[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no => setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff => dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.12 (8 ms) => setenv serverip 192.168.201.1 => tftp 0x10000000 14787056/tftp-deploy-9zf3hmii/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '14787056/tftp-deploy-9zf3hmii/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 4 MiB/s done Bytes transferred = 9777664 (953200 hex) => tftp 0x14000000 14787056/tftp-deploy-9zf3hmii/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '14787056/tftp-deploy-9zf3hmii/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 4.3 MiB/s done Bytes transferred = 16083207 (f56907 hex) => setenv initrd_size ${filesize} => tftp 0x13f00000 14787056/tftp-deploy-9zf3hmii/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '14787056/tftp-deploy-9zf3hmii/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.1 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x953200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16083143 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.221-cip50 (KernelCI@build-j261383-arm-gcc-12-multi-v7-defconfig-tb8ms) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Wed Jul 10 11:01:30 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932644K/1048576K available (14336K kernel code, 2240K rwdata, 5364K rodata, 2048K init, 427K bss, 50396K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008095] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.022189] Console: colour dummy device 80x30 <6>[ 0.024080] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034750] CPU: Testing write buffer coherency: ok <6>[ 0.039882] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.045181] pid_max: default: 32768 minimum: 301 <6>[ 0.050210] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057647] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066523] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072264] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080073] rcu: Hierarchical SRCU implementation. <6>[ 0.087253] EFI services will not be available. <6>[ 0.089488] smp: Bringing up secondary CPUs ... <6>[ 0.094786] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094794] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106165] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.106174] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117319] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117327] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127772] smp: Brought up 1 node, 4 CPUs <6>[ 0.131996] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.138541] CPU: All CPU(s) started in SVC mode. <6>[ 0.143967] devtmpfs: initialized <6>[ 0.154076] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159412] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169289] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179497] pinctrl core: initialized pinctrl subsystem <6>[ 0.184006] DMI not present or invalid. <6>[ 0.187098] NET: Registered protocol family 16 <6>[ 0.194409] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201120] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201300] cpuidle: using governor menu <6>[ 0.209324] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.448547] vdd1p1: supplied by regulator-dummy <6>[ 0.460047] vdd3p0: supplied by regulator-dummy <6>[ 0.471499] vdd2p5: supplied by regulator-dummy <6>[ 0.482999] vddarm: supplied by regulator-dummy <6>[ 0.494651] vddpu: supplied by regulator-dummy <6>[ 0.505876] vddsoc: supplied by regulator-dummy <6>[ 0.949159] No ATAGs? <6>[ 0.949347] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.957122] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.967490] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.978007] Serial: AMBA PL011 UART driver <6>[ 0.982230] printk: console [ramoops-1] enabled <6>[ 0.984499] pstore: Registered ramoops as persistent store backend <6>[ 0.990762] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 1.028398] iommu: Default domain type: Translated <6>[ 1.031113] vgaarb: loaded <5>[ 1.034499] SCSI subsystem initialized <6>[ 1.038281] usbcore: registered new interface driver usbfs <6>[ 1.043431] usbcore: registered new interface driver hub <6>[ 1.049021] usbcore: registered new device driver usb <6>[ 1.055877] i2c i2c-0: IMX I2C adapter registered <6>[ 1.060568] i2c i2c-1: IMX I2C adapter registered <6>[ 1.065009] i2c i2c-2: IMX I2C adapter registered <6>[ 1.070546] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.074362] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.083797] PTP clock support registered <6>[ 1.091513] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.102576] NET: Registered protocol family 2 <6>[ 2.104780] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.113179] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.120650] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.128724] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.136180] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.142876] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.149537] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.157024] NET: Registered protocol family 1 <6>[ 2.162090] RPC: Registered named UNIX socket transport module. <6>[ 2.167595] RPC: Registered udp transport module. <6>[ 2.172595] RPC: Registered tcp transport module. <6>[ 2.177512] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.184242] PCI: CLS 0 bytes, default 64 <6>[ 2.188888] Trying to unpack rootfs image as initramfs... <6>[ 3.515000] Freeing initrd memory: 15708K <4>[ 3.516938] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.524257] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.534046] Initialise system trusted keyrings <6>[ 3.537236] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.549387] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.553373] NFS: Registering the id_resolver key type <5>[ 3.557971] Key type id_resolver registered <5>[ 3.562404] Key type id_legacy registered <6>[ 3.566741] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.573619] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.581285] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.586361] Key type asymmetric registered <5>[ 3.590220] Asymmetric key parser 'x509' registered <6>[ 3.595416] bounce: pool size: 64 pages <6>[ 3.599470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.607119] io scheduler mq-deadline registered <6>[ 3.611896] io scheduler kyber registered <6>[ 3.656596] mxs-dma 110000.dma-controller: initialized <4>[ 3.664206] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.672014] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.735347] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.743637] SuperH (H)SCI(F) driver initialized <6>[ 3.746616] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.755478] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.763390] printk: console [ttymxc1] enabled <6>[ 3.763390] printk: console [ttymxc1] enabled <6>[ 3.772554] printk: bootconsole [ec_imx21] disabled <6>[ 3.772554] printk: bootconsole [ec_imx21] disabled <6>[ 3.784278] msm_serial: driver initialized <6>[ 3.790263] STMicroelectronics ASC driver initialized <6>[ 3.797643] STM32 USART driver initialized <4>[ 3.812710] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.820620] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.827544] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.844111] brd: module loaded <6>[ 3.854854] loop: module loaded <6>[ 3.862350] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.870543] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.878837] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.887297] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.895311] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.903066] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.910609] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.921208] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.928494] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.937569] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.948395] scsi host0: ahci-imx <6>[ 3.952273] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.973133] CAN device driver interface <6>[ 3.978617] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.988154] pps pps0: new PPS source ptp0 <6>[ 4.025098] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 4.032768] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.038003] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.044270] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.049936] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.062123] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.069830] usbcore: registered new interface driver pegasus <6>[ 4.075822] usbcore: registered new interface driver asix <6>[ 4.081546] usbcore: registered new interface driver ax88179_178a <6>[ 4.087940] usbcore: registered new interface driver cdc_ether <6>[ 4.094102] usbcore: registered new interface driver smsc75xx <6>[ 4.100159] usbcore: registered new interface driver smsc95xx <6>[ 4.106224] usbcore: registered new interface driver net1080 <6>[ 4.112212] usbcore: registered new interface driver cdc_subset <6>[ 4.118429] usbcore: registered new interface driver zaurus <6>[ 4.124357] usbcore: registered new interface driver cdc_ncm <6>[ 4.134007] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.140806] ehci-pci: EHCI PCI platform driver <6>[ 4.145580] ehci-platform: EHCI generic platform driver <6>[ 4.151378] ehci-orion: EHCI orion driver <6>[ 4.155927] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.160401] ehci-st: EHCI STMicroelectronics driver <6>[ 4.165764] ehci-exynos: EHCI Exynos driver <6>[ 4.170406] ehci-atmel: EHCI Atmel driver <6>[ 4.174894] tegra-ehci: Tegra EHCI driver <6>[ 4.179394] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.185875] ohci-pci: OHCI PCI platform driver <6>[ 4.190629] ohci-platform: OHCI generic platform driver <6>[ 4.196427] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.200920] ohci-st: OHCI STMicroelectronics driver <6>[ 4.206287] ohci-atmel: OHCI Atmel driver <6>[ 4.211886] usbcore: registered new interface driver usb-storage <6>[ 4.226688] i2c /dev entries driver <6>[ 4.251134] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.257618] sdhci: Copyright(c) Pierre Ossman <6>[ 4.265150] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.273503] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.280751] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.285163] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.286062] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.293018] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.302184] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.308722] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.316199] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.323598] usbcore: registered new interface driver usbhid <6>[ 4.328126] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.329446] usbhid: USB HID core driver <6>[ 4.336714] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.347654] NET: Registered protocol family 10 <6>[ 4.353607] Segment Routing with IPv6 <6>[ 4.357613] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.364387] NET: Registered protocol family 17 <6>[ 4.369110] can: controller area network core <6>[ 4.371902] mmc2: new high speed SDHC card at address 0001 <6>[ 4.373846] NET: Registered protocol family 29 <6>[ 4.380358] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 4.384244] can: raw protocol <6>[ 4.391952] can: broadcast manager protocol <6>[ 4.396421] can: netlink gateway - max_hops=1 <5>[ 4.401647] Key type dns_resolver registered <4>[ 4.401718] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 4.408027] ThumbEE CPU extension supported. <4>[ 4.413891] GPT:29296874 != 30965759 <5>[ 4.418426] Registering SWP/SWPB emulation handler <4>[ 4.422268] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.422273] GPT:29296874 != 30965759 <4>[ 4.422281] GPT: Use GNU Parted to correct GPT errors. <5>[ 4.427635] Loading compiled-in X.509 certificates <6>[ 4.433669] mmcblk2: p1 p2 p3 <6>[ 4.442791] pstore: Using crash dump compression: deflate <4>[ 4.482435] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.490345] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.498647] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.516002] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.526034] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.531206] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.561624] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.568758] hub 1-0:1.0: USB hub found <6>[ 4.572911] hub 1-0:1.0: 1 port detected <3>[ 4.581079] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 4.588706] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 4.597095] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 4.609369] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.617327] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.625563] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.638687] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.646629] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.654854] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.665269] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.678268] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.686254] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.694616] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.708387] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.921575] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.123214] hub 1-1:1.0: USB hub found <6>[ 5.127453] hub 1-1:1.0: 3 ports detected <4>[ 5.142057] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.150092] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.159997] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.802013] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.821605] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.851586] Sending DHCP requests ., OK <6>[ 6.895743] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.12 <6>[ 6.904076] IP-Config: Complete: <6>[ 6.907598] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.12, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.918359] host=imx6q-sabrelite-lava-cbg-1, domain=lava-rack, nis-domain=(none) <6>[ 6.926514] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.926527] nameserver0=192.168.201.1 <6>[ 6.938688] clk: Disabling unused clocks <6>[ 6.949776] Freeing unused kernel memory: 2048K <6>[ 6.972743] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.122235] udevd[135]: starting version 3.2.9 <5>[ 7.127951] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.135095] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.141953] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.157435] udevd[135]: specified user 'tss' unknown <27>[ 7.162936] udevd[135]: specified group 'tss' unknown <30>[ 7.170872] udevd[136]: starting eudev-3.2.9 <6>[ 7.527431] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 7.538399] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.546659] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.564287] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.575715] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.591618] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.599581] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.627471] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.650902] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 7.656258] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 7.658946] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.667349] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 7.676633] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.682363] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.698755] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.720972] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.739368] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.748283] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.756119] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.822411] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 7.839332] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.847665] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 7.879799] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.883169] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.890390] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.897322] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 7.913503] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.921718] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.929068] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.936508] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.943389] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.975108] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.982499] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.988912] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.997052] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 8.005942] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.014508] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.023106] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.031680] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.049872] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.058047] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.080820] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.095133] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.103755] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.112452] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.121078] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.288738] caam algorithms registered in /proc/crypto <6>[ 8.295787] caam 2100000.crypto: registering rng-caam <4>[ 8.307909] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.315969] panel-simple panel-lcd: Specify missing connector_type done <4>[ 8.326246] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <6>[ 8.339739] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <5>[ 8.346967] random: dd: uninitialized urandom read (32 bytes read) <6>[ 8.348349] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) OK <6>[ 8.363276] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.372164] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.470765] random: dropbear: uninitialized urandom read (32 bytes read) OK <5>[ 8.483580] random: crng init done <5>[ 8.487590] random: 1 urandom warning(s) missed due to ratelimiting /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-14787056/environment / # /lava-14787056/bin/lava-test-runner /lava-14787056/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14787056/0/tests/0_dmesg + cat uuid + UUID=14787056_1.5.2.4.1<8>[ 9.108247] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.165296] <8>[ 9.215699] <8>[ 9.260794] + set +x <8>[ 9.272117] / #