[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 9097460/tftp-deploy-_lezo9tv/kernel/zImage tftp 0x10000000 9097460/tftp-deploy-_lezo9tv/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '9097460/tftp-deploy-_lezo9tv/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 2.4 MiB/s done Bytes transferred = 12452352 (be0200 hex) => tftp 0x14000000 9097460/tftp-deploy-_lezo9tv/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9097460/tftp-deploy-_lezo9tv/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '9097460/tftp-deploy-_lezo9tv/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 2.5 MiB/s done Bytes transferred = 19213436 (1252c7c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9097460/tftp-deploy-_lezo9tv/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9097460/tftp-deploy-_lezo9tv/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '9097460/tftp-deploy-_lezo9tv/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 1.8 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbe0200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19213372 Bytes = 18.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.167-cip26 (KernelCI@build-j1016768-arm-gcc-10-multi-v7-defconfig-kselftest-82249) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Feb 10 10:06:11 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917756K/1048576K available (17408K kernel code, 2654K rwdata, 8120K rodata, 2048K init, 6692K bss, 65284K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56016 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000008] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008097] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.022509] Console: colour dummy device 80x30 <4>[ 0.024412] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032423] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036768] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041179] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.045814] ... CLASSHASH_SIZE: 4096 <4>[ 0.050400] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055098] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059820] ... CHAINHASH_SIZE: 32768 <4>[ 0.064496] memory used by lock dependency info: 4061 kB <4>[ 0.070176] memory used for stack traces: 2112 kB <4>[ 0.075195] per task-struct memory footprint: 1536 bytes <6>[ 0.080931] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.091586] pid_max: default: 32768 minimum: 301 <6>[ 0.096815] LSM: Security Framework initializing <6>[ 0.101380] LSM support for eBPF active <6>[ 0.105538] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.112976] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123568] CPU: Testing write buffer coherency: ok <6>[ 0.126138] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.132358] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141271] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147662] rcu: Hierarchical SRCU implementation. <6>[ 0.159578] EFI services will not be available. <6>[ 0.162825] smp: Bringing up secondary CPUs ... <6>[ 0.169612] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169628] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.181980] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.181996] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.194031] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.194046] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.203255] smp: Brought up 1 node, 4 CPUs <6>[ 0.206921] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.213321] CPU: All CPU(s) started in SVC mode. <6>[ 0.220948] devtmpfs: initialized <6>[ 0.278976] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.286831] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.294274] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.306225] pinctrl core: initialized pinctrl subsystem <6>[ 0.315718] DMI not present or invalid. <6>[ 0.319252] NET: Registered protocol family 16 <6>[ 0.333505] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.347317] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.347869] cpuidle: using governor menu <6>[ 0.356009] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 1.085361] vdd1p1: supplied by regulator-dummy <6>[ 1.118351] vdd3p0: supplied by regulator-dummy <6>[ 1.150923] vdd2p5: supplied by regulator-dummy <6>[ 1.183491] vddarm: supplied by regulator-dummy <6>[ 1.216884] vddpu: supplied by regulator-dummy <6>[ 1.248293] vddsoc: supplied by regulator-dummy <6>[ 2.545872] No ATAGs? <6>[ 2.546785] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.553855] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.579293] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.612535] Serial: AMBA PL011 UART driver <6>[ 2.678012] Kprobes globally optimized <6>[ 2.797939] iommu: Default domain type: Translated <6>[ 2.802651] vgaarb: loaded <5>[ 2.808020] SCSI subsystem initialized <6>[ 2.811756] usbcore: registered new interface driver usbfs <6>[ 2.815233] usbcore: registered new interface driver hub <6>[ 2.820791] usbcore: registered new device driver usb <6>[ 2.833389] i2c i2c-0: IMX I2C adapter registered <6>[ 2.842735] i2c i2c-1: IMX I2C adapter registered <6>[ 2.849497] i2c i2c-2: IMX I2C adapter registered <6>[ 2.856213] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.858618] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.868132] PTP clock support registered <6>[ 2.889714] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.622979] NET: Registered protocol family 2 <6>[ 4.625568] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.635907] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.642006] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.650069] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.658681] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.665176] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.671932] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.678656] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.686519] NET: Registered protocol family 1 <6>[ 4.693191] RPC: Registered named UNIX socket transport module. <6>[ 4.696603] RPC: Registered udp transport module. <6>[ 4.701673] RPC: Registered tcp transport module. <6>[ 4.706508] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.713311] NET: Registered protocol family 44 <6>[ 4.717946] PCI: CLS 0 bytes, default 64 <6>[ 4.724721] Trying to unpack rootfs image as initramfs... <6>[ 7.259261] Freeing initrd memory: 18764K <4>[ 7.261695] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 7.270290] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 7.285500] Initialise system trusted keyrings <6>[ 7.288314] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 7.345719] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 7.352770] NFS: Registering the id_resolver key type <5>[ 7.355456] Key type id_resolver registered <5>[ 7.359822] Key type id_legacy registered <6>[ 7.364563] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 7.371057] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 7.378736] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 7.385400] Key type asymmetric registered <5>[ 7.387621] Asymmetric key parser 'x509' registered <6>[ 7.393131] bounce: pool size: 64 pages <6>[ 7.396905] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 7.404556] io scheduler mq-deadline registered <6>[ 7.409205] io scheduler kyber registered <4>[ 7.414470] test_firmware: interface ready <6>[ 7.597437] mxs-dma 110000.dma-apbh: initialized <4>[ 7.664099] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.671321] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 7.928829] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.953465] SuperH (H)SCI(F) driver initialized <6>[ 7.958432] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.969810] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.976267] printk: console [ttymxc1] enabled <6>[ 7.976267] printk: console [ttymxc1] enabled <6>[ 7.985196] printk: bootconsole [ec_imx21] disabled <6>[ 7.985196] printk: bootconsole [ec_imx21] disabled <6>[ 8.001861] msm_serial: driver initialized <6>[ 8.007311] STMicroelectronics ASC driver initialized <6>[ 8.019249] STM32 USART driver initialized <6>[ 8.046161] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 8.068777] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.077524] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.085918] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.141787] brd: module loaded <6>[ 8.204851] loop: module loaded <6>[ 8.211686] lkdtm: No crash points registered, enable through debugfs <6>[ 8.234246] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 8.242553] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 8.250934] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 8.259415] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 8.267734] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 8.276245] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 8.284357] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 8.296081] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 8.303472] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 8.312629] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 8.327413] scsi host0: ahci-imx <6>[ 8.333409] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 8.399249] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 8.413196] pps pps0: new PPS source ptp0 <6>[ 8.475475] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 8.486473] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 8.491814] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 8.498276] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 8.504030] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 8.532300] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 8.540232] usbcore: registered new interface driver pegasus <6>[ 8.546399] usbcore: registered new interface driver asix <6>[ 8.552294] usbcore: registered new interface driver ax88179_178a <6>[ 8.558824] usbcore: registered new interface driver cdc_ether <6>[ 8.565218] usbcore: registered new interface driver smsc75xx <6>[ 8.571577] usbcore: registered new interface driver smsc95xx <6>[ 8.577762] usbcore: registered new interface driver net1080 <6>[ 8.583916] usbcore: registered new interface driver cdc_subset <6>[ 8.590328] usbcore: registered new interface driver zaurus <6>[ 8.596459] usbcore: registered new interface driver cdc_ncm <6>[ 8.615426] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.622383] ehci-pci: EHCI PCI platform driver <6>[ 8.627285] ehci-platform: EHCI generic platform driver <6>[ 8.633876] ehci-orion: EHCI orion driver <6>[ 8.639107] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.644351] ehci-st: EHCI STMicroelectronics driver <6>[ 8.650462] ehci-exynos: EHCI Exynos driver <6>[ 8.655805] ehci-atmel: EHCI Atmel driver <6>[ 8.661026] tegra-ehci: Tegra EHCI driver <6>[ 8.666230] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.672835] ohci-pci: OHCI PCI platform driver <6>[ 8.677731] ohci-platform: OHCI generic platform driver <6>[ 8.682304] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.684281] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.689267] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.694258] ohci-st: OHCI STMicroelectronics driver <6>[ 8.699962] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.713542] ohci-atmel: OHCI Atmel driver <6>[ 8.721528] usbcore: registered new interface driver usb-storage <6>[ 8.760937] i2c /dev entries driver <6>[ 8.848997] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.855553] sdhci: Copyright(c) Pierre Ossman <6>[ 8.869990] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.883869] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.893706] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.899199] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.907951] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.915205] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.925504] usbcore: registered new interface driver usbhid <6>[ 8.931438] usbhid: USB HID core driver <6>[ 8.944415] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.952823] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.960719] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.969196] IPv4 over IPsec tunneling driver <6>[ 8.979193] NET: Registered protocol family 10 <6>[ 8.990017] Segment Routing with IPv6 <6>[ 8.993224] mmc2: new high speed SDHC card at address 0001 <6>[ 9.000629] NET: Registered protocol family 17 <6>[ 9.004138] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 9.010468] 8021q: 802.1Q VLAN Support v1.8 <5>[ 9.016104] Key type dns_resolver registered <4>[ 9.032973] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 9.034494] ThumbEE CPU extension supported. <4>[ 9.040944] GPT:29296874 != 30965759 <4>[ 9.040973] GPT:Alternate GPT header not at the end of the disk. <4>[ 9.040990] GPT:29296874 != 30965759 <4>[ 9.041012] GPT: Use GNU Parted to correct GPT errors. <5>[ 9.045585] Registering SWP/SWPB emulation handler <6>[ 9.049475] mmcblk2: p1 p2 p3 <5>[ 9.057160] Loading compiled-in X.509 certificates <4>[ 9.305206] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.314113] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.329520] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.372855] imx_usb 2184200.usb: No over current polarity defined <6>[ 9.387521] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 9.393258] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.431227] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 9.452307] hub 1-0:1.0: USB hub found <6>[ 9.456878] hub 1-0:1.0: 1 port detected <3>[ 9.473948] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 9.481654] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 9.490395] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 9.523172] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.532056] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.547442] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.584631] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.593427] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.608766] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.630682] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 9.665985] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.674875] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.690433] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.716312] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 9.880200] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 10.089191] hub 1-1:1.0: USB hub found <6>[ 10.094300] hub 1-1:1.0: 3 ports detected <4>[ 10.130868] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 10.139750] panel-simple panel-lcd: Specify missing connector_type <4>[ 10.155232] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.841668] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 11.870373] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.900071] Sending DHCP requests ., OK <6>[ 11.944610] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 <6>[ 11.953242] IP-Config: Complete: <6>[ 11.956818] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 <6>[ 11.967731] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 11.976779] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 11.976803] nameserver0=192.168.101.1 <6>[ 12.049977] Freeing unused kernel memory: 2048K <6>[ 12.081715] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.541697] udevd[137]: starting version 3.2.9 <5>[ 12.551271] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.559276] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.566467] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 12.590419] udevd[137]: specified user 'tss' unknown <27>[ 12.596075] udevd[137]: specified group 'tss' unknown <30>[ 12.612620] udevd[138]: starting eudev-3.2.9 <6>[ 14.439241] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 14.490450] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.499335] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.553111] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 14.608682] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 14.689346] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.698329] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.735586] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.771904] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.790380] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.799527] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.839974] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 14.849132] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 14.858575] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 14.860107] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.867602] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 14.921107] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.930085] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.945671] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.040279] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.049189] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.168641] CAN device driver interface <4>[ 15.168870] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.330614] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.379930] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.407620] caam 2100000.crypto: Entropy delay = 3200 <6>[ 15.429907] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.436766] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 15.473910] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 15.534674] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.540209] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 15.547127] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 15.555373] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 15.569838] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 15.576254] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 15.601647] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 15.631555] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.640525] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.649323] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.658218] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.758847] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.773799] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.789691] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.950232] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.959032] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.968093] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.976914] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.223724] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 16.224053] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 16.235622] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 16.238062] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.332676] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.363904] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.372819] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.381967] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.390818] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.438321] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.450169] panel-simple panel-lcd: Specify missing connector_type <6>[ 17.230738] caam algorithms registered in /proc/crypto <6>[ 17.242949] caam 2100000.crypto: registering rng-caam <5>[ 17.372299] random: crng init done <5>[ 17.376110] random: 1 urandom warning(s) missed due to ratelimiting <4>[ 17.385731] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 17.426662] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.435572] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.444462] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.453261] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 17.494878] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.503817] panel-simple panel-lcd: Specify missing connector_type <4>[ 17.519689] panel-simple panel-lvds0: supply power not found, using dummy regulator done <6>[ 17.551877] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.560773] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.569750] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) Saving random seed: <6>[ 17.578495] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9097460/environment . /lava-9097460/environment / # /lava-9097460/bin/lava-test-runner /lava-9097460/0 /lava-9097460/bin/lava-test-runner /lava-9097460/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9097460/0/tests/0_dmesg + cat uuid + UUID=9097460_1.5.2.4.1<8>[ 18.819141] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.963486] <8>[ 19.101582] <8>[ 19.227481] + set +x <8>[ 19.239705] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9097460/environment / # . /lava-9097460/environment/lava-9097460/bin/lava-test-runner /lava-9097460/1 / # /lava-9097460/bin/lava-test-runner /lava-9097460/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9097460/1/tests/1_bootrr + cat uuid + UUID=9097460_1.5.2.4.5<8>[ 19.905995] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9097460/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 120000.hdmi /lava-9097460/1/../bin/lava-test-case <8>[ 21.130487] /lava-9097460/1/../bin/lava-test-case <8>[ 21.264644] /lava-9097460/1/../bin/lava-test-case <8>[ 21.336548] + set +x <8>[ 21.386442] / #