[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10853494/tftp-deploy-4pk7haod/kernel/zImage tftp 0x10000000 10853494/tftp-deploy-4pk7haod/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '10853494/tftp-deploy-4pk7haod/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 9.9 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 10853494/tftp-deploy-4pk7haod/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10853494/tftp-deploy-4pk7haod/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '10853494/tftp-deploy-4pk7haod/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 11.3 MiB/s done Bytes transferred = 16084171 (f56ccb hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10853494/tftp-deploy-4pk7haod/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10853494/tftp-deploy-4pk7haod/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '10853494/tftp-deploy-4pk7haod/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16084107 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.184-cip36 (KernelCI@build-j74625-arm-gcc-10-multi-v7-defconfig-cstdq) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jun 22 00:58:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932652K/1048576K available (14336K kernel code, 2239K rwdata, 5356K rodata, 2048K init, 424K bss, 50388K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022283] Console: colour dummy device 80x30 <6>[ 0.024171] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034586] pid_max: default: 32768 minimum: 301 <6>[ 0.039620] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047038] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055660] CPU: Testing write buffer coherency: ok <6>[ 0.060152] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065716] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072079] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079812] rcu: Hierarchical SRCU implementation. <6>[ 0.086808] EFI services will not be available. <6>[ 0.089043] smp: Bringing up secondary CPUs ... <6>[ 0.094338] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094348] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105690] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105698] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116883] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116892] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127328] smp: Brought up 1 node, 4 CPUs <6>[ 0.131551] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138008] CPU: All CPU(s) started in SVC mode. <6>[ 0.143435] devtmpfs: initialized <6>[ 0.153935] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159280] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169151] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179360] pinctrl core: initialized pinctrl subsystem <6>[ 0.183840] DMI not present or invalid. <6>[ 0.186953] NET: Registered protocol family 16 <6>[ 0.194231] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200881] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201074] cpuidle: using governor menu <6>[ 0.209150] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.386937] vdd1p1: supplied by regulator-dummy <6>[ 0.396015] vdd3p0: supplied by regulator-dummy <6>[ 0.404999] vdd2p5: supplied by regulator-dummy <6>[ 0.414003] vddarm: supplied by regulator-dummy <6>[ 0.423148] vddpu: supplied by regulator-dummy <6>[ 0.431941] vddsoc: supplied by regulator-dummy <6>[ 0.759293] No ATAGs? <6>[ 0.759479] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.767257] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.777435] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.787714] Serial: AMBA PL011 UART driver <6>[ 0.791877] printk: console [ramoops-1] enabled <6>[ 0.794213] pstore: Registered ramoops as persistent store backend <6>[ 0.800478] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.838291] iommu: Default domain type: Translated <6>[ 0.840897] vgaarb: loaded <5>[ 0.844499] SCSI subsystem initialized <6>[ 0.847974] usbcore: registered new interface driver usbfs <6>[ 0.853328] usbcore: registered new interface driver hub <6>[ 0.858918] usbcore: registered new device driver usb <6>[ 0.865727] i2c i2c-0: IMX I2C adapter registered <6>[ 0.870443] i2c i2c-1: IMX I2C adapter registered <6>[ 0.874945] i2c i2c-2: IMX I2C adapter registered <6>[ 0.880395] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.884258] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.893703] PTP clock support registered <6>[ 0.901342] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.962761] NET: Registered protocol family 2 <6>[ 1.964967] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.973351] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.980835] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.988908] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.996368] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.003057] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.009723] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.017212] NET: Registered protocol family 1 <6>[ 2.022231] RPC: Registered named UNIX socket transport module. <6>[ 2.027782] RPC: Registered udp transport module. <6>[ 2.032774] RPC: Registered tcp transport module. <6>[ 2.037698] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.044427] PCI: CLS 0 bytes, default 64 <6>[ 2.049082] Trying to unpack rootfs image as initramfs... <6>[ 3.399924] Freeing initrd memory: 15708K <4>[ 3.402067] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.409110] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.418959] Initialise system trusted keyrings <6>[ 3.422152] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.434467] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.438441] NFS: Registering the id_resolver key type <5>[ 3.443103] Key type id_resolver registered <5>[ 3.447456] Key type id_legacy registered <6>[ 3.451841] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.458682] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.466395] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.471458] Key type asymmetric registered <5>[ 3.475299] Asymmetric key parser 'x509' registered <6>[ 3.480471] bounce: pool size: 64 pages <6>[ 3.484570] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.492193] io scheduler mq-deadline registered <6>[ 3.496961] io scheduler kyber registered <6>[ 3.540870] mxs-dma 110000.dma-apbh: initialized <4>[ 3.547688] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.554624] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.611030] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.619230] SuperH (H)SCI(F) driver initialized <6>[ 3.622235] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.631038] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.638980] printk: console [ttymxc1] enabled <6>[ 3.638980] printk: console [ttymxc1] enabled <6>[ 3.648147] printk: bootconsole [ec_imx21] disabled <6>[ 3.648147] printk: bootconsole [ec_imx21] disabled <6>[ 3.659815] msm_serial: driver initialized <6>[ 3.665906] STMicroelectronics ASC driver initialized <6>[ 3.673220] STM32 USART driver initialized <4>[ 3.687989] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.695906] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.702684] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.719349] brd: module loaded <6>[ 3.732708] loop: module loaded <6>[ 3.740037] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.748294] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.756584] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.765047] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.773054] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.780778] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.788346] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.798954] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.806247] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.815335] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.826144] scsi host0: ahci-imx <6>[ 3.830024] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.850664] CAN device driver interface <6>[ 3.856135] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.865649] pps pps0: new PPS source ptp0 <6>[ 3.902551] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.910141] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.915399] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.921662] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.927329] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.939246] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.946975] usbcore: registered new interface driver pegasus <6>[ 3.952959] usbcore: registered new interface driver asix <6>[ 3.958666] usbcore: registered new interface driver ax88179_178a <6>[ 3.965081] usbcore: registered new interface driver cdc_ether <6>[ 3.971224] usbcore: registered new interface driver smsc75xx <6>[ 3.977312] usbcore: registered new interface driver smsc95xx <6>[ 3.983376] usbcore: registered new interface driver net1080 <6>[ 3.989334] usbcore: registered new interface driver cdc_subset <6>[ 3.995567] usbcore: registered new interface driver zaurus <6>[ 4.001497] usbcore: registered new interface driver cdc_ncm <6>[ 4.010959] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.017778] ehci-pci: EHCI PCI platform driver <6>[ 4.022543] ehci-platform: EHCI generic platform driver <6>[ 4.028335] ehci-orion: EHCI orion driver <6>[ 4.032875] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.037340] ehci-st: EHCI STMicroelectronics driver <6>[ 4.042691] ehci-exynos: EHCI Exynos driver <6>[ 4.047322] ehci-atmel: EHCI Atmel driver <6>[ 4.051795] tegra-ehci: Tegra EHCI driver <6>[ 4.056282] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.062764] ohci-pci: OHCI PCI platform driver <6>[ 4.067518] ohci-platform: OHCI generic platform driver <6>[ 4.073294] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.077761] ohci-st: OHCI STMicroelectronics driver <6>[ 4.083122] ohci-atmel: OHCI Atmel driver <6>[ 4.088670] usbcore: registered new interface driver usb-storage <6>[ 4.103116] i2c /dev entries driver <6>[ 4.126537] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.133016] sdhci: Copyright(c) Pierre Ossman <6>[ 4.140375] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.148637] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.155879] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.160045] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.161162] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.171859] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.179198] usbcore: registered new interface driver usbhid <6>[ 4.185069] usbhid: USB HID core driver <6>[ 4.185114] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.194918] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.195779] NET: Registered protocol family 10 <6>[ 4.201481] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.214677] Segment Routing with IPv6 <6>[ 4.218686] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.220283] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.225461] NET: Registered protocol family 17 <6>[ 4.232945] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.236791] can: controller area network core <6>[ 4.236871] NET: Registered protocol family 29 <6>[ 4.253312] can: raw protocol <6>[ 4.256561] can: broadcast manager protocol <6>[ 4.261020] can: netlink gateway - max_hops=1 <5>[ 4.266104] Key type dns_resolver registered <6>[ 4.272701] ThumbEE CPU extension supported. <5>[ 4.277284] Registering SWP/SWPB emulation handler <5>[ 4.282652] Loading compiled-in X.509 certificates <6>[ 4.285364] mmc2: new high speed SDHC card at address e624 <6>[ 4.292602] pstore: Using crash dump compression: deflate <6>[ 4.294775] mmcblk2: mmc2:e624 SL16G 14.8 GiB <4>[ 4.312108] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.319789] GPT:29296874 != 31116287 <4>[ 4.319976] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.323679] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.323684] GPT:29296874 != 31116287 <4>[ 4.323687] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.323734] mmcblk2: p1 p2 p3 <4>[ 4.331614] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.358405] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.374845] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.384887] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.390059] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.421482] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.428625] hub 1-0:1.0: USB hub found <6>[ 4.432787] hub 1-0:1.0: 1 port detected <6>[ 4.441401] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.456647] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.464570] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.472495] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.484616] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.492528] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.500320] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.510328] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.522569] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.530465] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.538376] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.552482] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.761402] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.963065] hub 1-1:1.0: USB hub found <6>[ 4.967299] hub 1-1:1.0: 3 ports detected <4>[ 4.981793] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.989835] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.999702] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.681883] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.689741] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.711405] Sending DHCP requests ., OK <6>[ 7.755584] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 7.763913] IP-Config: Complete: <6>[ 7.767434] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.778187] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 7.786340] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.786354] nameserver0=192.168.201.1 <6>[ 7.804759] Freeing unused kernel memory: 2048K <6>[ 7.852427] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.982573] udevd[142]: starting version 3.2.9 <5>[ 7.988155] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.995216] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.002064] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.015809] udevd[142]: specified user 'tss' unknown <27>[ 8.021238] udevd[142]: specified group 'tss' unknown <30>[ 8.028802] udevd[143]: starting eudev-3.2.9 <6>[ 8.360941] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.368169] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.386033] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.404576] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.413338] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.451549] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.459478] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.494306] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.502953] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.511633] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.520207] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.543205] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.609322] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.670085] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.675530] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.682437] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.693757] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.745248] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.784291] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.802031] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.808866] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.861577] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.881430] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.887842] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <4>[ 8.916835] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.922936] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 8.924991] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.940675] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.948828] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.958609] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.967260] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.975860] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.984467] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.996725] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.004819] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.014641] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.033777] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.041026] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 9.042462] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.053056] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 9.056146] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.072459] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.083505] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.091922] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.100538] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.118984] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.127592] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.136193] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.144780] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.156189] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.164262] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.323758] caam algorithms registered in /proc/crypto <6>[ 9.331171] caam 2100000.crypto: registering rng-caam <4>[ 9.338936] panel-simple panel-lvds0: supply power not found, using dummy regulator done Saving random seed: <6>[ 9.367473] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <5>[ 9.376518] random: dd: uninitialized urandom read (32 bytes read) <6>[ 9.377694] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) OK <6>[ 9.392571] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 9.401507] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.413581] panel-simple panel-lcd: supply power not found, using dummy regulator ip: RTNETLINK answers: File exist<4>[ 9.421617] panel-simple panel-lcd: Specify missing connector_type s FAIL <4>[ 9.433151] panel-simple panel-lvds0: supply power not found, using dummy regulator Starting dropbear sshd: <5>[ 9.472191] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # <5>[ 9.518975] random: crng init done <5>[ 9.522728] random: 1 urandom warning(s) missed due to ratelimiting / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10853494/environment . /lava-10853494/environment / # /lava-10853494/bin/lava-test-runner /lava-10853494/0 /lava-10853494/bin/lava-test-runner /lava-10853494/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10853494/0/tests/0_dmesg + <8>[ 10.072308] cat uuid + UUID=10853494_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.115844] <8>[ 10.156701] <8>[ 10.197344] + set<8>[ 10.207298] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10853494/environment / # . /lava-10853494/environment/lava-10853494/bin/lava-test-runner /lava-10853494/1 / # /lava-10853494/bin/lava-test-runner /lava-10853494/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10853494/1/tests/1_bootrr <8>[ 10.715138] + cat uuid + UUID=10853494_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10853494/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds 120000.hdmi panel-lcd panel-lvds0 /lava-10853494/1/../bin/lava-test-case <8>[ 11.791799] /lava-10853494/1/../bin/lava-test-case <8>[ 11.831234] /lava-10853494/1/../bin/lava-test-case <8>[ 11.856382] + set<8>[ 11.875492] +x / #