Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 28C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.217 (1298 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp ${loadaddr} 1246968/tftp-deploy-f8x7h8qk/kernel/zImage tftp ${loadaddr} 1246968/tftp-deploy-f8x7h8qk/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.217; sending through gateway 172.16.1.4 Filename '1246968/tftp-deploy-f8x7h8qk/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### 10.6 MiB/s done Bytes transferred = 10562304 (a12b00 hex) => tftp ${initrd_addr} 1246968/tftp-deploy-f8x7h8qk/ramdisk/ramdisk.cpio.gz.uboot tftp ${initrd_addr} 1246968/tftp-deploy-f8x7h8qk/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.217; sending through gateway 172.16.1.4 Filename '1246968/tftp-deploy-f8x7h8qk/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################# 10 MiB/s done Bytes transferred = 10191515 (9b829b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp ${fdt_addr} 1246968/tftp-deploy-f8x7h8qk/dtb/imx7d-sdb.dtb tftp ${fdt_addr} 1246968/tftp-deploy-f8x7h8qk/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.217; sending through gateway 172.16.1.4 Filename '1246968/tftp-deploy-f8x7h8qk/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 7.3 MiB/s done Bytes transferred = 38143 (94ff hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz ${loadaddr} ${initrd_addr} ${fdt_addr} bootz ${loadaddr} ${initrd_addr} ${fdt_addr} Kernel image @ 0x80800000 [ 0x000000 - 0xa12b00 ] ## Loading init Ramdisk from Legacy Image at 83800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 10191451 Bytes = 9.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300c4fe Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.191-cip38 (KernelCI@build-j24648-arm-gcc-10-imx-v6-v7-defconfig-t4nv6) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Aug 28 00:27:59 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s51948 r8192 d21780 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933568K/1048576K available (14336K kernel code, 2028K rwdata, 4852K rodata, 1024K init, 6664K bss, 49472K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000011] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008286] Switching to timer-based delay loop, resolution 125ns <6>[ 0.015294] Switching to timer-based delay loop, resolution 41ns <6>[ 0.020978] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029114] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.041325] Console: colour dummy device 80x30 <4>[ 0.043724] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.051812] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.056145] ... MAX_LOCK_DEPTH: 48 <4>[ 0.060607] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.065276] ... CLASSHASH_SIZE: 4096 <4>[ 0.069882] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.074607] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.079362] ... CHAINHASH_SIZE: 32768 <4>[ 0.084057] memory used by lock dependency info: 4061 kB <4>[ 0.089774] memory used for stack traces: 2112 kB <4>[ 0.094820] per task-struct memory footprint: 1536 bytes <6>[ 0.100617] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.111220] CPU: Testing write buffer coherency: ok <6>[ 0.116351] pid_max: default: 32768 minimum: 301 <6>[ 0.121705] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.128874] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.141990] CPU0: update cpu_capacity 1024 <6>[ 0.143531] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.152454] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.157155] rcu: Hierarchical SRCU implementation. <6>[ 0.163695] smp: Bringing up secondary CPUs ... <6>[ 0.169581] smp: Brought up 1 node, 1 CPU <6>[ 0.171034] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.177748] CPU: All CPU(s) started in SVC mode. <6>[ 0.185392] devtmpfs: initialized <6>[ 0.228525] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.234838] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.243998] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.254079] pinctrl core: initialized pinctrl subsystem <6>[ 0.263723] NET: Registered protocol family 16 <6>[ 0.296606] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.307872] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.308203] cpuidle: using governor menu <6>[ 0.317431] No ATAGs? <6>[ 0.318765] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.326842] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.456580] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <6>[ 0.465150] imx7d-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.619445] vgaarb: loaded <5>[ 0.622015] SCSI subsystem initialized <6>[ 0.625632] usbcore: registered new interface driver usbfs <6>[ 0.629636] usbcore: registered new interface driver hub <6>[ 0.635303] usbcore: registered new device driver usb <4>[ 0.640878] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.649675] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.658078] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.665527] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.695533] i2c i2c-0: IMX I2C adapter registered <6>[ 0.714720] i2c i2c-1: IMX I2C adapter registered <6>[ 0.719439] i2c i2c-2: IMX I2C adapter registered <6>[ 0.738672] i2c i2c-3: IMX I2C adapter registered <6>[ 0.741820] mc: Linux media interface: v0.10 <6>[ 0.745510] videodev: Linux video capture interface: v2.00 <6>[ 0.751956] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.756399] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.765970] PTP clock support registered <6>[ 0.772034] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.780376] Bluetooth: Core ver 2.22 <6>[ 0.781514] NET: Registered protocol family 31 <6>[ 0.786114] Bluetooth: HCI device and connection manager initialized <6>[ 0.792951] Bluetooth: HCI socket layer initialized <6>[ 0.797945] Bluetooth: L2CAP socket layer initialized <6>[ 0.803464] Bluetooth: SCO socket layer initialized <6>[ 0.811329] clocksource: Switched to clocksource arch_sys_counter <5>[ 2.383459] VFS: Disk quotas dquot_6.6.0 <6>[ 2.385019] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.428049] NET: Registered protocol family 2 <6>[ 2.430433] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.440897] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 2.447496] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.455077] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 2.463984] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.469764] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 2.476413] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 2.484235] NET: Registered protocol family 1 <6>[ 2.490510] RPC: Registered named UNIX socket transport module. <6>[ 2.494314] RPC: Registered udp transport module. <6>[ 2.499138] RPC: Registered tcp transport module. <6>[ 2.504182] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.513251] PCI: CLS 0 bytes, default 64 <6>[ 2.516558] Trying to unpack rootfs image as initramfs... <6>[ 3.700986] Freeing initrd memory: 9956K <6>[ 3.704688] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 3.717148] Initialise system trusted keyrings <6>[ 3.720025] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <5>[ 3.756500] NFS: Registering the id_resolver key type <5>[ 3.759220] Key type id_resolver registered <5>[ 3.763638] Key type id_legacy registered <6>[ 3.768139] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.774899] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.782688] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. <6>[ 3.790995] fuse: init (API version 7.32) <5>[ 3.912360] Key type asymmetric registered <5>[ 3.914046] Asymmetric key parser 'x509' registered <6>[ 3.919328] bounce: pool size: 64 pages <6>[ 3.923549] io scheduler mq-deadline registered <6>[ 3.927990] io scheduler kyber registered <4>[ 3.943283] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 3.970959] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <4>[ 3.978280] imx-sdma 30bd0000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin <6>[ 3.993773] mxs-dma 33000000.dma-apbh: initialized <6>[ 4.009059] pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1 <6>[ 4.013955] pfuze100-regulator 0-0008: FAB: 0, FIN: 0 <6>[ 4.018218] pfuze100-regulator 0-0008: pfuze3000 found. <6>[ 4.055588] VLDO4: Bringing 3300000uV into 2800000-2800000uV <3>[ 4.064970] clk: failed to reparent uart1_src to pll_sys_main_240m_clk: -16 <6>[ 4.070452] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 58, base_baud = 1500000) is a IMX <6>[ 4.079419] printk: console [ttymxc0] enabled <6>[ 4.079419] printk: console [ttymxc0] enabled <6>[ 4.087850] printk: bootconsole [ec_imx6q0] disabled <6>[ 4.087850] printk: bootconsole [ec_imx6q0] disabled <6>[ 4.103462] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 67, base_baud = 15000000) is a IMX <6>[ 4.185466] brd: module loaded <6>[ 4.226603] loop: module loaded <6>[ 4.239914] gpio-expander@0 enforce active low on chipselect handle <6>[ 4.285476] CAN device driver interface <6>[ 4.305766] pps pps0: new PPS source ptp0 <6>[ 4.394282] fec 30be0000.ethernet eth0: registered PHC device 0 <6>[ 4.407312] pps pps1: new PPS source ptp1 <3>[ 4.414506] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 4.421817] fec 30bf0000.ethernet: Using random MAC address: 82:aa:b9:04:71:21 <6>[ 5.516980] fec 30bf0000.ethernet eth1: registered PHC device 1 <6>[ 5.526730] usbcore: registered new interface driver r8152 <6>[ 5.532871] usbcore: registered new interface driver lan78xx <6>[ 5.539004] usbcore: registered new interface driver asix <6>[ 5.544958] usbcore: registered new interface driver ax88179_178a <6>[ 5.551648] usbcore: registered new interface driver cdc_ether <6>[ 5.557956] usbcore: registered new interface driver smsc95xx <6>[ 5.564275] usbcore: registered new interface driver net1080 <6>[ 5.570384] usbcore: registered new interface driver cdc_subset <6>[ 5.576804] usbcore: registered new interface driver zaurus <6>[ 5.582865] usbcore: registered new interface driver MOSCHIP usb-ethernet driver <6>[ 5.590778] usbcore: registered new interface driver cdc_ncm <6>[ 5.596784] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 5.603650] ehci-pci: EHCI PCI platform driver <6>[ 5.608518] ehci-mxc: Freescale On-Chip EHCI Host driver <6>[ 5.615321] usbcore: registered new interface driver usb-storage <6>[ 5.633345] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 <4>[ 5.650335] ads7846 spi2.0: supply vcc not found, using dummy regulator <6>[ 5.660078] ads7846 spi2.0: touchscreen, irq 145 <6>[ 5.667918] input: ADS7846 Touchscreen as /devices/platform/soc/30800000.bus/30800000.spba-bus/30840000.spi/spi_master/spi2/spi2.0/input/input1 <6>[ 5.695748] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 <6>[ 5.702402] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0) <6>[ 5.712351] i2c /dev entries driver <6>[ 5.732849] Bluetooth: HCI UART driver ver 2.3 <6>[ 5.737599] Bluetooth: HCI UART protocol H4 registered <6>[ 5.743189] Bluetooth: HCI UART protocol LL registered <3>[ 5.749661] CPUidle arm: CPU 0 failed to init idle CPU ops <6>[ 5.758114] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.764655] sdhci: Copyright(c) Pierre Ossman <6>[ 5.769301] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.778561] sdhci-esdhc-imx 30b40000.mmc: Got CD GPIO <6>[ 5.788166] caam 30900000.crypto: Entropy delay = 3200 <6>[ 5.808123] sdhci-esdhc-imx 30b40000.mmc: Got WP GPIO <6>[ 5.853132] caam 30900000.crypto: Instantiated RNG4 SH0 <6>[ 5.912538] caam 30900000.crypto: Instantiated RNG4 SH1 <6>[ 5.920760] caam 30900000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 5.927865] caam 30900000.crypto: job rings = 3, qi = 0 <6>[ 5.946394] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <6>[ 5.968286] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA <6>[ 5.998879] caam algorithms registered in /proc/crypto <6>[ 6.015682] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 6.024705] caam 30900000.crypto: registering rng-caam <6>[ 6.030885] mmc0: new high speed SDHC card at address aaaa <6>[ 6.047578] usbcore: registered new interface driver usbhid <6>[ 6.053619] usbhid: USB HID core driver <6>[ 6.057828] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <6>[ 6.067332] mmcblk0: mmc0:aaaa SA16G 14.8 GiB <6>[ 6.092771] mmcblk0: p1 p2 <4>[ 6.120536] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 6.130013] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 6.139460] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <5>[ 6.216983] random: crng init done <6>[ 6.275502] NET: Registered protocol family 10 <6>[ 6.295237] Segment Routing with IPv6 <6>[ 6.299336] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.314390] mmc1: new ultra high speed SDR104 SDIO card at address 0001 <6>[ 6.324185] NET: Registered protocol family 17 <6>[ 6.328969] can: controller area network core <6>[ 6.337335] NET: Registered protocol family 29 <6>[ 6.342215] can: raw protocol <6>[ 6.345689] can: broadcast manager protocol <6>[ 6.350203] can: netlink gateway - max_hops=1 <5>[ 6.355745] Key type dns_resolver registered <6>[ 6.361897] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 2 mkt segment 0 supported-hw 0x4 0x1 <5>[ 6.384665] Registering SWP/SWPB emulation handler <5>[ 6.390398] Loading compiled-in X.509 certificates <6>[ 6.641482] vdd1p0d: supplied by SW2 <6>[ 6.646155] vdd1p2: supplied by SW2 <6>[ 6.671786] [drm] Initialized mxsfb-drm 1.0.0 20160824 for 30730000.lcdif on minor 0 <6>[ 6.727560] Console: switching to colour frame buffer device 60x34 <6>[ 6.750846] mxsfb 30730000.lcdif: [drm] fb0: mxsfb-drmdrmfb frame buffer device <4>[ 6.761093] imx_usb 30b10000.usb: No over current polarity defined <4>[ 6.896763] imx_usb 30b20000.usb: No over current polarity defined <6>[ 6.908199] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 6.914593] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 6.951656] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 6.960138] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 6.969019] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 6.976656] usb usb1: Product: EHCI Host Controller <6>[ 6.981915] usb usb1: Manufacturer: Linux 5.10.191-cip38 ehci_hcd <6>[ 6.988304] usb usb1: SerialNumber: ci_hdrc.1 <6>[ 6.998568] hub 1-0:1.0: USB hub found <6>[ 7.003357] hub 1-0:1.0: 1 port detected <6>[ 7.018442] imx_thermal 30360000.anatop:tempmon: Commercial CPU temperature grade - max:95C critical:90C passive:85C <4>[ 7.184002] usb_phy_generic usbphynop3: supply vcc not found, using dummy regulator <4>[ 7.193011] usb_phy_generic usbphynop3: dummy supplies not allowed for exclusive requests <6>[ 7.207275] imx6q-pcie 33800000.pcie: host bridge /soc/bus@30800000/pcie@33800000 ranges: <6>[ 7.222831] input: gpio-keys as /devices/platform/gpio-keys/input/input3 <6>[ 7.230549] imx6q-pcie 33800000.pcie: IO 0x004ff80000..0x004ff8ffff -> 0x0000000000 <6>[ 7.241906] imx6q-pcie 33800000.pcie: MEM 0x0040000000..0x004fefffff -> 0x0040000000 <6>[ 8.491842] imx6q-pcie 33800000.pcie: Phy link never came up <6>[ 8.498921] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 <6>[ 8.505733] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 8.511571] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 8.518051] pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fefffff] <6>[ 8.526457] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 <6>[ 8.532913] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] <6>[ 8.539562] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] <6>[ 8.547427] pci 0000:00:00.0: supports D1 <6>[ 8.551890] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold <6>[ 8.562556] PCI: bus0: Fast back to back transfers disabled <6>[ 8.571077] PCI: bus1: Fast back to back transfers enabled <6>[ 8.577144] pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x400fffff] <6>[ 8.584317] pci 0000:00:00.0: BAR 6: assigned [mem 0x40100000-0x4010ffff pref] <6>[ 8.591923] pci 0000:00:00.0: PCI bridge to [bus 01-ff] <6>[ 8.612622] Generic PHY 30be0000.ethernet-1:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL) <6>[ 8.638664] Generic PHY 30be0000.ethernet-1:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL) <6>[ 12.752852] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.761646] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 12.792657] Sending DHCP requests .., OK <6>[ 15.715625] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.217 <6>[ 15.723591] IP-Config: Complete: <6>[ 15.727114] device=eth0, hwaddr=00:04:9f:05:b3:72, ipaddr=172.16.1.217, mask=255.255.255.0, gw=172.16.1.4 <6>[ 15.737453] host=172.16.1.217, domain=example.org, nis-domain=(none) <6>[ 15.744578] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 15.744598] nameserver0=172.16.1.4 <5>[ 15.770397] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 15.837202] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 15.847481] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <4>[ 15.856538] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db <6>[ 15.874594] ALSA device list: <6>[ 15.877865] #0: wm8960-audio <6>[ 15.885366] Freeing unused kernel memory: 1024K <6>[ 15.891810] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.290650] udevd[220]: starting version 3.2.9 <27>[ 16.312432] udevd[220]: specified user 'tss' unknown <27>[ 16.318006] udevd[220]: specified group 'tss' unknown <30>[ 16.343926] udevd[221]: starting eudev-3.2.9 <6>[ 18.309987] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 18.378984] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <4>[ 18.389164] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac4339-sdio.bin done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1246968/environment . /lava-1246968/environment / # /lava-1246968/bin/lava-test-runner /lava-1246968/0 /lava-1246968/bin/lava-test-runner /lava-1246968/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1246968/0/tests/0_dmesg + cat uuid + UUID=1246968_1.5.2.4.1<8>[ 25.258092] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 25.363532] <8>[ 25.457438] <8>[ 25.551947] + set +x <8>[ 25.563851] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1246968/environment / # . /lava-1246968/environment/lava-1246968/bin/lava-test-runner /lava-1246968/1 / # /lava-1246968/bin/lava-test-runner /lava-1246968/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1246968/1/tests/1_bootrr + cat uuid + UUID=1246968_1.5.2.4.5<8>[ 31.377874] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1246968/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-1246968/1/../bin/lava-test-case <8>[ 31.503860] /lava-1246968/1/../bin/lava-test-case <8>[ 32.610968] /lava-1246968/1/../bin/lava-test-case <8>[ 32.660751] + set +x <8>[ 32.697015] / #