Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete..... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.111 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 346048/tftp-deploy-f7dqr6ob/kernel/Image tftp 0x82000000 346048/tftp-deploy-f7dqr6ob/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.111; sending through gateway 172.16.0.254 Filename '346048/tftp-deploy-f7dqr6ob/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################## 14.8 MiB/s done Bytes transferred = 43600384 (2994a00 hex) => tftp 0x90080000 346048/tftp-deploy-f7dqr6ob/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 346048/tftp-deploy-f7dqr6ob/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.111; sending through gateway 172.16.0.254 Filename '346048/tftp-deploy-f7dqr6ob/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################### 15.2 MiB/s done Bytes transferred = 21544645 (148bec5 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 346048/tftp-deploy-f7dqr6ob/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 346048/tftp-deploy-f7dqr6ob/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.111; sending through gateway 172.16.0.254 Filename '346048/tftp-deploy-f7dqr6ob/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *## 6 MiB/s done Bytes transferred = 25056 (61e0 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2023-05-28 23:54:19 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 21544581 Bytes = 20.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900091df WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.180-cip33 (KernelCI@build-j1578139-arm64-gcc-10-defconfig-kselftest-tl9vw) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Sun May 28 23:32:14 UTC 2023 [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7db7c0-0x20ff7ddfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 [ 0.000000] percpu: Embedded 34 pages/cpu s101008 r8192 d30064 u139264 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3940348K/4194304K available (18688K kernel code, 4562K rwdata, 9452K rodata, 9728K init, 11274K bss, 221188K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 58557 entries in 229 pages <6>[ 0.000000] ftrace: allocated 229 pages with 5 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080200000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x00000020801e0000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000020801f0000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000003] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008809] Console: colour dummy device 80x25 <4>[ 0.013586] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.021684] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026094] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030592] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035264] ... CLASSHASH_SIZE: 4096 <4>[ 0.039937] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.044698] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049459] ... CHAINHASH_SIZE: 32768 <4>[ 0.054219] memory used by lock dependency info: 6365 kB <4>[ 0.059945] memory used for stack traces: 4224 kB <4>[ 0.065057] per task-struct memory footprint: 1920 bytes <6>[ 0.070864] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.081604] pid_max: default: 32768 minimum: 301 <6>[ 0.086679] LSM: Security Framework initializing <6>[ 0.091649] LSM support for eBPF active <6>[ 0.095873] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.103647] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.115670] rcu: Hierarchical SRCU implementation. <6>[ 0.123255] Platform MSI: gic-its@6020000 domain created <6>[ 0.129138] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.137084] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.143183] EFI services will not be available. <6>[ 0.148451] smp: Bringing up secondary CPUs ... <6>[ 0.154642] Detected PIPT I-cache on CPU1 <6>[ 0.154665] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.154674] GICv3: CPU1: using allocated LPI pending table @0x0000002080280000 <6>[ 0.154717] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.155121] smp: Brought up 1 node, 2 CPUs <6>[ 0.185557] SMP: Total of 2 processors activated. <6>[ 0.190597] CPU features: detected: 32-bit EL0 Support <6>[ 0.196131] CPU features: detected: CRC32 instructions <6>[ 0.201620] CPU features: detected: 32-bit EL1 Support <6>[ 0.235573] CPU: All CPU(s) started at EL2 <6>[ 0.240048] alternatives: patching kernel code <6>[ 0.246814] devtmpfs: initialized <4>[ 0.263885] KASLR disabled due to lack of seed <6>[ 0.269773] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.279921] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.288092] pinctrl core: initialized pinctrl subsystem <6>[ 0.296373] DMI not present or invalid. <6>[ 0.301524] NET: Registered protocol family 16 <6>[ 0.309424] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.316981] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.325507] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.333900] audit: initializing netlink subsys (disabled) <5>[ 0.339949] audit: type=2000 audit(0.228:1): state=initialized audit_enabled=0 res=1 <6>[ 0.341984] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.348073] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.355219] cpuidle: using governor menu <6>[ 0.366644] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.373871] ASID allocator initialised with 65536 entries <6>[ 0.382030] Serial: AMBA PL011 UART driver <6>[ 0.437371] Machine: Kontron KBox A-230-LS <6>[ 0.441801] SoC family: QorIQ LS1028A <6>[ 0.445764] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.490677] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.497753] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.504810] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.511860] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.521944] cryptd: max_cpu_qlen set to 1000 <6>[ 0.532014] ACPI: Interpreter disabled. <6>[ 0.540210] iommu: Default domain type: Translated <6>[ 0.546011] vgaarb: loaded <5>[ 0.549826] SCSI subsystem initialized <6>[ 0.554723] usbcore: registered new interface driver usbfs <6>[ 0.560657] usbcore: registered new interface driver hub <6>[ 0.566371] usbcore: registered new device driver usb <6>[ 0.572762] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.581928] i2c i2c-0: IMX I2C adapter registered <6>[ 0.588047] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.596305] i2c i2c-1: IMX I2C adapter registered <6>[ 0.601739] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.609884] i2c i2c-2: IMX I2C adapter registered <6>[ 0.615606] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.620947] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.630481] PTP clock support registered <6>[ 0.634985] EDAC MC: Ver: 3.0.0 <6>[ 0.641469] FPGA manager framework <6>[ 0.645435] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.653599] clocksource: Switched to clocksource arch_sys_counter <5>[ 1.392108] VFS: Disk quotas dquot_6.6.0 <6>[ 1.396458] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 1.404310] pnp: PnP ACPI: disabled <6>[ 1.424432] NET: Registered protocol family 2 <6>[ 1.429494] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.439627] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 163840 bytes, linear) <6>[ 1.448931] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.457859] TCP bind hash table entries: 32768 (order: 9, 2359296 bytes, linear) <6>[ 1.470150] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.477716] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.486283] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.494219] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.502595] NET: Registered protocol family 1 <6>[ 1.508480] RPC: Registered named UNIX socket transport module. <6>[ 1.514778] RPC: Registered udp transport module. <6>[ 1.519815] RPC: Registered tcp transport module. <6>[ 1.524850] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.531651] NET: Registered protocol family 44 <6>[ 1.536440] PCI: CLS 0 bytes, default 64 <6>[ 1.541175] Unpacking initramfs... <6>[ 2.693191] Freeing initrd memory: 21032K <6>[ 2.698407] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 2.707272] kvm [1]: IPA Size Limit: 44 bits <6>[ 2.718294] kvm [1]: GICv3: no GICV resource entry <6>[ 2.723424] kvm [1]: disabling GICv2 emulation <6>[ 2.728228] kvm [1]: GIC system register CPU interface enabled <6>[ 2.734522] kvm [1]: vgic interrupt IRQ9 <6>[ 2.738926] kvm [1]: Hyp mode initialized successfully <5>[ 2.749095] Initialise system trusted keyrings <6>[ 2.754259] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 2.785510] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.793202] NFS: Registering the id_resolver key type <5>[ 2.798655] Key type id_resolver registered <5>[ 2.803182] Key type id_legacy registered <6>[ 2.807769] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.814848] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.822924] 9p: Installing v9fs 9p2000 file system support <5>[ 2.859513] Key type asymmetric registered <5>[ 2.863983] Asymmetric key parser 'x509' registered <6>[ 2.869262] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 2.877036] io scheduler mq-deadline registered <6>[ 2.881898] io scheduler kyber registered <4>[ 2.886602] test_firmware: interface ready <6>[ 2.911353] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 2.919549] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 2.928785] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 2.938008] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 2.947231] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 2.956452] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 2.965674] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 2.974866] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 2.984227] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 2.993649] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 3.000987] pci_bus 0000:00: root bus resource [bus 00] <6>[ 3.006555] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 3.017298] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 3.028480] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 3.039224] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 3.050413] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 3.061155] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 3.072335] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 3.083160] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 3.089698] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.100535] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.111826] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 3.122927] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 3.134541] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 3.140422] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 3.150725] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 3.162140] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 3.168638] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.179483] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.190757] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 3.201856] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 3.213467] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 3.219338] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 3.229640] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 3.241027] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 3.247497] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.258334] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.269676] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 3.276025] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 3.282519] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.293354] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.304703] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 3.311073] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 3.317543] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.328389] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.339730] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 3.346115] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 3.352588] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.363432] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.374706] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.385625] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 3.392037] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 3.398508] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.409343] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.420685] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 3.427808] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 3.434385] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 3.442832] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 3.450926] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 3.459238] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 3.467018] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 3.475998] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 3.485235] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.492308] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.498138] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.504670] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.515634] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.522181] pci 0001:00:00.0: supports D1 D2 <6>[ 3.526779] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.535134] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.542129] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.548022] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.555785] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.564723] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.573946] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.581008] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.586837] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.596177] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.607138] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.613710] pci 0002:00:00.0: supports D1 D2 <6>[ 3.618308] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.626634] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.633612] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 3.642371] EINJ: ACPI disabled. <6>[ 3.676861] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.690785] printk: console [ttyS0] disabled <6>[ 3.695599] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 3.704962] printk: console [ttyS0] enabled <6>[ 3.704962] printk: console [ttyS0] enabled <6>[ 3.713946] printk: bootconsole [ns16550a0] disabled <6>[ 3.713946] printk: bootconsole [ns16550a0] disabled <6>[ 3.726405] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 3.736642] SuperH (H)SCI(F) driver initialized <6>[ 3.742465] msm_serial: driver initialized <6>[ 3.748026] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 3.763195] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.769972] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.774893] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.780511] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.786127] arm-smmu 5000000.iommu: nested translation <5>[ 3.791664] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.799128] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.805972] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.812723] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.819474] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 3.848442] loop: module loaded <6>[ 3.853059] lkdtm: No crash points registered, enable through debugfs <6>[ 3.882395] megasas: 07.714.04.00-rc1 <6>[ 3.896839] spi-nor spi0.0: w25q32dw (4096 Kbytes) <5>[ 3.915495] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 3.922663] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 3.928202] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 3.940009] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 3.951779] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 3.963778] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 3.975765] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 3.987765] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 3.999775] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.011754] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.032213] thunder_xcv, ver 1.0 <6>[ 4.035858] thunder_bgx, ver 1.0 <6>[ 4.039496] nicpf, ver 1.0 <6>[ 4.044545] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 4.157647] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.164285] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 06:99:0d:79:e7:6d <6>[ 4.173141] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using ea:37:16:af:51:57 <6>[ 4.203556] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 4.317641] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 4.324243] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using b6:77:8e:d1:d3:ad <6>[ 4.333099] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using 16:63:4d:2b:52:ae <6>[ 4.362964] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 4.473641] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 4.480245] fsl_enetc 0000:00:00.2: no MAC address specified for SI0, using 82:6f:5a:75:c2:c9 <6>[ 4.492596] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 4.605648] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 4.613097] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 4.619974] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 4.733642] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.792440] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 4.798987] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.806270] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.815677] pps pps0: new PPS source ptp0 <6>[ 4.821663] hclge is initializing <6>[ 4.825336] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.832891] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.838648] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.843831] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.850005] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.855274] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.861663] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.867382] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.873348] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.879924] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.886969] sky2: driver version 1.30 <6>[ 4.893351] VFIO - User Level meta-driver version: 0.3 <6>[ 4.900074] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 4.907643] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 4.917906] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.924794] ehci-pci: EHCI PCI platform driver <6>[ 4.929656] ehci-platform: EHCI generic platform driver <6>[ 4.935452] ehci-orion: EHCI orion driver <6>[ 4.939998] ehci-exynos: EHCI Exynos driver <6>[ 4.944713] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.951237] ohci-pci: OHCI PCI platform driver <6>[ 4.956071] ohci-platform: OHCI generic platform driver <6>[ 4.961866] ohci-exynos: OHCI Exynos driver <6>[ 4.967320] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.973266] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.981629] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 4.991436] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 4.998228] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.004040] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 5.012028] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.020834] hub 1-0:1.0: USB hub found <6>[ 5.025021] hub 1-0:1.0: 1 port detected <6>[ 5.030421] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.040183] hub 2-0:1.0: USB hub found <6>[ 5.044314] hub 2-0:1.0: 1 port detected <6>[ 5.049565] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 5.055510] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 5.063846] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 5.073674] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 5.080493] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 5.086325] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 5.094316] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.102544] hub 3-0:1.0: USB hub found <6>[ 5.106665] hub 3-0:1.0: 1 port detected <6>[ 5.111763] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.121447] hub 4-0:1.0: USB hub found <6>[ 5.125572] hub 4-0:1.0: 1 port detected <6>[ 5.131130] usbcore: registered new interface driver usb-storage <6>[ 5.143693] i2c /dev entries driver <6>[ 5.159038] sp805-wdt c000000.watchdog: registration successful <6>[ 5.165792] sp805-wdt c010000.watchdog: registration successful <6>[ 5.177284] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 5.188403] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.194918] sdhci: Copyright(c) Pierre Ossman <6>[ 5.200807] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.209315] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.216908] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 5.219410] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 5.228933] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.239395] usbcore: registered new interface driver usbhid <6>[ 5.245434] usbhid: USB HID core driver <6>[ 5.249775] mmc0: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 5.257089] mmc1: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 5.261956] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.271498] IPv4 over IPsec tunneling driver <6>[ 5.278324] NET: Registered protocol family 10 <6>[ 5.286174] Segment Routing with IPv6 <6>[ 5.292784] NET: Registered protocol family 17 <6>[ 5.298174] 9pnet: Installing 9P2000 support <5>[ 5.303188] Key type dns_resolver registered <6>[ 5.308551] registered taskstats version 1 <5>[ 5.313047] Loading compiled-in X.509 certificates <6>[ 5.335830] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 5.348532] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 5.355283] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 5.362297] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 5.369036] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 5.386934] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.393683] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 5.410052] mmc1: new HS400 MMC card at address 0001 <6>[ 5.417037] mmcblk1: mmc1:0001 S0J58X 29.6 GiB <6>[ 5.422557] mmcblk1boot0: mmc1:0001 S0J58X partition 1 31.5 MiB <6>[ 5.429262] mmcblk1boot1: mmc1:0001 S0J58X partition 2 31.5 MiB <6>[ 5.436249] mmcblk1rpmb: mmc1:0001 S0J58X partition 3 4.00 MiB, chardev (234:0) <6>[ 5.447217] mmcblk1: p1 p2 p3 <6>[ 5.448156] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.470720] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.508200] fsl_enetc 0000:00:00.1 eth1: PHY [0000:00:00.1:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.528118] fsl_enetc 0000:00:00.1 eth1: configuring for phy/rgmii-id link mode <6>[ 5.543749] fsl_enetc 0000:00:00.2 eth2: configuring for fixed/internal link mode <6>[ 5.551619] fsl_enetc 0000:00:00.2 eth2: Link is Up - 1Gbps/Full - flow control off <5>[ 5.570191] Sending DHCP requests . <6>[ 5.614305] hub 3-1:1.0: USB hub found <6>[ 5.622926] hub 3-1:1.0: 7 ports detected <6>[ 5.973800] usb 3-1.6: new full-speed USB device number 3 using xhci-hcd <3>[ 6.133927] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <4>[ 7.729805] . <6>[ 8.551838] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 8.562346] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <4>[ 11.505776] ., OK <6>[ 11.524249] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.111 <6>[ 11.532502] IP-Config: Complete: <6>[ 11.536163] device=eth0, hwaddr=00:a0:a5:5c:6c:72, ipaddr=172.16.0.111, mask=255.255.255.0, gw=172.16.0.254 <6>[ 11.546793] host=172.16.0.111, domain=lava.lan, nis-domain=(none) <6>[ 11.553755] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 11.553793] nameserver0=8.8.8.8 <6>[ 11.594101] fsl_enetc 0000:00:00.2 eth2: Link is Down <6>[ 11.616296] ALSA device list: <6>[ 11.619790] No soundcards found. <6>[ 11.655617] Freeing unused kernel memory: 9728K <6>[ 11.660813] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.824590] udevd[135]: starting version 3.2.9 <5>[ 11.831275] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.838728] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.845726] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 11.858374] udevd[135]: specified user 'tss' unknown <27>[ 11.863849] udevd[135]: specified group 'tss' unknown <30>[ 11.872575] udevd[136]: starting eudev-3.2.9 <6>[ 12.702499] mali-dp f080000.display: Adding to iommu group 13 <6>[ 12.812049] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth1 <27>[ 12.883102] udevd[146]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 12.892626] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth2 <6>[ 12.928364] mscc_felix 0000:00:00.5: Adding to iommu group 14 <28>[ 12.937768] udevd[146]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <4>[ 12.964820] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 12.971578] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 12.993031] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <4>[ 13.004736] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 13.040174] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 13.048553] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 13.056371] rtc-rv8803 0-0032: registered as rtc0 <4>[ 13.134594] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 13.151457] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 <4>[ 13.158928] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 13.170095] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 <6>[ 13.178358] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 <6>[ 13.186773] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 <3>[ 13.199505] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 13.217820] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 13.248616] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 13.255606] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:07] driver [Generic PHY] (irq=POLL) <6>[ 13.264817] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 13.291126] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 13.297276] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:08] driver [Generic PHY] (irq=POLL) <6>[ 13.331870] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:09] driver [Generic PHY] (irq=POLL) <6>[ 13.354944] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:0a] driver [Generic PHY] (irq=POLL) <6>[ 13.390091] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 13.431121] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control off <6>[ 13.440630] device enp0s0f2 entered promiscuous mode <6>[ 13.462150] DSA: tree 0 setup <6>[ 13.540409] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 13.562298] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 13.817898] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 13.835880] caam algorithms registered in /proc/crypto <6>[ 13.844801] caam 8000000.crypto: registering rng-caam <6>[ 13.871199] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 13.878627] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 13.885540] caam_jr 8040000.jr: Adding to iommu group 18 <5>[ 13.891042] random: crng init done <5>[ 13.895206] random: 2 urandom warning(s) missed due to ratelimiting done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-346048/environment . /lava-346048/environment / # /lava-346048/bin/lava-test-runner /lava-346048/0 /lava-346048/bin/lava-test-runner /lava-346048/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-346048/0/tests/0_dmesg + cat uuid + UUID=346048_1.5.<8>[ 14.696269] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.747480] <8>[ 14.798907] <8>[ 14.855855] + set +x<8>[ 14.870084] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-346048/environment / # . /lava-346048/environment/lava-346048/bin/lava-test-runner /lava-346048/1 / # /lava-346048/bin/lava-test-runner /lava-346048/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-346048/1/tests/1_bootrr + cat uuid + UUID=346048_1.<8>[ 15.388604] 5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-346048/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-346048/1/../bin/lava-test-case <8>[ 15.449050] /lava-346048/1/../bin/lava-test-case <8>[ 15.495355] /lava-346048/1/../bin/lava-test-case <8>[ 15.525896] /lava-346048/1/../bin/lava-test-case <8>[ 15.587664] /lava-346048/1/../bin/lava-test-case <8>[ 15.635369] /lava-346048/1/../bin/lava-test-case <8>[ 15.673289] /lava-346048/1/../bin/lava-test-case <8>[ 15.724877] /lava-346048/1/../bin/lava-test-case <8>[ 15.763992] /lava-346048/1/../bin/lava-test-case <8>[ 15.813861] /lava-346048/1/../bin/lava-test-case <8>[ 15.851452] /lava-346048/1/../bin/lava-test-case <8>[ 15.898883] /lava-346048/1/../bin/lava-test-case <8>[ 15.954798] /lava-346048/1/../bin/lava-test-case <8>[ 16.003880] /lava-346048/1/../bin/lava-test-case <8>[ 16.051312] /lava-346048/1/../bin/lava-test-case <8>[ 16.089574] /lava-346048/1/../bin/lava-test-case <8>[ 16.139594] /lava-346048/1/../bin/lava-test-case <8>[ 16.192569] /lava-346048/1/../bin/lava-test-case <8>[ 16.241329] /lava-346048/1/../bin/lava-test-case <8>[ 16.279785] /lava-346048/1/../bin/lava-test-case <8>[ 16.330111] /lava-346048/1/../bin/lava-test-case <8>[ 16.367116] /lava-346048/1/../bin/lava-test-case <8>[ 16.415749] /lava-346048/1/../bin/lava-test-case <8>[ 16.463997] /lava-346048/1/../bin/lava-test-case <8>[ 16.512128] /lava-346048/1/../bin/lava-test-case <8>[ 16.549530] /lava-346048/1/../bin/lava-test-case <8>[ 16.600501] /lava-346048/1/../bin/lava-test-case <8>[ 16.637841] /lava-346048/1/../bin/lava-test-case <8>[ 16.688463] /lava-346048/1/../bin/lava-test-case <8>[ 16.727773] /lava-346048/1/../bin/lava-test-case <8>[ 16.777886] /lava-346048/1/../bin/lava-test-case <8>[ 16.827909] /lava-346048/1/../bin/lava-test-case <8>[ 16.865264] /lava-346048/1/../bin/lava-test-case <8>[ 16.914308] /lava-346048/1/../bin/lava-test-case <8>[ 16.974112] /lava-346048/1/../bin/lava-test-case <8>[ 17.011683] /lava-346048/1/../bin/lava-test-case <8>[ 17.060232] /lava-346048/1/../bin/lava-test-case <8>[ 17.099296] /lava-346048/1/../bin/lava-test-case <8>[ 17.147821] /lava-346048/1/../bin/lava-test-case <8>[ 17.185274] /lava-346048/1/../bin/lava-test-case <8>[ 17.238158] /lava-346048/1/../bin/lava-test-case <8>[ 17.289845] /lava-346048/1/../bin/lava-test-case <8>[ 17.327691] /lava-346048/1/../bin/lava-test-case <8>[ 17.375797] /lava-346048/1/../bin/lava-test-case <8>[ 17.424812] /lava-346048/1/../bin/lava-test-case <8>[ 17.463627] /lava-346048/1/../bin/lava-test-case <8>[ 17.514228] /lava-346048/1/../bin/lava-test-case <8>[ 17.562471] /lava-346048/1/../bin/lava-test-case <8>[ 17.602045] /lava-346048/1/../bin/lava-test-case <8>[ 17.649915] /lava-346048/1/../bin/lava-test-case <8>[ 17.686712] /lava-346048/1/../bin/lava-test-case <8>[ 17.738001] /lava-346048/1/../bin/lava-test-case <8>[ 17.775061] /lava-346048/1/../bin/lava-test-case <8>[ 17.824554] /lava-346048/1/../bin/lava-test-case <8>[ 17.875763] /lava-346048/1/../bin/lava-test-case <8>[ 17.924391] /lava-346048/1/../bin/lava-test-case <8>[ 17.975493] /lava-346048/1/../bin/lava-test-case <8>[ 18.013572] /lava-346048/1/../bin/lava-test-case <8>[ 18.064093] /lava-346048/1/../bin/lava-test-case <8>[ 18.115735] /lava-346048/1/../bin/lava-test-case <8>[ 18.157244] /lava-346048/1/../bin/lava-test-case <8>[ 18.210252] /lava-346048/1/../bin/lava-test-case <8>[ 18.247759] /lava-346048/1/../bin/lava-test-case <8>[ 18.300395] /lava-346048/1/../bin/lava-test-case <8>[ 19.347450] /lava-346048/1/../bin/lava-test-case <8>[ 20.392085] /lava-346048/1/../bin/lava-test-case <8>[ 21.435993] /lava-346048/1/../bin/lava-test-case <8>[ 22.483498] /lava-346048/1/../bin/lava-test-case <8>[ 22.522561] /lava-346048/1/../bin/lava-test-case <8>[ 22.571598] /lava-346048/1/../bin/lava-test-case <8>[ 22.609768] /lava-346048/1/../bin/lava-test-case <8>[ 22.660161] /lava-346048/1/../bin/lava-test-case <8>[ 22.700217] /lava-346048/1/../bin/lava-test-case <8>[ 22.752599] /lava-346048/1/../bin/lava-test-case <8>[ 22.791302] /lava-346048/1/../bin/lava-test-case <8>[ 22.840948] /lava-346048/1/../bin/lava-test-case <8>[ 22.891022] /lava-346048/1/../bin/lava-test-case <8>[ 22.929344] /lava-346048/1/../bin/lava-test-case <8>[ 22.980854] /lava-346048/1/../bin/lava-test-case <8>[ 23.030171] /lava-346048/1/../bin/lava-test-case <8>[ 23.078782] /lava-346048/1/../bin/lava-test-case <8>[ 23.130198] /lava-346048/1/../bin/lava-test-case <8>[ 23.167987] /lava-346048/1/../bin/lava-test-case <8>[ 23.218346] /lava-346048/1/../bin/lava-test-case <8>[ 23.255395] /lava-346048/1/../bin/lava-test-case <8>[ 23.303440] /lava-346048/1/../bin/lava-test-case <8>[ 23.343259] /lava-346048/1/../bin/lava-test-case <8>[ 23.392126] /lava-346048/1/../bin/lava-test-case <8>[ 23.439141] /lava-346048/1/../bin/lava-test-case <8>[ 23.477441] /lava-346048/1/../bin/lava-test-case <8>[ 23.527175] /lava-346048/1/../bin/lava-test-case <8>[ 24.571198] /lava-346048/1/../bin/lava-test-case <8>[ 25.619305] + set +x<8>[ 25.640459] / # <0>��