[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot : 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12243974/tftp-deploy-8jn8h4fq/kernel/zImage tftp 0x10000000 12243974/tftp-deploy-8jn8h4fq/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12243974/tftp-deploy-8jn8h4fq/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 6.2 MiB/s done Bytes transferred = 9708032 (942200 hex) => tftp 0x14000000 12243974/tftp-deploy-8jn8h4fq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12243974/tftp-deploy-8jn8h4fq/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12243974/tftp-deploy-8jn8h4fq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 14.2 MiB/s done Bytes transferred = 12154462 (b9765e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12243974/tftp-deploy-8jn8h4fq/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12243974/tftp-deploy-8jn8h4fq/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12243974/tftp-deploy-8jn8h4fq/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.5 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12243974/extract-nfsrootfs-ec0hjz0r,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12243974/extract-nfsrootfs-ec0hjz0r,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x942200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12154398 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41 (KernelCI@build-j43659-arm-gcc-10-multi-v7-defconfig-xlf8j) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Dec 11 09:24:04 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12243974/extract-nfsrootfs-ec0hjz0r,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936484K/1048576K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 46556K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022212] Console: colour dummy device 80x30 <6>[ 0.024104] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034511] CPU: Testing write buffer coherency: ok <6>[ 0.039644] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044942] pid_max: default: 32768 minimum: 301 <6>[ 0.049971] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057407] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066282] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072014] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079712] rcu: Hierarchical SRCU implementation. <6>[ 0.086671] EFI services will not be available. <6>[ 0.088908] smp: Bringing up secondary CPUs ... <6>[ 0.094200] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094208] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105546] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105554] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116746] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116754] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127191] smp: Brought up 1 node, 4 CPUs <6>[ 0.131415] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137872] CPU: All CPU(s) started in SVC mode. <6>[ 0.143294] devtmpfs: initialized <6>[ 0.153652] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158995] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168865] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179078] pinctrl core: initialized pinctrl subsystem <6>[ 0.183564] DMI not present or invalid. <6>[ 0.186664] NET: Registered protocol family 16 <6>[ 0.193963] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200590] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200770] cpuidle: using governor menu <6>[ 0.208896] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.395789] vdd1p1: supplied by regulator-dummy <6>[ 0.405219] vdd3p0: supplied by regulator-dummy <6>[ 0.414591] vdd2p5: supplied by regulator-dummy <6>[ 0.423987] vddarm: supplied by regulator-dummy <6>[ 0.433524] vddpu: supplied by regulator-dummy <6>[ 0.442665] vddsoc: supplied by regulator-dummy <6>[ 0.783901] No ATAGs? <6>[ 0.784091] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.791865] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.802107] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.812449] Serial: AMBA PL011 UART driver <6>[ 0.816675] printk: console [ramoops-1] enabled <6>[ 0.818950] pstore: Registered ramoops as persistent store backend <6>[ 0.825178] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.862923] iommu: Default domain type: Translated <6>[ 0.865830] vgaarb: loaded <5>[ 0.869058] SCSI subsystem initialized <6>[ 0.872692] usbcore: registered new interface driver usbfs <6>[ 0.877988] usbcore: registered new interface driver hub <6>[ 0.883517] usbcore: registered new device driver usb <6>[ 0.890390] i2c i2c-0: IMX I2C adapter registered <6>[ 0.895079] i2c i2c-1: IMX I2C adapter registered <6>[ 0.899550] i2c i2c-2: IMX I2C adapter registered <6>[ 0.905032] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.908908] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.918322] PTP clock support registered <6>[ 0.926210] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.077604] NET: Registered protocol family 2 <6>[ 2.079817] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.088227] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.095681] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.103757] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.111201] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.117900] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.124573] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.132053] NET: Registered protocol family 1 <6>[ 2.137113] RPC: Registered named UNIX socket transport module. <6>[ 2.142627] RPC: Registered udp transport module. <6>[ 2.147625] RPC: Registered tcp transport module. <6>[ 2.152544] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.159271] PCI: CLS 0 bytes, default 64 <6>[ 2.163934] Trying to unpack rootfs image as initramfs... <6>[ 3.118458] Freeing initrd memory: 11872K <4>[ 3.120388] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.127740] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.137502] Initialise system trusted keyrings <6>[ 3.140700] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.152866] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.156878] NFS: Registering the id_resolver key type <5>[ 3.161464] Key type id_resolver registered <5>[ 3.165855] Key type id_legacy registered <6>[ 3.170240] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.177101] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.184762] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.189846] Key type asymmetric registered <5>[ 3.193699] Asymmetric key parser 'x509' registered <6>[ 3.198902] bounce: pool size: 64 pages <6>[ 3.202950] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.210598] io scheduler mq-deadline registered <6>[ 3.215359] io scheduler kyber registered <6>[ 3.259872] mxs-dma 110000.dma-controller: initialized <4>[ 3.267275] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.275054] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.347527] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.355769] SuperH (H)SCI(F) driver initialized <6>[ 3.358807] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.367609] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.375489] printk: console [ttymxc1] enabled <6>[ 3.375489] printk: console [ttymxc1] enabled <6>[ 3.384696] printk: bootconsole [ec_imx21] disabled <6>[ 3.384696] printk: bootconsole [ec_imx21] disabled <6>[ 3.396430] msm_serial: driver initialized <6>[ 3.402396] STMicroelectronics ASC driver initialized <6>[ 3.409726] STM32 USART driver initialized <4>[ 3.424678] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.432597] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.439368] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.455999] brd: module loaded <6>[ 3.466784] loop: module loaded <6>[ 3.474158] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.482380] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.490669] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.499127] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.507139] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.514894] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.522461] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.533049] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.540345] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.549422] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.560231] scsi host0: ahci-imx <6>[ 3.564093] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.584929] CAN device driver interface <6>[ 3.590432] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.599963] pps pps0: new PPS source ptp0 <6>[ 3.622122] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.629759] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.634995] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.641265] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.646949] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.659095] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.666826] usbcore: registered new interface driver pegasus <6>[ 3.672793] usbcore: registered new interface driver asix <6>[ 3.678510] usbcore: registered new interface driver ax88179_178a <6>[ 3.684900] usbcore: registered new interface driver cdc_ether <6>[ 3.691080] usbcore: registered new interface driver smsc75xx <6>[ 3.697156] usbcore: registered new interface driver smsc95xx <6>[ 3.703202] usbcore: registered new interface driver net1080 <6>[ 3.709180] usbcore: registered new interface driver cdc_subset <6>[ 3.715395] usbcore: registered new interface driver zaurus <6>[ 3.721320] usbcore: registered new interface driver cdc_ncm <6>[ 3.730906] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.737729] ehci-pci: EHCI PCI platform driver <6>[ 3.742479] ehci-platform: EHCI generic platform driver <6>[ 3.748295] ehci-orion: EHCI orion driver <6>[ 3.752799] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.757291] ehci-st: EHCI STMicroelectronics driver <6>[ 3.762626] ehci-exynos: EHCI Exynos driver <6>[ 3.767293] ehci-atmel: EHCI Atmel driver <6>[ 3.771757] tegra-ehci: Tegra EHCI driver <6>[ 3.776279] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.782743] ohci-pci: OHCI PCI platform driver <6>[ 3.787513] ohci-platform: OHCI generic platform driver <6>[ 3.793267] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.797764] ohci-st: OHCI STMicroelectronics driver <6>[ 3.803101] ohci-atmel: OHCI Atmel driver <6>[ 3.808687] usbcore: registered new interface driver usb-storage <6>[ 3.823423] i2c /dev entries driver <6>[ 3.847513] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.853965] sdhci: Copyright(c) Pierre Ossman <6>[ 3.861439] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.869759] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.877593] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.881310] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.882882] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.893556] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.900973] usbcore: registered new interface driver usbhid <6>[ 3.906837] usbhid: USB HID core driver <6>[ 3.910051] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.916669] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.917724] NET: Registered protocol family 10 <6>[ 3.923210] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.925210] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.928902] Segment Routing with IPv6 <6>[ 3.940725] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.942577] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.960346] NET: Registered protocol family 17 <6>[ 3.965071] can: controller area network core <6>[ 3.969797] NET: Registered protocol family 29 <6>[ 3.974511] can: raw protocol <6>[ 3.977768] can: broadcast manager protocol <6>[ 3.981560] mmc2: new high speed SDHC card at address 0001 <6>[ 3.982228] can: netlink gateway - max_hops=1 <6>[ 3.988875] mmcblk2: mmc2:0001 SD 14.6 GiB <5>[ 3.993077] Key type dns_resolver registered <6>[ 4.003818] ThumbEE CPU extension supported. <5>[ 4.008452] Registering SWP/SWPB emulation handler <5>[ 4.013842] Loading compiled-in X.509 certificates <6>[ 4.024210] pstore: Using crash dump compression: deflate <4>[ 4.024583] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.037640] GPT:29296874 != 30560255 <4>[ 4.041486] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.047793] GPT:29296874 != 30560255 <4>[ 4.051541] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.051644] GPT: Use GNU Parted to correct GPT errors. <4>[ 4.059547] panel-simple panel-lcd: Specify missing connector_type <6>[ 4.064856] mmcblk2: p1 p2 p3 <4>[ 4.072753] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.091184] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.101094] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.106287] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.136240] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.142628] hub 1-0:1.0: USB hub found <6>[ 4.146737] hub 1-0:1.0: 1 port detected <6>[ 4.153349] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.169363] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.177270] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.185147] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.197355] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.205222] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.213082] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.223164] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.235311] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.243227] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.251242] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.264984] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.476309] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.677953] hub 1-1:1.0: USB hub found <6>[ 4.682187] hub 1-1:1.0: 3 ports detected <4>[ 4.692800] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.700763] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.709047] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.436713] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.456311] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.486372] Sending DHCP requests ., OK <6>[ 7.530440] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 7.538798] IP-Config: Complete: <6>[ 7.542320] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.553072] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 7.561218] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.561230] nameserver0=192.168.201.1 <6>[ 7.580068] Freeing unused kernel memory: 2048K <6>[ 7.607191] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.483520] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.495921] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.506516] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.514572] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.532077] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.540849] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.549464] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.558110] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.566705] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.581079] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.589052] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.597676] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.642413] caam 2100000.crypto: Entropy delay = 3200 <4>[ 8.645807] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.655711] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.664214] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.708597] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.740653] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.744385] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.750277] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.754008] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.769342] caam 2100000.crypto: Instantiated RNG4 SH1 <4>[ 8.770203] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.775435] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <4>[ 8.783490] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.790247] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.812194] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.819430] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.826985] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.833813] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.840936] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.848566] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.854977] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.862525] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.884172] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.892816] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.901395] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.910109] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.935484] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.943487] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.952333] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.966558] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.975105] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.983694] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.992267] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.211215] caam algorithms registered in /proc/crypto <6>[ 9.218197] caam 2100000.crypto: registering rng-caam <4>[ 9.229336] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.237287] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.254288] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.265750] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.274290] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers <6>[ 9.282827] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) ... <6>[ 9.294101] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 9.405973] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.117965] systemd[1]: System time before build time, advancing clock. <30>[ 10.161056] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.185603] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.228380] systemd[1]: Set hostname to . <30>[ 10.903367] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 10.912711] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 10.925548] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 10.935073] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 10.977633] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.017587] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.057323] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.097015] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.136616] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.176889] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.189680] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.227167] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.256696] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.296628] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.326792] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.357514] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.430624] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.440402] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.477909] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.518459] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.559448] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.598017] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.637505] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.647175] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.659662] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 11.700609] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.740598] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 11.781698] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 11.819404] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 11.862898] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 11.898859] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 11.911892] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 11.953608] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 11.990102] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.029499] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.071472] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.106911] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.147325] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.212731] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 12.513015] systemd-journald[277]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.201-cip41 #1 SMP Mon Dec 11 09:24:04 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12243974/extract-nfsrootfs-ec0hjz0r' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12243974/extract-nfsrootfs-ec0hjz0r' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12243974/environment . /lava-12243974/environment / # /lava-12243974/bin/lava-test-runner /lava-12243974/0 /lava-12243974/bin/lava-test-runner /lava-12243974/0 + export TESTRUN_ID=0_dmesg + cd /lava-12243974/0/tests/0_dmesg + cat uuid + UUID=12243974_1.6.2.4.1<8>[ 26.179200] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 26.254129] <8>[ 26.315740] <8>[ 26.378641] + set<8>[ 26.388263] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12243974/environment / # . /lava-12243974/environment/lava-12243974/bin/lava-test-runner /lava-12243974/1 / # /lava-12243974/bin/lava-test-runner /lava-12243974/1 + export TESTRUN_ID=1_bootrr + cd /lava-12243974/1/tests/1_bootrr + cat uuid + UUID=12243974_1.6.2.4.5<8>[ 26.926546] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12243974/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 disp0 backlight-lcd /lava-12243974/1/../bin/lava-test-case <8>[ 28.032689] /lava-12243974/1/../bin/lava-test-case <8>[ 28.091008] /lava-12243974/1/../bin/lava-test-case <8>[ 28.123663] + set +x<8>[ 28.148908] / #