver [ 8.559974] ohci-st: OHCI STMicroelectronics driver [ 8.565836] ohci-atmel: OHCI Atmel driver [ 8.573538] usbcore: registered new interface driver usb-storage [ 8.584445] ata1: SATA link down (SStatus 0 SControl 300) [ 8.590244] ahci-imx 2200000.sata: no device found, disabling link. [ 8.596638] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 8.613659] i2c /dev entries driver [ 8.703024] sdhci: Secure Digital Host Controller Interface driver [ 8.709246] sdhci: Copyright(c) Pierre Ossman [ 8.723617] Synopsys Designware Multimedia Card Interface Driver [ 8.737310] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.746854] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 8.746860] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 8.757185] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 8.764250] ledtrig-cpu: registered to indicate activity on CPUs [ 8.774289] usbcore: registered new interface driver usbhid [ 8.779903] usbhid: USB HID core driver [ 8.801549] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 8.801606] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 8.809225] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 8.823802] gre: GRE over IPv4 demultiplexor driver [ 8.828726] ip_gre: GRE over IPv4 tunneling driver [ 8.839803] IPv4 over IPsec tunneling driver [ 8.849411] NET: Registered protocol family 10 [ 8.858601] mmc2: new high speed SDHC card at address aaaa [ 8.860721] Segment Routing with IPv6 [ 8.868466] mmcblk2: mmc2:aaaa SL16G 14.8 GiB [ 8.874889] ip6_gre: GRE over IPv6 tunneling driver [ 8.883182] NET: Registered protocol family 17 [ 8.889319] 8021q: 802.1Q VLAN Support v1.8 [ 8.891875] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 8.894634] Key type dns_resolver registered [ 8.901039] GPT:29296874 != 31116287 [ 8.909005] GPT:Alternate GPT header not at the end of the disk. [ 8.915206] GPT:29296874 != 31116287 [ 8.918826] GPT: Use GNU Parted to correct GPT errors. [ 8.924154] mmcblk2: p1 p2 p3 [ 8.924536] ThumbEE CPU extension supported. [ 8.931641] Registering SWP/SWPB emulation handler [ 8.937855] Loading compiled-in X.509 certificates [ 9.125583] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.133998] panel-simple panel-lcd: Specify missing connector_type [ 9.147389] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.184784] imx_usb 2184200.usb: No over current polarity defined [ 9.198110] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 9.203457] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 9.232455] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 9.253505] hub 1-0:1.0: USB hub found [ 9.259835] hub 1-0:1.0: 1 port detected [ 9.276664] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 9.309607] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.317979] panel-simple panel-lcd: Specify missing connector_type [ 9.331373] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.362942] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.371201] panel-simple panel-lcd: Specify missing connector_type [ 9.384621] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.403883] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 9.433419] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.441818] panel-simple panel-lcd: Specify missing connector_type [ 9.455205] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.477180] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 9.492592] IP-Config: Failed to open gretap0 [ 9.496995] IP-Config: Failed to open erspan0 [ 9.521804] Sending DHCP requests . [ 9.662309] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 9.881400] hub 1-1:1.0: USB hub found [ 9.885881] hub 1-1:1.0: 3 ports detected [ 9.920886] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.929463] panel-simple panel-lcd: Specify missing connector_type [ 9.945449] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 11.961971] . [ 12.633391] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 12.643651] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.222029] ., OK [ 16.274384] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 [ 16.282638] IP-Config: Complete: [ 16.285954] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 [ 16.296488] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) [ 16.304386] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 16.304404] nameserver0=192.168.201.1 [ 16.365257] Freeing unused kernel memory: 2048K [ 16.372587] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 20.523179] imx-ipuv3 2400000.ipu: IPUv3H probed [ 20.569687] panel-simple panel-lcd: supply power not found, using dummy regulator [ 20.577220] imx-ipuv3 2800000.ipu: IPUv3H probed [ 20.588102] panel-simple panel-lcd: Specify missing connector_type [ 20.603379] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 20.638749] panel-simple panel-lcd: supply power not found, using dummy regulator [ 20.670644] CAN device driver interface [ 20.686022] panel-simple panel-lcd: Specify missing connector_type [ 20.718325] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 20.777260] panel-simple panel-lcd: supply power not found, using dummy regulator [ 20.799361] panel-simple panel-lcd: Specify missing connector_type [ 20.818810] caam 2100000.crypto: Entropy delay = 3200 [ 20.821596] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 20.884838] caam 2100000.crypto: Instantiated RNG4 SH0 [ 20.945597] caam 2100000.crypto: Instantiated RNG4 SH1 [ 20.950798] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 20.955741] panel-simple panel-lcd: supply power not found, using dummy regulator [ 20.957523] caam 2100000.crypto: job rings = 2, qi = 0 [ 20.966306] panel-simple panel-lcd: Specify missing connector_type [ 20.988924] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 21.028656] panel-simple panel-lcd: supply power not found, using dummy regulator [ 21.037542] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 21.048810] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 21.057431] panel-simple panel-lcd: Specify missing connector_type [ 21.079425] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 21.086003] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 21.094666] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 21.102053] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 21.104026] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 21.121395] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 21.121503] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 21.128136] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 21.156048] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 21.173188] panel-simple panel-lcd: supply power not found, using dummy regulator [ 21.181806] panel-simple panel-lcd: Specify missing connector_type [ 21.197312] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 21.235014] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 21.253142] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 21.259412] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 21.269480] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 [ 21.282603] panel-simple panel-lcd: supply power not found, using dummy regulator [ 21.292822] panel-simple panel-lcd: Specify missing connector_type [ 21.309071] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 21.309846] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 21.317907] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 21.334074] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 21.342860] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 21.362336] panel-simple panel-lcd: supply power not found, using dummy regulator [ 21.370721] panel-simple panel-lcd: Specify missing connector_type [ 21.385331] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 21.438181] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 21.446994] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 21.455581] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 21.464147] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 21.927696] caam algorithms registered in /proc/crypto [ 21.956749] caam 2100000.crypto: registering rng-caam [ 21.978705] panel-simple panel-lcd: supply power not found, using dummy regulator [ 21.987294] panel-simple panel-lcd: Specify missing connector_type [ 22.007496] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 22.056425] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 22.064936] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 22.074062] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 22.082571] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) Begin: Loading essential drivers ... done. [ 22.098010] panel-simple panel-lcd: supply power not found, using dummy regulator Begin: Running /scripts/init-prem[ 22.106706] panel-simple panel-lcd: Specify missing connector_type ount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. [ 22.130990] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 22.145947] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: erspan0 hardware address 00:00:00:00:00:00 mtu 1450 DHCP SIOCSIFFLAGS: Cannot assign requested address IP-Config: gretap0 hardware address 00:00:00:00:00:00 mtu 1462 DHCP SIOCSIFFLAGS: Cannot assign requested address IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 24.353808] systemd[1]: System time before build time, advancing clock. [ 24.629084] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 24.659207] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 24.730117] systemd[1]: Set hostname to . [ 26.537868] systemd[1]: Queued start job for default target Graphical Interface. [ 26.552330] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 26.607471] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 26.657528] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 26.706662] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 26.756608] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 26.805765] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 26.853624] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 26.867600] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 26.914422] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 26.952351] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 26.992806] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 27.032976] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 27.074308] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 27.171638] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 27.185752] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 27.225647] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 27.269324] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 27.324302] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 27.364762] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 27.406364] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 27.417753] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 27.441031] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 27.496627] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 27.564365] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 27.633891] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 27.684956] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 27.735206] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 27.793683] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 27.819330] fuse: init (API version 7.32) [ 27.830693] systemd[1]: Starting Journal Service... Starting Journal Service... [ 27.897986] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 27.945475] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 28.003830] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 28.084288] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 28.133742] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 28.190606] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 28.285141] systemd[1]: modprobe@configfs.service: Succeeded. [ 28.295687] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 28.347806] systemd[1]: modprobe@drm.service: Succeeded. [ 28.358377] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 28.397851] systemd[1]: modprobe@fuse.service: Succeeded. [ 28.409029] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 28.467843] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. [ 28.507612] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. [ 28.564583] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 28.622199] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... [ 28.680229] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 28.690037] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 28.708901] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... [ 28.753718] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 28.816067] systemd[1]: Starting Create System Users... Starting Create System Users... [ 28.872262] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Flush Journal to Persistent Storage... Starting Create Static Device Nodes in /dev... [ 29.318326] systemd-journald[271]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.155-cip21 #1 SMP Sat Nov 26 10:42:54 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8138415/extract-nfsrootfs-7qd66ns5' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8138415/extract-nfsrootfs-7qd66ns5' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-8138415/environment . /lava-8138415/environment / # /lava-8138415/bin/lava-test-runner /lava-8138415/0 /lava-8138415/bin/lava-test-runner /lava-8138415/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-8138415/0/tests/0_timesync-off ++ cat uuid + UUID=8138415_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-lib + TESTRUN_ID=1_kselftest-lib + cd /lava-8138415/0/tests/1_kselftest-lib ++ cat uuid + UUID=8138415_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c lib -T '' -t kselftest_armhf.tar.gz -s false -u http://storage.kernelci.org/cip/linux-5.10.y-cip/v5.10.155-cip21/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-8138415/0/tests/1_kselftest-lib/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: Installing sed perl wget xz-utils iproute2 Hit:1 http://deb.debian.org/debian bullseye InRelease Reading package lists... Reading package lists... Building dependency tree... Reading state information... iproute2 is already the newest version (5.10.0-4). perl is already the newest version (5.32.1-4+deb11u2). sed is already the newest version (4.7-1). wget is already the newest version (1.21-1+deb11u1). xz-utils is already the newest version (5.2.5-2.1~deb11u1). 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. --2022-11-26 10:57:17-- http://storage.kernelci.org/cip/linux-5.10.y-cip/v5.10.155-cip21/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1407668 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 50.15K 177KB/s kselftest.tar.xz 7%[> ] 102.47K 179KB/s kselftest.tar.xz 14%[=> ] 197.21K 228KB/s kselftest.tar.xz 18%[==> ] 255.67K 222KB/s kselftest.tar.xz 23%[===> ] 327.79K 228KB/s kselftest.tar.xz 29%[====> ] 401.32K 232KB/s kselftest.tar.xz 34%[=====> ] 477.68K 237KB/s kselftest.tar.xz 40%[=======> ] 551.21K 239KB/s kselftest.tar.xz 46%[========> ] 632.75K 244KB/s kselftest.tar.xz 51%[=========> ] 709.59K 246KB/s kselftest.tar.xz 55%[==========> ] 758.60K 239KB/s eta 3s kselftest.tar.xz 60%[===========> ] 828.37K 239KB/s eta 3s kselftest.tar.xz 63%[===========> ] 868.89K 231KB/s eta 3s kselftest.tar.xz 66%[============> ] 911.80K 225KB/s eta 3s kselftest.tar.xz 68%[============> ] 935.35K 215KB/s eta 2s kselftest.tar.xz 69%[============> ] 958.46K 210KB/s eta 2s kselftest.tar.xz 71%[=============> ] 976.85K 206KB/s eta 2s kselftest.tar.xz 72%[=============> ] 999.47K 198KB/s eta 2s kselftest.tar.xz 75%[==============> ] 1.01M 181KB/s eta 2s kselftest.tar.xz 76%[==============> ] 1.03M 171KB/s eta 2s kselftest.tar.xz 79%[==============> ] 1.06M 152KB/s eta 2s kselftest.tar.xz 80%[===============> ] 1.08M 139KB/s eta 2s kselftest.tar.xz 82%[===============> ] 1.11M 129KB/s eta 2s kselftest.tar.xz 84%[===============> ] 1.13M 118KB/s eta 2s kselftest.tar.xz 85%[================> ] 1.15M 110KB/s eta 1s kselftest.tar.xz 87%[================> ] 1.17M 98.7KB/s eta 1s kselftest.tar.xz 89%[================> ] 1.20M 100KB/s eta 1s kselftest.tar.xz 90%[=================> ] 1.22M 88.4KB/s eta 1s kselftest.tar.xz 92%[=================> ] 1.24M 84.3KB/s eta 1s kselftest.tar.xz 93%[=================> ] 1.26M 85.4KB/s eta 1s kselftest.tar.xz 95%[==================> ] 1.28M 81.1KB/s eta 1s kselftest.tar.xz 96%[==================> ] 1.30M 77.9KB/s eta 1s kselftest.tar.xz 98%[==================> ] 1.32M 79.9KB/s eta 1s kselftest.tar.xz 99%[==================> ] 1.34M 79.5KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.34M 78.8KB/s in 9.9s 2022-11-26 10:57:27 (140 KB/s) - 'kselftest.tar.xz' saved [1407668/1407668] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ============== Tests to run =============== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ===========End Tests to run =============== [ 90.956137] kselftest: Running tests in lib TAP version 13 1..4 # selftests: lib: printf.sh [ 91.335116] test_printf: loaded. [ 91.341890] test_printf: all 384 tests passed [ 91.409715] test_printf: unloaded. # printf: ok ok 1 selftests: lib: printf.sh # selftests: lib: bitmap.sh [ 91.807685] test_bitmap: loaded. [ 91.811846] test_bitmap: parselist: 14: input is '0-2047:128/256' OK, Time: 3666 [ 91.831849] test_bitmap: all 1679 tests passed [ 91.879082] test_bitmap: unloaded. # bitmap: ok ok 2 selftests: lib: bitmap.sh # selftests: lib: prime_numbers.sh [ 92.897780] prime numbers: selftest(65536) passed, last prime was 65521 # prime numbers: ok ok 3 selftests: lib: prime_numbers.sh # selftests: lib: strscpy.sh [ 93.321661] test_strscpy: loaded. [ 93.325189] test_strscpy: all 32 tests passed [ 93.371323] test_strscpy: unloaded. # strscpy*: ok ok 4 selftests: lib: strscpy.sh + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #