Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.91 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 380562/tftp-deploy-1akob7gb/kernel/Image tftp 0x82000000 380562/tftp-deploy-1akob7gb/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '380562/tftp-deploy-1akob7gb/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 5.7 MiB/s done Bytes transferred = 31851008 (1e60200 hex) => tftp 0x90080000 380562/tftp-deploy-1akob7gb/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 380562/tftp-deploy-1akob7gb/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '380562/tftp-deploy-1akob7gb/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 13.9 MiB/s done Bytes transferred = 18916360 (120a408 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 380562/tftp-deploy-1akob7gb/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 380562/tftp-deploy-1akob7gb/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '380562/tftp-deploy-1akob7gb/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 4 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2023-09-19 14:40:59 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18916296 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.194-cip39 (KernelCI@build-j50772-arm64-gcc-10-defconfig-nxhbx) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Sep 19 14:15:40 UTC 2023 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7feb00-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 23 pages/cpu s56664 r8192 d29352 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3897752K/4126720K available (14528K kernel code, 2816K rwdata, 7648K rodata, 6016K init, 514K bss, 196200K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000003] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008719] Console: colour dummy device 80x25 <6>[ 0.013507] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024227] pid_max: default: 32768 minimum: 301 <6>[ 0.029185] LSM: Security Framework initializing <6>[ 0.034155] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041910] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050971] rcu: Hierarchical SRCU implementation. <6>[ 0.056209] Platform MSI: gic-its@6020000 domain created <6>[ 0.061907] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069763] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075886] EFI services will not be available. <6>[ 0.080825] smp: Bringing up secondary CPUs ... <6>[ 0.085926] Detected PIPT I-cache on CPU1 <6>[ 0.085946] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.085952] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.085977] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.086031] smp: Brought up 1 node, 2 CPUs <6>[ 0.116345] SMP: Total of 2 processors activated. <6>[ 0.121357] CPU features: detected: 32-bit EL0 Support <6>[ 0.126815] CPU features: detected: CRC32 instructions <6>[ 0.132266] CPU features: detected: 32-bit EL1 Support <6>[ 0.148796] CPU: All CPU(s) started at EL2 <6>[ 0.153214] alternatives: patching kernel code <6>[ 0.158699] devtmpfs: initialized <4>[ 0.164366] KASLR disabled due to lack of seed <6>[ 0.169226] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.179335] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.187021] pinctrl core: initialized pinctrl subsystem <6>[ 0.193186] DMI not present or invalid. <6>[ 0.197703] NET: Registered protocol family 16 <6>[ 0.203212] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210706] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218950] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.227228] audit: initializing netlink subsys (disabled) <5>[ 0.233063] audit: type=2000 audit(0.148:1): state=initialized audit_enabled=0 res=1 <6>[ 0.233583] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.241150] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.247699] cpuidle: using governor menu <6>[ 0.258874] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.266015] ASID allocator initialised with 65536 entries <6>[ 0.272396] Serial: AMBA PL011 UART driver <6>[ 0.287492] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.295141] SoC family: QorIQ LS1028A <6>[ 0.299095] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.311685] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.318724] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.325754] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.332783] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.340538] cryptd: max_cpu_qlen set to 1000 <6>[ 0.346470] ACPI: Interpreter disabled. <6>[ 0.351569] iommu: Default domain type: Translated <6>[ 0.356866] vgaarb: loaded <5>[ 0.360014] SCSI subsystem initialized <6>[ 0.364312] usbcore: registered new interface driver usbfs <6>[ 0.370125] usbcore: registered new interface driver hub <6>[ 0.375806] usbcore: registered new device driver usb <6>[ 0.381424] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.389368] i2c i2c-0: IMX I2C adapter registered <6>[ 0.394543] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.402230] i2c i2c-1: IMX I2C adapter registered <6>[ 0.407323] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.415102] i2c i2c-2: IMX I2C adapter registered <6>[ 0.420384] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.425682] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.435174] PTP clock support registered <6>[ 0.439460] EDAC MC: Ver: 3.0.0 <6>[ 0.443617] FPGA manager framework <6>[ 0.447350] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.454171] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.460696] VFS: Disk quotas dquot_6.6.0 <6>[ 0.464950] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.472255] pnp: PnP ACPI: disabled <6>[ 0.479256] NET: Registered protocol family 2 <6>[ 0.484220] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.493275] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.502200] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.510548] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.518550] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.525511] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.532564] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.540121] NET: Registered protocol family 1 <6>[ 0.545080] RPC: Registered named UNIX socket transport module. <6>[ 0.551329] RPC: Registered udp transport module. <6>[ 0.556353] RPC: Registered tcp transport module. <6>[ 0.561364] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.568134] PCI: CLS 0 bytes, default 64 <6>[ 0.572448] Unpacking initramfs... <6>[ 1.206618] Freeing initrd memory: 18468K <6>[ 1.211264] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.219961] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.225134] kvm [1]: GICv3: no GICV resource entry <6>[ 1.230242] kvm [1]: disabling GICv2 emulation <6>[ 1.235005] kvm [1]: GIC system register CPU interface enabled <6>[ 1.241188] kvm [1]: vgic interrupt IRQ9 <6>[ 1.245473] kvm [1]: Hyp mode initialized successfully <5>[ 1.251902] Initialise system trusted keyrings <6>[ 1.256746] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.266743] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.273307] NFS: Registering the id_resolver key type <5>[ 1.278697] Key type id_resolver registered <5>[ 1.283182] Key type id_legacy registered <6>[ 1.287538] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.294568] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.302388] 9p: Installing v9fs 9p2000 file system support <5>[ 1.339188] Key type asymmetric registered <5>[ 1.343592] Asymmetric key parser 'x509' registered <6>[ 1.348800] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.356532] io scheduler mq-deadline registered <6>[ 1.361367] io scheduler kyber registered <6>[ 1.370655] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.378762] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 1.387909] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 1.397055] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 1.406200] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 1.415345] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 1.424489] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 1.433636] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 1.442820] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.451932] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.459227] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.464765] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 1.475480] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 1.486635] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.497359] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.508518] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.519234] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.530388] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 1.541120] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.547478] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.558288] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.569531] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.580599] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.592119] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.597927] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.608204] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.619081] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.625433] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.636239] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.647483] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.658550] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.670070] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.675878] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.686157] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.696989] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.703344] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.714150] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.725403] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.731320] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.737674] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.748483] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.759736] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.765646] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.771999] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.782804] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.794057] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.799969] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.806323] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.817129] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.828371] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.839185] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.845098] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.851449] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.862254] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.873510] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.880145] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.886512] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.894470] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 1.902479] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 1.909827] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.917496] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.926379] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.935349] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.942382] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.948184] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.954689] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.965614] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.971995] pci 0001:00:00.0: supports D1 D2 <6>[ 1.976568] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.984383] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.991334] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.996756] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.004418] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.013298] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.022250] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 2.029282] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 2.035085] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 2.044397] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.055305] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.061683] pci 0002:00:00.0: supports D1 D2 <6>[ 2.066256] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.074034] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.080982] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 2.086983] EINJ: ACPI disabled. <6>[ 2.098298] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.106266] printk: console [ttyS0] disabled <6>[ 2.110884] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.120045] printk: console [ttyS0] enabled <6>[ 2.120045] printk: console [ttyS0] enabled <6>[ 2.128986] printk: bootconsole [ns16550a0] disabled <6>[ 2.128986] printk: bootconsole [ns16550a0] disabled <6>[ 2.139817] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.149189] SuperH (H)SCI(F) driver initialized <6>[ 2.154303] msm_serial: driver initialized <6>[ 2.159031] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 2.169568] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.176308] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.181204] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.186795] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.192388] arm-smmu 5000000.iommu: nested translation <5>[ 2.197894] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.205320] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.212141] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.218867] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.225593] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 2.235693] loop: module loaded <6>[ 2.244311] megasas: 07.714.04.00-rc1 <6>[ 2.250366] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.265510] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.278335] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.285424] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 2.290932] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.298533] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 2.306495] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 2.314509] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 2.322506] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 2.330510] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.338500] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.346498] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.356234] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.362035] thunder_xcv, ver 1.0 <6>[ 2.365560] thunder_bgx, ver 1.0 <6>[ 2.369080] nicpf, ver 1.0 <6>[ 2.372562] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.486190] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 2.492703] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using ce:a0:18:b5:d2:b7 <6>[ 2.501528] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 86:3c:b6:c3:10:10 <6>[ 2.520844] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.634185] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.641569] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.647937] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.758185] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.764988] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.771351] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.882185] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.888982] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.895406] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 3.006201] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 3.013384] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 3.019675] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 3.026591] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 3.035594] pps pps0: new PPS source ptp0 <6>[ 3.040337] hclge is initializing <6>[ 3.043940] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 3.051455] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 3.057075] e1000: Intel(R) PRO/1000 Network Driver <6>[ 3.062232] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 3.068289] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.073533] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.079765] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.085445] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.091320] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 3.097872] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 3.104272] sky2: driver version 1.30 <6>[ 3.108845] VFIO - User Level meta-driver version: 0.3 <6>[ 3.114617] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 3.120469] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 3.127072] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.133902] ehci-pci: EHCI PCI platform driver <6>[ 3.138643] ehci-platform: EHCI generic platform driver <6>[ 3.144224] ehci-orion: EHCI orion driver <6>[ 3.148565] ehci-exynos: EHCI Exynos driver <6>[ 3.153074] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.159556] ohci-pci: OHCI PCI platform driver <6>[ 3.164300] ohci-platform: OHCI generic platform driver <6>[ 3.169871] ohci-exynos: OHCI Exynos driver <6>[ 3.174557] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.180339] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.188430] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.198147] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 3.204435] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.210209] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.218162] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.225286] hub 1-0:1.0: USB hub found <6>[ 3.229329] hub 1-0:1.0: 1 port detected <6>[ 3.233692] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.242312] hub 2-0:1.0: USB hub found <6>[ 3.246349] hub 2-0:1.0: 1 port detected <6>[ 3.250742] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.256527] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 3.264614] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.274330] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 3.280624] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.286395] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 3.294347] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.301414] hub 3-0:1.0: USB hub found <6>[ 3.305451] hub 3-0:1.0: 1 port detected <6>[ 3.309803] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.318416] hub 4-0:1.0: USB hub found <6>[ 3.322452] hub 4-0:1.0: 1 port detected <6>[ 3.327075] usbcore: registered new interface driver usb-storage <6>[ 3.335019] i2c /dev entries driver <6>[ 3.341660] sp805-wdt c000000.watchdog: registration successful <6>[ 3.347965] sp805-wdt c010000.watchdog: registration successful <6>[ 3.355362] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 3.364122] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.370608] sdhci: Copyright(c) Pierre Ossman <6>[ 3.375559] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.382444] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.388878] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 3.389467] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 3.394840] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.408025] usbcore: registered new interface driver usbhid <6>[ 3.413897] usbhid: USB HID core driver <6>[ 3.420776] NET: Registered protocol family 17 <6>[ 3.425613] 9pnet: Installing 9P2000 support <6>[ 3.426188] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <5>[ 3.430298] Key type dns_resolver registered <6>[ 3.437407] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 3.442042] registered taskstats version 1 <5>[ 3.453408] Loading compiled-in X.509 certificates <6>[ 3.460801] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 3.468637] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 3.474657] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 3.480824] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 3.486820] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 3.495549] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.538777] mmc0: new HS400 MMC card at address 0001 <6>[ 3.544424] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 3.549427] mmcblk0boot0: mmc0:0001 S0J56X partition 1 31.5 MiB <6>[ 3.555926] mmcblk0boot1: mmc0:0001 S0J56X partition 2 31.5 MiB <6>[ 3.562247] mmcblk0rpmb: mmc0:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 3.563585] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.570935] mmcblk0: p1 p2 <6>[ 3.583517] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.583571] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.781540] hub 3-1:1.0: USB hub found <6>[ 3.785771] hub 3-1:1.0: 7 ports detected <6>[ 6.663160] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.694229] Sending DHCP requests ., OK <6>[ 6.714428] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.91 <6>[ 6.722437] IP-Config: Complete: <6>[ 6.725959] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.91, mask=255.255.255.0, gw=172.16.0.254 <6>[ 6.736396] host=172.16.0.91, domain=lava.lan, nis-domain=(none) <6>[ 6.743158] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 6.743171] nameserver0=8.8.8.8 <6>[ 6.754054] ALSA device list: <6>[ 6.757398] No soundcards found. <6>[ 6.764816] Freeing unused kernel memory: 6016K <6>[ 6.769916] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.829981] udevd[125]: starting version 3.2.9 <5>[ 6.835210] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.842165] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.849002] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.858491] udevd[125]: specified user 'tss' unknown <27>[ 6.863879] udevd[125]: specified group 'tss' unknown <30>[ 6.870150] udevd[126]: starting eudev-3.2.9 <27>[ 7.083813] udevd[136]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 7.096180] NET: Registered protocol family 10 <6>[ 7.126994] mali-dp f080000.display: Adding to iommu group 13 <4>[ 7.134900] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 7.153357] Segment Routing with IPv6 <4>[ 7.178016] wm8904 2-001a: supply DCVDD not found, using dummy regulator <28>[ 7.181410] udevd[136]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <4>[ 7.192383] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 7.202042] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 7.209005] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 7.216047] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 7.224306] mscc_felix 0000:00:00.5: Adding to iommu group 14 <4>[ 7.233213] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 7.240804] wm8904 2-001a: revision A <6>[ 7.245342] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.263278] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 7.272848] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 7.280025] mscc_felix 0000:00:00.5: device is disabled, skipping <6>[ 7.339662] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 7.349844] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 7.350070] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 7.357224] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 7.386241] rtc-rv8803 0-0032: registered as rtc0 <4>[ 7.401333] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.411268] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <3>[ 7.416032] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 7.515050] caam 8000000.crypto: Entropy delay = 3200 <6>[ 7.543722] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 7.562168] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 7.567688] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 7.574872] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 7.607526] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 7.613861] caam algorithms registered in /proc/crypto <6>[ 7.620180] caam 8000000.crypto: registering rng-caam <6>[ 7.625822] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 7.631870] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 7.637878] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.685904] random: crng init done <5>[ 7.689725] random: 4 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-380562/environment . /lava-380562/environment / # /lava-380562/bin/lava-test-runner /lava-380562/0 /lava-380562/bin/lava-test-runner /lava-380562/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 8.242113] d /lava-380562/0/tests/0_dmesg + cat uuid + UUID=380562_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.261901] <8>[ 8.281982] <8>[ 8.301427] + set +x <8>[ 8.311002] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-380562/environment / # . /lava-380562/environment/lava-380562/bin/lava-test-runner /lava-380562/1 / # /lava-380562/bin/lava-test-runner /lava-380562/1 + export 'TESTRUN_ID=1_bootrr' + <8>[ 8.765054] cd /lava-380562/1/tests/1_bootrr + cat uuid + UUID=380562_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-380562/1/../bin:/sbin:/<8>[ 8.785798] usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-380562/1/../bin/lava-test-case /lava-<8>[ 8.803706] 380562/1/../bin/lava-test-case /lava-380562/1/../bin/lava-test-<8>[ 8.817996] case /lava-380562/1/../bin/lava-test-case <8>[ 8.839532] /lava-380562/1/../bin/lava-test-case <8>[ 8.856621] /lava-380562/1/../bin/lava-test-case <8>[ 8.871330] /lava-380562/1/../bin/lava-test-case <8>[ 8.890132] /lava-380562/1/../bin/lava-test-case <8>[ 8.907243] /lava-380562/1/../bin/lava-test-case <8>[ 8.926075] /lava-380562/1/../bin/lava-test-case <8>[ 8.942961] /lava-380562/1/../bin/lava-test-case <8>[ 8.960100] /lava-380562/1/../bin/lava-test-case <8>[ 8.974702] /lava-380562/1/../bin/lava-test-case <8>[ 8.991661] /lava-380562/1/../bin/lava-test-case <8>[ 9.005930] /lava-380562/1/../bin/lava-test-case <8>[ 9.025897] /lava-380562/1/../bin/lava-test-case <8>[ 9.041811] /lava-380562/1/../bin/lava-test-case <8>[ 9.059370] /lava-380562/1/../bin/lava-test-case <8>[ 9.076509] /lava-380562/1/../bin/lava-test-case <8>[ 9.091518] /lava-380562/1/../bin/lava-test-case <8>[ 9.109273] /lava-380562/1/../bin/lava-test-case <8>[ 9.128106] /lava-380562/1/../bin/lava-test-case <8>[ 9.145562] /lava-380562/1/../bin/lava-test-case <8>[ 9.160803] /lava-380562/1/../bin/lava-test-case <8>[ 9.178710] /lava-380562/1/../bin/lava-test-case <8>[ 9.196807] /lava-380562/1/../bin/lava-test-case <8>[ 9.214502] /lava-380562/1/../bin/lava-test-case <8>[ 9.229330] /lava-380562/1/../bin/lava-test-case <8>[ 9.246735] /lava-380562/1/../bin/lava-test-case <8>[ 9.261264] /lava-380562/1/../bin/lava-test-case <8>[ 9.278733] /lava-380562/1/../bin/lava-test-case <8>[ 9.296007] /lava-380562/1/../bin/lava-test-case <8>[ 9.312908] /lava-380562/1/../bin/lava-test-case <8>[ 9.328026] /lava-380562/1/../bin/lava-test-case <8>[ 9.345234] /lava-380562/1/../bin/lava-test-case <8>[ 9.359961] /lava-380562/1/../bin/lava-test-case <8>[ 9.377259] /lava-380562/1/../bin/lava-test-case <8>[ 9.392423] /lava-380562/1/../bin/lava-test-case <8>[ 9.410011] /lava-380562/1/../bin/lava-test-case <8>[ 9.430123] /lava-380562/1/../bin/lava-test-case <8>[ 9.446918] /lava-380562/1/../bin/lava-test-case <8>[ 9.464396] /lava-380562/1/../bin/lava-test-case <8>[ 9.481813] /lava-380562/1/../bin/lava-test-case <8>[ 9.496953] /lava-380562/1/../bin/lava-test-case <8>[ 9.514676] /lava-380562/1/../bin/lava-test-case <8>[ 9.529935] /lava-380562/1/../bin/lava-test-case <8>[ 9.547415] /lava-380562/1/../bin/lava-test-case <8>[ 9.562099] /lava-380562/1/../bin/lava-test-case <8>[ 9.579929] /lava-380562/1/../bin/lava-test-case <8>[ 9.597368] /lava-380562/1/../bin/lava-test-case <8>[ 9.615869] /lava-380562/1/../bin/lava-test-case <8>[ 9.633949] /lava-380562/1/../bin/lava-test-case <8>[ 9.650748] /lava-380562/1/../bin/lava-test-case <8>[ 9.665508] /lava-380562/1/../bin/lava-test-case <8>[ 9.683650] /lava-380562/1/../bin/lava-test-case <8>[ 9.701594] /lava-380562/1/../bin/lava-test-case <8>[ 9.717304] /lava-380562/1/../bin/lava-test-case <8>[ 9.734807] /lava-380562/1/../bin/lava-test-case <8>[ 9.749397] /lava-380562/1/../bin/lava-test-case <8>[ 9.766658] /lava-380562/1/../bin/lava-test-case <8>[ 9.783886] /lava-380562/1/../bin/lava-test-case <8>[ 9.801146] /lava-380562/1/../bin/lava-test-case <8>[ 9.817995] /lava-380562/1/../bin/lava-test-case <8>[ 9.835138] /lava-380562/1/../bin/lava-test-case <8>[ 9.852156] /lava-380562/1/../bin/lava-test-case <8>[ 9.866974] /lava-380562/1/../bin/lava-test-case <8>[ 9.884546] /lava-380562/1/../bin/lava-test-case <8>[ 9.902396] /lava-380562/1/../bin/lava-test-case <8>[ 9.917702] /lava-380562/1/../bin/lava-test-case <8>[ 9.935733] /lava-380562/1/../bin/lava-test-case <8>[ 9.950885] /lava-380562/1/../bin/lava-test-case <8>[ 9.969019] /lava-380562/1/../bin/lava-test-case <8>[ 10.985877] /lava-380562/1/../bin/lava-test-case <8>[ 12.004615] /lava-380562/1/../bin/lava-test-case <8>[ 13.021854] /lava-380562/1/../bin/lava-test-case <8>[ 14.040854] /lava-380562/1/../bin/lava-test-case <8>[ 14.056759] /lava-380562/1/../bin/lava-test-case <8>[ 14.074555] /lava-380562/1/../bin/lava-test-case <8>[ 14.089762] /lava-380562/1/../bin/lava-test-case <8>[ 14.107545] /lava-380562/1/../bin/lava-test-case <8>[ 14.122563] /lava-380562/1/../bin/lava-test-case <8>[ 14.140404] /lava-380562/1/../bin/lava-test-case <8>[ 14.155439] /lava-380562/1/../bin/lava-test-case <8>[ 14.173286] /lava-380562/1/../bin/lava-test-case <8>[ 14.190582] /lava-380562/1/../bin/lava-test-case <8>[ 14.205646] /lava-380562/1/../bin/lava-test-case <8>[ 14.223439] /lava-380562/1/../bin/lava-test-case <8>[ 14.240744] /lava-380562/1/../bin/lava-test-case <8>[ 14.257861] /lava-380562/1/../bin/lava-test-case <8>[ 14.275234] /lava-380562/1/../bin/lava-test-case <8>[ 14.290489] /lava-380562/1/../bin/lava-test-case <8>[ 14.308375] /lava-380562/1/../bin/lava-test-case <8>[ 14.323412] /lava-380562/1/../bin/lava-test-case <8>[ 14.340546] /lava-380562/1/../bin/lava-test-case <8>[ 14.354929] /lava-380562/1/../bin/lava-test-case <8>[ 14.372001] /lava-380562/1/../bin/lava-test-case <8>[ 14.388931] /lava-380562/1/../bin/lava-test-case <8>[ 14.403768] /lava-380562/1/../bin/lava-test-case <8>[ 14.421234] /lava-380562/1/../bin/lava-test-case <8>[ 15.437975] /lava-380562/1/../bin/lava-test-case <8>[ 16.456393] + set +x <8>[ 16.467508] / #