Trying 192.168.56.21... Connected to conserv1. Escape character is '^]'. ser2net port telnet,3003 device serialdev, /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2.2.3:1.0-port0, 115200n81, local=false [] (Debian GNU/Linux) U-Boot SPL 2022.07-rc3-dirty (May 24 2022 - 12:39:48 +0100) Trying to boot from MMC1 U-Boot 2022.07-rc3-dirty (May 24 2022 - 12:39:48 +0100) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB Core: 160 devices, 18 uclasses, devicetree: separate WDT: Started wdt@44e35000 with servicing (60s timeout) 7[r[999;999H[6n8NAND: U-Boot SPL 2022.07-rc3-dirty (May 24 2022 - 12:39:48 +0100) Trying to boot from MMC1 U-Boot 2022.07-rc3-dirty (May 24 2022 - 12:39:48 +0100) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB Core: 160 devices, 18 uclasses, devicetree: separate WDT: Started wdt@44e35000 with servicing (60s timeout) 7[r[999;999H[6n8NAND: U-Boot SPL 2022.07-rc3-dirty (May 24 2022 - 12:39:48 +0100) Trying to boot from MMC1 U-Boot 2022.07-rc3-dirty (May 24 2022 - 12:39:48 +0100) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB Core: 160 devices, 18 uclasses, devicetree: separate WDT: Started wdt@44e35000 with servicing (60s timeout) 7[r[999;999H[6n8NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... Unable to use mmc 0:1... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 *** Unhandled DHCP Option in OFFER/ACK: 42 *** Unhandled DHCP Option in OFFER/ACK: 42 DHCP client bound to address 192.168.56.135 (297 ms) => setenv serverip 192.168.56.123 setenv serverip 192.168.56.123 => tftp 0x82000000 205972/tftp-deploy-ojkd73rx/kernel/zImage tftp 0x82000000 205972/tftp-deploy-ojkd73rx/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.56.123; our IP address is 192.168.56.135 Filename '205972/tftp-deploy-ojkd73rx/kernel/zImage'. Load address: 0x82000000 Loading: *################################################## 4.4 MiB 4.3 MiB/s done Bytes transferred = 4589520 (4607d0 hex) => tftp 0x83000000 205972/tftp-deploy-ojkd73rx/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 205972/tftp-deploy-ojkd73rx/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.56.123; our IP address is 192.168.56.135 Filename '205972/tftp-deploy-ojkd73rx/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################## 13.5 MiB 4.5 MiB/s done Bytes transferred = 14122663 (d77ea7 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 205972/tftp-deploy-ojkd73rx/dtb/am335x-boneblack.dtb tftp 0x88000000 205972/tftp-deploy-ojkd73rx/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.56.123; our IP address is 192.168.56.135 Filename '205972/tftp-deploy-ojkd73rx/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *################################################## 61.4 KiB 3.5 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x4607d0 ] ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2022-11-26 10:51:34 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14122599 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.155-cip21 (KernelCI@build-j588719-arm-gcc-10-omap2plus-defconfig-pkdf9) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Nov 26 10:35:52 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472076K/522240K available (9216K kernel code, 1025K rwdata, 2168K rodata, 1024K init, 281K bss, 33780K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018557] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030197] Console: colour dummy device 80x30 <3>[ 0.035070] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042129] This ensures that you still see kernel messages. Please <3>[ 0.048856] update your kernel commandline. <6>[ 0.053458] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095536] pid_max: default: 32768 minimum: 301 <6>[ 0.100708] LSM: Security Framework initializing <6>[ 0.105823] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.113643] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.122916] CPU: Testing write buffer coherency: ok <6>[ 0.128281] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.134196] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140672] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147873] rcu: Hierarchical SRCU implementation. <6>[ 0.153713] smp: Bringing up secondary CPUs ... <6>[ 0.158652] smp: Brought up 1 node, 1 CPU <6>[ 0.163101] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169841] CPU: All CPU(s) started in SVC mode. <6>[ 0.175597] devtmpfs: initialized <6>[ 0.191187] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199724] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210166] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218687] pinctrl core: initialized pinctrl subsystem <6>[ 0.226301] NET: Registered protocol family 16 <6>[ 0.233870] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260330] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266409] audit: initializing netlink subsys (disabled) <6>[ 0.273445] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273460] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280070] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.286784] cpuidle: using governor menu <5>[ 1.169337] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.294995] No ATAGs? <6>[ 1.297624] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.322155] Kprobes globally optimized <6>[ 1.335197] iommu: Default domain type: Translated <6>[ 1.342534] vgaarb: loaded <5>[ 1.346099] SCSI subsystem initialized <6>[ 1.351410] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.356794] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.366578] PTP clock support registered <6>[ 1.372158] clocksource: Switched to clocksource dmtimer <5>[ 2.034661] VFS: Disk quotas dquot_6.6.0 <6>[ 2.039075] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.056005] NET: Registered protocol family 2 <6>[ 2.061080] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.069796] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.078758] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.087057] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.094739] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.101662] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.108696] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.116318] NET: Registered protocol family 1 <6>[ 2.122170] RPC: Registered named UNIX socket transport module. <6>[ 2.128545] RPC: Registered udp transport module. <6>[ 2.133676] RPC: Registered tcp transport module. <6>[ 2.138781] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.145705] PCI: CLS 0 bytes, default 64 <6>[ 2.150748] Trying to unpack rootfs image as initramfs... <6>[ 3.132806] Freeing initrd memory: 13792K <6>[ 3.138476] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.148851] Initialise system trusted keyrings <6>[ 3.154321] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.162596] NFS: Registering the id_resolver key type <5>[ 3.168147] Key type id_resolver registered <5>[ 3.172775] Key type id_legacy registered <6>[ 3.177222] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.185198] Key type asymmetric registered <5>[ 3.189692] Asymmetric key parser 'x509' registered <6>[ 3.195035] io scheduler mq-deadline registered <6>[ 3.199964] io scheduler kyber registered <3>[ 3.338768] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.347474] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.456864] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.499043] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.571172] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.579926] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.640152] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.648855] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.666378] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.675060] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.738823] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.747392] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.774483] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.788909] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.799834] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.809275] printk: console [ttyS0] enabled <6>[ 3.809275] printk: console [ttyS0] enabled <6>[ 3.818341] printk: bootconsole [omap8250] disabled <6>[ 3.818341] printk: bootconsole [omap8250] disabled <6>[ 3.842023] brd: module loaded <6>[ 3.854433] loop: module loaded <3>[ 3.859834] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.932199] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.974619] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.984534] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.991186] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.997016] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.004571] cpsw 4a100000.ethernet: Detected MACID = 78:a5:04:e2:4c:3d <6>[ 4.013628] i2c /dev entries driver <5>[ 4.019103] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.026988] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.033527] sdhci: Copyright(c) Pierre Ossman <6>[ 4.038867] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.047197] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.057045] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.065470] Initializing XFRM netlink socket <6>[ 4.070270] NET: Registered protocol family 10 <6>[ 4.076719] Segment Routing with IPv6 <6>[ 4.080761] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.087855] NET: Registered protocol family 17 <6>[ 4.092711] NET: Registered protocol family 15 <5>[ 4.097557] Key type dns_resolver registered <6>[ 4.102767] oprofile: using arm/armv7 <6>[ 4.106807] ThumbEE CPU extension supported. <5>[ 4.111379] Registering SWP/SWPB emulation handler <3>[ 4.116922] omap_voltage_late_init: Voltage driver support not added <3>[ 4.123657] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.132048] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.140740] SmartReflex Class3 initialized <6>[ 4.145792] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.154739] Loading compiled-in X.509 certificates <6>[ 4.179447] OMAP GPIO hardware version 0.1 <4>[ 4.212836] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.226395] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.234909] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.241254] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.251167] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.262586] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.271600] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.276879] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.293184] mmc1: new high speed MMC card at address 0001 <6>[ 4.299940] mmcblk1: mmc1:0001 MMC04G 3.60 GiB <6>[ 4.305500] mmcblk1boot0: mmc1:0001 MMC04G partition 1 2.00 MiB <6>[ 4.312224] mmcblk1boot1: mmc1:0001 MMC04G partition 2 2.00 MiB <6>[ 4.318777] mmcblk1rpmb: mmc1:0001 MMC04G partition 3 128 KiB, chardev (249:0) <6>[ 4.328273] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.342745] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.381500] mmc0: new high speed SDHC card at address 1234 <6>[ 4.388427] mmcblk0: mmc0:1234 SA32G 29.1 GiB <6>[ 4.395834] mmcblk0: p1 <6>[ 4.433694] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 6.522843] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.552166] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.582261] Sending DHCP requests ..., OK <6>[ 13.406438] IP-Config: Got DHCP answer from 192.168.56.254, my address is 192.168.56.135 <6>[ 13.414867] IP-Config: Complete: <6>[ 13.418378] device=eth0, hwaddr=78:a5:04:e2:4c:3d, ipaddr=192.168.56.135, mask=255.255.255.0, gw=192.168.56.254 <6>[ 13.429232] host=192.168.56.135, domain=mayfield.sirena.org.uk, nis-domain=(none) <6>[ 13.437469] bootserver=192.168.56.254, rootserver=192.168.56.254, rootpath= <6>[ 13.437476] nameserver0=192.168.56.254 <6>[ 13.449642] ntpserver0=50.205.244.22, ntpserver1=85.199.214.99 <6>[ 13.458894] Freeing unused kernel memory: 1024K <6>[ 13.472659] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 13.706164] udevd[101]: starting version 3.2.9 <5>[ 13.713323] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.720472] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.728135] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 13.745399] udevd[101]: specified user 'tss' unknown <27>[ 13.750980] udevd[101]: specified group 'tss' unknown <30>[ 13.764502] udevd[102]: starting eudev-3.2.9 <6>[ 14.496339] remoteproc remoteproc0: wkup_m3 is available <4>[ 14.658133] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 14.667336] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 14.762507] usbcore: registered new interface driver usbfs <6>[ 14.768367] usbcore: registered new interface driver hub <6>[ 14.774157] usbcore: registered new device driver usb <4>[ 14.903705] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 14.912879] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 15.113095] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 15.118791] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 15.312596] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 15.321192] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 15.328804] usb usb1: Product: MUSB HDRC host driver <6>[ 15.334084] usb usb1: Manufacturer: Linux 5.10.155-cip21 musb-hcd <6>[ 15.340467] usb usb1: SerialNumber: musb-hdrc.1 <4>[ 15.398261] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 15.507815] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 15.515595] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 15.697055] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 15.713506] hub 1-0:1.0: USB hub found <4>[ 15.723384] at24 2-0055: supply vcc not found, using dummy regulator <3>[ 15.789949] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 15.799082] hub 1-0:1.0: 1 port detected <6>[ 15.816768] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 15.822332] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 15.836663] at24 2-0056: supply vcc not found, using dummy regulator <6>[ 15.853686] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 15.861558] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 15.932925] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 15.949650] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 16.065202] tda998x 0-0070: found TDA19988 <3>[ 16.131685] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 16.573264] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 16.682693] remoteproc remoteproc0: powering up wkup_m3 <4>[ 16.688359] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 16.698239] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 16.704495] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <3>[ 16.758189] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 17.473905] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 17.481337] random: crng init done <6>[ 17.498551] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 17.543924] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 17.582700] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 17.690231] PM: Cannot get wkup_m3_ipc handle <6>[ 17.698405] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 17.972536] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 18.001261] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 18.074456] omap-aes 53500000.aes: will run requests pump with realtime priority <6>[ 18.084061] omap-sham 53100000.sham: will run requests pump with realtime priority <3>[ 18.139482] PM: Cannot get wkup_m3_ipc handle <3>[ 18.166967] PM: Cannot get wkup_m3_ipc handle <3>[ 18.619168] PM: Cannot get wkup_m3_ipc handle <3>[ 18.655792] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-205972/environment . /lava-205972/environment / # /lava-205972/bin/lava-test-runner /lava-205972/0 /lava-205972/bin/lava-test-runner /lava-205972/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-205972/0/tests/0_dmesg + cat uuid + UUID=205972_1.5.2.4.1 <8>[ 19.571984] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.638236] <8>[ 19.698804] <8>[ 19.759367] + set +x <8>[ 19.770514] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-205972/environment / # . /lava-205972/environment/lava-205972/bin/lava-test-runner /lava-205972/1 / # /lava-205972/bin/lava-test-runner /lava-205972/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-205972/1/tests/1_bootrr + cat uuid + UUID=205972_1.5.2.4.5 + <8>[ 20.302567] set +x + export 'PATH=/opt/bootrr/helpers:/lava-205972/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-205972/1/../bin/lava-test-case <8>[ 21.383889] /lava-205972/1/../bin/lava-test-case <8>[ 21.439468] /lava-205972/1/../bin/lava-test-case <8>[ 21.472020] + set +x <8>[ 21.499656] / #