Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.91 (1257 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 426201/tftp-deploy-wnc4wn26/kernel/Image tftp 0x82000000 426201/tftp-deploy-wnc4wn26/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '426201/tftp-deploy-wnc4wn26/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## 18.3 MiB/s done Bytes transferred = 44087808 (2a0ba00 hex) => tftp 0x90080000 426201/tftp-deploy-wnc4wn26/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 426201/tftp-deploy-wnc4wn26/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '426201/tftp-deploy-wnc4wn26/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################### 14.4 MiB/s done Bytes transferred = 21442661 (1473065 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 426201/tftp-deploy-wnc4wn26/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 426201/tftp-deploy-wnc4wn26/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '426201/tftp-deploy-wnc4wn26/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 4.8 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-02-05 17:01:25 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 21442597 Bytes = 20.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.209-cip44 (KernelCI@build-j98971-arm64-gcc-10-defconfig-kselftest-9qds5) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Mon Feb 5 16:35:46 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7fc7c0-0x20ff7fefff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 34 pages/cpu s101072 r8192 d30000 u139264 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3872468K/4126720K available (18944K kernel code, 4654K rwdata, 9532K rodata, 9792K init, 11275K bss, 221484K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 59343 entries in 232 pages <6>[ 0.000000] ftrace: allocated 232 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080200000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x00000020801e0000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000020801f0000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000003] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008845] Console: colour dummy device 80x25 <4>[ 0.013623] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.021720] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026131] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030628] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035300] ... CLASSHASH_SIZE: 4096 <4>[ 0.039973] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.044733] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049493] ... CHAINHASH_SIZE: 32768 <4>[ 0.054253] memory used by lock dependency info: 6365 kB <4>[ 0.059979] memory used for stack traces: 4224 kB <4>[ 0.065090] per task-struct memory footprint: 1920 bytes <6>[ 0.070898] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.081639] pid_max: default: 32768 minimum: 301 <6>[ 0.086703] LSM: Security Framework initializing <6>[ 0.091672] LSM support for eBPF active <6>[ 0.095894] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.103668] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.115527] rcu: Hierarchical SRCU implementation. <6>[ 0.123083] Platform MSI: gic-its@6020000 domain created <6>[ 0.128880] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.136812] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.142998] EFI services will not be available. <6>[ 0.148261] smp: Bringing up secondary CPUs ... <6>[ 0.154377] Detected PIPT I-cache on CPU1 <6>[ 0.154399] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.154408] GICv3: CPU1: using allocated LPI pending table @0x0000002080280000 <6>[ 0.154451] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.154850] smp: Brought up 1 node, 2 CPUs <6>[ 0.185306] SMP: Total of 2 processors activated. <6>[ 0.190345] CPU features: detected: 32-bit EL0 Support <6>[ 0.195876] CPU features: detected: CRC32 instructions <6>[ 0.201369] CPU features: detected: 32-bit EL1 Support <6>[ 0.236246] CPU: All CPU(s) started at EL2 <6>[ 0.240718] alternatives: patching kernel code <6>[ 0.247452] devtmpfs: initialized <4>[ 0.264485] KASLR disabled due to lack of seed <6>[ 0.270359] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.280506] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.288662] pinctrl core: initialized pinctrl subsystem <6>[ 0.296980] DMI not present or invalid. <6>[ 0.302131] NET: Registered protocol family 16 <6>[ 0.309991] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.317552] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.326065] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.334453] audit: initializing netlink subsys (disabled) <5>[ 0.340500] audit: type=2000 audit(0.228:1): state=initialized audit_enabled=0 res=1 <6>[ 0.342551] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.348622] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.355755] cpuidle: using governor menu <6>[ 0.367177] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.374403] ASID allocator initialised with 65536 entries <6>[ 0.382571] Serial: AMBA PL011 UART driver <6>[ 0.442758] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.450435] SoC family: QorIQ LS1028A <6>[ 0.454397] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.501224] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.508319] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.515370] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.522423] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.532429] cryptd: max_cpu_qlen set to 1000 <6>[ 0.542554] ACPI: Interpreter disabled. <6>[ 0.551125] iommu: Default domain type: Translated <6>[ 0.557073] vgaarb: loaded <5>[ 0.560904] SCSI subsystem initialized <6>[ 0.565819] usbcore: registered new interface driver usbfs <6>[ 0.571771] usbcore: registered new interface driver hub <6>[ 0.577482] usbcore: registered new device driver usb <6>[ 0.583933] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.593106] i2c i2c-0: IMX I2C adapter registered <6>[ 0.599224] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.607379] i2c i2c-1: IMX I2C adapter registered <6>[ 0.612870] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.621412] i2c i2c-2: IMX I2C adapter registered <6>[ 0.627492] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.632790] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.642361] PTP clock support registered <6>[ 0.646892] EDAC MC: Ver: 3.0.0 <6>[ 0.653728] FPGA manager framework <6>[ 0.657694] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.665851] clocksource: Switched to clocksource arch_sys_counter <5>[ 1.397503] VFS: Disk quotas dquot_6.6.0 <6>[ 1.401869] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 1.409717] pnp: PnP ACPI: disabled <6>[ 1.429923] NET: Registered protocol family 2 <6>[ 1.434969] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.445092] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 163840 bytes, linear) <6>[ 1.454389] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.463287] TCP bind hash table entries: 32768 (order: 9, 2359296 bytes, linear) <6>[ 1.475564] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.483244] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.491779] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.499547] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.507929] NET: Registered protocol family 1 <6>[ 1.513802] RPC: Registered named UNIX socket transport module. <6>[ 1.520097] RPC: Registered udp transport module. <6>[ 1.525133] RPC: Registered tcp transport module. <6>[ 1.530166] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.536965] NET: Registered protocol family 44 <6>[ 1.541751] PCI: CLS 0 bytes, default 64 <6>[ 1.546481] Unpacking initramfs... <6>[ 2.686439] Freeing initrd memory: 20936K <6>[ 2.691636] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 2.700539] kvm [1]: IPA Size Limit: 44 bits <6>[ 2.711794] kvm [1]: GICv3: no GICV resource entry <6>[ 2.716922] kvm [1]: disabling GICv2 emulation <6>[ 2.721724] kvm [1]: GIC system register CPU interface enabled <6>[ 2.728016] kvm [1]: vgic interrupt IRQ9 <6>[ 2.732417] kvm [1]: Hyp mode initialized successfully <5>[ 2.742503] Initialise system trusted keyrings <6>[ 2.747640] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 2.778848] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.786527] NFS: Registering the id_resolver key type <5>[ 2.791965] Key type id_resolver registered <5>[ 2.796483] Key type id_legacy registered <6>[ 2.801066] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.808136] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.816204] 9p: Installing v9fs 9p2000 file system support <5>[ 2.853486] Key type asymmetric registered <5>[ 2.857950] Asymmetric key parser 'x509' registered <6>[ 2.863225] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 2.870998] io scheduler mq-deadline registered <6>[ 2.875858] io scheduler kyber registered <4>[ 2.880562] test_firmware: interface ready <6>[ 2.907924] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 2.916119] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 2.925348] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 2.934569] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 2.943800] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 2.953021] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 2.962240] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 2.971430] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 2.980719] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 2.990130] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 2.997458] pci_bus 0000:00: root bus resource [bus 00] <6>[ 3.003034] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 3.013775] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 3.025019] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 3.035762] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 3.046941] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 3.057681] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 3.068869] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 3.079697] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 3.086215] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.097049] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.108321] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 3.119413] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 3.131035] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 3.136914] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 3.147214] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 3.158609] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 3.165084] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.175919] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.187190] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 3.198296] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 3.209922] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 3.215781] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 3.226080] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 3.237388] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 3.243883] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.254717] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.266068] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 3.272420] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 3.278913] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.289747] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.301087] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 3.307431] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 3.313918] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.324752] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.336102] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 3.342473] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 3.348945] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.359779] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.371050] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.381951] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 3.388315] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 3.394796] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.405630] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.416969] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 3.424163] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 3.430729] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 3.439188] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 3.447277] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 3.455554] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 3.463307] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 3.472274] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 3.481503] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.488563] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.494389] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.500917] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.511879] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.518436] pci 0001:00:00.0: supports D1 D2 <6>[ 3.523032] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.531524] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.538502] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.544393] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.552142] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.561077] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.570276] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.577335] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.583174] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.592512] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.603470] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.610030] pci 0002:00:00.0: supports D1 D2 <6>[ 3.614626] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.623097] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.630071] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 3.639066] EINJ: ACPI disabled. <6>[ 3.676666] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.690857] printk: console [ttyS0] disabled <6>[ 3.695669] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 3.705024] printk: console [ttyS0] enabled <6>[ 3.705024] printk: console [ttyS0] enabled <6>[ 3.714007] printk: bootconsole [ns16550a0] disabled <6>[ 3.714007] printk: bootconsole [ns16550a0] disabled <6>[ 3.726473] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 3.736773] SuperH (H)SCI(F) driver initialized <6>[ 3.742715] msm_serial: driver initialized <6>[ 3.748355] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 3.763699] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.770492] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.775413] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.781028] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.786643] arm-smmu 5000000.iommu: nested translation <5>[ 3.792175] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.799625] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.806467] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.813217] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.819975] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 3.845463] loop: module loaded <6>[ 3.850089] lkdtm: No crash points registered, enable through debugfs <6>[ 3.880483] megasas: 07.714.04.00-rc1 <6>[ 3.893869] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 3.919796] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 3.937498] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 3.944649] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 3.950189] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 3.960090] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 3.972004] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 3.984050] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 3.995993] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 4.007980] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.020001] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.031995] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.053020] thunder_xcv, ver 1.0 <6>[ 4.056674] thunder_bgx, ver 1.0 <6>[ 4.060312] nicpf, ver 1.0 <6>[ 4.065527] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 4.177898] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.184526] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using ce:7d:2c:4f:e1:bd <6>[ 4.193380] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 9e:77:69:15:08:11 <6>[ 4.223884] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 4.337897] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 4.346913] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 4.353584] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 4.465898] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 4.473328] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 4.480001] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 4.593897] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 4.601315] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 4.608166] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 4.721893] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.730285] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 4.736776] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.743954] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.753364] pps pps0: new PPS source ptp0 <6>[ 4.759376] hclge is initializing <6>[ 4.763087] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.770623] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.776366] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.781547] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.787725] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.792993] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.799342] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.805045] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.811010] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.817584] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.824703] sky2: driver version 1.30 <6>[ 4.831338] VFIO - User Level meta-driver version: 0.3 <6>[ 4.838158] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 4.845709] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 4.856221] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.863112] ehci-pci: EHCI PCI platform driver <6>[ 4.867951] ehci-platform: EHCI generic platform driver <6>[ 4.873767] ehci-orion: EHCI orion driver <6>[ 4.878334] ehci-exynos: EHCI Exynos driver <6>[ 4.883082] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.889598] ohci-pci: OHCI PCI platform driver <6>[ 4.894449] ohci-platform: OHCI generic platform driver <6>[ 4.900250] ohci-exynos: OHCI Exynos driver <6>[ 4.905658] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.911598] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.919916] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 4.929715] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 4.936516] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.942328] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.950314] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.959137] hub 1-0:1.0: USB hub found <6>[ 4.963306] hub 1-0:1.0: 1 port detected <6>[ 4.968650] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.978462] hub 2-0:1.0: USB hub found <6>[ 4.982580] hub 2-0:1.0: 1 port detected <6>[ 4.987855] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.993788] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 5.002125] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 5.011998] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 5.018791] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 5.024602] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 5.032586] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.040779] hub 3-0:1.0: USB hub found <6>[ 5.044911] hub 3-0:1.0: 1 port detected <6>[ 5.050013] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.059694] hub 4-0:1.0: USB hub found <6>[ 5.063816] hub 4-0:1.0: 1 port detected <6>[ 5.069635] usbcore: registered new interface driver usb-storage <6>[ 5.082987] i2c /dev entries driver <6>[ 5.099481] sp805-wdt c000000.watchdog: registration successful <6>[ 5.106229] sp805-wdt c010000.watchdog: registration successful <6>[ 5.118094] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 5.129253] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.136304] sdhci: Copyright(c) Pierre Ossman <6>[ 5.142339] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.151412] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.159209] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 5.161675] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 5.171349] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.182093] usbcore: registered new interface driver usbhid <6>[ 5.188031] usbhid: USB HID core driver <6>[ 5.193737] mmc0: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 5.197913] mmc1: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 5.208806] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.216502] IPv4 over IPsec tunneling driver <6>[ 5.222963] NET: Registered protocol family 10 <6>[ 5.230789] Segment Routing with IPv6 <6>[ 5.236997] NET: Registered protocol family 17 <6>[ 5.242618] 8021q: 802.1Q VLAN Support v1.8 <6>[ 5.247475] 9pnet: Installing 9P2000 support <5>[ 5.252239] Key type dns_resolver registered <6>[ 5.257524] registered taskstats version 1 <5>[ 5.262266] Loading compiled-in X.509 certificates <6>[ 5.284588] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 5.298781] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 5.305368] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 5.305911] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 5.312477] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 5.325084] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 5.336244] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.354532] mmc1: new HS400 MMC card at address 0001 <6>[ 5.361426] mmcblk1: mmc1:0001 S0J56X 7.34 GiB <6>[ 5.366965] mmcblk1boot0: mmc1:0001 S0J56X partition 1 31.5 MiB <6>[ 5.373677] mmcblk1boot1: mmc1:0001 S0J56X partition 2 31.5 MiB <6>[ 5.380380] mmcblk1rpmb: mmc1:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 5.391742] mmcblk1: p1 p2 <6>[ 5.407992] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.427520] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.521253] hub 3-1:1.0: USB hub found <6>[ 5.525976] hub 3-1:1.0: 7 ports detected <6>[ 8.497457] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 8.510228] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.530052] Sending DHCP requests ., OK <6>[ 8.550564] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.91 <6>[ 8.558734] IP-Config: Complete: <6>[ 8.562408] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.91, mask=255.255.255.0, gw=172.16.0.254 <6>[ 8.572935] host=172.16.0.91, domain=lava.lan, nis-domain=(none) <6>[ 8.579802] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.579837] nameserver0=8.8.8.8 <6>[ 8.594049] ALSA device list: <6>[ 8.597570] No soundcards found. <6>[ 8.638124] Freeing unused kernel memory: 9792K <6>[ 8.643297] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.818221] udevd[131]: starting version 3.2.9 <5>[ 8.824685] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.832159] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.838985] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.851646] udevd[131]: specified user 'tss' unknown <27>[ 8.857116] udevd[131]: specified group 'tss' unknown <30>[ 8.865800] udevd[132]: starting eudev-3.2.9 <27>[ 9.809587] udevd[143]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 9.836167] mali-dp f080000.display: Adding to iommu group 13 <6>[ 9.859767] mscc_felix 0000:00:00.5: Adding to iommu group 14 <4>[ 9.889446] at24 0-0050: supply vcc not found, using dummy regulator <28>[ 9.902372] udevd[143]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 9.910209] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 9.917758] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 9.961448] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 9.985969] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 9.993787] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 10.015565] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 10.023008] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 10.030146] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 10.037535] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 10.045649] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 10.053547] wm8904 2-001a: revision A <6>[ 10.058502] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 10.062600] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 10.074386] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 10.084590] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 10.093710] rtc-rv8803 0-0032: registered as rtc0 <6>[ 10.093908] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <4>[ 10.108642] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 10.115234] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 10.349647] caam 8000000.crypto: Entropy delay = 3200 <6>[ 10.389658] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 10.444935] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 10.450461] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 10.458212] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 10.737464] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 10.745827] caam algorithms registered in /proc/crypto <6>[ 10.759059] caam 8000000.crypto: registering rng-caam <6>[ 10.766605] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 10.773659] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 10.780511] caam_jr 8040000.jr: Adding to iommu group 18 done <5>[ 10.825481] random: crng init done <5>[ 10.829543] random: 2 urandom warning(s) missed due to ratelimiting Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-426201/environment . /lava-426201/environment / # /lava-426201/bin/lava-test-runner /lava-426201/0 /lava-426201/bin/lava-test-runner /lava-426201/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-426201/0/tests/0_dmesg + cat uuid + UUID=426201_1.5.<8>[ 11.558934] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.610182] <8>[ 11.661020] <8>[ 11.720362] + set +x<8>[ 11.734686] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-426201/environment / # . /lava-426201/environment/lava-426201/bin/lava-test-runner /lava-426201/1 / # /lava-426201/bin/lava-test-runner /lava-426201/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-426201/1/tests/1_bootrr + cat uuid + UUID=426201_1.<8>[ 12.245461] 5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-426201/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-426201/1/../bin/lava-test-case <8>[ 12.306878] /lava-426201/1/../bin/lava-test-case <8>[ 12.353721] /lava-426201/1/../bin/lava-test-case <8>[ 12.382634] /lava-426201/1/../bin/lava-test-case <8>[ 12.445369] /lava-426201/1/../bin/lava-test-case <8>[ 12.492915] /lava-426201/1/../bin/lava-test-case <8>[ 12.532669] /lava-426201/1/../bin/lava-test-case <8>[ 12.582636] /lava-426201/1/../bin/lava-test-case <8>[ 12.624023] /lava-426201/1/../bin/lava-test-case <8>[ 12.673751] /lava-426201/1/../bin/lava-test-case <8>[ 12.712151] /lava-426201/1/../bin/lava-test-case <8>[ 12.760238] /lava-426201/1/../bin/lava-test-case <8>[ 12.797670] /lava-426201/1/../bin/lava-test-case <8>[ 12.845677] /lava-426201/1/../bin/lava-test-case <8>[ 12.885774] /lava-426201/1/../bin/lava-test-case <8>[ 12.933421] /lava-426201/1/../bin/lava-test-case <8>[ 12.971955] /lava-426201/1/../bin/lava-test-case <8>[ 13.021103] /lava-426201/1/../bin/lava-test-case <8>[ 13.072225] /lava-426201/1/../bin/lava-test-case <8>[ 13.110553] /lava-426201/1/../bin/lava-test-case <8>[ 13.159235] /lava-426201/1/../bin/lava-test-case <8>[ 13.215025] /lava-426201/1/../bin/lava-test-case <8>[ 13.264192] /lava-426201/1/../bin/lava-test-case <8>[ 13.304573] /lava-426201/1/../bin/lava-test-case <8>[ 13.353801] /lava-426201/1/../bin/lava-test-case <8>[ 13.409557] /lava-426201/1/../bin/lava-test-case <8>[ 13.459099] /lava-426201/1/../bin/lava-test-case <8>[ 13.497414] /lava-426201/1/../bin/lava-test-case <8>[ 13.545555] /lava-426201/1/../bin/lava-test-case <8>[ 13.584410] /lava-426201/1/../bin/lava-test-case <8>[ 13.638566] /lava-426201/1/../bin/lava-test-case <8>[ 13.690594] /lava-426201/1/../bin/lava-test-case <8>[ 13.742060] /lava-426201/1/../bin/lava-test-case <8>[ 13.779973] /lava-426201/1/../bin/lava-test-case <8>[ 13.838858] /lava-426201/1/../bin/lava-test-case <8>[ 13.880282] /lava-426201/1/../bin/lava-test-case <8>[ 13.930034] /lava-426201/1/../bin/lava-test-case <8>[ 13.967762] /lava-426201/1/../bin/lava-test-case <8>[ 14.019051] /lava-426201/1/../bin/lava-test-case <8>[ 14.070394] /lava-426201/1/../bin/lava-test-case <8>[ 14.107801] /lava-426201/1/../bin/lava-test-case <8>[ 14.156818] /lava-426201/1/../bin/lava-test-case <8>[ 14.208156] /lava-426201/1/../bin/lava-test-case <8>[ 14.247936] /lava-426201/1/../bin/lava-test-case <8>[ 14.296953] /lava-426201/1/../bin/lava-test-case <8>[ 14.337968] /lava-426201/1/../bin/lava-test-case <8>[ 14.386442] /lava-426201/1/../bin/lava-test-case <8>[ 14.423362] /lava-426201/1/../bin/lava-test-case <8>[ 14.472875] /lava-426201/1/../bin/lava-test-case <8>[ 14.525042] /lava-426201/1/../bin/lava-test-case <8>[ 14.563707] /lava-426201/1/../bin/lava-test-case <8>[ 14.613887] /lava-426201/1/../bin/lava-test-case <8>[ 14.663438] /lava-426201/1/../bin/lava-test-case <8>[ 14.703966] /lava-426201/1/../bin/lava-test-case <8>[ 14.756020] /lava-426201/1/../bin/lava-test-case <8>[ 14.808005] /lava-426201/1/../bin/lava-test-case <8>[ 14.849163] /lava-426201/1/../bin/lava-test-case <8>[ 14.899058] /lava-426201/1/../bin/lava-test-case <8>[ 14.937549] /lava-426201/1/../bin/lava-test-case <8>[ 14.986047] /lava-426201/1/../bin/lava-test-case <8>[ 15.023595] /lava-426201/1/../bin/lava-test-case <8>[ 15.072718] /lava-426201/1/../bin/lava-test-case <8>[ 15.123999] /lava-426201/1/../bin/lava-test-case <8>[ 15.172708] /lava-426201/1/../bin/lava-test-case <8>[ 15.223918] /lava-426201/1/../bin/lava-test-case <8>[ 15.262248] /lava-426201/1/../bin/lava-test-case <8>[ 15.310311] /lava-426201/1/../bin/lava-test-case <8>[ 15.358972] /lava-426201/1/../bin/lava-test-case <8>[ 15.398286] /lava-426201/1/../bin/lava-test-case <8>[ 15.447289] /lava-426201/1/../bin/lava-test-case <8>[ 15.488161] /lava-426201/1/../bin/lava-test-case <8>[ 15.540908] /lava-426201/1/../bin/lava-test-case <8>[ 16.585481] /lava-426201/1/../bin/lava-test-case <8>[ 17.631322] /lava-426201/1/../bin/lava-test-case <8>[ 18.675343] /lava-426201/1/../bin/lava-test-case <8>[ 19.724267] /lava-426201/1/../bin/lava-test-case <8>[ 19.764154] /lava-426201/1/../bin/lava-test-case <8>[ 19.815794] /lava-426201/1/../bin/lava-test-case <8>[ 19.854556] /lava-426201/1/../bin/lava-test-case <8>[ 19.903513] /lava-426201/1/../bin/lava-test-case <8>[ 19.941912] /lava-426201/1/../bin/lava-test-case <8>[ 19.992628] /lava-426201/1/../bin/lava-test-case <8>[ 20.033322] /lava-426201/1/../bin/lava-test-case <8>[ 20.082745] /lava-426201/1/../bin/lava-test-case <8>[ 20.132016] /lava-426201/1/../bin/lava-test-case <8>[ 20.170423] /lava-426201/1/../bin/lava-test-case <8>[ 20.222795] /lava-426201/1/../bin/lava-test-case <8>[ 20.274547] /lava-426201/1/../bin/lava-test-case <8>[ 20.326507] /lava-426201/1/../bin/lava-test-case <8>[ 20.378383] /lava-426201/1/../bin/lava-test-case <8>[ 20.419412] /lava-426201/1/../bin/lava-test-case <8>[ 20.468919] /lava-426201/1/../bin/lava-test-case <8>[ 20.508013] /lava-426201/1/../bin/lava-test-case <8>[ 20.555969] /lava-426201/1/../bin/lava-test-case <8>[ 20.593938] /lava-426201/1/../bin/lava-test-case <8>[ 20.641528] /lava-426201/1/../bin/lava-test-case <8>[ 20.690870] /lava-426201/1/../bin/lava-test-case <8>[ 20.731682] /lava-426201/1/../bin/lava-test-case <8>[ 20.780137] /lava-426201/1/../bin/lava-test-case <8>[ 21.824366] /lava-426201/1/../bin/lava-test-case <8>[ 22.872138] + set<8>[ 22.895165] +x / #