[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10591300/tftp-deploy-swuwp4wm/kernel/zImage tftp 0x10000000 10591300/tftp-deploy-swuwp4wm/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10591300/tftp-deploy-swuwp4wm/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 11.4 MiB/s done Bytes transferred = 10347008 (9de200 hex) => tftp 0x14000000 10591300/tftp-deploy-swuwp4wm/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10591300/tftp-deploy-swuwp4wm/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10591300/tftp-deploy-swuwp4wm/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 11.4 MiB/s done Bytes transferred = 17163118 (105e36e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10591300/tftp-deploy-swuwp4wm/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10591300/tftp-deploy-swuwp4wm/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10591300/tftp-deploy-swuwp4wm/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9de200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17163054 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.31 (KernelCI@build-j1609173-arm-gcc-10-multi-v7-defconfig-569zr) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Jun 5 11:08:09 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 930388K/1048576K available (14336K kernel code, 2468K rwdata, 6004K rodata, 2048K init, 429K bss, 52652K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022384] Console: colour dummy device 80x30 <6>[ 0.024288] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034693] pid_max: default: 32768 minimum: 301 <6>[ 0.039744] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047146] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055753] CPU: Testing write buffer coherency: ok <6>[ 0.060259] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065879] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072374] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079913] rcu: Hierarchical SRCU implementation. <6>[ 0.083312] rcu: Max phase no-delay instances is 1000. <6>[ 0.092434] EFI services will not be available. <6>[ 0.094737] smp: Bringing up secondary CPUs ... <6>[ 0.100004] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.100020] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.111315] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111331] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.122517] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122533] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.132933] smp: Brought up 1 node, 4 CPUs <6>[ 0.137198] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.143615] CPU: All CPU(s) started in SVC mode. <6>[ 0.149089] devtmpfs: initialized <6>[ 0.159625] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.164923] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.174850] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.185248] pinctrl core: initialized pinctrl subsystem <6>[ 0.191558] DMI not present or invalid. <6>[ 0.193614] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.202479] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.209437] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.209503] cpuidle: using governor menu <6>[ 0.217468] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.231042] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.236075] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.265700] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 <6>[ 0.282407] platform 2400000.ipu: Fixed dependency cycle(s) with /disp0 <6>[ 0.286957] platform disp0: Fixed dependency cycle(s) with /panel-lcd <6>[ 0.293625] platform ldb: Fixed dependency cycle(s) with /panel-lvds0 <6>[ 0.301324] No ATAGs? <6>[ 0.302532] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.310651] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.320017] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.331651] Serial: AMBA PL011 UART driver <6>[ 0.336000] printk: console [ramoops-1] enabled <6>[ 0.338172] pstore: Registered ramoops as persistent store backend <6>[ 0.344383] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.382407] iommu: Default domain type: Translated <6>[ 0.384709] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.392072] SCSI subsystem initialized <6>[ 0.395835] usbcore: registered new interface driver usbfs <6>[ 0.401016] usbcore: registered new interface driver hub <6>[ 0.406613] usbcore: registered new device driver usb <4>[ 0.412086] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.419917] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.428364] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.436288] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.446551] i2c i2c-0: IMX I2C adapter registered <6>[ 0.450886] i2c i2c-1: IMX I2C adapter registered <6>[ 0.455399] i2c i2c-2: IMX I2C adapter registered <6>[ 0.460893] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.464658] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.474090] PTP clock support registered <6>[ 0.478490] EDAC MC: Ver: 3.0.0 <6>[ 0.485464] vgaarb: loaded <6>[ 1.587641] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.601045] NET: Registered PF_INET protocol family <6>[ 1.603906] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.613180] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 1.619711] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.627723] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.635717] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 1.643467] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.650018] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.656638] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.664181] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.670502] RPC: Registered named UNIX socket transport module. <6>[ 1.675999] RPC: Registered udp transport module. <6>[ 1.680985] RPC: Registered tcp transport module. <6>[ 1.685913] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.692635] PCI: CLS 0 bytes, default 64 <6>[ 1.697329] Trying to unpack rootfs image as initramfs... <4>[ 1.697455] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 1.710739] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.720780] Initialise system trusted keyrings <6>[ 1.723739] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.736190] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.740389] NFS: Registering the id_resolver key type <5>[ 1.744800] Key type id_resolver registered <5>[ 1.749257] Key type id_legacy registered <6>[ 1.753611] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.760458] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.768161] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.773379] Key type asymmetric registered <5>[ 1.777040] Asymmetric key parser 'x509' registered <6>[ 1.782476] bounce: pool size: 64 pages <6>[ 1.786396] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.793977] io scheduler mq-deadline registered <6>[ 1.798716] io scheduler kyber registered <6>[ 1.854538] mxs-dma 110000.dma-apbh: initialized <6>[ 1.940019] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.949178] SuperH (H)SCI(F) driver initialized <6>[ 1.952265] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX <6>[ 1.961254] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 270, base_baud = 5000000) is a IMX <6>[ 1.969136] printk: console [ttymxc1] enabled <6>[ 1.969136] printk: console [ttymxc1] enabled <6>[ 1.978298] printk: bootconsole [ec_imx21] disabled <6>[ 1.978298] printk: bootconsole [ec_imx21] disabled <6>[ 1.990157] msm_serial: driver initialized <6>[ 1.995733] STMicroelectronics ASC driver initialized <6>[ 2.003037] STM32 USART driver initialized <6>[ 2.029956] brd: module loaded <6>[ 2.041054] loop: module loaded <6>[ 2.048686] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.056902] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.065226] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.073707] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 2.081771] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 2.089603] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 2.097185] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 2.107947] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.115221] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.124337] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.135785] scsi host0: ahci-imx <6>[ 2.139721] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 2.161742] CAN device driver interface <6>[ 2.167821] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.177913] pps pps0: new PPS source ptp0 <3>[ 2.185262] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 2.192735] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 2.200093] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 2.207418] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 2.214770] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 2.222119] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 2.229468] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 2.236794] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 2.244146] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 7 <6>[ 2.489289] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.495044] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.501656] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.154634] Freeing initrd memory: 16764K <4>[ 3.159230] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.169953] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.197956] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.205573] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.210838] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.217091] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.222786] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.235466] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 3.241392] usbcore: registered new interface driver pegasus <6>[ 3.247371] usbcore: registered new interface driver asix <6>[ 3.253098] usbcore: registered new interface driver ax88179_178a <6>[ 3.259522] usbcore: registered new interface driver cdc_ether <6>[ 3.265671] usbcore: registered new interface driver smsc75xx <6>[ 3.271753] usbcore: registered new interface driver smsc95xx <6>[ 3.277833] usbcore: registered new interface driver net1080 <6>[ 3.283803] usbcore: registered new interface driver cdc_subset <6>[ 3.290045] usbcore: registered new interface driver zaurus <6>[ 3.295955] usbcore: registered new interface driver cdc_ncm <6>[ 3.308676] usbcore: registered new interface driver usb-storage <6>[ 3.323741] i2c_dev: i2c /dev entries driver <6>[ 3.352567] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.359048] sdhci: Copyright(c) Pierre Ossman <6>[ 3.366698] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.375635] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.383077] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.383477] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.388376] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.399111] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.407450] usbcore: registered new interface driver usbhid <6>[ 3.413348] usbhid: USB HID core driver <6>[ 3.427703] NET: Registered PF_INET6 protocol family <6>[ 3.430794] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.434364] Segment Routing with IPv6 <6>[ 3.444125] In-situ OAM (IOAM) with IPv6 <6>[ 3.448436] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.455247] NET: Registered PF_PACKET protocol family <6>[ 3.460614] can: controller area network core <6>[ 3.464805] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.465309] NET: Registered PF_CAN protocol family <6>[ 3.477488] can: raw protocol <6>[ 3.480747] can: broadcast manager protocol <6>[ 3.485208] can: netlink gateway - max_hops=1 <5>[ 3.490241] Key type dns_resolver registered <6>[ 3.496953] ThumbEE CPU extension supported. <5>[ 3.501554] Registering SWP/SWPB emulation handler <5>[ 3.507908] Loading compiled-in X.509 certificates <6>[ 3.518847] pstore: Using crash dump compression: deflate <4>[ 3.555684] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.565908] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.571120] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.579368] mmc2: new high speed SDHC card at address 59b4 <6>[ 3.586134] mmcblk2: mmc2:59b4 SD 14.7 GiB <4>[ 3.597940] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.605617] GPT:29296874 != 30863359 <4>[ 3.609509] GPT:Alternate GPT header not at the end of the disk. <6>[ 3.609526] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <4>[ 3.615778] GPT:29296874 != 30863359 <4>[ 3.625308] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.628042] hub 1-0:1.0: USB hub found <6>[ 3.630801] mmcblk2: p1 p2 p3 <6>[ 3.634753] hub 1-0:1.0: 1 port detected <6>[ 3.644890] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 3.663211] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 3.679199] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.927698] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.129312] hub 1-1:1.0: USB hub found <6>[ 4.133547] hub 1-1:1.0: 3 ports detected <6>[ 6.798108] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.805943] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.837726] Sending DHCP requests ., OK <6>[ 6.881876] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 6.890232] IP-Config: Complete: <6>[ 6.893744] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.904526] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 6.912679] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.912700] nameserver0=192.168.201.1 <6>[ 6.931716] Freeing unused kernel image (initmem) memory: 2048K <6>[ 6.968791] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.117500] udevd[127]: starting version 3.2.9 <5>[ 12.277626] random: crng init done <27>[ 12.288713] udevd[127]: specified user 'tss' unknown <27>[ 12.294144] udevd[127]: specified group 'tss' unknown <30>[ 12.301951] udevd[128]: starting eudev-3.2.9 <6>[ 12.654178] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 12.711640] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 12.902364] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 12.958320] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 12.984839] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 13.007708] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 13.014652] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 13.057951] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 13.096735] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 13.103186] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 13.116990] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 13.160280] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 13.298684] caam 2100000.crypto: Entropy delay = 3200 <6>[ 13.364836] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 13.425599] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 13.431095] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 13.438023] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 13.482666] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 13.493179] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <3>[ 13.580455] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 13.801924] caam algorithms registered in /proc/crypto <6>[ 13.808972] caam 2100000.crypto: registering rng-caam <6>[ 13.814601] caam 2100000.crypto: rng crypto API alg registered prng-caam done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10591300/environment . /lava-10591300/environment / # /lava-10591300/bin/lava-test-runner /lava-10591300/0 /lava-10591300/bin/lava-test-runner /lava-10591300/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10591300/0/tests/0_dmesg + cat uuid <8>[ 14.572395] + UUID=10591300_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.619123] <8>[ 14.662143] <8>[ 14.705310] + set<8>[ 14.715259] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10591300/environment / # . /lava-10591300/environment/lava-10591300/bin/lava-test-runner /lava-10591300/1 / # /lava-10591300/bin/lava-test-runner /lava-10591300/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10591300/1/tests/1_bootrr + cat uuid + <8>[ 15.230072] UUID=10591300_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10591300/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd platform: supplier 2080000.pwm not ready backlight-lvds platform: supplier 208c000.pwm not ready panel-lcd platform: supplier backlight-lcd not ready ldb disp0 panel-lvds0 platform: supplier backlight-lvds not ready /lava-10591300/1/../bin/lava-test-case <8>[ 16.306053] /lava-10591300/1/../bin/lava-test-case <8>[ 16.348617] /lava-10591300/1/../bin/lava-test-case <8>[ 16.374983] + set<8>[ 16.394856] +x / #