Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2020.10 (Apr 28 2023 - 11:09:01 +0100) Trying to boot from MMC2 U-Boot 2020.10 (Apr 28 2023 - 11:09:01 +0100) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... Unable to use mmc 1:1... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2 0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.1.18 (1026 ms) => setenv serverip 192.168.1.1 setenv serverip 192.168.1.1 => tftp 0x82000000 1059399/tftp-deploy-tedcfcfa/kernel/zImage tftp 0x82000000 1059399/tftp-deploy-tedcfcfa/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.18 Filename '1059399/tftp-deploy-tedcfcfa/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 3.9 MiB/s done Bytes transferred = 4609432 (465598 hex) => tftp 0x83000000 1059399/tftp-deploy-tedcfcfa/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1059399/tftp-deploy-tedcfcfa/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.18 Filename '1059399/tftp-deploy-tedcfcfa/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 3.9 MiB/s done Bytes transferred = 14164248 (d82118 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1059399/tftp-deploy-tedcfcfa/dtb/am335x-boneblack.dtb tftp 0x88000000 1059399/tftp-deploy-tedcfcfa/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.18 Filename '1059399/tftp-deploy-tedcfcfa/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-12-14 15:48:41 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14164184 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41 (KernelCI@build-j48188-arm-gcc-10-omap2plus-defconfig-4flnm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Dec 14 14:50:14 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472032K/522240K available (9216K kernel code, 1027K rwdata, 2180K rodata, 1024K init, 278K bss, 33824K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008344] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018564] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030200] Console: colour dummy device 80x30 <3>[ 0.035070] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042129] This ensures that you still see kernel messages. Please <3>[ 0.048856] update your kernel commandline. <6>[ 0.053461] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095545] CPU: Testing write buffer coherency: ok <6>[ 0.100926] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106391] pid_max: default: 32768 minimum: 301 <6>[ 0.111552] LSM: Security Framework initializing <6>[ 0.116650] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124464] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134125] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140642] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147844] rcu: Hierarchical SRCU implementation. <6>[ 0.153636] smp: Bringing up secondary CPUs ... <6>[ 0.158574] smp: Brought up 1 node, 1 CPU <6>[ 0.163001] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169731] CPU: All CPU(s) started in SVC mode. <6>[ 0.175456] devtmpfs: initialized <6>[ 0.191263] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199803] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210240] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218883] pinctrl core: initialized pinctrl subsystem <6>[ 0.226448] NET: Registered protocol family 16 <6>[ 0.234107] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260572] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266667] audit: initializing netlink subsys (disabled) <6>[ 0.273736] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273751] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280362] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287082] cpuidle: using governor menu <5>[ 1.168568] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.294060] No ATAGs? <6>[ 1.296686] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.321266] Kprobes globally optimized <6>[ 1.334417] iommu: Default domain type: Translated <6>[ 1.341807] vgaarb: loaded <5>[ 1.345404] SCSI subsystem initialized <6>[ 1.350584] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.355969] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.365768] PTP clock support registered <6>[ 1.371377] clocksource: Switched to clocksource dmtimer <5>[ 2.009020] VFS: Disk quotas dquot_6.6.0 <6>[ 2.013526] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.030391] NET: Registered protocol family 2 <6>[ 2.035570] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.044243] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.053209] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.061505] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.069164] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.076105] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.083137] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.090743] NET: Registered protocol family 1 <6>[ 2.096544] RPC: Registered named UNIX socket transport module. <6>[ 2.103006] RPC: Registered udp transport module. <6>[ 2.108113] RPC: Registered tcp transport module. <6>[ 2.113239] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.120145] PCI: CLS 0 bytes, default 64 <6>[ 2.125222] Trying to unpack rootfs image as initramfs... <6>[ 3.112848] Freeing initrd memory: 13836K <6>[ 3.118680] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.129155] Initialise system trusted keyrings <6>[ 3.134532] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.142754] NFS: Registering the id_resolver key type <5>[ 3.148279] Key type id_resolver registered <5>[ 3.152927] Key type id_legacy registered <6>[ 3.157375] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.165441] Key type asymmetric registered <5>[ 3.169934] Asymmetric key parser 'x509' registered <6>[ 3.175280] io scheduler mq-deadline registered <6>[ 3.180211] io scheduler kyber registered <3>[ 3.318709] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.327416] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.436557] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.478766] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.550740] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.559457] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.619534] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.628238] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.645756] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.654439] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.718126] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.726694] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.753700] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.768183] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.779154] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.788583] printk: console [ttyS0] enabled <6>[ 3.788583] printk: console [ttyS0] enabled <6>[ 3.797651] printk: bootconsole [omap8250] disabled <6>[ 3.797651] printk: bootconsole [omap8250] disabled <6>[ 3.821501] brd: module loaded <6>[ 3.832282] loop: module loaded <3>[ 3.837741] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.911362] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.954010] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.963920] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.970573] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.976404] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.983955] cpsw 4a100000.ethernet: Detected MACID = f4:b8:98:ab:fa:84 <6>[ 3.993004] i2c /dev entries driver <5>[ 3.998514] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.006450] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.012997] sdhci: Copyright(c) Pierre Ossman <6>[ 4.018357] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.026665] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.036467] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.044927] Initializing XFRM netlink socket <6>[ 4.049727] NET: Registered protocol family 10 <6>[ 4.056169] Segment Routing with IPv6 <6>[ 4.060215] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.067282] NET: Registered protocol family 17 <6>[ 4.072131] NET: Registered protocol family 15 <5>[ 4.076988] Key type dns_resolver registered <6>[ 4.082180] oprofile: using arm/armv7 <6>[ 4.086224] ThumbEE CPU extension supported. <5>[ 4.090798] Registering SWP/SWPB emulation handler <3>[ 4.096355] omap_voltage_late_init: Voltage driver support not added <3>[ 4.103069] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.111481] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.120153] SmartReflex Class3 initialized <6>[ 4.125276] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.134248] Loading compiled-in X.509 certificates <6>[ 4.159337] OMAP GPIO hardware version 0.1 <4>[ 4.192031] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.205648] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.214145] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.220487] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.230517] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.241923] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.250934] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.256158] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.270683] mmc1: new high speed MMC card at address 0001 <6>[ 4.277539] mmcblk1: mmc1:0001 MK2704 3.53 GiB <6>[ 4.283097] mmcblk1boot0: mmc1:0001 MK2704 partition 1 2.00 MiB <6>[ 4.289767] mmcblk1boot1: mmc1:0001 MK2704 partition 2 2.00 MiB <6>[ 4.296375] mmcblk1rpmb: mmc1:0001 MK2704 partition 3 512 KiB, chardev (249:0) <6>[ 4.305900] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.314877] mmcblk1: p1 <6>[ 4.323181] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.412876] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.562011] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.581359] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.611446] Sending DHCP requests ., OK <6>[ 7.655439] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.18 <6>[ 7.663430] IP-Config: Complete: <6>[ 7.666941] device=eth0, hwaddr=f4:b8:98:ab:fa:84, ipaddr=192.168.1.18, mask=255.255.255.0, gw=192.168.1.1 <6>[ 7.677353] host=192.168.1.18, domain=example.org, nis-domain=(none) <6>[ 7.684469] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.684477] nameserver0=192.168.1.1 <6>[ 7.697854] Freeing unused kernel memory: 1024K <6>[ 7.721800] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.953304] udevd[100]: starting version 3.2.9 <5>[ 7.959632] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.967729] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.974849] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.991745] udevd[100]: specified user 'tss' unknown <27>[ 7.997316] udevd[100]: specified group 'tss' unknown <30>[ 8.013687] udevd[101]: starting eudev-3.2.9 <6>[ 8.848780] remoteproc remoteproc0: wkup_m3 is available <4>[ 8.948388] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.957590] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.031710] usbcore: registered new interface driver usbfs <6>[ 9.037569] usbcore: registered new interface driver hub <6>[ 9.043355] usbcore: registered new device driver usb <4>[ 9.282705] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.291834] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.483922] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.489580] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.684924] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.693650] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.701170] usb usb1: Product: MUSB HDRC host driver <6>[ 9.706460] usb usb1: Manufacturer: Linux 5.10.201-cip41 musb-hcd <6>[ 9.712862] usb usb1: SerialNumber: musb-hdrc.1 <4>[ 9.838499] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 9.880971] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 9.944266] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 10.012855] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 10.020444] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 10.029326] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 10.132051] hub 1-0:1.0: USB hub found <6>[ 10.142406] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.147819] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <6>[ 10.193252] hub 1-0:1.0: 1 port detected <4>[ 10.200073] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 10.303213] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 10.403448] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 10.443924] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 10.521475] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.614267] tda998x 0-0070: found TDA19988 <3>[ 10.739939] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 10.973378] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 10.984861] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 11.214537] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 11.316953] remoteproc remoteproc0: powering up wkup_m3 <4>[ 11.371649] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.381554] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.387768] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 11.805688] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 11.858065] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 11.892418] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 11.909835] random: crng init done <6>[ 11.941893] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 11.951068] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 12.165809] PM: Cannot get wkup_m3_ipc handle <6>[ 12.478465] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.494788] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.554234] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 12.565464] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.623014] PM: Cannot get wkup_m3_ipc handle <3>[ 12.650647] PM: Cannot get wkup_m3_ipc handle <3>[ 13.080227] PM: Cannot get wkup_m3_ipc handle <3>[ 13.112477] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1059399/environment . /lava-1059399/environment / # /lava-1059399/bin/lava-test-runner /lava-1059399/0 /lava-1059399/bin/lava-test-runner /lava-1059399/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1059399/0/tests/0_dmesg + cat uuid + UUID=1059399_1.5.2.4.1 <8>[ 14.036069] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.102149] <8>[ 14.162375] <8>[ 14.222533] + set +x <8>[ 14.234021] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1059399/environment / # . /lava-1059399/environment/lava-1059399/bin/lava-test-runner /lava-1059399/1 / # /lava-1059399/bin/lava-test-runner /lava-1059399/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1059399/1/tests/1_bootrr + cat uuid + UUID=1059399_1.5.2.4.5 <8>[ 14.773039] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1059399/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-1059399/1/../bin/lava-test-case <8>[ 15.879596] /lava-1059399/1/../bin/lava-test-case <8>[ 15.935169] /lava-1059399/1/../bin/lava-test-case <8>[ 15.967748] /lava-1059399/1/../bin/lava-test-case <8>[ 16.029468] /lava-1059399/1/../bin/lava-test-case <8>[ 16.080422] /lava-1059399/1/../bin/lava-test-case <8>[ 16.120866] /lava-1059399/1/../bin/lava-test-case <8>[ 16.172254] /lava-1059399/1/../bin/lava-test-case <8>[ 16.238160] /lava-1059399/1/../bin/lava-test-case <8>[ 16.278999] /lava-1059399/1/../bin/lava-test-case <8>[ 16.329633] /lava-1059399/1/../bin/lava-test-case <8>[ 16.370357] /lava-1059399/1/../bin/lava-test-case <8>[ 16.420984] /lava-1059399/1/../bin/lava-test-case <8>[ 16.461802] /lava-1059399/1/../bin/lava-test-case <8>[ 16.502047] /lava-1059399/1/../bin/lava-test-case <8>[ 16.542556] /lava-1059399/1/../bin/lava-test-case <8>[ 16.592487] /lava-1059399/1/../bin/lava-test-case <8>[ 16.634030] /lava-1059399/1/../bin/lava-test-case <8>[ 16.685006] /lava-1059399/1/../bin/lava-test-case <8>[ 16.734838] /lava-1059399/1/../bin/lava-test-case <8>[ 16.775174] /lava-1059399/1/../bin/lava-test-case <8>[ 16.825972] /lava-1059399/1/../bin/lava-test-case <8>[ 16.876404] /lava-1059399/1/../bin/lava-test-case <8>[ 16.917847] /lava-1059399/1/../bin/lava-test-case <8>[ 16.969269] /lava-1059399/1/../bin/lava-test-case <8>[ 17.010594] /lava-1059399/1/../bin/lava-test-case <8>[ 17.061010] /lava-1059399/1/../bin/lava-test-case <8>[ 17.102117] /lava-1059399/1/../bin/lava-test-case <8>[ 18.175804] /lava-1059399/1/../bin/lava-test-case <8>[ 18.217233] /lava-1059399/1/../bin/lava-test-case <8>[ 18.268121] /lava-1059399/1/../bin/lava-test-case <8>[ 18.309710] /lava-1059399/1/../bin/lava-test-case <8>[ 18.360345] /lava-1059399/1/../bin/lava-test-case <8>[ 18.401025] /lava-1059399/1/../bin/lava-test-case <8>[ 18.451952] /lava-1059399/1/../bin/lava-test-case <8>[ 18.492264] /lava-1059399/1/../bin/lava-test-case <8>[ 18.542942] /lava-1059399/1/../bin/lava-test-case <8>[ 18.583362] /lava-1059399/1/../bin/lava-test-case <8>[ 18.634037] /lava-1059399/1/../bin/lava-test-case <8>[ 18.674287] /lava-1059399/1/../bin/lava-test-case <8>[ 18.724847] /lava-1059399/1/../bin/lava-test-case <8>[ 18.765348] /lava-1059399/1/../bin/lava-test-case <8>[ 18.815978] /lava-1059399/1/../bin/lava-test-case <8>[ 18.856560] /lava-1059399/1/../bin/lava-test-case <8>[ 18.906794] /lava-1059399/1/../bin/lava-test-case <8>[ 18.947100] /lava-1059399/1/../bin/lava-test-case <8>[ 18.997348] /lava-1059399/1/../bin/lava-test-case <8>[ 19.038641] /lava-1059399/1/../bin/lava-test-case <8>[ 19.089182] /lava-1059399/1/../bin/lava-test-case <8>[ 19.130431] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1059399/1/../bin/lava-test-case <8>[ 19.173570] /lava-1059399/1/../bin/lava-test-case <8>[ 19.224381] /lava-1059399/1/../bin/lava-test-case <8>[ 19.272456] + set +x <8>[ 19.289097] / #