Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 6a:4a:cd:5c:0c:dd , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 32:12:77:b5:2e:26 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1199974/tftp-deploy-4v9li3wq/kernel/uImage tftp 0x80080000 1199974/tftp-deploy-4v9li3wq/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1199974/tftp-deploy-4v9li3wq/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 4 MiB/s done Bytes transferred = 31781440 (1e4f240 hex) => tftp 0x91000000 1199974/tftp-deploy-4v9li3wq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1199974/tftp-deploy-4v9li3wq/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1199974/tftp-deploy-4v9li3wq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 2.6 MiB/s done Bytes transferred = 18896919 (1205817 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1199974/tftp-deploy-4v9li3wq/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1199974/tftp-deploy-4v9li3wq/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1199974/tftp-deploy-4v9li3wq/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 1000 Bytes/s done Bytes transferred = 19637 (4cb5 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-13 12:24:07 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 31781376 Bytes = 30.3 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-13 12:24:10 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18896855 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007cb4 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 5.10.177-cip31 (KernelCI@build-j1346595-arm64-gcc-10-defconfig-dt9sn) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Fri Apr 14 09:46:58 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3f8b00-0x837e3fafff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 23 pages/cpu s56664 r8192 d29352 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) [ 0.000000] Memory: 14180288K/14612480K available (14528K kernel code, 2812K rwdata, 7616K rodata, 5952K init, 514K bss, 399424K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080050000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080060000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080070000 [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008280] Console: colour dummy device 80x25 [ 0.012783] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023210] pid_max: default: 32768 minimum: 301 [ 0.027883] LSM: Security Framework initializing [ 0.032596] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.040260] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.048980] rcu: Hierarchical SRCU implementation. [ 0.053908] Platform MSI: gic-its@6020000 domain created [ 0.059298] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.066858] fsl-mc MSI: gic-its@6020000 domain created [ 0.072483] EFI services will not be available. [ 0.077217] smp: Bringing up secondary CPUs ... [ 0.081998] Detected PIPT I-cache on CPU1 [ 0.082016] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.082024] GICv3: CPU1: using allocated LPI pending table @0x0000008080080000 [ 0.082039] arch_timer: CPU1: Trapping CNTVCT access [ 0.082047] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.082310] Detected PIPT I-cache on CPU2 [ 0.082326] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.082333] GICv3: CPU2: using allocated LPI pending table @0x0000008080090000 [ 0.082348] arch_timer: CPU2: Trapping CNTVCT access [ 0.082357] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.082616] Detected PIPT I-cache on CPU3 [ 0.082626] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.082632] GICv3: CPU3: using allocated LPI pending table @0x00000080800a0000 [ 0.082643] arch_timer: CPU3: Trapping CNTVCT access [ 0.082650] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.082898] Detected PIPT I-cache on CPU4 [ 0.082913] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.082921] GICv3: CPU4: using allocated LPI pending table @0x00000080800b0000 [ 0.082936] arch_timer: CPU4: Trapping CNTVCT access [ 0.082944] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.083201] Detected PIPT I-cache on CPU5 [ 0.083212] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.083218] GICv3: CPU5: using allocated LPI pending table @0x00000080800c0000 [ 0.083229] arch_timer: CPU5: Trapping CNTVCT access [ 0.083236] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.083487] Detected PIPT I-cache on CPU6 [ 0.083504] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.083512] GICv3: CPU6: using allocated LPI pending table @0x00000080800d0000 [ 0.083526] arch_timer: CPU6: Trapping CNTVCT access [ 0.083535] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.083788] Detected PIPT I-cache on CPU7 [ 0.083799] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.083806] GICv3: CPU7: using allocated LPI pending table @0x00000080800e0000 [ 0.083817] arch_timer: CPU7: Trapping CNTVCT access [ 0.083824] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.083863] smp: Brought up 1 node, 8 CPUs [ 0.297357] SMP: Total of 8 processors activated. [ 0.302090] CPU features: detected: 32-bit EL0 Support [ 0.307266] CPU features: detected: CRC32 instructions [ 0.312436] CPU features: detected: 32-bit EL1 Support [ 0.329066] CPU: All CPU(s) started at EL2 [ 0.333211] alternatives: patching kernel code [ 0.338369] devtmpfs: initialized [ 0.343013] KASLR enabled [ 0.345715] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.355533] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.362891] pinctrl core: initialized pinctrl subsystem [ 0.368602] DMI not present or invalid. [ 0.372742] NET: Registered protocol family 16 [ 0.377897] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.385380] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.393713] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.401783] audit: initializing netlink subsys (disabled) [ 0.407299] audit: type=2000 audit(0.268:1): state=initialized audit_enabled=0 res=1 [ 0.407646] thermal_sys: Registered thermal governor 'step_wise' [ 0.415090] thermal_sys: Registered thermal governor 'power_allocator' [ 0.421481] cpuidle: using governor menu [ 0.432072] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.438976] ASID allocator initialised with 32768 entries [ 0.444892] Serial: AMBA PL011 UART driver [ 0.456016] Machine: Freescale Layerscape 2088A RDB Board [ 0.461449] SoC family: QorIQ LS2088A [ 0.465124] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.477736] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.484669] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.491410] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.498146] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.505517] cryptd: max_cpu_qlen set to 1000 [ 0.510886] ACPI: Interpreter disabled. [ 0.515382] iommu: Default domain type: Translated [ 0.520378] vgaarb: loaded [ 0.523207] SCSI subsystem initialized [ 0.527114] usbcore: registered new interface driver usbfs [ 0.532643] usbcore: registered new interface driver hub [ 0.537993] usbcore: registered new device driver usb [ 0.543273] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.550648] i2c i2c-0: IMX I2C adapter registered [ 0.555516] pps_core: LinuxPPS API ver. 1 registered [ 0.560505] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.569712] PTP clock support registered [ 0.573719] EDAC MC: Ver: 3.0.0 [ 0.577344] fsl-ifc 2240000.ifc: Freescale Integrated Flash Controller [ 0.583927] fsl-ifc 2240000.ifc: IFC version 2.0, 8 banks [ 0.589425] FPGA manager framework [ 0.592864] Advanced Linux Sound Architecture Driver Initialized. [ 0.599303] clocksource: Switched to clocksource arch_sys_counter [ 0.605510] VFS: Disk quotas dquot_6.6.0 [ 0.609474] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.616459] pnp: PnP ACPI: disabled [ 0.622207] NET: Registered protocol family 2 [ 0.627014] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.638080] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.646848] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.655440] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.663346] TCP: Hash tables configured (established 131072 bind 65536) [ 0.670082] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.677081] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.684577] NET: Registered protocol family 1 [ 0.689142] RPC: Registered named UNIX socket transport module. [ 0.695102] RPC: Registered udp transport module. [ 0.699840] RPC: Registered tcp transport module. [ 0.704567] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.711046] PCI: CLS 0 bytes, default 64 [ 0.715052] Unpacking initramfs... [ 1.169328] Freeing initrd memory: 18448K [ 1.173807] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.181759] kvm [1]: IPA Size Limit: 44 bits [ 1.186513] kvm [1]: vgic-v2@c0e0000 [ 1.190119] kvm [1]: GIC system register CPU interface enabled [ 1.196072] kvm [1]: vgic interrupt IRQ9 [ 1.200118] kvm [1]: Hyp mode initialized successfully [ 1.207147] Initialise system trusted keyrings [ 1.211678] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 1.220415] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.226530] NFS: Registering the id_resolver key type [ 1.231636] Key type id_resolver registered [ 1.235842] Key type id_legacy registered [ 1.239903] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.246645] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.254145] 9p: Installing v9fs 9p2000 file system support [ 1.281251] Key type asymmetric registered [ 1.285369] Asymmetric key parser 'x509' registered [ 1.290283] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.297720] io scheduler mq-deadline registered [ 1.302273] io scheduler kyber registered [ 1.309956] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 1.317323] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 1.325905] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 1.334553] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 1.341296] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.346809] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.353024] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.363624] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.369673] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 1.375976] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 1.382282] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 1.389400] pci 0000:00:00.0: supports D1 D2 [ 1.393691] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.400409] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 1.406517] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 1.413202] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 1.419891] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 1.425532] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 1.432292] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 1.439632] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.455801] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.462979] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.470158] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.477772] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.485035] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.491250] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.498438] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.506051] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.513242] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.520426] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.526565] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.531816] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.537946] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.545285] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.552648] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 1.561238] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 1.569874] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 1.576617] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.582132] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 1.591145] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.601739] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.607792] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 1.614905] pci 0001:00:00.0: supports D1 D2 [ 1.619197] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.626225] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 1.633840] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 1.639602] EINJ: ACPI disabled. [ 1.648177] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.655402] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 16, base_baud = 21875000) is a 16550A [ 1.664460] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 16, base_baud = 21875000) is a 16550A [ 1.673316] printk: console [ttyS1] enabled [ 1.673316] printk: console [ttyS1] enabled [ 1.681697] printk: bootconsole [uart8250] disabled [ 1.681697] printk: bootconsole [uart8250] disabled [ 1.691679] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 17, base_baud = 21875000) is a 16550A [ 1.700672] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 17, base_baud = 21875000) is a 16550A [ 1.709662] SuperH (H)SCI(F) driver initialized [ 1.714387] msm_serial: driver initialized [ 1.719258] arm-smmu 5000000.iommu: probing hardware configuration... [ 1.725700] arm-smmu 5000000.iommu: SMMUv2 with: [ 1.730311] arm-smmu 5000000.iommu: stage 1 translation [ 1.735617] arm-smmu 5000000.iommu: stage 2 translation [ 1.740924] arm-smmu 5000000.iommu: nested translation [ 1.746143] arm-smmu 5000000.iommu: coherent table walk [ 1.751451] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 1.758584] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 1.765108] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 1.771544] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.777979] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.788392] loop: module loaded [ 1.791893] megasas: 07.714.04.00-rc1 [ 1.796025] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 1.803552] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 1.810962] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 1.818674] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.827636] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.837811] scsi host0: ahci-qoriq [ 1.841314] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 104 [ 1.849381] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 1.856909] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 1.864318] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 1.872013] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.880971] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.890879] scsi host1: ahci-qoriq [ 1.894346] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 105 [ 1.902642] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 1.911912] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 1.921999] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.927142] Amd/Fujitsu Extended Query version 1.3. [ 1.932191] number of CFI chips: 1 [ 1.952223] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 1.958578] nand: Micron MT29F16G08ABABAWP [ 1.962674] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 1.971445] Bad block table found at page 524160, version 0x01 [ 1.979196] Bad block table found at page 524032, version 0x01 [ 1.999703] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 2.007699] spi-nor spi0.0: unrecognized JEDEC id bytes: e3 c7 87 0e 1e 3c [ 2.014899] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 2.021788] spi-nor: probe of spi1.0 failed with error -2 [ 2.028282] tun: Universal TUN/TAP device driver, 1.6 [ 2.033624] thunder_xcv, ver 1.0 [ 2.036872] thunder_bgx, ver 1.0 [ 2.040132] nicpf, ver 1.0 [ 2.043281] hclge is initializing [ 2.046603] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 2.053820] hns3: Copyright (c) 2017 Huawei Corporation. [ 2.059140] e1000: Intel(R) PRO/1000 Network Driver [ 2.064014] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 2.069770] e1000e: Intel(R) PRO/1000 Network Driver [ 2.074730] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.080726] e1000e 0000:01:00.0: Adding to iommu group 0 [ 2.086392] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.143748] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.161462] ata1: SATA link down (SStatus 0 SControl 300) [ 2.205230] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 2.213155] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.217456] ata2: SATA link down (SStatus 0 SControl 300) [ 2.220042] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 2.232159] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.237553] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.243138] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 2.249400] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 2.255480] sky2: driver version 1.30 [ 2.259539] VFIO - User Level meta-driver version: 0.3 [ 2.265895] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.272442] ehci-pci: EHCI PCI platform driver [ 2.276896] ehci-platform: EHCI generic platform driver [ 2.282163] ehci-orion: EHCI orion driver [ 2.286203] ehci-exynos: EHCI Exynos driver [ 2.290416] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.296598] ohci-pci: OHCI PCI platform driver [ 2.301049] ohci-platform: OHCI generic platform driver [ 2.306309] ohci-exynos: OHCI Exynos driver [ 2.310657] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.316146] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 2.323887] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.333297] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x03100000 [ 2.339367] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.344851] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 2.352506] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 2.359238] hub 1-0:1.0: USB hub found [ 2.362994] hub 1-0:1.0: 1 port detected [ 2.367033] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.375282] hub 2-0:1.0: USB hub found [ 2.379036] hub 2-0:1.0: 1 port detected [ 2.383090] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.388583] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 2.396309] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.405715] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x03110000 [ 2.411786] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.417270] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 2.424925] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.431613] hub 3-0:1.0: USB hub found [ 2.435367] hub 3-0:1.0: 1 port detected [ 2.439398] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.447641] hub 4-0:1.0: USB hub found [ 2.451398] hub 4-0:1.0: 1 port detected [ 2.455533] usbcore: registered new interface driver usb-storage [ 2.462513] i2c /dev entries driver [ 2.467201] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.575334] rtc-ds3232: probe of 2-0068 failed with error -110 [ 2.581182] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.586102] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.591019] i2c i2c-0: Added multiplexed i2c bus 4 [ 2.595879] i2c i2c-0: Added multiplexed i2c bus 5 [ 2.600734] i2c i2c-0: Added multiplexed i2c bus 6 [ 2.605590] i2c i2c-0: Added multiplexed i2c bus 7 [ 2.610454] i2c i2c-0: Added multiplexed i2c bus 8 [ 2.615244] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 2.623623] sp805-wdt c000000.wdt: registration successful [ 2.629183] sp805-wdt c010000.wdt: registration successful [ 2.634739] sp805-wdt c100000.wdt: registration successful [ 2.640296] sp805-wdt c110000.wdt: registration successful [ 2.645851] sp805-wdt c200000.wdt: registration successful [ 2.651407] sp805-wdt c210000.wdt: registration successful [ 2.656962] sp805-wdt c300000.wdt: registration successful [ 2.662517] sp805-wdt c310000.wdt: registration successful [ 2.669399] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 2.677847] sdhci: Secure Digital Host Controller Interface driver [ 2.684095] sdhci: Copyright(c) Pierre Ossman [ 2.688663] Synopsys Designware Multimedia Card Interface Driver [ 2.695030] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.701498] ledtrig-cpu: registered to indicate activity on CPUs [ 2.708077] usbcore: registered new interface driver usbhid [ 2.713650] usbhid: USB HID core driver [ 2.718654] optee: probing for conduit method. [ 2.723101] optee: api uid mismatch [ 2.726591] optee: probe of firmware:optee failed with error -22 [ 2.726758] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 2.733255] NET: Registered protocol family 17 [ 2.744963] 9pnet: Installing 9P2000 support [ 2.749263] Key type dns_resolver registered [ 2.753663] registered taskstats version 1 [ 2.757760] Loading compiled-in X.509 certificates [ 2.764138] pcieport 0000:00:00.0: Adding to iommu group 1 [ 2.769796] pcieport 0000:00:00.0: PME: Signaling with IRQ 112 [ 2.775738] pcieport 0001:00:00.0: Adding to iommu group 2 [ 2.781371] pcieport 0001:00:00.0: PME: Signaling with IRQ 116 [ 5.300314] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 5.331330] Sending DHCP requests .., OK [ 9.087263] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 9.094847] IP-Config: Complete: [ 9.098082] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 9.108089] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 9.114879] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 9.114884] nameserver0=172.16.1.4 [ 9.125102] ALSA device list: [ 9.128085] No soundcards found. [ 9.133961] Freeing unused kernel memory: 5952K [ 9.143363] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 9.181722] udevd[183]: starting version 3.2.9 [ 9.186494] random: udevd: uninitialized urandom read (16 bytes read) [ 9.193021] random: udevd: uninitialized urandom read (16 bytes read) [ 9.199482] random: udevd: uninitialized urandom read (16 bytes read) [ 9.207948] udevd[183]: specified user 'tss' unknown [ 9.212965] udevd[183]: specified group 'tss' unknown [ 9.218839] udevd[184]: starting eudev-3.2.9 [ 9.308641] lm90 4-004c: supply vcc not found, using dummy regulator [ 9.331760] udevd[209]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 9.340889] udevd[209]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 9.819315] ina2xx 3-0040: error configuring the device: -110 [ 9.819506] lm90 4-004c: Failed to initialize device [ 9.830213] lm90: probe of 4-004c failed with error -11 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 9.896851] NET: Registered protocol family 10 [ 9.902144] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1199974/environment . /lava-1199974/environment / # /lava-1199974/bin/lava-test-runner /lava-1199974/0 /lava-1199974/bin/lava-test-runner /lava-1199974/0 + export 'TESTRUN_[ 10.418582] ID=0_dmesg' + cd /lava-1199974/0/tests/0_dmesg + cat uuid + UUID=1199974_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/[ 10.435342] kernelci/dmesg.sh [ 10.455479] [ 10.475718] + set +x [ 10.484822] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1199974/environment / # . /lava-1199974/environment/lava-1199974/bin/lava-test-runner /lava-1199974/1 / # /lava-1199974/bin/lava-test-runner /lava-1199974/1 + export 'TESTRUN_ID=1_bootrr' + [ 10.921318] cd /lava-1199974/1/tests/1_bootrr + cat uuid + UUID=1199974_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1199974/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 8000000.crypto /lava-1199974/1/../bin/lava-test-case [ 11.939329] /lava-1199974/1/../bin/lava-test-case [ 11.958145] /lava-1199974/1/../bin/lava-test-case [ 11.971460] + set +x [ 11.983198] / #