[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12757636/tftp-deploy-gnj6hi_5/kernel/zImage tftp 0x10000000 12757636/tftp-deploy-gnj6hi_5/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12757636/tftp-deploy-gnj6hi_5/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 14.2 MiB/s done Bytes transferred = 9716224 (944200 hex) => tftp 0x14000000 12757636/tftp-deploy-gnj6hi_5/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12757636/tftp-deploy-gnj6hi_5/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12757636/tftp-deploy-gnj6hi_5/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 14 MiB/s done Bytes transferred = 16082687 (f566ff hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12757636/tftp-deploy-gnj6hi_5/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12757636/tftp-deploy-gnj6hi_5/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12757636/tftp-deploy-gnj6hi_5/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x944200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16082623 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.209-cip44 (KernelCI@build-j106860-arm-gcc-10-multi-v7-defconfig-6hp2s) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Feb 13 17:16:56 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932648K/1048576K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 50392K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022181] Console: colour dummy device 80x30 <6>[ 0.024071] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034480] CPU: Testing write buffer coherency: ok <6>[ 0.039613] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044911] pid_max: default: 32768 minimum: 301 <6>[ 0.049938] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057377] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066247] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071974] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079687] rcu: Hierarchical SRCU implementation. <6>[ 0.086679] EFI services will not be available. <6>[ 0.088914] smp: Bringing up secondary CPUs ... <6>[ 0.094202] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094211] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105541] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105548] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116744] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116752] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127195] smp: Brought up 1 node, 4 CPUs <6>[ 0.131422] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137880] CPU: All CPU(s) started in SVC mode. <6>[ 0.143306] devtmpfs: initialized <6>[ 0.153530] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158871] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168743] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.178962] pinctrl core: initialized pinctrl subsystem <6>[ 0.183467] DMI not present or invalid. <6>[ 0.186547] NET: Registered protocol family 16 <6>[ 0.193864] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200496] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200677] cpuidle: using governor menu <6>[ 0.208779] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.389683] vdd1p1: supplied by regulator-dummy <6>[ 0.398912] vdd3p0: supplied by regulator-dummy <6>[ 0.408015] vdd2p5: supplied by regulator-dummy <6>[ 0.417165] vddarm: supplied by regulator-dummy <6>[ 0.426491] vddpu: supplied by regulator-dummy <6>[ 0.435383] vddsoc: supplied by regulator-dummy <6>[ 0.767660] No ATAGs? <6>[ 0.767846] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.775602] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.785854] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.796146] Serial: AMBA PL011 UART driver <6>[ 0.800324] printk: console [ramoops-1] enabled <6>[ 0.802650] pstore: Registered ramoops as persistent store backend <6>[ 0.808904] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.846601] iommu: Default domain type: Translated <6>[ 0.849309] vgaarb: loaded <5>[ 0.852724] SCSI subsystem initialized <6>[ 0.856445] usbcore: registered new interface driver usbfs <6>[ 0.861638] usbcore: registered new interface driver hub <6>[ 0.867239] usbcore: registered new device driver usb <6>[ 0.874014] i2c i2c-0: IMX I2C adapter registered <6>[ 0.878786] i2c i2c-1: IMX I2C adapter registered <6>[ 0.883209] i2c i2c-2: IMX I2C adapter registered <6>[ 0.888723] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.892566] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.901999] PTP clock support registered <6>[ 0.909765] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.024524] NET: Registered protocol family 2 <6>[ 2.026727] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.035350] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.042623] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.050670] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.058096] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.064813] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.071512] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.078937] NET: Registered protocol family 1 <6>[ 2.084004] RPC: Registered named UNIX socket transport module. <6>[ 2.089545] RPC: Registered udp transport module. <6>[ 2.094546] RPC: Registered tcp transport module. <6>[ 2.099462] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.106190] PCI: CLS 0 bytes, default 64 <6>[ 2.110876] Trying to unpack rootfs image as initramfs... <6>[ 3.459579] Freeing initrd memory: 15708K <4>[ 3.461477] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.468877] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.478643] Initialise system trusted keyrings <6>[ 3.481789] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.493920] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.497885] NFS: Registering the id_resolver key type <5>[ 3.502529] Key type id_resolver registered <5>[ 3.506910] Key type id_legacy registered <6>[ 3.511285] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.518134] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.525836] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.530899] Key type asymmetric registered <5>[ 3.534752] Asymmetric key parser 'x509' registered <6>[ 3.539952] bounce: pool size: 64 pages <6>[ 3.544004] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.551649] io scheduler mq-deadline registered <6>[ 3.556414] io scheduler kyber registered <6>[ 3.600585] mxs-dma 110000.dma-controller: initialized <4>[ 3.607886] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.615701] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.666893] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.675059] SuperH (H)SCI(F) driver initialized <6>[ 3.678002] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.686891] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.694802] printk: console [ttymxc1] enabled <6>[ 3.694802] printk: console [ttymxc1] enabled <6>[ 3.703978] printk: bootconsole [ec_imx21] disabled <6>[ 3.703978] printk: bootconsole [ec_imx21] disabled <6>[ 3.715822] msm_serial: driver initialized <6>[ 3.721736] STMicroelectronics ASC driver initialized <6>[ 3.729043] STM32 USART driver initialized <4>[ 3.743976] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.751911] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.758703] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.775587] brd: module loaded <6>[ 3.786477] loop: module loaded <6>[ 3.793904] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.802130] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.810417] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.818866] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.826882] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.834626] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.842188] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.852774] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.860060] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.869121] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.879956] scsi host0: ahci-imx <6>[ 3.883808] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.904596] CAN device driver interface <6>[ 3.910103] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.919628] pps pps0: new PPS source ptp0 <6>[ 3.956748] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.964403] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.969638] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.975908] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.981593] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.993704] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.001435] usbcore: registered new interface driver pegasus <6>[ 4.007401] usbcore: registered new interface driver asix <6>[ 4.013118] usbcore: registered new interface driver ax88179_178a <6>[ 4.019521] usbcore: registered new interface driver cdc_ether <6>[ 4.025684] usbcore: registered new interface driver smsc75xx <6>[ 4.031758] usbcore: registered new interface driver smsc95xx <6>[ 4.037804] usbcore: registered new interface driver net1080 <6>[ 4.043779] usbcore: registered new interface driver cdc_subset <6>[ 4.050010] usbcore: registered new interface driver zaurus <6>[ 4.055933] usbcore: registered new interface driver cdc_ncm <6>[ 4.065512] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.072330] ehci-pci: EHCI PCI platform driver <6>[ 4.077077] ehci-platform: EHCI generic platform driver <6>[ 4.082907] ehci-orion: EHCI orion driver <6>[ 4.087418] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.091918] ehci-st: EHCI STMicroelectronics driver <6>[ 4.097259] ehci-exynos: EHCI Exynos driver <6>[ 4.101911] ehci-atmel: EHCI Atmel driver <6>[ 4.106372] tegra-ehci: Tegra EHCI driver <6>[ 4.110891] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.117372] ohci-pci: OHCI PCI platform driver <6>[ 4.122146] ohci-platform: OHCI generic platform driver <6>[ 4.127917] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.132414] ohci-st: OHCI STMicroelectronics driver <6>[ 4.137764] ohci-atmel: OHCI Atmel driver <6>[ 4.143362] usbcore: registered new interface driver usb-storage <6>[ 4.158106] i2c /dev entries driver <6>[ 4.182224] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.188677] sdhci: Copyright(c) Pierre Ossman <6>[ 4.196180] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.204495] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.215846] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.216071] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.221164] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.231845] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.239249] usbcore: registered new interface driver usbhid <6>[ 4.240739] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.245117] usbhid: USB HID core driver <6>[ 4.250817] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.258157] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.261419] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.261727] NET: Registered protocol family 10 <6>[ 4.262507] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.288837] Segment Routing with IPv6 <6>[ 4.292892] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.299666] NET: Registered protocol family 17 <6>[ 4.303236] mmc2: new high speed SDHC card at address 0001 <6>[ 4.304414] can: controller area network core <6>[ 4.314869] NET: Registered protocol family 29 <6>[ 4.319583] can: raw protocol <6>[ 4.320429] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 4.322854] can: broadcast manager protocol <6>[ 4.331755] can: netlink gateway - max_hops=1 <5>[ 4.336879] Key type dns_resolver registered <4>[ 4.340524] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.349088] GPT:29296874 != 30965759 <6>[ 4.351103] ThumbEE CPU extension supported. <4>[ 4.352966] GPT:Alternate GPT header not at the end of the disk. <5>[ 4.357476] Registering SWP/SWPB emulation handler <4>[ 4.363753] GPT:29296874 != 30965759 <4>[ 4.363757] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.363808] mmcblk2: p1 p2 p3 <5>[ 4.372811] Loading compiled-in X.509 certificates <6>[ 4.391687] pstore: Using crash dump compression: deflate <4>[ 4.419651] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.427594] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.435576] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.451989] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.461991] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.467165] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.499862] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.507022] hub 1-0:1.0: USB hub found <6>[ 4.511171] hub 1-0:1.0: 1 port detected <6>[ 4.519832] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.535152] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.543078] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.551025] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.563195] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.571108] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.578963] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.589080] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.601378] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.609253] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.617209] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.631354] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.839795] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.041427] hub 1-1:1.0: USB hub found <6>[ 5.045650] hub 1-1:1.0: 3 ports detected <4>[ 5.056323] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.064305] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.072594] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.760276] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.789871] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.819849] Sending DHCP requests ., OK <6>[ 7.863990] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 7.872328] IP-Config: Complete: <6>[ 7.875848] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.886619] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 7.894770] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.894782] nameserver0=192.168.201.1 <6>[ 7.915772] Freeing unused kernel memory: 2048K <6>[ 7.940254] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.060588] udevd[137]: starting version 3.2.9 <5>[ 8.066181] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.073283] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.080117] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.093970] udevd[137]: specified user 'tss' unknown <27>[ 8.099417] udevd[137]: specified group 'tss' unknown <30>[ 8.107156] udevd[138]: starting eudev-3.2.9 <6>[ 8.390882] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.397769] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.410045] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.417991] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.444944] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.482308] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.490313] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.549840] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.557995] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.566724] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.574867] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.585007] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.600001] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.608027] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.666864] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.675505] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.684220] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.692814] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.704666] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.734761] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.742734] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.820617] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.846486] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.859914] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.869969] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.876782] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.926035] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.986800] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.992243] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.999127] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 9.009085] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 9.017847] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 9.024253] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 9.032435] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 9.040809] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.049354] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.057923] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.066469] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.078374] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.100064] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.108124] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.119219] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.127770] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.136422] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.144999] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.176117] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.182738] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 9.190335] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 9.196598] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 9.198698] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.223046] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.231616] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.240178] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.248685] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.259248] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.276597] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.284642] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.295389] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.303953] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.312542] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.321062] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.561701] caam algorithms registered in /proc/crypto <6>[ 9.568513] caam 2100000.crypto: registering rng-caam <4>[ 9.575720] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.598599] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.606539] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.616179] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.624698] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.633261] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done <6>[ 9.641788] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Saving random seed: <4>[ 9.652812] panel-simple panel-lvds0: supply power not found, using dummy regulator <5>[ 9.660448] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 9.753000] random: dropbear: uninitialized urandom read (32 bytes read) <5>[ 9.756416] random: crng init done <5>[ 9.763713] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12757636/environment . /lava-12757636/environment / # /lava-12757636/bin/lava-test-runner /lava-12757636/0 /lava-12757636/bin/lava-test-runner /lava-12757636/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12757636/0/tests/0_dmesg + <8>[ 10.367898] cat uuid + UUID=12757636_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.411482] <8>[ 10.452459] <8>[ 10.493446] + set<8>[ 10.503349] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12757636/environment / # . /lava-12757636/environment/lava-12757636/bin/lava-test-runner /lava-12757636/1 / # /lava-12757636/bin/lava-test-runner /lava-12757636/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12757636/1/tests/1_bootrr <8>[ 11.007523] + cat uuid + UUID=12757636_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12757636/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd 120000.hdmi panel-lvds0 /lava-12757636/1/../bin/lava-test-case <8>[ 12.083357] /lava-12757636/1/../bin/lava-test-case <8>[ 12.122513] /lava-12757636/1/../bin/lava-test-case <8>[ 12.147539] + set<8>[ 12.166525] +x / #