Trying 192.168.56.4... Connected to moya. Escape character is '^]'. ser2net port telnet,3000 device serialdev, /dev/serial/by-path/pci-0000:00:14.0-usb-0:3.4:1.0-port0, 115200n81, local=false [,115200N81] (Debian GNU/Linux) U-Boot SPL 2023.07.02-dh-stm32mp1-dhcor-avenger96-20230727.02 (Jul 11 2023 - 15:20:44 +0000) Model: Arrow Electronics STM32MP15xx Avenger96 board Code: SoM:rev=0,ddr3=3 Board:rev=1 RAM: DDR3L 32bits 2x4Gb 533MHz WDT: Started watchdog@5a002000 with servicing every 1000ms (32s timeout) Trying to boot from MMC1 image entry point: 0xc0100000 U-Boot 2023.07.02-dh-stm32mp1-dhcor-avenger96-20230727.02 (Jul 11 2023 - 15:20:44 +0000) CPU: STM32MP157AAC Rev.B Model: Arrow Electronics STM32MP15xx Avenger96 board Board: stm32mp1 in basic mode (arrow,stm32mp15xx-avenger96) DRAM: 1 GiB Clocks: - MPU : 650 MHz - MCU : 208.878 MHz - AXI : 266.500 MHz - PER : 24 MHz - DDR : 533 MHz Core: 285 devices, 34 uclasses, devicetree: separate WDT: Started watchdog@5a002000 with servicing every 1000ms (32s timeout) MMC: STM32 SD/MMC: 2, STM32 SD/MMC: 0, STM32 SD/MMC: 1 Loading Environment from SPIFlash... SF: Detected w25q16dw with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: eth0: ethernet@5800a000 Hit any key to stop autoboot: 3  0 STM32MP> setenv autoload no setenv autoload no STM32MP> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff STM32MP> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff STM32MP> dhcp dhcp ethernet@5800a000 Waiting for PHY auto negotiation to complete.......... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 *** Unhandled DHCP Option in OFFER/ACK: 42 *** Unhandled DHCP Option in OFFER/ACK: 42 DHCP client bound to address 192.168.56.204 (7843 ms) STM32MP> setenv serverip 192.168.56.39 setenv serverip 192.168.56.39 STM32MP> tftp 0xc2000000 579654/tftp-deploy-4n9ymr2i/kernel/uImage tftp 0xc2000000 579654/tftp-deploy-4n9ymr2i/kernel/uImage Using ethernet@5800a000 device TFTP from server 192.168.56.39; our IP address is 192.168.56.204 Filename '579654/tftp-deploy-4n9ymr2i/kernel/uImage'. Load address: 0xc2000000 Loading: *################################################## 9.3 MiB 17.5 MiB/s done Bytes transferred = 9716288 (944240 hex) STM32MP> tftp 0xc4400000 579654/tftp-deploy-4n9ymr2i/ramdisk/ramdisk.cpio.gz.uboot tftp 0xc4400000 579654/tftp-deploy-4n9ymr2i/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@5800a000 device TFTP from server 192.168.56.39; our IP address is 192.168.56.204 Filename '579654/tftp-deploy-4n9ymr2i/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0xc4400000 Loading: *################################################## 15.3 MiB 15.3 MiB/s done Bytes transferred = 16080610 (f55ee2 hex) STM32MP> setenv initrd_size ${filesize} setenv initrd_size ${filesize} STM32MP> tftp 0xc4000000 579654/tftp-deploy-4n9ymr2i/dtb/stm32mp157a-dhcor-avenger96.dtb tftp 0xc4000000 579654/tftp-deploy-4n9ymr2i/dtb/stm32mp157a-dhcor-avenger96.dtb Using ethernet@5800a000 device TFTP from server 192.168.56.39; our IP address is 192.168.56.204 Filename '579654/tftp-deploy-4n9ymr2i/dtb/stm32mp157a-dhcor-avenger96.dtb'. Load address: 0xc4000000 Loading: *################################################## 56.3 KiB 11 MiB/s done Bytes transferred = 57690 (e15a hex) STM32MP> setenv bootargs 'console=ttySTM0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttySTM0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' STM32MP> bootm 0xc2000000 0xc4400000 0xc4000000 bootm 0xc2000000 0xc4400000 0xc4000000 ## Booting kernel from Legacy Image at c2000000 ... Image Name: Created: 2024-02-13 19:04:00 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 9716224 Bytes = 9.3 MiB Load Address: c2000000 Entry Point: c2000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at c4400000 ... Image Name: Created: 2024-02-13 19:04:02 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16080546 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at c4000000 Booting using the fdt blob at 0xc4000000 Working FDT set to c4000000 Loading Kernel Image Using Device Tree in place at c4000000, end c4011159 Working FDT set to c4000000 Starting kernel ... <6>[ 0.000000] Booting Linux on physical CPU 0x0 <5>[ 0.000000] Linux version 5.10.209-cip44 (KernelCI@build-j106860-arm-gcc-10-multi-v7-defconfig-6hp2s) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Feb 13 17:16:56 UTC 2024 <6>[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d <6>[ 0.000000] CPU: div instructions available: patching division code <6>[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache <6>[ 0.000000] OF: fdt: Machine model: Arrow Electronics STM32MP157A Avenger96 board <4>[ 0.000000] Malformed early option 'earlycon' <6>[ 0.000000] Memory policy: Data cache writealloc <6>[ 0.000000] efi: UEFI not found. <6>[ 0.000000] cma: Reserved 64 MiB at 0xfb800000 <6>[ 0.000000] Zone ranges: <6>[ 0.000000] DMA [mem 0x00000000c0000000-0x00000000efffffff] <6>[ 0.000000] Normal empty <6>[ 0.000000] HighMem [mem 0x00000000f0000000-0x00000000ffffefff] <6>[ 0.000000] Movable zone start for each node <6>[ 0.000000] Early memory node ranges <6>[ 0.000000] node 0: [mem 0x00000000c0000000-0x00000000ffffefff] <6>[ 0.000000] Initmem setup node 0 [mem 0x00000000c0000000-0x00000000ffffefff] <6>[ 0.000000] psci: probing for conduit method from DT. <6>[ 0.000000] psci: PSCIv1.0 detected in firmware. <6>[ 0.000000] psci: Using standard PSCI v0.2 function IDs <6>[ 0.000000] psci: Trusted OS migration not required <6>[ 0.000000] psci: SMC Calling Convention v1.0 <6>[ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260607 <5>[ 0.000000] Kernel command line: console=ttySTM0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932716K/1048572K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 50320K reserved, 65536K cma-reserved, 196604K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000010] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.000030] Switching to timer-based delay loop, resolution 41ns <6>[ 0.012207] Console: colour dummy device 80x30 <6>[ 0.012286] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.012313] CPU: Testing write buffer coherency: ok <6>[ 0.012396] pid_max: default: 32768 minimum: 301 <6>[ 0.012608] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.012637] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.013973] CPU0: update cpu_capacity 1024 <6>[ 0.014002] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.014968] Setting up static identity map for 0xc0300000 - 0xc03000ac <6>[ 0.018348] rcu: Hierarchical SRCU implementation. <6>[ 0.026056] EFI services will not be available. <6>[ 0.026484] smp: Bringing up secondary CPUs ... <6>[ 0.027392] CPU1: update cpu_capacity 1024 <6>[ 0.027403] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.027605] smp: Brought up 1 node, 2 CPUs <6>[ 0.027640] SMP: Total of 2 processors activated (96.00 BogoMIPS). <6>[ 0.027653] CPU: All CPU(s) started in SVC mode. <6>[ 0.028539] devtmpfs: initialized <6>[ 0.046733] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.047074] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.047110] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.050082] pinctrl core: initialized pinctrl subsystem <6>[ 0.053490] DMI not present or invalid. <6>[ 0.054776] NET: Registered protocol family 16 <6>[ 0.057490] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.062003] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.062368] cpuidle: using governor menu <6>[ 0.062641] No ATAGs? <6>[ 0.062785] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.062802] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.068208] Serial: AMBA PL011 UART driver <6>[ 0.115435] /soc/interrupt-controller@5000d000: bank0 <6>[ 0.115472] /soc/interrupt-controller@5000d000: bank1 <6>[ 0.115492] /soc/interrupt-controller@5000d000: bank2 <6>[ 0.121044] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOA bank added <6>[ 0.122509] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOB bank added <6>[ 0.123878] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOC bank added <6>[ 0.125343] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOD bank added <6>[ 0.126718] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOE bank added <6>[ 0.128091] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOF bank added <6>[ 0.129474] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOG bank added <6>[ 0.130860] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOH bank added <6>[ 0.132222] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOI bank added <6>[ 0.132386] stm32mp157-pinctrl soc:pin-controller@50002000: Pinctrl STM32 initialized <6>[ 0.134883] stm32mp157-pinctrl soc:pin-controller-z@54004000: GPIOZ bank added <6>[ 0.134922] stm32mp157-pinctrl soc:pin-controller-z@54004000: Pinctrl STM32 initialized <3>[ 0.160866] reg-fixed-voltage regulator-buck-io: Failed to register regulator: -517 <6>[ 0.164092] iommu: Default domain type: Translated <6>[ 0.164496] vgaarb: loaded <5>[ 0.165594] SCSI subsystem initialized <6>[ 0.166414] usbcore: registered new interface driver usbfs <6>[ 0.166500] usbcore: registered new interface driver hub <6>[ 0.166571] usbcore: registered new device driver usb <6>[ 0.168187] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.168210] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.168244] PTP clock support registered <6>[ 0.171975] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.533864] NET: Registered protocol family 2 <6>[ 1.534255] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.535936] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.535997] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.536110] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.536289] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.536448] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.536521] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.536786] NET: Registered protocol family 1 <6>[ 1.537910] RPC: Registered named UNIX socket transport module. <6>[ 1.537936] RPC: Registered udp transport module. <6>[ 1.537949] RPC: Registered tcp transport module. <6>[ 1.537961] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.537983] PCI: CLS 0 bytes, default 64 <6>[ 1.538595] Trying to unpack rootfs image as initramfs... <6>[ 3.200293] Freeing initrd memory: 15704K <6>[ 3.201143] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 3.202984] Initialise system trusted keyrings <6>[ 3.203446] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.212390] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.213537] NFS: Registering the id_resolver key type <5>[ 3.213662] Key type id_resolver registered <5>[ 3.213678] Key type id_legacy registered <6>[ 3.213842] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.213862] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.213917] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.214620] Key type asymmetric registered <5>[ 3.214645] Asymmetric key parser 'x509' registered <6>[ 3.214730] bounce: pool size: 64 pages <6>[ 3.214793] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.214810] io scheduler mq-deadline registered <6>[ 3.214823] io scheduler kyber registered <6>[ 3.315991] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.320736] SuperH (H)SCI(F) driver initialized <6>[ 3.321804] msm_serial: driver initialized <6>[ 3.322134] STMicroelectronics ASC driver initialized <6>[ 3.324215] STM32 USART driver initialized <6>[ 3.324892] stm32-usart 4000e000.serial: rx dma alloc failed <6>[ 3.324917] stm32-usart 4000e000.serial: interrupt mode used for rx (no dma) <6>[ 3.324934] stm32-usart 4000e000.serial: tx dma alloc failed <6>[ 3.324949] stm32-usart 4000e000.serial: interrupt mode used for tx (no dma) <6>[ 3.324985] 4000e000.serial: ttySTM2 at MMIO 0x4000e000 (irq = 30, base_baud = 4000000) is a stm32-usart <6>[ 3.325280] serial serial0: tty port ttySTM2 registered <6>[ 3.325980] stm32-usart 40010000.serial: rx dma alloc failed <6>[ 3.326004] stm32-usart 40010000.serial: interrupt mode used for rx (no dma) <6>[ 3.326020] stm32-usart 40010000.serial: tx dma alloc failed <6>[ 3.326035] stm32-usart 40010000.serial: interrupt mode used for tx (no dma) <6>[ 3.326064] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 31, base_baud = 4000000) is a stm32-usart <6>[ 4.245562] printk: console [ttySTM0] enabled <6>[ 4.251344] stm32-usart 40018000.serial: rx dma alloc failed <6>[ 4.256135] stm32-usart 40018000.serial: interrupt mode used for rx (no dma) <6>[ 4.263423] stm32-usart 40018000.serial: tx dma alloc failed <6>[ 4.269321] stm32-usart 40018000.serial: interrupt mode used for tx (no dma) <6>[ 4.276687] 40018000.serial: ttySTM1 at MMIO 0x40018000 (irq = 36, base_baud = 4000000) is a stm32-usart <5>[ 4.305232] random: crng init done <6>[ 4.320659] brd: module loaded <6>[ 4.331068] loop: module loaded <6>[ 4.348322] CAN device driver interface <6>[ 4.351906] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.358171] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.362177] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.368423] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.374016] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.383773] stm32-dwmac 5800a000.ethernet: IRQ eth_wake_irq not found <6>[ 4.389038] stm32-dwmac 5800a000.ethernet: IRQ eth_lpi not found <6>[ 4.395562] stm32-dwmac 5800a000.ethernet: PTP uses main clock <6>[ 4.401421] stm32-dwmac 5800a000.ethernet: no reset control found <6>[ 4.408409] stm32-dwmac 5800a000.ethernet: User ID: 0x40, Synopsys ID: 0x42 <6>[ 4.415121] stm32-dwmac 5800a000.ethernet: DWMAC4/5 <6>[ 4.420255] stm32-dwmac 5800a000.ethernet: DMA HW capability register supported <6>[ 4.427897] stm32-dwmac 5800a000.ethernet: RX Checksum Offload Engine supported <6>[ 4.435449] stm32-dwmac 5800a000.ethernet: TX Checksum insertion supported <6>[ 4.442595] stm32-dwmac 5800a000.ethernet: Wake-Up On Lan supported <6>[ 4.449251] stm32-dwmac 5800a000.ethernet: TSO supported <6>[ 4.454729] stm32-dwmac 5800a000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 4.462837] stm32-dwmac 5800a000.ethernet: Enabled Flow TC (entries=2) <6>[ 4.469607] stm32-dwmac 5800a000.ethernet: TSO feature enabled <6>[ 4.475734] stm32-dwmac 5800a000.ethernet: Using 32 bits DMA width <6>[ 4.534608] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.540910] usbcore: registered new interface driver pegasus <6>[ 4.546941] usbcore: registered new interface driver asix <6>[ 4.552537] usbcore: registered new interface driver ax88179_178a <6>[ 4.558838] usbcore: registered new interface driver cdc_ether <6>[ 4.565012] usbcore: registered new interface driver smsc75xx <6>[ 4.570971] usbcore: registered new interface driver smsc95xx <6>[ 4.577015] usbcore: registered new interface driver net1080 <6>[ 4.582939] usbcore: registered new interface driver cdc_subset <6>[ 4.589092] usbcore: registered new interface driver zaurus <6>[ 4.595018] usbcore: registered new interface driver cdc_ncm <6>[ 4.604439] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.609791] ehci-pci: EHCI PCI platform driver <6>[ 4.614641] ehci-platform: EHCI generic platform driver <6>[ 4.620551] ehci-orion: EHCI orion driver <6>[ 4.624546] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.628706] ehci-st: EHCI STMicroelectronics driver <6>[ 4.633914] ehci-exynos: EHCI Exynos driver <6>[ 4.638280] ehci-atmel: EHCI Atmel driver <6>[ 4.642580] tegra-ehci: Tegra EHCI driver <6>[ 4.646836] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.653218] ohci-pci: OHCI PCI platform driver <6>[ 4.657917] ohci-platform: OHCI generic platform driver <6>[ 4.663596] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.667785] ohci-st: OHCI STMicroelectronics driver <6>[ 4.672987] ohci-atmel: OHCI Atmel driver <6>[ 4.678029] usbcore: registered new interface driver usb-storage <3>[ 4.688791] stm32_rtc 5c004000.rtc: IRQ index 1 not found <4>[ 4.693067] stm32_rtc 5c004000.rtc: alarm can't wake up the system: -6 <6>[ 4.700718] stm32_rtc 5c004000.rtc: registered as rtc0 <6>[ 4.705342] stm32_rtc 5c004000.rtc: setting system clock to 2000-01-01T00:00:23 UTC (946684823) <4>[ 4.714591] stm32_rtc 5c004000.rtc: Date/Time must be initialized <6>[ 4.720561] stm32_rtc 5c004000.rtc: registered rev:1.2 <6>[ 4.727606] i2c /dev entries driver <6>[ 4.752672] stm32f7-i2c 40012000.i2c: STM32F7 I2C-0 bus adapter <6>[ 4.778407] stm32f7-i2c 40013000.i2c: STM32F7 I2C-1 bus adapter <6>[ 4.806551] stpmic1 2-0033: PMIC Chip Version: 0x10 <6>[ 4.818617] vddcore: supplied by regulator-dummy <6>[ 4.825736] vdd_ddr: supplied by regulator-dummy <6>[ 4.832646] vdd: supplied by regulator-dummy <6>[ 4.839143] v3v3: supplied by regulator-dummy <6>[ 4.845467] vdda: Bringing 1800000uV into 2900000-2900000uV <6>[ 4.850934] vdda: supplied by v3v3 <6>[ 4.856514] v2v8: Bringing 1800000uV into 2800000-2800000uV <6>[ 4.861974] v2v8: supplied by v3v3 <6>[ 4.866616] vtt_ddr: supplied by vdd_ddr <6>[ 4.872291] vdd_usb: supplied by regulator-dummy <6>[ 4.877016] vdd_sd: supplied by v3v3 <6>[ 4.883439] v1v8: Bringing 1000000uV into 1800000-1800000uV <6>[ 4.888760] v1v8: supplied by v3v3 <6>[ 4.892387] vref_ddr: supplied by regulator-dummy <6>[ 4.899800] bst_out: supplied by regulator-dummy <6>[ 4.905143] vbus_otg: supplied by bst_out <6>[ 4.909393] vbus_sw: supplied by bst_out <6>[ 4.918294] input: pmic_onkey as /devices/platform/soc/5c002000.i2c/i2c-2/2-0033/5c002000.i2c:stpmic@33:onkey/input/input0 <4>[ 4.930285] at24 2-0053: supply vcc not found, using dummy regulator <6>[ 4.936410] at24 2-0053: 256 byte 24c02 EEPROM, writable, 16 bytes/write <6>[ 4.942603] stm32f7-i2c 5c002000.i2c: STM32F7 I2C-2 bus adapter <6>[ 4.958008] stm_thermal 50028000.thermal: stm_thermal_probe: Driver initialized successfully <6>[ 4.974141] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.979142] sdhci: Copyright(c) Pierre Ossman <6>[ 4.985715] mmci-pl18x 48004000.sdmmc: mmc1: PL180 manf 53 rev1 at 0x48004000 irq 56,0 (pio) <6>[ 4.986945] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.994676] mmci-pl18x 58005000.sdmmc: Got CD GPIO <6>[ 5.001083] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.008730] mmci-pl18x 58005000.sdmmc: mmc0: PL180 manf 53 rev1 at 0x58005000 irq 61,0 (pio) <6>[ 5.019751] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.026561] usbcore: registered new interface driver usbhid <6>[ 5.031091] usbhid: USB HID core driver <6>[ 5.041098] NET: Registered protocol family 10 <6>[ 5.047385] Segment Routing with IPv6 <6>[ 5.049997] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.057048] NET: Registered protocol family 17 <6>[ 5.060793] can: controller area network core <6>[ 5.065552] NET: Registered protocol family 29 <6>[ 5.070111] can: raw protocol <6>[ 5.073383] can: broadcast manager protocol <6>[ 5.077803] can: netlink gateway - max_hops=1 <5>[ 5.083161] Key type dns_resolver registered <6>[ 5.087058] ThumbEE CPU extension supported. <5>[ 5.091465] Registering SWP/SWPB emulation handler <5>[ 5.097202] Loading compiled-in X.509 certificates <6>[ 5.115861] mmc0: new high speed SDXC card at address e624 <6>[ 5.121123] mmcblk0: mmc0:e624 SD64G 59.5 GiB <6>[ 5.129199] stm32-dma 48000000.dma-controller: STM32 DMA driver registered <6>[ 5.137057] stm32-dma 48001000.dma-controller: STM32 DMA driver registered <6>[ 5.146391] stm32-mdma 58000000.dma-controller: STM32 MDMA driver registered <6>[ 5.153170] buck-io: supplied by vdd <6>[ 5.156438] usb33: supplied by vdd_usb <6>[ 5.161626] reg11: supplied by buck-io <6>[ 5.164512] reg18: supplied by buck-io <6>[ 5.168971] stm32-usbphyc 5a006000.usbphyc: registered rev:1.0 <4>[ 5.183686] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 5.187832] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 5.189924] GPT:3204245 != 124735487 <6>[ 5.195820] spi-nor spi0.0: w25q16dw (2048 Kbytes) <4>[ 5.199506] GPT:Alternate GPT header not at the end of the disk. <4>[ 5.199511] GPT:3204245 != 124735487 <4>[ 5.199515] GPT: Use GNU Parted to correct GPT errors. <6>[ 5.199586] mmcblk0: p1 p2 p3 p4 <4>[ 5.206158] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) <4>[ 5.231851] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) <4>[ 5.240163] dwc2 49000000.usb-otg: supply vusb_d not found, using dummy regulator <4>[ 5.246755] dwc2 49000000.usb-otg: supply vusb_a not found, using dummy regulator <4>[ 5.257275] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 5.263937] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <6>[ 5.324721] mmc1: new high speed SDIO card at address 0001 <6>[ 5.389558] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM <6>[ 5.396560] dwc2 49000000.usb-otg: DWC OTG Controller <6>[ 5.401126] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 1 <6>[ 5.408878] dwc2 49000000.usb-otg: irq 57, io mem 0x49000000 <6>[ 5.415919] hub 1-0:1.0: USB hub found <6>[ 5.418783] hub 1-0:1.0: 1 port detected <6>[ 5.427009] ehci-platform 5800d000.usbh-ehci: EHCI Host Controller <6>[ 5.432137] ehci-platform 5800d000.usbh-ehci: new USB bus registered, assigned bus number 2 <6>[ 5.440952] ehci-platform 5800d000.usbh-ehci: irq 64, io mem 0x5800d000 <6>[ 5.472001] ehci-platform 5800d000.usbh-ehci: USB 2.0 started, EHCI 1.00 <6>[ 5.478661] hub 2-0:1.0: USB hub found <6>[ 5.481590] hub 2-0:1.0: 2 ports detected <6>[ 5.490223] mmci-pl18x 58007000.sdmmc: mmc2: PL180 manf 53 rev1 at 0x58007000 irq 62,0 (pio) <6>[ 5.603933] stm32-dwmac 5800a000.ethernet eth0: PHY [stmmac-0:07] driver [Micrel KSZ9031 Gigabit PHY] (irq=POLL) <6>[ 5.614186] dwmac4: Master AXI performs any burst length <6>[ 5.618545] stm32-dwmac 5800a000.ethernet eth0: No Safety Features support found <6>[ 5.826296] stm32-dwmac 5800a000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported <6>[ 5.833930] stm32-dwmac 5800a000.ethernet eth0: registered PTP clock <6>[ 5.840858] stm32-dwmac 5800a000.ethernet eth0: configuring for phy/rgmii link mode <6>[ 5.871495] mmc2: new DDR MMC card at address 0001 <6>[ 5.876048] mmcblk2: mmc2:0001 DG4008 7.28 GiB <6>[ 5.880129] mmcblk2boot0: mmc2:0001 DG4008 partition 1 4.00 MiB <6>[ 5.886461] mmcblk2boot1: mmc2:0001 DG4008 partition 2 4.00 MiB <6>[ 5.892633] mmcblk2rpmb: mmc2:0001 DG4008 partition 3 4.00 MiB, chardev (235:0) <4>[ 5.905864] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 5.912184] GPT:3145727 != 15273599 <4>[ 5.915839] GPT:Alternate GPT header not at the end of the disk. <4>[ 5.922148] GPT:3145727 != 15273599 <4>[ 5.925865] GPT: Use GNU Parted to correct GPT errors. <6>[ 5.931342] mmcblk2: p1 p2 p3 p4 <6>[ 6.002005] usb 2-1: new high-speed USB device number 2 using ehci-platform <6>[ 6.203416] hub 2-1:1.0: USB hub found <6>[ 6.206155] hub 2-1:1.0: 3 ports detected <6>[ 15.293705] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 15.312035] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 15.341995] Sending DHCP requests ..., OK <6>[ 21.624880] IP-Config: Got DHCP answer from 192.168.56.254, my address is 192.168.56.204 <6>[ 21.633224] IP-Config: Complete: <6>[ 21.636678] device=eth0, hwaddr=80:1f:12:cc:2a:a4, ipaddr=192.168.56.204, mask=255.255.255.0, gw=192.168.56.254 <6>[ 21.647516] host=192.168.56.204, domain=mayfield.sirena.org.uk, nis-domain=(none) <6>[ 21.655710] bootserver=192.168.56.254, rootserver=192.168.56.254, rootpath= <6>[ 21.655718] nameserver0=192.168.56.254 <6>[ 21.667799] ntpserver0=50.205.244.22, ntpserver1=85.199.214.99 <6>[ 21.680549] Freeing unused kernel memory: 2048K <6>[ 21.712450] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 21.881783] udevd[113]: starting version 3.2.9 <27>[ 21.899453] udevd[113]: specified user 'tss' unknown <27>[ 21.903834] udevd[113]: specified group 'tss' unknown <30>[ 21.911829] udevd[114]: starting eudev-3.2.9 <5>[ 23.106828] cfg80211: Loading compiled-in X.509 certificates for regulatory database <6>[ 23.421889] Bluetooth: Core ver 2.22 <6>[ 23.424583] NET: Registered protocol family 31 <6>[ 23.429006] Bluetooth: HCI device and connection manager initialized <6>[ 23.435779] Bluetooth: HCI socket layer initialized <6>[ 23.440779] Bluetooth: L2CAP socket layer initialized <6>[ 23.446180] Bluetooth: SCO socket layer initialized <6>[ 23.457930] Bluetooth: HCI UART driver ver 2.3 <6>[ 23.461201] Bluetooth: HCI UART protocol H4 registered <6>[ 23.467767] Bluetooth: HCI UART protocol Broadcom registered <4>[ 23.473155] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator <4>[ 23.480622] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator <6>[ 23.771775] etnaviv etnaviv: bound 59000000.gpu (ops gpu_ops [etnaviv]) <6>[ 23.777400] etnaviv-gpu 59000000.gpu: model: GC400, revision: 4652 <5>[ 23.798559] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>[ 23.844202] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 23.851828] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 23.860231] cfg80211: failed to load regulatory.db <6>[ 23.883893] etnaviv-gpu 59000000.gpu: Need to move linear window on MC1.0, disabling TS <6>[ 23.930727] Bluetooth: hci0: BCM: chip id 107 <6>[ 23.934670] Bluetooth: hci0: BCM: features 0x2f <6>[ 23.942676] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 23.963325] Bluetooth: hci0: BCM4345C0 <6>[ 23.965903] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0000 <3>[ 23.972369] Bluetooth: hci0: BCM: firmware Patch file not found, tried: <3>[ 23.978973] Bluetooth: hci0: BCM: 'brcm/BCM4345C0.hcd' <3>[ 23.984442] Bluetooth: hci0: BCM: 'brcm/BCM.hcd' <6>[ 24.001835] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 <4>[ 24.009988] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2 <6>[ 24.408391] [drm] Initialized stm 1.0.0 20170330 for 5a001000.display-controller on minor 1 <6>[ 24.423175] stm32-display 5a001000.display-controller: [drm] Cannot find any crtc or sizes <6>[ 24.460506] stm32-display 5a001000.display-controller: [drm] Cannot find any crtc or sizes <3>[ 25.082693] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-579654/environment . /lava-579654/environment / # /lava-579654/bin/lava-test-runner /lava-579654/0 /lava-579654/bin/lava-test-runner /lava-579654/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-579654/0/tests/0_dmesg + cat uuid + UUID=579654_1.5.2.<8>[ 25.936588] 4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 25.990121] <8>[ 26.039664] <8>[ 26.088815] + set +x <8>[ 26.098193] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-579654/environment / # . /lava-579654/environment/lava-579654/bin/lava-test-runner /lava-579654/1 / # /lava-579654/bin/lava-test-runner /lava-579654/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-579654/1/tests/1_bootrr + cat uuid + UUID=579654_1.5.2.<8>[ 26.603241] 4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-579654/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-579654/1/../bin/lava-test-case <8>[ 26.669384] /lava-579654/1/../bin/lava-test-case <8>[ 26.716936] /lava-579654/1/../bin/lava-test-case <8>[ 26.745869] + set +x <8>[ 26.769192] / #