Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'.  U-Boot SPL 2018.01-dirty (Jul 31 2024 - 16:15:46) Trying to boot from MMC2 U-Boot 2018.01-dirty (Jul 31 2024 - 16:15:46 +0200) CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 4 seconds U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.175.42 (12 ms) U-Boot> setenv serverip 192.168.32.2 setenv serverip 192.168.32.2 U-Boot> tftp 0x82000000 1219794/tftp-deploy-sypeh4yq/kernel/zImage tftp 0x82000000 1219794/tftp-deploy-sypeh4yq/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1219794/tftp-deploy-sypeh4yq/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 2.4 MiB/s done Bytes transferred = 4642608 (46d730 hex) U-Boot> tftp 0x83000000 1219794/tftp-deploy-sypeh4yq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1219794/tftp-deploy-sypeh4yq/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1219794/tftp-deploy-sypeh4yq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 3 MiB/s done Bytes transferred = 14141652 (d7c8d4 hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x88000000 1219794/tftp-deploy-sypeh4yq/dtb/am335x-boneblack.dtb tftp 0x88000000 1219794/tftp-deploy-sypeh4yq/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1219794/tftp-deploy-sypeh4yq/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 2 MiB/s done Bytes transferred = 62861 (f58d hex) U-Boot> setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-11-08 21:03:29 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14141588 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.226-cip53 (KernelCI@build-j369836-arm-gcc-12-omap2plus-defconfig-s6gw5) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Fri Nov 8 20:46:56 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] Memory: 471028K/522240K available (10240K kernel code, 1028K rwdata, 2176K rodata, 1024K init, 282K bss, 34828K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000012] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008344] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018564] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030202] Console: colour dummy device 80x30 <3>[ 0.035073] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042132] This ensures that you still see kernel messages. Please <3>[ 0.048857] update your kernel commandline. <6>[ 0.053458] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095540] CPU: Testing write buffer coherency: ok <6>[ 0.100921] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106386] pid_max: default: 32768 minimum: 301 <6>[ 0.111555] LSM: Security Framework initializing <6>[ 0.116655] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124467] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134141] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140636] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147836] rcu: Hierarchical SRCU implementation. <6>[ 0.153625] smp: Bringing up secondary CPUs ... <6>[ 0.158562] smp: Brought up 1 node, 1 CPU <6>[ 0.162988] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169717] CPU: All CPU(s) started in SVC mode. <6>[ 0.175458] devtmpfs: initialized <6>[ 0.191219] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199762] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210202] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218675] pinctrl core: initialized pinctrl subsystem <6>[ 0.226342] NET: Registered protocol family 16 <6>[ 0.233939] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260382] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266470] audit: initializing netlink subsys (disabled) <6>[ 0.273538] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273554] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280164] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.286883] cpuidle: using governor menu <5>[ 1.637727] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.823991] No ATAGs? <6>[ 1.826618] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.856529] Kprobes globally optimized <6>[ 1.869739] iommu: Default domain type: Translated <6>[ 1.876764] vgaarb: loaded <5>[ 1.880470] SCSI subsystem initialized <6>[ 1.885766] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.891249] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.900973] PTP clock support registered <6>[ 1.906547] clocksource: Switched to clocksource dmtimer <5>[ 2.537187] VFS: Disk quotas dquot_6.6.0 <6>[ 2.541604] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.558441] NET: Registered protocol family 2 <6>[ 2.563506] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.572205] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.581187] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.589487] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.597168] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.604088] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.611119] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.618744] NET: Registered protocol family 1 <6>[ 2.624502] RPC: Registered named UNIX socket transport module. <6>[ 2.630970] RPC: Registered udp transport module. <6>[ 2.636079] RPC: Registered tcp transport module. <6>[ 2.641206] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.648135] PCI: CLS 0 bytes, default 64 <6>[ 2.653154] Trying to unpack rootfs image as initramfs... <6>[ 3.615175] Freeing initrd memory: 13812K <6>[ 3.620892] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.631296] Initialise system trusted keyrings <6>[ 3.636709] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.644885] NFS: Registering the id_resolver key type <5>[ 3.650492] Key type id_resolver registered <5>[ 3.655065] Key type id_legacy registered <6>[ 3.659538] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.667560] Key type asymmetric registered <5>[ 3.672054] Asymmetric key parser 'x509' registered <6>[ 3.677410] io scheduler mq-deadline registered <6>[ 3.682341] io scheduler kyber registered <3>[ 3.888880] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.897567] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 4.057373] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 4.114922] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.217627] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.226253] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.310240] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.318926] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.341026] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.349706] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.436771] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.445227] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.473688] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.488318] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 4.499354] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.508781] printk: console [ttyS0] enabled <6>[ 4.508781] printk: console [ttyS0] enabled <6>[ 4.517852] printk: bootconsole [omap8250] disabled <6>[ 4.517852] printk: bootconsole [omap8250] disabled <6>[ 4.541815] brd: module loaded <6>[ 4.552616] loop: module loaded <3>[ 4.558264] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 4.626525] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.669638] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.679545] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.686199] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.692009] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.699567] cpsw 4a100000.ethernet: Detected MACID = 08:04:b4:96:48:24 <6>[ 4.708583] i2c /dev entries driver <5>[ 4.714060] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.722014] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.728556] sdhci: Copyright(c) Pierre Ossman <6>[ 4.733900] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.742233] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.752022] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.760511] Initializing XFRM netlink socket <6>[ 4.765314] NET: Registered protocol family 10 <6>[ 4.771768] Segment Routing with IPv6 <6>[ 4.775811] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.782897] NET: Registered protocol family 17 <6>[ 4.787752] NET: Registered protocol family 15 <5>[ 4.792591] Key type dns_resolver registered <6>[ 4.797784] oprofile: using arm/armv7 <6>[ 4.801832] ThumbEE CPU extension supported. <5>[ 4.806400] Registering SWP/SWPB emulation handler <3>[ 4.811948] omap_voltage_late_init: Voltage driver support not added <3>[ 4.818668] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.827084] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.835753] SmartReflex Class3 initialized <6>[ 4.840709] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.849623] Loading compiled-in X.509 certificates <6>[ 4.874539] OMAP GPIO hardware version 0.1 <4>[ 4.907222] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.920907] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.929512] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.935916] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.946051] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.957462] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.966559] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.971720] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.986253] mmc1: new high speed MMC card at address 0001 <6>[ 4.993115] mmcblk1: mmc1:0001 MK2704 3.53 GiB <6>[ 4.998686] mmcblk1boot0: mmc1:0001 MK2704 partition 1 2.00 MiB <6>[ 5.005332] mmcblk1boot1: mmc1:0001 MK2704 partition 2 2.00 MiB <6>[ 5.011932] mmcblk1rpmb: mmc1:0001 MK2704 partition 3 512 KiB, chardev (249:0) <6>[ 5.021464] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.030452] mmcblk1: p1 <6>[ 5.038770] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.128069] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.247227] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.276548] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.306638] Sending DHCP requests ., OK <6>[ 7.350630] IP-Config: Got DHCP answer from 192.168.175.254, my address is 192.168.175.42 <6>[ 7.359138] IP-Config: Complete: <6>[ 7.362650] device=eth0, hwaddr=08:04:b4:96:48:24, ipaddr=192.168.175.42, mask=255.255.255.0, gw=192.168.175.254 <6>[ 7.373607] host=beaglebone, domain=, nis-domain=(none) <6>[ 7.379578] bootserver=192.168.175.254, rootserver=192.168.175.254, rootpath= <6>[ 7.379586] nameserver0=192.168.175.254 <6>[ 7.392385] clk: Disabling unused clocks <6>[ 7.398732] Freeing unused kernel memory: 1024K <6>[ 7.417027] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.648478] udevd[100]: starting version 3.2.9 <5>[ 7.654710] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.662818] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.669932] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.687003] udevd[100]: specified user 'tss' unknown <27>[ 7.692585] udevd[100]: specified group 'tss' unknown <30>[ 7.703670] udevd[101]: starting eudev-3.2.9 <4>[ 8.334047] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 8.467330] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 8.474824] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 8.482461] at24 2-0054: supply vcc not found, using dummy regulator <3>[ 8.504967] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 8.522413] remoteproc remoteproc0: wkup_m3 is available <3>[ 8.537854] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 8.621216] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <6>[ 8.637272] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 8.684285] usbcore: registered new interface driver usbfs <6>[ 8.690323] usbcore: registered new interface driver hub <6>[ 8.696012] usbcore: registered new device driver usb <6>[ 8.707041] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 8.712463] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <6>[ 8.747248] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <4>[ 8.769689] at24 2-0055: supply vcc not found, using dummy regulator <3>[ 8.783748] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 8.825180] at24 2-0056: supply vcc not found, using dummy regulator <6>[ 8.890619] tda998x 0-0070: found TDA19988 <4>[ 8.908979] at24 2-0057: supply vcc not found, using dummy regulator <4>[ 9.060299] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <3>[ 9.071982] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 9.133443] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.203054] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <3>[ 9.320351] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 9.413717] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.419520] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.427879] remoteproc remoteproc0: powering up wkup_m3 <4>[ 9.433552] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 9.443432] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 9.449685] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 9.577336] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 9.584586] random: crng init done <6>[ 9.603103] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.611817] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.619383] usb usb1: Product: MUSB HDRC host driver <6>[ 9.624635] usb usb1: Manufacturer: Linux 5.10.226-cip53 musb-hcd <6>[ 9.631038] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.665243] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 9.697852] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 9.748105] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 9.757907] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 9.858436] hub 1-0:1.0: USB hub found <6>[ 9.908955] hub 1-0:1.0: 1 port detected <3>[ 9.989638] PM: Cannot get wkup_m3_ipc handle <6>[ 10.031279] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 10.051063] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 10.092520] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 10.109653] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 10.175498] PM: Cannot get wkup_m3_ipc handle <3>[ 10.192928] PM: Cannot get wkup_m3_ipc handle <3>[ 10.525652] PM: Cannot get wkup_m3_ipc handle <3>[ 10.557047] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1219794/environment . /lava-1219794/environment / # /lava-1219794/bin/lava-test-runner /lava-1219794/0 /lava-1219794/bin/lava-test-runner /lava-1219794/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1219794/0/tests/0_dmesg + cat uuid + UUID=1219794_1.5.2.4.1 <8>[ 11.631031] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.697263] <8>[ 11.757621] <8>[ 11.817713] + set +x <8>[ 11.829184] / #