[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10604077/tftp-deploy-k_nezqf3/kernel/zImage tftp 0x10000000 10604077/tftp-deploy-k_nezqf3/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10604077/tftp-deploy-k_nezqf3/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.6 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 10604077/tftp-deploy-k_nezqf3/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10604077/tftp-deploy-k_nezqf3/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10604077/tftp-deploy-k_nezqf3/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 11.1 MiB/s done Bytes transferred = 12143231 (b94a7f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10604077/tftp-deploy-k_nezqf3/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10604077/tftp-deploy-k_nezqf3/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10604077/tftp-deploy-k_nezqf3/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10604077/extract-nfsrootfs-jss2mz5i,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10604077/extract-nfsrootfs-jss2mz5i,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12143167 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.180-cip34 (KernelCI@build-j1614509-arm-gcc-10-multi-v7-defconfig-lhmwp) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jun 6 09:43:23 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10604077/extract-nfsrootfs-jss2mz5i,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936500K/1048576K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 46540K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000027] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003880] Console: colour dummy device 80x30 [ 0.003932] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003950] pid_max: default: 32768 minimum: 301 [ 0.004128] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004151] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004798] CPU: Testing write buffer coherency: ok [ 0.004838] CPU0: Spectre v2: using BPIALL workaround [ 0.005098] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005822] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007425] rcu: Hierarchical SRCU implementation. [ 0.011040] EFI services will not be available. [ 0.011352] smp: Bringing up secondary CPUs ... [ 0.012166] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012174] CPU1: Spectre v2: using BPIALL workaround [ 0.013094] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013102] CPU2: Spectre v2: using BPIALL workaround [ 0.014006] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014013] CPU3: Spectre v2: using BPIALL workaround [ 0.014136] smp: Brought up 1 node, 4 CPUs [ 0.014150] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014158] CPU: All CPU(s) started in SVC mode. [ 0.014740] devtmpfs: initialized [ 0.022283] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022523] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022547] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025660] pinctrl core: initialized pinctrl subsystem [ 0.027497] DMI not present or invalid. [ 0.028343] NET: Registered protocol family 16 [ 0.031803] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034127] thermal_sys: Registered thermal governor 'step_wise' [ 0.034317] cpuidle: using governor menu [ 0.034506] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.210339] vdd1p1: supplied by regulator-dummy [ 0.217582] vdd3p0: supplied by regulator-dummy [ 0.224816] vdd2p5: supplied by regulator-dummy [ 0.232026] vddarm: supplied by regulator-dummy [ 0.239359] vddpu: supplied by regulator-dummy [ 0.246418] vddsoc: supplied by regulator-dummy [ 0.576994] No ATAGs? [ 0.577150] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.577162] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.581300] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.587392] Serial: AMBA PL011 UART driver [ 0.590056] printk: console [ramoops-1] enabled [ 0.590278] pstore: Registered ramoops as persistent store backend [ 0.590293] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.622584] iommu: Default domain type: Translated [ 0.623023] vgaarb: loaded [ 0.623926] SCSI subsystem initialized [ 0.624531] usbcore: registered new interface driver usbfs [ 0.624591] usbcore: registered new interface driver hub [ 0.624640] usbcore: registered new device driver usb [ 0.626185] i2c i2c-0: IMX I2C adapter registered [ 0.627535] i2c i2c-1: IMX I2C adapter registered [ 0.628371] i2c i2c-2: IMX I2C adapter registered [ 0.629828] pps_core: LinuxPPS API ver. 1 registered [ 0.629842] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.629874] PTP clock support registered [ 0.633728] clocksource: Switched to clocksource mxc_timer1 [ 1.702370] NET: Registered protocol family 2 [ 1.702825] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.704090] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.704137] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.704227] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.704377] TCP: Hash tables configured (established 8192 bind 8192) [ 1.704594] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.704647] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.704834] NET: Registered protocol family 1 [ 1.705463] RPC: Registered named UNIX socket transport module. [ 1.705479] RPC: Registered udp transport module. [ 1.705489] RPC: Registered tcp transport module. [ 1.705500] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.705517] PCI: CLS 0 bytes, default 64 [ 1.706003] Trying to unpack rootfs image as initramfs... [ 2.667002] Freeing initrd memory: 11860K [ 2.667447] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.667819] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.669676] Initialise system trusted keyrings [ 2.670063] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.676030] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.676778] NFS: Registering the id_resolver key type [ 2.676864] Key type id_resolver registered [ 2.676877] Key type id_legacy registered [ 2.676985] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.677000] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.677041] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.677512] Key type asymmetric registered [ 2.677529] Asymmetric key parser 'x509' registered [ 2.677592] bounce: pool size: 64 pages [ 2.677643] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.677659] io scheduler mq-deadline registered [ 2.677672] io scheduler kyber registered [ 2.717437] mxs-dma 110000.dma-apbh: initialized [ 2.722200] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.722223] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.782681] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.787212] SuperH (H)SCI(F) driver initialized [ 2.788223] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.789226] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 3.617577] printk: console [ttymxc1] enabled [ 3.623360] msm_serial: driver initialized [ 3.627771] STMicroelectronics ASC driver initialized [ 3.634828] STM32 USART driver initialized [ 3.649986] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.657662] panel-simple panel-lcd: Specify missing connector_type [ 3.664231] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.680857] brd: module loaded [ 3.693973] loop: module loaded [ 3.701034] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 3.708992] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 3.717018] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 3.725231] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 3.732972] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 3.740468] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 3.747785] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 3.758107] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 3.765137] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.773965] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.784523] scsi host0: ahci-imx [ 3.788128] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 3.808453] CAN device driver interface [ 3.813673] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.822932] pps pps0: new PPS source ptp0 [ 3.845341] fec 2188000.ethernet eth0: registered PHC device 0 [ 3.852686] e1000e: Intel(R) PRO/1000 Network Driver [ 3.857683] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.863683] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.869089] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.880833] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.888303] usbcore: registered new interface driver pegasus [ 3.894029] usbcore: registered new interface driver asix [ 3.899466] usbcore: registered new interface driver ax88179_178a [ 3.905617] usbcore: registered new interface driver cdc_ether [ 3.911500] usbcore: registered new interface driver smsc75xx [ 3.917322] usbcore: registered new interface driver smsc95xx [ 3.923108] usbcore: registered new interface driver net1080 [ 3.928822] usbcore: registered new interface driver cdc_subset [ 3.934797] usbcore: registered new interface driver zaurus [ 3.940444] usbcore: registered new interface driver cdc_ncm [ 3.949693] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.956251] ehci-pci: EHCI PCI platform driver [ 3.960739] ehci-platform: EHCI generic platform driver [ 3.966291] ehci-orion: EHCI orion driver [ 3.970524] SPEAr-ehci: EHCI SPEAr driver [ 3.974753] ehci-st: EHCI STMicroelectronics driver [ 3.979822] ehci-exynos: EHCI Exynos driver [ 3.984214] ehci-atmel: EHCI Atmel driver [ 3.988407] tegra-ehci: Tegra EHCI driver [ 3.992642] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.998861] ohci-pci: OHCI PCI platform driver [ 4.003354] ohci-platform: OHCI generic platform driver [ 4.008874] SPEAr-ohci: OHCI SPEAr driver [ 4.013078] ohci-st: OHCI STMicroelectronics driver [ 4.018179] ohci-atmel: OHCI Atmel driver [ 4.023431] usbcore: registered new interface driver usb-storage [ 4.037698] i2c /dev entries driver [ 4.060683] sdhci: Secure Digital Host Controller Interface driver [ 4.066895] sdhci: Copyright(c) Pierre Ossman [ 4.074015] Synopsys Designware Multimedia Card Interface Driver [ 4.081969] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.089791] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 4.093174] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 4.094841] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 4.104984] ledtrig-cpu: registered to indicate activity on CPUs [ 4.112059] usbcore: registered new interface driver usbhid [ 4.117677] usbhid: USB HID core driver [ 4.128199] NET: Registered protocol family 10 [ 4.131655] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 4.140014] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 4.140153] Segment Routing with IPv6 [ 4.145575] ata1: SATA link down (SStatus 0 SControl 300) [ 4.145624] ahci-imx 2200000.sata: no device found, disabling link. [ 4.145632] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 4.169521] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.176065] NET: Registered protocol family 17 [ 4.180529] can: controller area network core [ 4.182101] mmc2: new high speed SDHC card at address 0001 [ 4.184994] NET: Registered protocol family 29 [ 4.191294] mmcblk2: mmc2:0001 SD 14.6 GiB [ 4.194886] can: raw protocol [ 4.202052] can: broadcast manager protocol [ 4.206276] can: netlink gateway - max_hops=1 [ 4.211139] Key type dns_resolver registered [ 4.217532] ThumbEE CPU extension supported. [ 4.221823] Registering SWP/SWPB emulation handler [ 4.227261] Loading compiled-in X.509 certificates [ 4.237325] pstore: Using crash dump compression: deflate [ 4.244512] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.251933] GPT:29296874 != 30560255 [ 4.255566] GPT:Alternate GPT header not at the end of the disk. [ 4.261590] GPT:29296874 != 30560255 [ 4.264322] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.265187] GPT: Use GNU Parted to correct GPT errors. [ 4.272803] panel-simple panel-lcd: Specify missing connector_type [ 4.277856] mmcblk2: p1 p2 p3 [ 4.285512] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.303395] imx_usb 2184200.usb: No over current polarity defined [ 4.313055] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 4.318018] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 4.353691] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 4.360466] hub 1-0:1.0: USB hub found [ 4.364347] hub 1-0:1.0: 1 port detected [ 4.370711] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 4.386525] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.394177] panel-simple panel-lcd: Specify missing connector_type [ 4.401789] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.413718] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.421327] panel-simple panel-lcd: Specify missing connector_type [ 4.428924] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.438644] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.450527] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.458208] panel-simple panel-lcd: Specify missing connector_type [ 4.465926] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.479382] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 4.693681] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.895484] hub 1-1:1.0: USB hub found [ 4.899462] hub 1-1:1.0: 3 ports detected [ 4.913793] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.921576] panel-simple panel-lcd: Specify missing connector_type [ 4.931194] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.594143] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 7.613739] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.643737] Sending DHCP requests ., OK [ 7.687613] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 [ 7.695684] IP-Config: Complete: [ 7.698943] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 [ 7.709451] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) [ 7.717339] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 7.717352] nameserver0=192.168.201.1 [ 7.737521] Freeing unused kernel memory: 2048K [ 7.784629] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 8.622806] imx-ipuv3 2400000.ipu: IPUv3H probed [ 8.633127] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.650363] panel-simple panel-lcd: Specify missing connector_type [ 8.668421] imx-ipuv3 2800000.ipu: IPUv3H probed [ 8.677393] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.690669] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.698398] panel-simple panel-lcd: Specify missing connector_type [ 8.711903] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.712856] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.728023] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.736809] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.745257] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.763401] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.778028] panel-simple panel-lcd: Specify missing connector_type [ 8.787270] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.806909] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 8.817986] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 8.825401] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 8.831968] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 8.839314] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 8.846294] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 8.852412] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 8.854342] caam 2100000.crypto: Entropy delay = 3200 [ 8.859116] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 8.875950] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.884193] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.892430] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.900675] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.924572] caam 2100000.crypto: Instantiated RNG4 SH0 [ 8.952115] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 8.960007] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 8.968591] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 8.969434] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.976426] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 8.983961] panel-simple panel-lcd: Specify missing connector_type [ 8.985338] caam 2100000.crypto: Instantiated RNG4 SH1 [ 8.985352] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 8.985357] caam 2100000.crypto: job rings = 2, qi = 0 [ 9.085830] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.100138] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.100451] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 9.108415] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.121596] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.129904] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.132584] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 9.143449] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.153498] panel-simple panel-lcd: Specify missing connector_type [ 9.192019] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.214142] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.222371] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.230697] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.238946] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.254092] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.261798] panel-simple panel-lcd: Specify missing connector_type [ 9.536046] caam algorithms registered in /proc/crypto [ 9.542564] caam 2100000.crypto: registering rng-caam [ 9.549484] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.569408] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers [ 9.577688] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) ... [ 9.588714] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done. [ 9.597268] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/init-premount ... done. Begin: Mounting[ 9.611205] panel-simple panel-lcd: supply power not found, using dummy regulator root file system ... Begin: Runn[ 9.619184] panel-simple panel-lcd: Specify missing connector_type ing /scripts/nfs-top ... done. B[ 9.630383] panel-simple panel-lvds0: supply power not found, using dummy regulator egin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. [ 9.730188] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 10.589314] systemd[1]: System time before build time, advancing clock. [ 10.644014] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.668200] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 10.716708] systemd[1]: Set hostname to . [ 11.575974] systemd[1]: Queued start job for default target Graphical Interface. [ 11.585519] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 11.597984] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 11.607283] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 11.645083] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 11.684325] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 11.724703] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.764671] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 11.804034] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.844355] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.856782] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.894650] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.924186] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 11.963960] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 11.994162] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 12.024985] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 12.314106] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 12.324016] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 12.375319] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 12.415737] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 12.467900] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 12.504457] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 12.544972] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 12.554178] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 12.566300] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 12.606981] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 12.647382] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 12.690426] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 12.727474] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 12.767406] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 12.807241] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.820664] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.862235] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.897418] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 12.936935] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 12.979540] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 13.014308] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 13.054851] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 13.116680] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 13.433212] systemd-journald[274]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.180-cip34 #1 SMP Tue Jun 6 09:43:23 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10604077/extract-nfsrootfs-jss2mz5i' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10604077/extract-nfsrootfs-jss2mz5i' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10604077/environment . /lava-10604077/environment / # /lava-10604077/bin/lava-test-runner /lava-10604077/0 /lava-10604077/bin/lava-test-runner /lava-10604077/0 + export TESTRUN_ID=0_dmesg + cd /lava-10604077/0/tests/0_dmesg + cat uuid + UUID=10604077_1.6.2.4.1[ 27.286467] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 27.382079] [ 27.462440] [ 27.542480] + set[ 27.551936] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10604077/environment / # . /lava-10604077/environment/lava-10604077/bin/lava-test-runner /lava-10604077/1 / # /lava-10604077/bin/lava-test-runner /lava-10604077/1 + export TESTRUN_ID=1_bootrr + cd /lava-10604077/1/tests/1_bootrr + cat uuid + UUID=10604077_1.6.2.4.5[ 28.144850] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10604077/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 120000.hdmi backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-10604077/1/../bin/lava-test-case [ 29.303939] /lava-10604077/1/../bin/lava-test-case [ 29.400721] /lava-10604077/1/../bin/lava-test-case [ 29.442799] + set[ 29.474119] +x / #