[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11517180/tftp-deploy-bitbqx9n/kernel/zImage tftp 0x10000000 11517180/tftp-deploy-bitbqx9n/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11517180/tftp-deploy-bitbqx9n/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 14.1 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 11517180/tftp-deploy-bitbqx9n/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11517180/tftp-deploy-bitbqx9n/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11517180/tftp-deploy-bitbqx9n/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.8 MiB/s done Bytes transferred = 16072921 (f540d9 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11517180/tftp-deploy-bitbqx9n/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11517180/tftp-deploy-bitbqx9n/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11517180/tftp-deploy-bitbqx9n/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.8 MiB/s done Bytes transferred = 42645 (a695 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16072857 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d694 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.191-cip38 (KernelCI@build-j44326-arm-gcc-10-multi-v7-defconfig-4fqbf) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Sep 13 15:08:02 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932656K/1048576K available (14336K kernel code, 2239K rwdata, 5360K rodata, 2048K init, 424K bss, 50384K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022513] Console: colour dummy device 80x30 <6>[ 0.024404] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034812] CPU: Testing write buffer coherency: ok <6>[ 0.039946] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.045243] pid_max: default: 32768 minimum: 301 <6>[ 0.050271] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057707] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066575] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072319] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080107] rcu: Hierarchical SRCU implementation. <6>[ 0.087290] EFI services will not be available. <6>[ 0.089526] smp: Bringing up secondary CPUs ... <6>[ 0.094819] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094828] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106217] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.106225] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117365] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117373] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127809] smp: Brought up 1 node, 4 CPUs <6>[ 0.132032] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138490] CPU: All CPU(s) started in SVC mode. <6>[ 0.143917] devtmpfs: initialized <6>[ 0.154282] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159626] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169495] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179710] pinctrl core: initialized pinctrl subsystem <6>[ 0.184202] DMI not present or invalid. <6>[ 0.187292] NET: Registered protocol family 16 <6>[ 0.194596] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201287] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201479] cpuidle: using governor menu <6>[ 0.209514] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.387688] vdd1p1: supplied by regulator-dummy <6>[ 0.396770] vdd3p0: supplied by regulator-dummy <6>[ 0.405790] vdd2p5: supplied by regulator-dummy <6>[ 0.414780] vddarm: supplied by regulator-dummy <6>[ 0.423958] vddpu: supplied by regulator-dummy <6>[ 0.432739] vddsoc: supplied by regulator-dummy <6>[ 0.760210] No ATAGs? <6>[ 0.760398] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.768171] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.778560] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.789208] Serial: AMBA PL011 UART driver <6>[ 0.793450] printk: console [ramoops-1] enabled <6>[ 0.795747] pstore: Registered ramoops as persistent store backend <6>[ 0.801937] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.839677] iommu: Default domain type: Translated <6>[ 0.842392] vgaarb: loaded <5>[ 0.845844] SCSI subsystem initialized <6>[ 0.849521] usbcore: registered new interface driver usbfs <6>[ 0.854711] usbcore: registered new interface driver hub <6>[ 0.860302] usbcore: registered new device driver usb <6>[ 0.867130] i2c i2c-0: IMX I2C adapter registered <6>[ 0.871818] i2c i2c-1: IMX I2C adapter registered <6>[ 0.876325] i2c i2c-2: IMX I2C adapter registered <6>[ 0.881795] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.885664] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.895058] PTP clock support registered <6>[ 0.902815] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.974025] NET: Registered protocol family 2 <6>[ 1.976217] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.984654] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.992096] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.000177] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.007628] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.014315] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.020984] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.028469] NET: Registered protocol family 1 <6>[ 2.033511] RPC: Registered named UNIX socket transport module. <6>[ 2.039044] RPC: Registered udp transport module. <6>[ 2.044036] RPC: Registered tcp transport module. <6>[ 2.048961] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.055689] PCI: CLS 0 bytes, default 64 <6>[ 2.060349] Trying to unpack rootfs image as initramfs... <6>[ 3.417168] Freeing initrd memory: 15700K <4>[ 3.419024] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.426575] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.436209] Initialise system trusted keyrings <6>[ 3.439330] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.451503] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.455506] NFS: Registering the id_resolver key type <5>[ 3.460088] Key type id_resolver registered <5>[ 3.464520] Key type id_legacy registered <6>[ 3.468855] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.475738] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.483420] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.488478] Key type asymmetric registered <5>[ 3.492336] Asymmetric key parser 'x509' registered <6>[ 3.497540] bounce: pool size: 64 pages <6>[ 3.501586] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.509231] io scheduler mq-deadline registered <6>[ 3.514012] io scheduler kyber registered <6>[ 3.559007] mxs-dma 110000.dma-apbh: initialized <4>[ 3.565953] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.572894] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.630294] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.638498] SuperH (H)SCI(F) driver initialized <6>[ 3.641434] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.650324] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.658240] printk: console [ttymxc1] enabled <6>[ 3.658240] printk: console [ttymxc1] enabled <6>[ 3.667415] printk: bootconsole [ec_imx21] disabled <6>[ 3.667415] printk: bootconsole [ec_imx21] disabled <6>[ 3.679238] msm_serial: driver initialized <6>[ 3.685164] STMicroelectronics ASC driver initialized <6>[ 3.692485] STM32 USART driver initialized <4>[ 3.707469] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.715394] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.722204] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.738935] brd: module loaded <6>[ 3.749810] loop: module loaded <6>[ 3.757256] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.765487] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.773793] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.782241] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.790264] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.798010] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.805584] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.816193] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.823469] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.832531] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.843358] scsi host0: ahci-imx <6>[ 3.847215] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.868120] CAN device driver interface <6>[ 3.873632] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.883126] pps pps0: new PPS source ptp0 <6>[ 3.920102] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.927745] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.933011] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.939265] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.944948] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.957072] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.964810] usbcore: registered new interface driver pegasus <6>[ 3.970775] usbcore: registered new interface driver asix <6>[ 3.976493] usbcore: registered new interface driver ax88179_178a <6>[ 3.982901] usbcore: registered new interface driver cdc_ether <6>[ 3.989043] usbcore: registered new interface driver smsc75xx <6>[ 3.995124] usbcore: registered new interface driver smsc95xx <6>[ 4.001175] usbcore: registered new interface driver net1080 <6>[ 4.007154] usbcore: registered new interface driver cdc_subset <6>[ 4.013390] usbcore: registered new interface driver zaurus <6>[ 4.019297] usbcore: registered new interface driver cdc_ncm <6>[ 4.028894] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.035714] ehci-pci: EHCI PCI platform driver <6>[ 4.040463] ehci-platform: EHCI generic platform driver <6>[ 4.046285] ehci-orion: EHCI orion driver <6>[ 4.050796] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.055303] ehci-st: EHCI STMicroelectronics driver <6>[ 4.060637] ehci-exynos: EHCI Exynos driver <6>[ 4.065298] ehci-atmel: EHCI Atmel driver <6>[ 4.069759] tegra-ehci: Tegra EHCI driver <6>[ 4.074277] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.080741] ohci-pci: OHCI PCI platform driver <6>[ 4.085521] ohci-platform: OHCI generic platform driver <6>[ 4.091280] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.095803] ohci-st: OHCI STMicroelectronics driver <6>[ 4.101161] ohci-atmel: OHCI Atmel driver <6>[ 4.106725] usbcore: registered new interface driver usb-storage <6>[ 4.121360] i2c /dev entries driver <6>[ 4.145437] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.151891] sdhci: Copyright(c) Pierre Ossman <6>[ 4.159375] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.167699] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.174945] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.175139] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.180231] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.190902] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.198277] usbcore: registered new interface driver usbhid <6>[ 4.204157] usbhid: USB HID core driver <6>[ 4.204211] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.214003] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.214959] NET: Registered protocol family 10 <6>[ 4.220544] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.222343] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.226354] Segment Routing with IPv6 <6>[ 4.243883] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.245496] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.250657] NET: Registered protocol family 17 <6>[ 4.257563] mmc2: new high speed SDHC card at address 0001 <6>[ 4.261961] can: controller area network core <6>[ 4.268617] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 4.272433] NET: Registered protocol family 29 <6>[ 4.281535] can: raw protocol <6>[ 4.284799] can: broadcast manager protocol <6>[ 4.289261] can: netlink gateway - max_hops=1 <4>[ 4.289783] GPT:Primary header thinks Alt. header is not at the end of the disk. <5>[ 4.294391] Key type dns_resolver registered <4>[ 4.301573] GPT:29296874 != 30560255 <4>[ 4.309958] GPT:Alternate GPT header not at the end of the disk. <6>[ 4.311923] ThumbEE CPU extension supported. <4>[ 4.316257] GPT:29296874 != 30560255 <4>[ 4.316261] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.316317] mmcblk2: p1 p2 p3 <5>[ 4.320812] Registering SWP/SWPB emulation handler <5>[ 4.338733] Loading compiled-in X.509 certificates <6>[ 4.348830] pstore: Using crash dump compression: deflate <4>[ 4.376723] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.384635] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.392588] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.409112] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.419026] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.424221] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.452917] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.460094] hub 1-0:1.0: USB hub found <6>[ 4.464240] hub 1-0:1.0: 1 port detected <6>[ 4.472952] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.488259] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.496176] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.504102] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.516292] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.524201] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.532031] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.542013] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.554316] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.562188] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.570150] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.583985] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.792853] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.994559] hub 1-1:1.0: USB hub found <6>[ 4.998775] hub 1-1:1.0: 3 ports detected <4>[ 5.009476] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.017452] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.025752] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.683305] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.692889] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.722837] Sending DHCP requests ., OK <6>[ 7.767036] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 7.775381] IP-Config: Complete: <6>[ 7.778903] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.789667] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 7.797820] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.797832] nameserver0=192.168.201.1 <6>[ 7.816851] Freeing unused kernel memory: 2048K <6>[ 7.854015] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.990155] udevd[136]: starting version 3.2.9 <5>[ 7.995894] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.002932] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.009802] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.025304] udevd[136]: specified user 'tss' unknown <27>[ 8.030744] udevd[136]: specified group 'tss' unknown <30>[ 8.038307] udevd[137]: starting eudev-3.2.9 <6>[ 8.355752] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.362526] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.373531] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.381478] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.407012] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.448117] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.456135] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.534148] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.542861] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.551507] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.551862] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.560119] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.568143] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.585088] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.594511] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.616066] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.624069] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.626869] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.653672] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.672063] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.679978] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.686846] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.702487] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.708881] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.715297] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.735683] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.803024] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.811566] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.820197] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.828749] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.843041] caam 2100000.crypto: Entropy delay = 3200 <4>[ 8.862226] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.877534] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.886560] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.909159] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.937965] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.946503] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.955090] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.963637] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.969917] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.977521] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.984429] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 9.021362] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.035261] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.043258] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.095184] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.103817] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.112374] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.118573] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 9.120983] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.130647] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 9.137102] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.161263] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.169264] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.179961] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.188554] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.197245] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.205872] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.216325] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.233013] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.241027] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.252490] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.261209] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.270031] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.278694] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.459598] caam algorithms registered in /proc/crypto <6>[ 9.466423] caam 2100000.crypto: registering rng-caam <4>[ 9.473657] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.495851] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.503800] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.515561] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.524106] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.532628] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.541157] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.551166] panel-simple panel-lvds0: supply power not found, using dummy regulator done Saving random seed: <4>[ 9.575725] panel-simple panel-lcd: supply power not found, using dummy regulator <5>[ 9.582621] random: dd: uninitialized urandom read (32 bytes read) <4>[ 9.583700] panel-simple panel-lcd: Specify missing connector_type OK <6>[ 9.600738] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 9.609370] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.619416] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) ip: RTNETLINK answers: File exist<6>[ 9.627997] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) s FAIL <5>[ 9.654242] random: crng init done <5>[ 9.657932] random: 1 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11517180/environment . /lava-11517180/environment / # /lava-11517180/bin/lava-test-runner /lava-11517180/0 /lava-11517180/bin/lava-test-runner /lava-11517180/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11517180/0/tests/0_dmesg + cat uuid + UUID=11517180_1.5.2<8>[ 10.295854] .4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.342371] <8>[ 10.383799] <8>[ 10.425297] + set<8>[ 10.435218] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11517180/environment / # . /lava-11517180/environment/lava-11517180/bin/lava-test-runner /lava-11517180/1 / # /lava-11517180/bin/lava-test-runner /lava-11517180/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11517180/1/tests/1_bootrr + cat uuid + UUID=11517180_1.5<8>[ 10.943110] .2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11517180/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd 120000.hdmi /lava-11517180/1/../bin/lava-test-case <8>[ 12.023363] /lava-11517180/1/../bin/lava-test-case <8>[ 12.063125] /lava-11517180/1/../bin/lava-test-case <8>[ 12.088227] + set<8>[ 12.107000] +x / #