[Enter `^Ec?' for help] U-Boot SPL 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45) U-Boot 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45 +0000) Model: Radxa Rock 2 Square DRAM: 2 GiB MMC: dwmmc@ff0c0000: 0, dwmmc@ff0f0000: 1 *** Warning - bad CRC, using default environment In: serial@ff690000 Out: serial@ff690000 Err: serial@ff690000 Incorrect eeprom header Net: Warning: ethernet@ff290000 (eth0) using random MAC address - 0a:27:7a:cb:a9:73 eth0: ethernet@ff290000 Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@ff290000 Waiting for PHY auto negotiation to complete...... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.201.150 (758 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x2000000 10604090/tftp-deploy-3ktrknvu/kernel/zImage tftp 0x2000000 10604090/tftp-deploy-3ktrknvu/kernel/zImage Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.150 Filename '10604090/tftp-deploy-3ktrknvu/kernel/zImage'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 3.6 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x4000000 10604090/tftp-deploy-3ktrknvu/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4000000 10604090/tftp-deploy-3ktrknvu/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.150 Filename '10604090/tftp-deploy-3ktrknvu/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 3.6 MiB/s done Bytes transferred = 16064277 (f51f15 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1f00000 10604090/tftp-deploy-3ktrknvu/dtb/rk3288-rock2-square.dtb tftp 0x1f00000 10604090/tftp-deploy-3ktrknvu/dtb/rk3288-rock2-square.dtb Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.150 Filename '10604090/tftp-deploy-3ktrknvu/dtb/rk3288-rock2-square.dtb'. Load address: 0x1f00000 Loading: *### 3.3 MiB/s done Bytes transferred = 41652 (a2b4 hex) => setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x2000000 0x4000000 0x1f00000 bootz 0x2000000 0x4000000 0x1f00000 Kernel image @ 0x2000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16064213 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Using Device Tree in place at 01f00000, end 01f0d2b3 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 5.10.180-cip34 (KernelCI@build-j1614509-arm-gcc-10-multi-v7-defconfig-lhmwp) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jun 6 09:43:23 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Radxa Rock 2 Square [ 0.000000] earlycon: uart0 at MMIO32 0xff690000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1973048K/2097152K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 58568K reserved, 65536K cma-reserved, 1245184K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009083] Switching to timer-based delay loop, resolution 41ns <6>[ 0.022913] Console: colour dummy device 80x30 <6>[ 0.028116] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.039787] pid_max: default: 32768 minimum: 301 <6>[ 0.045296] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.053630] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.063092] CPU: Testing write buffer coherency: ok <6>[ 0.068778] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.074854] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 <6>[ 0.082268] Setting up static identity map for 0x300000 - 0x3000ac <6>[ 0.091367] rcu: Hierarchical SRCU implementation. <6>[ 0.101757] EFI services will not be available. <6>[ 0.107304] smp: Bringing up secondary CPUs ... <6>[ 0.114338] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 <6>[ 0.114347] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.128576] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 <6>[ 0.128585] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.142806] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 <6>[ 0.142815] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.155289] smp: Brought up 1 node, 4 CPUs <6>[ 0.160074] SMP: Total of 4 processors activated (192.00 BogoMIPS). <6>[ 0.167262] CPU: All CPU(s) started in SVC mode. <6>[ 0.173242] devtmpfs: initialized <6>[ 0.186209] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 <6>[ 0.195170] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.206282] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.215959] pinctrl core: initialized pinctrl subsystem <6>[ 0.223997] DMI not present or invalid. <6>[ 0.229340] NET: Registered protocol family 16 <6>[ 0.236871] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.247329] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.247850] cpuidle: using governor menu <6>[ 0.259891] No ATAGs? <6>[ 0.262814] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.271912] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.282029] Serial: AMBA PL011 UART driver <6>[ 0.386936] iommu: Default domain type: Translated <6>[ 0.394151] vgaarb: loaded <5>[ 0.398395] SCSI subsystem initialized <6>[ 0.403254] usbcore: registered new interface driver usbfs <6>[ 0.409635] usbcore: registered new interface driver hub <6>[ 0.415793] usbcore: registered new device driver usb <6>[ 0.423611] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.429347] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.439690] PTP clock support registered <6>[ 0.447643] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.816327] NET: Registered protocol family 2 <6>[ 1.821682] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.831527] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.841054] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.849945] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.858277] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.865637] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.873255] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.881485] NET: Registered protocol family 1 <6>[ 1.887121] RPC: Registered named UNIX socket transport module. <6>[ 1.893950] RPC: Registered udp transport module. <6>[ 1.899433] RPC: Registered tcp transport module. <6>[ 1.904886] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.912268] PCI: CLS 0 bytes, default 64 <6>[ 1.917294] Trying to unpack rootfs image as initramfs... <6>[ 3.461170] Freeing initrd memory: 15688K <6>[ 3.466721] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available <5>[ 3.477583] Initialise system trusted keyrings <6>[ 3.482996] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 3.496951] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.504428] NFS: Registering the id_resolver key type <5>[ 3.510351] Key type id_resolver registered <5>[ 3.515228] Key type id_legacy registered <6>[ 3.520046] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.527710] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.536146] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.541709] Key type asymmetric registered <5>[ 3.546493] Asymmetric key parser 'x509' registered <6>[ 3.552214] bounce: pool size: 64 pages <6>[ 3.556741] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.565167] io scheduler mq-deadline registered <6>[ 3.570440] io scheduler kyber registered <6>[ 3.614921] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 3.623569] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 <6>[ 3.634789] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 3.643415] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 <6>[ 3.717426] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.727679] printk: console [ttyS2] disabled <6>[ 3.732724] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 43, base_baud = 1500000) is a 16550A <6>[ 3.742930] printk: console [ttyS2] enabled <6>[ 3.742930] printk: console [ttyS2] enabled <6>[ 3.752897] printk: bootconsole [uart0] disabled <6>[ 3.752897] printk: bootconsole [uart0] disabled <6>[ 3.766616] SuperH (H)SCI(F) driver initialized <6>[ 3.773471] msm_serial: driver initialized <6>[ 3.778632] STMicroelectronics ASC driver initialized <6>[ 3.786469] STM32 USART driver initialized <6>[ 3.811066] brd: module loaded <6>[ 3.822982] loop: module loaded <6>[ 3.842444] CAN device driver interface <6>[ 3.848404] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.856621] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.862486] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.869470] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.875798] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.885919] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 3.893264] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 3.903707] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.912347] usbcore: registered new interface driver pegasus <6>[ 3.919035] usbcore: registered new interface driver asix <6>[ 3.925401] usbcore: registered new interface driver ax88179_178a <6>[ 3.932559] usbcore: registered new interface driver cdc_ether <6>[ 3.939449] usbcore: registered new interface driver smsc75xx <6>[ 3.946213] usbcore: registered new interface driver smsc95xx <6>[ 3.952986] usbcore: registered new interface driver net1080 <6>[ 3.959660] usbcore: registered new interface driver cdc_subset <6>[ 3.966603] usbcore: registered new interface driver zaurus <6>[ 3.973227] usbcore: registered new interface driver cdc_ncm <4>[ 3.982874] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator <4>[ 3.991289] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator <6>[ 4.067948] dwc2 ff540000.usb: DWC OTG Controller <6>[ 4.073525] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1 <6>[ 4.081766] dwc2 ff540000.usb: irq 48, io mem 0xff540000 <6>[ 4.088784] hub 1-0:1.0: USB hub found <6>[ 4.093307] hub 1-0:1.0: 1 port detected <4>[ 4.098806] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator <4>[ 4.107226] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator <6>[ 4.247711] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM <6>[ 4.256276] dwc2 ff580000.usb: DWC OTG Controller <6>[ 4.261895] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2 <6>[ 4.270131] dwc2 ff580000.usb: irq 49, io mem 0xff580000 <6>[ 4.277094] hub 2-0:1.0: USB hub found <6>[ 4.281649] hub 2-0:1.0: 1 port detected <6>[ 4.287956] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.295552] ehci-pci: EHCI PCI platform driver <6>[ 4.300887] ehci-platform: EHCI generic platform driver <6>[ 4.307368] ehci-platform ff500000.usb: EHCI Host Controller <6>[ 4.314043] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3 <6>[ 4.323356] ehci-platform ff500000.usb: irq 47, io mem 0xff500000 <6>[ 4.357639] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 <6>[ 4.365567] hub 3-0:1.0: USB hub found <6>[ 4.370123] hub 3-0:1.0: 1 port detected <6>[ 4.375461] ehci-orion: EHCI orion driver <6>[ 4.380502] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.385468] ehci-st: EHCI STMicroelectronics driver <6>[ 4.391432] ehci-exynos: EHCI Exynos driver <6>[ 4.396588] ehci-atmel: EHCI Atmel driver <6>[ 4.401569] tegra-ehci: Tegra EHCI driver <6>[ 4.406565] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.413802] ohci-pci: OHCI PCI platform driver <6>[ 4.419130] ohci-platform: OHCI generic platform driver <6>[ 4.425523] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.430510] ohci-st: OHCI STMicroelectronics driver <6>[ 4.436444] ohci-atmel: OHCI Atmel driver <6>[ 4.442555] usbcore: registered new interface driver usb-storage <6>[ 4.457108] i2c /dev entries driver <6>[ 4.467583] VCC_DDR: supplied by vcc_sys <6>[ 4.474631] VCC_IO: supplied by vcc_sys <6>[ 4.481519] VDD_LOG: Bringing 1100000uV into 1000000-1000000uV <6>[ 4.490735] VDD_LOG: supplied by vcc_sys <6>[ 4.497701] VCC_20: supplied by vcc_sys <6>[ 4.504588] VCCIO_SD: supplied by VCC_IO <6>[ 4.512081] VDD10_LCD: supplied by VCC_IO <6>[ 4.520035] VCCA_CODEC: supplied by VCC_IO <6>[ 4.528053] VCCA_TP: supplied by vcc_sys <6>[ 4.535418] VCCIO_PMU: supplied by vcc_sys <6>[ 4.542611] VDD_10: supplied by VCC_20 <6>[ 4.549893] VCC_18: supplied by VCC_20 <6>[ 4.557177] VCC18_LCD: supplied by VCC_20 <6>[ 4.566278] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! <6>[ 4.575684] vdd_cpu: supplied by vcc_sys <6>[ 4.583029] vcc_flash: supplied by VCC_IO <6>[ 4.588404] vcc_sd: supplied by VCC_IO <6>[ 4.595205] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! <6>[ 4.604616] vdd_gpu: supplied by vcc_sys <4>[ 4.627653] dw_wdt ff800000.watchdog: No valid TOPs array specified <6>[ 4.644116] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 500000 KHz, changing to: 600000 KHz <6>[ 4.658560] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.665759] sdhci: Copyright(c) Pierre Ossman <6>[ 4.671739] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.679222] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.679285] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.679446] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.679500] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.679527] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller. <6>[ 4.679532] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a <6>[ 4.679553] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 40,32 bit host data width,256 deep fifo <6>[ 4.680209] dwmmc_rockchip ff0f0000.mmc: allocated mmc-pwrseq <6>[ 4.680213] mmc_host mmc0: card is non-removable. <6>[ 4.687409] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller. <6>[ 4.693295] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 4.695583] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 4.702185] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a <6>[ 4.710345] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 4.718040] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo <6>[ 4.724546] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 4.727595] usb 3-1: new high-speed USB device number 2 using ehci-platform <6>[ 4.735632] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.749685] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 4.755803] usbcore: registered new interface driver usbhid <6>[ 4.776478] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 4.780234] usbhid: USB HID core driver <6>[ 4.782122] NET: Registered protocol family 10 <6>[ 4.788008] mmc0: new high speed MMC card at address 0001 <6>[ 4.798063] Segment Routing with IPv6 <6>[ 4.809204] mmcblk0: mmc0:0001 032GE4 29.1 GiB <6>[ 4.816818] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.823977] mmcblk0boot0: mmc0:0001 032GE4 partition 1 4.00 MiB <6>[ 4.834630] NET: Registered protocol family 17 <6>[ 4.841087] mmcblk0boot1: mmc0:0001 032GE4 partition 2 4.00 MiB <6>[ 4.852101] can: controller area network core <6>[ 4.861976] mmcblk0rpmb: mmc0:0001 032GE4 partition 3 4.00 MiB, chardev (235:0) <6>[ 4.868263] NET: Registered protocol family 29 <6>[ 4.875677] mmcblk0: p1 p2 <6>[ 4.877968] can: raw protocol <6>[ 4.877974] can: broadcast manager protocol <6>[ 4.934749] can: netlink gateway - max_hops=1 <5>[ 4.940113] Key type dns_resolver registered <6>[ 4.945205] ThumbEE CPU extension supported. <6>[ 4.949436] hub 3-1:1.0: USB hub found <5>[ 4.950264] Registering SWP/SWPB emulation handler <6>[ 4.955010] hub 3-1:1.0: 4 ports detected <5>[ 4.960475] Loading compiled-in X.509 certificates <6>[ 4.992015] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 4.999295] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 5.006854] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). <6>[ 5.015044] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). <6>[ 5.021665] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). <6>[ 5.028285] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no). <3>[ 5.035491] rk_gmac-dwmac ff290000.ethernet: cannot get clock clk_mac_speed <6>[ 5.043562] rk_gmac-dwmac ff290000.ethernet: clock input from PHY <6>[ 5.055668] rk_gmac-dwmac ff290000.ethernet: init for RGMII <6>[ 5.062279] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35 <6>[ 5.070550] rk_gmac-dwmac ff290000.ethernet: DWMAC1000 <6>[ 5.076676] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported <6>[ 5.085320] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported <6>[ 5.093978] rk_gmac-dwmac ff290000.ethernet: COE Type 2 <6>[ 5.100106] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported <6>[ 5.108276] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported <6>[ 5.115786] rk_gmac-dwmac ff290000.ethernet: Normal descriptors <6>[ 5.122693] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled <6>[ 5.129501] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 5.138745] rk_gmac-dwmac ff290000.ethernet: device MAC address 7a:3e:91:7b:cf:31 <6>[ 5.277655] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) <6>[ 5.291969] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL) <3>[ 5.311466] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <6>[ 5.311518] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <3>[ 5.320536] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <3>[ 5.337757] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <6>[ 5.347055] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 5.347356] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 5.354755] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 5.369064] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 5.383149] rk_gmac-dwmac ff290000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL) <6>[ 5.396181] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 5.404387] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 5.405717] rk_gmac-dwmac ff290000.ethernet eth0: No Safety Features support found <6>[ 5.412084] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <4>[ 5.420826] rk_gmac-dwmac ff290000.ethernet eth0: PTP not supported by HW <6>[ 5.427348] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 5.446312] rk_gmac-dwmac ff290000.ethernet eth0: configuring for phy/rgmii link mode <6>[ 9.579017] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 9.588961] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 9.617920] Sending DHCP requests .., OK <6>[ 12.722668] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.112 <6>[ 12.732139] IP-Config: Complete: <6>[ 12.736101] device=eth0, hwaddr=7a:3e:91:7b:cf:31, ipaddr=192.168.201.112, mask=255.255.255.0, gw=192.168.201.1 <6>[ 12.748323] host=192.168.201.112, domain=lava-rack, nis-domain=(none) <6>[ 12.756349] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 12.756376] nameserver0=192.168.201.1 <4>[ 12.773214] dw-apb-uart ff690000.serial: forbid DMA for kernel console <6>[ 12.794053] Freeing unused kernel memory: 2048K <6>[ 12.817731] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.893922] udevd[118]: starting version 3.2.9 <5>[ 12.899820] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.907460] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.915048] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 12.926684] udevd[118]: specified user 'tss' unknown <27>[ 12.932698] udevd[118]: specified group 'tss' unknown <30>[ 12.939512] udevd[119]: starting eudev-3.2.9 <6>[ 13.081452] rockchip-vop ff930000.vop: Adding to iommu group 0 <6>[ 13.088597] rockchip-vop ff940000.vop: Adding to iommu group 1 <6>[ 13.099868] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 13.108182] rockchip-drm display-subsystem: bound ff930000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 13.119365] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 13.127074] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 13.133627] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 13.148802] rockchip-drm display-subsystem: bound ff940000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 13.159432] dwhdmi-rockchip ff980000.hdmi: Detected HDMI TX controller v2.00a with HDCP (DWC MHL PHY) <6>[ 13.164899] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 13.190101] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 13.197804] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <4>[ 13.200499] rtc-hym8563 0-0051: no valid clock/calendar values available <6>[ 13.204331] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 13.224947] rtc-hym8563 0-0051: registered as rtc0 <6>[ 13.238199] rockchip-drm display-subsystem: bound ff980000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm]) <6>[ 13.243925] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <4>[ 13.250261] rtc-hym8563 0-0051: no valid clock/calendar values available <3>[ 13.265117] rtc-hym8563 0-0051: hctosys: unable to read the hardware clock <6>[ 13.273397] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 13.273404] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 13.281107] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 13.281125] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 13.298078] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0 <6>[ 13.317357] dwmmc_rockchip ff0d0000.mmc: allocated mmc-pwrseq <6>[ 13.324096] mmc_host mmc2: card is non-removable. <6>[ 13.353169] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 13.376244] panfrost ffa30000.gpu: clock rate = 400000000 <6>[ 13.387638] rk3288-crypto ff8a0000.crypto: will run requests pump with realtime priority <4>[ 13.391032] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) <6>[ 13.397108] panfrost ffa30000.gpu: mali-t760 id 0x750 major 0x0 minor 0x0 status 0x1 <4>[ 13.405065] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <6>[ 13.412368] panfrost ffa30000.gpu: features: 00000000,100277bf, issues: 00000000,24040400 <4>[ 13.420345] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <6>[ 13.428217] panfrost ffa30000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 <6>[ 13.428220] panfrost ffa30000.gpu: shader_present=0xf l2_present=0x1 <6>[ 13.456631] rk3288-crypto ff8a0000.crypto: Crypto Accelerator successfully registered <4>[ 13.458262] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) <6>[ 13.472357] [drm] Initialized panfrost 1.1.0 20180908 for ffa30000.gpu on minor 1 <6>[ 13.525769] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) done <6>[ 13.540298] mmc2: new high speed SDIO card at address 0001 Saving random seed: OK Starting network: <5>[ 13.569186] cfg80211: Loading compiled-in X.509 certificates for regulatory database ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # <5>[ 13.606626] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 13.614312] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 13.624260] cfg80211: failed to load regulatory.db <6>[ 13.635126] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 13.645250] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed wit h error -2 / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10604090/environment . /lava-10604090/environment / # /lava-10604090/bin/lava-test-runner /lava-10604090/0 /lava-10604090/bin/lava-test-runner /lava-10604090/0 + export 'TESTRUN_ID=0_dmesg' + <8>[ 14.200224] cd /lava-10604090/0/tests/0_dmesg + cat uuid + UUID=10604090_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.226819] <8>[ 14.247791] <8>[ 14.269347] + set +x <8>[ 14.279671] / # <6>[ 14.297684] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10604090/environment / # . /lava-10604090/environment/lava-10604090/bin/lava-test-runner /lava-10604090/1 / # <3>[ 14.665178] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 /lava-10604090/bin/lava-test-runner /lava-10604090/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10604090/1/tests/1_bootrr + cat uuid <8>[ 14.776275] + UUID=10604090_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10604090/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-10604090/1/../bin/lav<8>[ 14.806875] a-test-case /lava-10604090/1/../bin/lava-test-case <8>[ 14.831728] /lava-10604090/1/../bin/lava-test-case <8>[ 14.847701] /lava-10604090/1/../bin/lava-test-case <8>[ 14.872650] /lava-10604090/1/../bin/lava-test-case <8>[ 14.897833] /lava-10604090/1/../bin/lava-test-case <8>[ 14.920760] /lava-10604090/1/../bin/lava-test-case <8>[ 14.943643] /lava-10604090/1/../bin/lava-test-case <8>[ 14.963179] /lava-10604090/1/../bin/lava-test-case <8>[ 14.984302] + set +x <8>[ 14.993090] / #