Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.9 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1001791/tftp-deploy-b9odmc80/kernel/zImage tftp 0x82000000 1001791/tftp-deploy-b9odmc80/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '1001791/tftp-deploy-b9odmc80/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 5.2 MiB/s done Bytes transferred = 4607056 (464c50 hex) => tftp 0x83000000 1001791/tftp-deploy-b9odmc80/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1001791/tftp-deploy-b9odmc80/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '1001791/tftp-deploy-b9odmc80/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.2 MiB/s done Bytes transferred = 14169696 (d83660 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1001791/tftp-deploy-b9odmc80/dtb/am335x-boneblack.dtb tftp 0x88000000 1001791/tftp-deploy-b9odmc80/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '1001791/tftp-deploy-b9odmc80/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.3 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-08-28 0:58:39 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14169632 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.191-cip38 (KernelCI@build-j24646-arm-gcc-10-omap2plus-defconfig-7nbbc) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Aug 28 00:31:45 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472028K/522240K available (9216K kernel code, 1027K rwdata, 2176K rodata, 1024K init, 278K bss, 33828K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008342] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018568] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030229] Console: colour dummy device 80x30 <3>[ 0.035103] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042162] This ensures that you still see kernel messages. Please <3>[ 0.048889] update your kernel commandline. <6>[ 0.053492] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095548] CPU: Testing write buffer coherency: ok <6>[ 0.100930] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106395] pid_max: default: 32768 minimum: 301 <6>[ 0.111561] LSM: Security Framework initializing <6>[ 0.116661] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124478] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134157] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140733] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147937] rcu: Hierarchical SRCU implementation. <6>[ 0.153743] smp: Bringing up secondary CPUs ... <6>[ 0.158682] smp: Brought up 1 node, 1 CPU <6>[ 0.163132] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169874] CPU: All CPU(s) started in SVC mode. <6>[ 0.175636] devtmpfs: initialized <6>[ 0.191350] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199888] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210324] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218970] pinctrl core: initialized pinctrl subsystem <6>[ 0.226525] NET: Registered protocol family 16 <6>[ 0.234149] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260589] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266684] audit: initializing netlink subsys (disabled) <6>[ 0.273752] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273766] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280383] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287103] cpuidle: using governor menu <5>[ 1.178351] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.305288] No ATAGs? <6>[ 1.307915] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.332625] Kprobes globally optimized <6>[ 1.345863] iommu: Default domain type: Translated <6>[ 1.353197] vgaarb: loaded <5>[ 1.356793] SCSI subsystem initialized <6>[ 1.362112] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.367498] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.377286] PTP clock support registered <6>[ 1.382867] clocksource: Switched to clocksource dmtimer <5>[ 2.054937] VFS: Disk quotas dquot_6.6.0 <6>[ 2.059350] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.076341] NET: Registered protocol family 2 <6>[ 2.081406] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.090121] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.099078] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.107374] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.115055] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.121977] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.129012] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.136634] NET: Registered protocol family 1 <6>[ 2.142435] RPC: Registered named UNIX socket transport module. <6>[ 2.148901] RPC: Registered udp transport module. <6>[ 2.154029] RPC: Registered tcp transport module. <6>[ 2.159135] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.166063] PCI: CLS 0 bytes, default 64 <6>[ 2.171085] Trying to unpack rootfs image as initramfs... <6>[ 3.158643] Freeing initrd memory: 13840K <6>[ 3.164412] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.174827] Initialise system trusted keyrings <6>[ 3.180120] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.188390] NFS: Registering the id_resolver key type <5>[ 3.194003] Key type id_resolver registered <5>[ 3.198577] Key type id_legacy registered <6>[ 3.203049] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.211010] Key type asymmetric registered <5>[ 3.215547] Asymmetric key parser 'x509' registered <6>[ 3.220847] io scheduler mq-deadline registered <6>[ 3.225796] io scheduler kyber registered <3>[ 3.365966] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.374658] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.484984] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.527503] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.600329] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.609035] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.669793] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.678488] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.696156] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.704839] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.769191] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.777758] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.805451] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.819956] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.830831] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.840259] printk: console [ttyS0] enabled <6>[ 3.840259] printk: console [ttyS0] enabled <6>[ 3.849336] printk: bootconsole [omap8250] disabled <6>[ 3.849336] printk: bootconsole [omap8250] disabled <6>[ 3.873245] brd: module loaded <6>[ 3.884055] loop: module loaded <3>[ 3.889526] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.962882] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <3>[ 3.971128] mdio_bus 4a101000.mdio: MDIO device at address 0 is missing. <6>[ 3.978527] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.985224] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.990949] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.998481] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.007472] i2c /dev entries driver <5>[ 4.013072] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.020916] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.027466] sdhci: Copyright(c) Pierre Ossman <6>[ 4.032869] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.041095] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.050836] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.059288] Initializing XFRM netlink socket <6>[ 4.064162] NET: Registered protocol family 10 <6>[ 4.070534] Segment Routing with IPv6 <6>[ 4.074721] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.081688] NET: Registered protocol family 17 <6>[ 4.086535] NET: Registered protocol family 15 <5>[ 4.091383] Key type dns_resolver registered <6>[ 4.096581] oprofile: using arm/armv7 <6>[ 4.100625] ThumbEE CPU extension supported. <5>[ 4.105275] Registering SWP/SWPB emulation handler <3>[ 4.110753] omap_voltage_late_init: Voltage driver support not added <3>[ 4.117475] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.125905] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.134597] SmartReflex Class3 initialized <6>[ 4.139654] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.148612] Loading compiled-in X.509 certificates <6>[ 4.173554] OMAP GPIO hardware version 0.1 <4>[ 4.203530] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.217143] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.225709] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.232059] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.242104] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.253559] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.262573] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.267808] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.281643] mmc1: new high speed MMC card at address 0001 <6>[ 4.288502] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.294077] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.300753] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.307370] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.316887] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.325922] mmcblk1: p1 <6>[ 4.334230] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <3>[ 4.342988] cpsw 4a100000.ethernet: phy \"/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0\" not found on slave 0 <6>[ 24.372813] Waiting up to 100 more seconds for network. <6>[ 44.382801] Waiting up to 80 more seconds for network. <6>[ 64.392799] Waiting up to 60 more seconds for network. <6>[ 84.402802] Waiting up to 40 more seconds for network. <6>[ 104.412799] Waiting up to 20 more seconds for network. <5>[ 124.392815] Sending DHCP requests ...... timed out! <3>[ 203.820210] IP-Config: Reopening network devices... <6>[ 203.825531] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <3>[ 203.834245] cpsw 4a100000.ethernet: phy \"/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0\" not found on slave 0 <6>[ 223.862812] Waiting up to 100 more seconds for network. <6>[ 243.872800] Waiting up to 80 more seconds for network. <5>[ 253.162821] random: crng init done