[Enter `^Ec?' for help] U-Boot SPL 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45) U-Boot 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45 +0000) Model: Radxa Rock 2 Square DRAM: 2 GiB MMC: dwmmc@ff0c0000: 0, dwmmc@ff0f0000: 1 In: serial@ff690000 Out: serial@ff690000 Err: serial@ff690000 Incorrect eeprom header Net: eth0: ethernet@ff290000 Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@ff290000 Waiting for PHY auto negotiation to complete...... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.201.22 (761 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x2000000 11517175/tftp-deploy-d0dk0sjy/kernel/zImage tftp 0x2000000 11517175/tftp-deploy-d0dk0sjy/kernel/zImage Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '11517175/tftp-deploy-d0dk0sjy/kernel/zImage'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 3.6 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x4000000 11517175/tftp-deploy-d0dk0sjy/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4000000 11517175/tftp-deploy-d0dk0sjy/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '11517175/tftp-deploy-d0dk0sjy/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 3.6 MiB/s done Bytes transferred = 16071189 (f53a15 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1f00000 11517175/tftp-deploy-d0dk0sjy/dtb/rk3288-rock2-square.dtb tftp 0x1f00000 11517175/tftp-deploy-d0dk0sjy/dtb/rk3288-rock2-square.dtb Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '11517175/tftp-deploy-d0dk0sjy/dtb/rk3288-rock2-square.dtb'. Load address: 0x1f00000 Loading: *### 3.6 MiB/s done Bytes transferred = 41652 (a2b4 hex) => setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x2000000 0x4000000 0x1f00000 bootz 0x2000000 0x4000000 0x1f00000 Kernel image @ 0x2000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16071125 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Using Device Tree in place at 01f00000, end 01f0d2b3 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 5.10.191-cip38 (KernelCI@build-j44326-arm-gcc-10-multi-v7-defconfig-4fqbf) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Sep 13 15:08:02 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Radxa Rock 2 Square [ 0.000000] earlycon: uart0 at MMIO32 0xff690000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1973036K/2097152K available (14336K kernel code, 2239K rwdata, 5360K rodata, 2048K init, 424K bss, 58580K reserved, 65536K cma-reserved, 1245184K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009083] Switching to timer-based delay loop, resolution 41ns <6>[ 0.022930] Console: colour dummy device 80x30 <6>[ 0.028130] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.039799] CPU: Testing write buffer coherency: ok <6>[ 0.045473] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.051314] pid_max: default: 32768 minimum: 301 <6>[ 0.056807] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.065139] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.074830] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 <6>[ 0.082248] Setting up static identity map for 0x300000 - 0x3000ac <6>[ 0.091346] rcu: Hierarchical SRCU implementation. <6>[ 0.101744] EFI services will not be available. <6>[ 0.107287] smp: Bringing up secondary CPUs ... <6>[ 0.114311] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 <6>[ 0.114320] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.128537] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 <6>[ 0.128546] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.142750] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 <6>[ 0.142760] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.155233] smp: Brought up 1 node, 4 CPUs <6>[ 0.160019] SMP: Total of 4 processors activated (192.00 BogoMIPS). <6>[ 0.167206] CPU: All CPU(s) started in SVC mode. <6>[ 0.173181] devtmpfs: initialized <6>[ 0.186075] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 <6>[ 0.195017] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.206128] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.215798] pinctrl core: initialized pinctrl subsystem <6>[ 0.223845] DMI not present or invalid. <6>[ 0.229187] NET: Registered protocol family 16 <6>[ 0.236725] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.247176] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.247699] cpuidle: using governor menu <6>[ 0.259760] No ATAGs? <6>[ 0.262681] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.271779] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.281875] Serial: AMBA PL011 UART driver <6>[ 0.386786] iommu: Default domain type: Translated <6>[ 0.393992] vgaarb: loaded <5>[ 0.398230] SCSI subsystem initialized <6>[ 0.403091] usbcore: registered new interface driver usbfs <6>[ 0.409473] usbcore: registered new interface driver hub <6>[ 0.415628] usbcore: registered new device driver usb <6>[ 0.423448] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.429185] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.439527] PTP clock support registered <6>[ 0.447503] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.813139] NET: Registered protocol family 2 <6>[ 1.818488] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.828301] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.837833] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.846691] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.855021] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.862401] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.870014] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.878242] NET: Registered protocol family 1 <6>[ 1.883881] RPC: Registered named UNIX socket transport module. <6>[ 1.890709] RPC: Registered udp transport module. <6>[ 1.896157] RPC: Registered tcp transport module. <6>[ 1.901635] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.909021] PCI: CLS 0 bytes, default 64 <6>[ 1.914048] Trying to unpack rootfs image as initramfs... <6>[ 3.465299] Freeing initrd memory: 15696K <6>[ 3.470900] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available <5>[ 3.481723] Initialise system trusted keyrings <6>[ 3.487155] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 3.501094] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.508564] NFS: Registering the id_resolver key type <5>[ 3.514470] Key type id_resolver registered <5>[ 3.519384] Key type id_legacy registered <6>[ 3.524185] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.531851] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.540301] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.545843] Key type asymmetric registered <5>[ 3.550651] Asymmetric key parser 'x509' registered <6>[ 3.556346] bounce: pool size: 64 pages <6>[ 3.560915] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.569340] io scheduler mq-deadline registered <6>[ 3.574597] io scheduler kyber registered <6>[ 3.618970] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 3.627601] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 <6>[ 3.638808] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 3.647411] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 <6>[ 3.722783] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.733028] printk: console [ttyS2] disabled <6>[ 3.738115] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 43, base_baud = 1500000) is a 16550A <6>[ 3.748322] printk: console [ttyS2] enabled <6>[ 3.748322] printk: console [ttyS2] enabled <6>[ 3.758302] printk: bootconsole [uart0] disabled <6>[ 3.758302] printk: bootconsole [uart0] disabled <6>[ 3.771986] SuperH (H)SCI(F) driver initialized <6>[ 3.778860] msm_serial: driver initialized <6>[ 3.783979] STMicroelectronics ASC driver initialized <6>[ 3.791857] STM32 USART driver initialized <6>[ 3.816029] brd: module loaded <6>[ 3.826622] loop: module loaded <6>[ 3.846192] CAN device driver interface <6>[ 3.852123] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.860391] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.866234] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.873230] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.879586] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.889745] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 3.897055] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 3.907546] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.916156] usbcore: registered new interface driver pegasus <6>[ 3.922843] usbcore: registered new interface driver asix <6>[ 3.929234] usbcore: registered new interface driver ax88179_178a <6>[ 3.936375] usbcore: registered new interface driver cdc_ether <6>[ 3.943260] usbcore: registered new interface driver smsc75xx <6>[ 3.950064] usbcore: registered new interface driver smsc95xx <6>[ 3.956819] usbcore: registered new interface driver net1080 <6>[ 3.963499] usbcore: registered new interface driver cdc_subset <6>[ 3.970475] usbcore: registered new interface driver zaurus <6>[ 3.977075] usbcore: registered new interface driver cdc_ncm <4>[ 3.986727] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator <4>[ 3.995167] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator <6>[ 4.067822] dwc2 ff540000.usb: DWC OTG Controller <6>[ 4.073398] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1 <6>[ 4.081639] dwc2 ff540000.usb: irq 48, io mem 0xff540000 <6>[ 4.088682] hub 1-0:1.0: USB hub found <6>[ 4.093211] hub 1-0:1.0: 1 port detected <4>[ 4.098700] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator <4>[ 4.107123] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator <6>[ 4.257547] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM <6>[ 4.266106] dwc2 ff580000.usb: DWC OTG Controller <6>[ 4.271718] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2 <6>[ 4.279940] dwc2 ff580000.usb: irq 49, io mem 0xff580000 <6>[ 4.286886] hub 2-0:1.0: USB hub found <6>[ 4.291459] hub 2-0:1.0: 1 port detected <6>[ 4.297780] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.305375] ehci-pci: EHCI PCI platform driver <6>[ 4.310715] ehci-platform: EHCI generic platform driver <6>[ 4.317184] ehci-platform ff500000.usb: EHCI Host Controller <6>[ 4.323865] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3 <6>[ 4.333200] ehci-platform ff500000.usb: irq 47, io mem 0xff500000 <6>[ 4.367502] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 <6>[ 4.375487] hub 3-0:1.0: USB hub found <6>[ 4.380043] hub 3-0:1.0: 1 port detected <6>[ 4.385420] ehci-orion: EHCI orion driver <6>[ 4.390473] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.395442] ehci-st: EHCI STMicroelectronics driver <6>[ 4.401413] ehci-exynos: EHCI Exynos driver <6>[ 4.406569] ehci-atmel: EHCI Atmel driver <6>[ 4.411556] tegra-ehci: Tegra EHCI driver <6>[ 4.416552] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.423810] ohci-pci: OHCI PCI platform driver <6>[ 4.429147] ohci-platform: OHCI generic platform driver <6>[ 4.435534] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.440526] ohci-st: OHCI STMicroelectronics driver <6>[ 4.446463] ohci-atmel: OHCI Atmel driver <6>[ 4.452583] usbcore: registered new interface driver usb-storage <6>[ 4.467182] i2c /dev entries driver <6>[ 4.477674] VCC_DDR: supplied by vcc_sys <6>[ 4.484663] VCC_IO: supplied by vcc_sys <6>[ 4.491575] VDD_LOG: Bringing 1100000uV into 1000000-1000000uV <6>[ 4.500796] VDD_LOG: supplied by vcc_sys <6>[ 4.507766] VCC_20: supplied by vcc_sys <6>[ 4.514627] VCCIO_SD: supplied by VCC_IO <6>[ 4.522147] VDD10_LCD: supplied by VCC_IO <6>[ 4.530083] VCCA_CODEC: supplied by VCC_IO <6>[ 4.538170] VCCA_TP: supplied by vcc_sys <6>[ 4.545516] VCCIO_PMU: supplied by vcc_sys <6>[ 4.552738] VDD_10: supplied by VCC_20 <6>[ 4.560029] VCC_18: supplied by VCC_20 <6>[ 4.567299] VCC18_LCD: supplied by VCC_20 <6>[ 4.576424] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! <6>[ 4.585836] vdd_cpu: supplied by vcc_sys <6>[ 4.593166] vcc_flash: supplied by VCC_IO <6>[ 4.598562] vcc_sd: supplied by VCC_IO <6>[ 4.605341] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! <6>[ 4.614748] vdd_gpu: supplied by vcc_sys <4>[ 4.637775] dw_wdt ff800000.watchdog: No valid TOPs array specified <6>[ 4.654344] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 500000 KHz, changing to: 600000 KHz <6>[ 4.668790] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.675992] sdhci: Copyright(c) Pierre Ossman <6>[ 4.683342] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.691472] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.691674] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.692113] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.695261] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.695288] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller. <6>[ 4.695294] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a <6>[ 4.695315] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 40,32 bit host data width,256 deep fifo <6>[ 4.695947] dwmmc_rockchip ff0f0000.mmc: allocated mmc-pwrseq <6>[ 4.695950] mmc_host mmc0: card is non-removable. <6>[ 4.699680] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller. <6>[ 4.707842] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.707848] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 4.707853] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 4.707873] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 4.714431] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a <6>[ 4.714447] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo <6>[ 4.722708] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 4.722958] usbcore: registered new interface driver usbhid <6>[ 4.722960] usbhid: USB HID core driver <6>[ 4.724813] NET: Registered protocol family 10 <6>[ 4.730312] usb 3-1: new high-speed USB device number 2 using ehci-platform <6>[ 4.736986] Segment Routing with IPv6 <6>[ 4.830038] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 4.834624] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.874579] NET: Registered protocol family 17 <6>[ 4.879842] can: controller area network core <6>[ 4.885025] NET: Registered protocol family 29 <6>[ 4.890288] can: raw protocol <6>[ 4.893894] can: broadcast manager protocol <6>[ 4.898860] can: netlink gateway - max_hops=1 <5>[ 4.904183] Key type dns_resolver registered <6>[ 4.909302] ThumbEE CPU extension supported. <5>[ 4.914372] Registering SWP/SWPB emulation handler <5>[ 4.920152] Loading compiled-in X.509 certificates <6>[ 4.938818] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 4.944067] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 4.957290] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 4.965056] mmc0: new high speed MMC card at address 0001 <6>[ 4.965335] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). <6>[ 4.971762] mmcblk0: mmc0:0001 032GE4 29.1 GiB <6>[ 4.979587] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). <6>[ 4.979672] hub 3-1:1.0: USB hub found <6>[ 4.984942] hub 3-1:1.0: 4 ports detected <6>[ 4.985107] mmcblk0boot0: mmc0:0001 032GE4 partition 1 4.00 MiB <6>[ 4.985317] mmcblk0boot1: mmc0:0001 032GE4 partition 2 4.00 MiB <6>[ 4.991558] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). <6>[ 4.996084] mmcblk0rpmb: mmc0:0001 032GE4 partition 3 4.00 MiB, chardev (235:0) <6>[ 5.000821] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no). <3>[ 5.037000] rk_gmac-dwmac ff290000.ethernet: cannot get clock clk_mac_speed <6>[ 5.045081] rk_gmac-dwmac ff290000.ethernet: clock input from PHY <6>[ 5.057194] rk_gmac-dwmac ff290000.ethernet: init for RGMII <6>[ 5.063896] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35 <6>[ 5.072192] rk_gmac-dwmac ff290000.ethernet: DWMAC1000 <6>[ 5.078326] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported <6>[ 5.086968] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported <6>[ 5.095616] rk_gmac-dwmac ff290000.ethernet: COE Type 2 <6>[ 5.101753] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported <6>[ 5.109924] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported <6>[ 5.117454] rk_gmac-dwmac ff290000.ethernet: Normal descriptors <6>[ 5.124356] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled <6>[ 5.131159] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 5.142815] mmcblk0: p1 p2 <6>[ 5.269121] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) <6>[ 5.283429] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL) <3>[ 5.302041] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <6>[ 5.302097] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <3>[ 5.311104] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <3>[ 5.328300] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <6>[ 5.337828] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 5.345672] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 5.353372] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 5.359908] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 5.373998] rk_gmac-dwmac ff290000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL) <6>[ 5.387249] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 5.395465] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 5.396695] rk_gmac-dwmac ff290000.ethernet eth0: No Safety Features support found <6>[ 5.403159] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 5.403180] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <4>[ 5.411924] rk_gmac-dwmac ff290000.ethernet eth0: PTP not supported by HW <6>[ 5.437471] rk_gmac-dwmac ff290000.ethernet eth0: configuring for phy/rgmii link mode <6>[ 9.578845] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 9.608356] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 9.637528] Sending DHCP requests ., OK <6>[ 9.702394] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.22 <6>[ 9.711786] IP-Config: Complete: <6>[ 9.715751] device=eth0, hwaddr=4a:01:9c:e5:04:ff, ipaddr=192.168.201.22, mask=255.255.255.0, gw=192.168.201.1 <6>[ 9.727734] host=rk3288-rock2-square-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 9.736674] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 9.736677] nameserver0=192.168.201.1 <4>[ 9.750331] dw-apb-uart ff690000.serial: forbid DMA for kernel console <6>[ 9.758949] Freeing unused kernel memory: 2048K <6>[ 9.787598] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.878036] udevd[123]: starting version 3.2.9 <5>[ 9.884171] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.891946] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.899733] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 9.911628] udevd[123]: specified user 'tss' unknown <27>[ 9.917694] udevd[123]: specified group 'tss' unknown <30>[ 9.924625] udevd[124]: starting eudev-3.2.9 <6>[ 10.055184] rockchip-vop ff930000.vop: Adding to iommu group 0 <6>[ 10.062319] rockchip-vop ff940000.vop: Adding to iommu group 1 <6>[ 10.073275] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 10.091477] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 10.099196] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 10.105729] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 10.116981] rockchip-drm display-subsystem: bound ff930000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 10.150399] rockchip-drm display-subsystem: bound ff940000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 10.161059] dwhdmi-rockchip ff980000.hdmi: Detected HDMI TX controller v2.00a with HDCP (DWC MHL PHY) <6>[ 10.164318] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 10.184694] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <4>[ 10.186298] rtc-hym8563 0-0051: no valid clock/calendar values available <6>[ 10.192391] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 10.192408] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 10.200645] rtc-hym8563 0-0051: registered as rtc0 <6>[ 10.225907] rockchip-drm display-subsystem: bound ff980000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm]) <4>[ 10.233170] rtc-hym8563 0-0051: no valid clock/calendar values available <3>[ 10.244602] rtc-hym8563 0-0051: hctosys: unable to read the hardware clock <6>[ 10.244716] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 10.260483] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 10.261484] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0 <6>[ 10.283425] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 10.291135] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 10.297678] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 10.317324] dwmmc_rockchip ff0d0000.mmc: allocated mmc-pwrseq <6>[ 10.324069] mmc_host mmc1: card is non-removable. <6>[ 10.346258] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 10.369090] panfrost ffa30000.gpu: clock rate = 400000000 <6>[ 10.378232] rk3288-crypto ff8a0000.crypto: will run requests pump with realtime priority <6>[ 10.388430] panfrost ffa30000.gpu: mali-t760 id 0x750 major 0x0 minor 0x0 status 0x1 <4>[ 10.395723] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <6>[ 10.397376] panfrost ffa30000.gpu: features: 00000000,100277bf, issues: 00000000,24040400 <4>[ 10.405307] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) <6>[ 10.413245] panfrost ffa30000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 <4>[ 10.423411] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) <6>[ 10.433162] panfrost ffa30000.gpu: shader_present=0xf l2_present=0x1 <6>[ 10.447847] rk3288-crypto ff8a0000.crypto: Crypto Accelerator successfully registered <4>[ 10.458999] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <6>[ 10.466112] [drm] Initialized panfrost 1.1.0 20180908 for ffa30000.gpu on minor 1 done Saving random seed: OK Starting network: <6>[ 10.521674] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) ip: RTNETLINK answers: File exists <6>[ 10.536337] mmc1: new high speed SDIO card at address 0001 FAIL Starting dropbear sshd: <5>[ 10.563154] cfg80211: Loading compiled-in X.509 certificates for regulatory database OK /bin/sh: can't access tty; job control turned off / # <5>[ 10.596876] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 10.604554] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 10.614506] cfg80211: failed to load regulatory.db <6>[ 10.618752] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 10.630290] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11517175/environment . /lava-11517175/environment / # /lava-11517175/bin/lava-test-runner /lava-11517175/0 /lava-11517175/bin/lava-test-runner /lava-11517175/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11517175/0/tests/0_dmesg<8>[ 11.133038] + cat uuid + UUID=11517175_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.163703] <8>[ 11.185834] <8>[ 11.209734] + set +x <8>[ 11.220062] / # # export SHELL=/bin/sh #<6>[ 11.337758] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes / # export SHELL=/bin/sh. /lava-11517175/environment / # . /lava-11517175/environment/lava-11517175/bin/lava-test-runner /lava-11517175/1 / # /lava-11517175/bin/lava-test-runner /lava-11517175/1<3>[ 11.648967] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11517175/1/tests/1_bootrr + cat uuid + UUID=11517175_<8>[ 11.703227] 1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11517175/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-11517175/1/../bin/lava-test-case <8>[ 11.735090] /lava-11517175/1/../bin/lava-test-case <8>[ 11.758199] /lava-11517175/1/../bin/lava-test-case <8>[ 11.774383] /lava-11517175/1/../bin/lava-test-case <8>[ 11.799320] /lava-11517175/1/../bin/lava-test-case <8>[ 11.821512] /lava-11517175/1/../bin/lava-test-case <8>[ 11.840114] /lava-11517175/1/../bin/lava-test-case <8>[ 11.865630] /lava-11517175/1/../bin/lava-test-case <8>[ 11.889438] /lava-11517175/1/../bin/lava-test-case <8>[ 11.913592] + set +x <8>[ 11.922610] / #