[Enter `^Ec?' for help] U-Boot SPL 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45) U-Boot 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45 +0000) Model: Radxa Rock 2 Square DRAM: 2 GiB MMC: dwmmc@ff0c0000: 0, dwmmc@ff0f0000: 1 In: serial@ff690000 Out: serial@ff690000 Err: serial@ff690000 Incorrect eeprom header Net: eth0: ethernet@ff290000 Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@ff290000 Waiting for PHY auto negotiation to complete...... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.201.22 (757 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x2000000 12703910/tftp-deploy-qvzpve_r/kernel/zImage tftp 0x2000000 12703910/tftp-deploy-qvzpve_r/kernel/zImage Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12703910/tftp-deploy-qvzpve_r/kernel/zImage'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 3.6 MiB/s done Bytes transferred = 10519040 (a08200 hex) => tftp 0x4000000 12703910/tftp-deploy-qvzpve_r/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4000000 12703910/tftp-deploy-qvzpve_r/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12703910/tftp-deploy-qvzpve_r/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 3.6 MiB/s done Bytes transferred = 17157154 (105cc22 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1f00000 12703910/tftp-deploy-qvzpve_r/dtb/rk3288-rock2-square.dtb tftp 0x1f00000 12703910/tftp-deploy-qvzpve_r/dtb/rk3288-rock2-square.dtb Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12703910/tftp-deploy-qvzpve_r/dtb/rk3288-rock2-square.dtb'. Load address: 0x1f00000 Loading: *### 3.3 MiB/s done Bytes transferred = 41716 (a2f4 hex) => setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x2000000 0x4000000 0x1f00000 bootz 0x2000000 0x4000000 0x1f00000 Kernel image @ 0x2000000 [ 0x000000 - 0xa08200 ] ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17157090 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Using Device Tree in place at 01f00000, end 01f0d2f3 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 6.1.75-cip14 (KernelCI@build-j98687-arm-gcc-10-multi-v7-defconfig-cfg4z) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Feb 5 13:21:58 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Radxa Rock 2 Square [ 0.000000] earlycon: uart0 at MMIO32 0xff690000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1970772K/2097152K available (14336K kernel code, 2469K rwdata, 6208K rodata, 2048K init, 428K bss, 60844K reserved, 65536K cma-reserved, 1245184K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009082] Switching to timer-based delay loop, resolution 41ns <6>[ 0.023628] Console: colour dummy device 80x30 <6>[ 0.028844] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.040519] CPU: Testing write buffer coherency: ok <6>[ 0.046196] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.052042] pid_max: default: 32768 minimum: 301 <6>[ 0.057570] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.065911] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.075654] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 <6>[ 0.083278] Setting up static identity map for 0x300000 - 0x3000ac <6>[ 0.092475] rcu: Hierarchical SRCU implementation. <6>[ 0.098022] rcu: Max phase no-delay instances is 1000. <6>[ 0.109124] EFI services will not be available. <6>[ 0.114753] smp: Bringing up secondary CPUs ... <6>[ 0.121831] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 <6>[ 0.121851] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.136156] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 <6>[ 0.136175] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.150422] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 <6>[ 0.150442] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.162901] smp: Brought up 1 node, 4 CPUs <6>[ 0.167716] SMP: Total of 4 processors activated (192.00 BogoMIPS). <6>[ 0.174885] CPU: All CPU(s) started in SVC mode. <6>[ 0.180886] devtmpfs: initialized <6>[ 0.194491] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 <6>[ 0.203454] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214572] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.224380] pinctrl core: initialized pinctrl subsystem <6>[ 0.234428] DMI not present or invalid. <6>[ 0.239771] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.248923] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.259824] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.259893] cpuidle: using governor menu <6>[ 0.272053] No ATAGs? <6>[ 0.274970] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.284075] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.294351] Serial: AMBA PL011 UART driver <6>[ 0.323340] platform ff980000.hdmi: Fixed dependency cycle(s) with /vop@ff940000/port/endpoint@0 <6>[ 0.333324] platform ff980000.hdmi: Fixed dependency cycle(s) with /vop@ff930000/port/endpoint@0 <6>[ 0.358888] rockchip-gpio ff750000.gpio: probed /pinctrl/gpio@ff750000 <6>[ 0.367122] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000 <6>[ 0.375296] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000 <6>[ 0.383500] rockchip-gpio ff7a0000.gpio: probed /pinctrl/gpio@ff7a0000 <6>[ 0.391762] rockchip-gpio ff7b0000.gpio: probed /pinctrl/gpio@ff7b0000 <6>[ 0.399955] rockchip-gpio ff7c0000.gpio: probed /pinctrl/gpio@ff7c0000 <6>[ 0.408132] rockchip-gpio ff7d0000.gpio: probed /pinctrl/gpio@ff7d0000 <6>[ 0.416348] rockchip-gpio ff7e0000.gpio: probed /pinctrl/gpio@ff7e0000 <6>[ 0.424513] rockchip-gpio ff7f0000.gpio: probed /pinctrl/gpio@ff7f0000 <6>[ 0.464197] iommu: Default domain type: Translated <6>[ 0.469845] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.477926] SCSI subsystem initialized <6>[ 0.482852] usbcore: registered new interface driver usbfs <6>[ 0.489262] usbcore: registered new interface driver hub <6>[ 0.495424] usbcore: registered new device driver usb <6>[ 0.503937] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.509675] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.520025] PTP clock support registered <6>[ 0.524884] EDAC MC: Ver: 3.0.0 <6>[ 0.532387] vgaarb: loaded <6>[ 0.540697] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.560496] NET: Registered PF_INET protocol family <6>[ 0.566419] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.577198] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.586702] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.595516] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.604392] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.612997] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.620348] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.627962] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.636193] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.643346] RPC: Registered named UNIX socket transport module. <6>[ 0.650135] RPC: Registered udp transport module. <6>[ 0.655610] RPC: Registered tcp transport module. <6>[ 0.661073] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.668432] PCI: CLS 0 bytes, default 64 <6>[ 0.674332] Trying to unpack rootfs image as initramfs... <6>[ 0.684372] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available <5>[ 0.695532] Initialise system trusted keyrings <6>[ 0.701129] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.715595] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.723105] NFS: Registering the id_resolver key type <5>[ 0.728979] Key type id_resolver registered <5>[ 0.733891] Key type id_legacy registered <6>[ 0.738701] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.746382] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.754842] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.760487] Key type asymmetric registered <5>[ 0.765302] Asymmetric key parser 'x509' registered <6>[ 0.771150] bounce: pool size: 64 pages <6>[ 0.775769] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 0.784199] io scheduler mq-deadline registered <6>[ 0.789460] io scheduler kyber registered <6>[ 0.867633] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 0.876286] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 <6>[ 0.901317] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 0.909927] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 <6>[ 1.008912] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.019615] printk: console [ttyS2] disabled <6>[ 1.024692] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 47, base_baud = 1500000) is a 16550A <6>[ 1.034906] printk: console [ttyS2] enabled <6>[ 1.034906] printk: console [ttyS2] enabled <6>[ 1.044891] printk: bootconsole [uart0] disabled <6>[ 1.044891] printk: bootconsole [uart0] disabled <6>[ 1.059570] SuperH (H)SCI(F) driver initialized <6>[ 1.066718] msm_serial: driver initialized <6>[ 1.071615] STMicroelectronics ASC driver initialized <6>[ 1.079497] STM32 USART driver initialized <6>[ 1.110627] brd: module loaded <6>[ 1.121392] loop: module loaded <6>[ 1.143650] CAN device driver interface <6>[ 1.150326] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.159024] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.164888] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.171902] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.178235] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.192895] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.199479] usbcore: registered new interface driver pegasus <6>[ 1.206183] usbcore: registered new interface driver asix <6>[ 1.212599] usbcore: registered new interface driver ax88179_178a <6>[ 1.219752] usbcore: registered new interface driver cdc_ether <6>[ 1.226658] usbcore: registered new interface driver smsc75xx <6>[ 1.233479] usbcore: registered new interface driver smsc95xx <6>[ 1.240248] usbcore: registered new interface driver net1080 <6>[ 1.246948] usbcore: registered new interface driver cdc_subset <6>[ 1.253940] usbcore: registered new interface driver zaurus <6>[ 1.260554] usbcore: registered new interface driver cdc_ncm <4>[ 1.270700] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.279140] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.360187] dwc2 ff540000.usb: DWC OTG Controller <6>[ 1.365807] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1 <6>[ 1.374034] dwc2 ff540000.usb: irq 51, io mem 0xff540000 <6>[ 1.381213] hub 1-0:1.0: USB hub found <6>[ 1.385751] hub 1-0:1.0: 1 port detected <4>[ 1.391273] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.399715] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.540797] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM <6>[ 1.567186] dwc2 ff580000.usb: DWC OTG Controller <6>[ 1.572803] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.581032] dwc2 ff580000.usb: irq 52, io mem 0xff580000 <6>[ 1.588093] hub 2-0:1.0: USB hub found <6>[ 1.592655] hub 2-0:1.0: 1 port detected <6>[ 1.600008] ehci-platform ff500000.usb: EHCI Host Controller <6>[ 1.603051] usbcore: registered new interface driver usb-storage <6>[ 1.606695] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3 <6>[ 1.622654] i2c_dev: i2c /dev entries driver <6>[ 1.632209] i2c 0-005a: Fixed dependency cycle(s) with /i2c@ff650000/act8846@5a/regulators/REG4 <6>[ 1.642376] i2c 0-005a: Fixed dependency cycle(s) with /i2c@ff650000/act8846@5a/regulators/REG2 <6>[ 1.656912] VDD_LOG: Bringing 1100000uV into 1000000-1000000uV <6>[ 1.675018] ehci-platform ff500000.usb: irq 53, io mem 0xff500000 <6>[ 1.690375] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! <6>[ 1.703082] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! <6>[ 1.710762] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 <6>[ 1.719255] hub 3-0:1.0: USB hub found <6>[ 1.723833] hub 3-0:1.0: 1 port detected <4>[ 1.736612] dw_wdt ff800000.watchdog: No valid TOPs array specified <6>[ 1.755058] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 500000 KHz, changing to: 600000 KHz <6>[ 1.770499] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.777735] sdhci: Copyright(c) Pierre Ossman <6>[ 1.785770] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.794185] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 1.795219] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.811102] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 1.818797] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 1.825356] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 1.837770] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.845697] usbcore: registered new interface driver usbhid <6>[ 1.852230] usbhid: USB HID core driver <6>[ 1.860275] NET: Registered PF_INET6 protocol family <6>[ 1.866658] Segment Routing with IPv6 <6>[ 1.871088] In-situ OAM (IOAM) with IPv6 <6>[ 1.875811] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.883062] NET: Registered PF_PACKET protocol family <6>[ 1.888997] can: controller area network core <6>[ 1.894238] NET: Registered PF_CAN protocol family <6>[ 1.899900] can: raw protocol <6>[ 1.903520] can: broadcast manager protocol <6>[ 1.908488] can: netlink gateway - max_hops=1 <5>[ 1.913862] Key type dns_resolver registered <6>[ 1.918979] ThumbEE CPU extension supported. <5>[ 1.924058] Registering SWP/SWPB emulation handler <5>[ 1.930058] Loading compiled-in X.509 certificates <6>[ 1.956797] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 1.964079] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 1.965382] Freeing initrd memory: 16756K <6>[ 1.971661] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). <6>[ 1.984032] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). <6>[ 1.990645] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). <6>[ 1.997269] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no). <6>[ 2.004487] rk_gmac-dwmac ff290000.ethernet: clock input from PHY <6>[ 2.016601] rk_gmac-dwmac ff290000.ethernet: init for RGMII <6>[ 2.023167] usb 3-1: new high-speed USB device number 2 using ehci-platform <6>[ 2.031265] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35 <6>[ 2.039546] rk_gmac-dwmac ff290000.ethernet: DWMAC1000 <6>[ 2.045680] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported <6>[ 2.054336] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported <6>[ 2.062991] rk_gmac-dwmac ff290000.ethernet: COE Type 2 <6>[ 2.069118] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported <6>[ 2.077288] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported <6>[ 2.084812] rk_gmac-dwmac ff290000.ethernet: Normal descriptors <6>[ 2.091722] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled <6>[ 2.098526] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 2.232744] hub 3-1:1.0: USB hub found <6>[ 2.237549] hub 3-1:1.0: 4 ports detected <6>[ 2.246354] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL) <6>[ 2.257941] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL) <6>[ 2.273848] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.275187] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.276393] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.276709] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 2.306208] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.313904] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.320428] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.331527] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller. <6>[ 2.335185] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.339211] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a <6>[ 2.353927] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 62,32 bit host data width,256 deep fifo <6>[ 2.365086] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller. <6>[ 2.372782] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a <6>[ 2.379132] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 2.379313] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 63,32 bit host data width,256 deep fifo <6>[ 2.400979] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.408678] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.408831] dwmmc_rockchip ff0f0000.mmc: allocated mmc-pwrseq <6>[ 2.415222] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.421912] mmc_host mmc1: card is non-removable. <6>[ 2.437322] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.446658] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.450709] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 2.454352] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.471458] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.486239] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.486381] rk_gmac-dwmac ff290000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 <6>[ 2.504122] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.505125] rk_gmac-dwmac ff290000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL) <6>[ 2.511818] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.530099] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.530689] rk_gmac-dwmac ff290000.ethernet eth0: No Safety Features support found <6>[ 2.549842] rk_gmac-dwmac ff290000.ethernet eth0: PTP not supported by HW <6>[ 2.557916] rk_gmac-dwmac ff290000.ethernet eth0: configuring for phy/rgmii link mode <6>[ 2.606324] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 2.619140] mmc1: new high speed MMC card at address 0001 <6>[ 2.628713] mmcblk1: mmc1:0001 032GE4 29.1 GiB <6>[ 2.643793] mmcblk1: p1 p2 <6>[ 2.647862] mmcblk1boot0: mmc1:0001 032GE4 4.00 MiB <6>[ 2.654590] mmcblk1boot1: mmc1:0001 032GE4 4.00 MiB <6>[ 2.661173] mmcblk1rpmb: mmc1:0001 032GE4 4.00 MiB, chardev (236:0) <6>[ 2.671203] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.679461] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.687158] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.693690] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 5.712092] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 5.722055] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.770689] Sending DHCP requests .., OK <6>[ 8.215642] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.22 <6>[ 8.225114] IP-Config: Complete: <6>[ 8.229051] device=eth0, hwaddr=4a:01:9c:e5:04:ff, ipaddr=192.168.201.22, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.241168] host=rk3288-rock2-square-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 8.250174] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.250218] nameserver0=192.168.201.1 <4>[ 8.267134] dw-apb-uart ff690000.serial: forbid DMA for kernel console <6>[ 8.288669] Freeing unused kernel image (initmem) memory: 2048K <6>[ 8.310822] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.387300] udevd[114]: starting version 3.2.9 <5>[ 8.393379] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.401287] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.409056] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.419972] udevd[114]: specified user 'tss' unknown <27>[ 8.426184] udevd[114]: specified group 'tss' unknown <30>[ 8.433158] udevd[115]: starting eudev-3.2.9 <6>[ 8.630941] rockchip-vop ff930000.vop: Adding to iommu group 0 <6>[ 8.638115] rockchip-vop ff940000.vop: Adding to iommu group 1 <6>[ 8.661286] rockchip-drm display-subsystem: bound ff930000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 8.670171] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 8.679671] rockchip-drm display-subsystem: bound ff940000.vop (ops vop_component_ops [rockchipdrm]) <4>[ 8.690611] dwhdmi-rockchip ff980000.hdmi: supply avdd-0v9 not found, using dummy regulator <4>[ 8.700349] dwhdmi-rockchip ff980000.hdmi: supply avdd-1v8 not found, using dummy regulator <6>[ 8.710114] dwhdmi-rockchip ff980000.hdmi: Detected HDMI TX controller v2.00a with HDCP (DWC MHL PHY) <6>[ 8.716745] usbcore: registered new device driver onboard-usb-hub <6>[ 8.730542] rockchip-drm display-subsystem: bound ff980000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm]) <6>[ 8.730743] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 8.743844] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0 <6>[ 8.749171] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 8.749190] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 8.758374] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 8.784458] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 8.785467] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 8.792946] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 8.812356] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <4>[ 8.814762] rtc-hym8563 0-0051: no valid clock/calendar values available <6>[ 8.820051] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 8.834376] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 8.838608] rtc-hym8563 0-0051: registered as rtc0 <6>[ 8.849627] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <4>[ 8.865545] rtc-hym8563 0-0051: no valid clock/calendar values available <6>[ 8.869935] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <3>[ 8.873360] rtc-hym8563 0-0051: hctosys: unable to read the hardware clock <6>[ 8.889060] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 8.895626] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 8.914642] dwmmc_rockchip ff0d0000.mmc: allocated mmc-pwrseq <6>[ 8.921387] mmc_host mmc2: card is non-removable. <6>[ 8.942796] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 8.976027] panfrost ffa30000.gpu: clock rate = 400000000 <6>[ 8.994981] panfrost ffa30000.gpu: mali-t760 id 0x750 major 0x0 minor 0x0 status 0x1 <6>[ 8.996901] rk3288-crypto ff8a0000.crypto: will run requests pump with realtime priority <6>[ 9.003969] panfrost ffa30000.gpu: features: 00000000,00000407, issues: 00000000,24040400 <6>[ 9.022746] panfrost ffa30000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 <6>[ 9.030733] usb 3-1: reset high-speed USB device number 2 using ehci-platform <6>[ 9.036265] panfrost ffa30000.gpu: shader_present=0xf l2_present=0x1 <6>[ 9.061721] rk3288-crypto ff8a0000.crypto: Crypto Accelerator successfully registered <6>[ 9.063222] [drm] Initialized panfrost 1.2.0 20180908 for ffa30000.gpu on minor 1 <6>[ 9.065875] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) <6>[ 9.067248] mmc2: new high speed SDIO card at address 0001 <5>[ 9.226539] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 9.271728] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>[ 9.281144] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 9.290565] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 9.300510] cfg80211: failed to load regulatory.db <6>[ 9.312860] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 9.322904] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.radxa,rock2-square.bin failed with error -2 <4>[ 9.335897] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <6>[ 9.512289] hub 3-1:1.0: USB hub found <6>[ 9.517329] hub 3-1:1.0: 4 ports detected <6>[ 9.527213] hub 3-1:1.0: USB hub found <6>[ 9.532091] hub 3-1:1.0: 4 ports detected done Saving random seed: <5>[ 9.561335] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <3>[ 10.351594] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 <5>[ 22.360679] random: crng init done <5>[ 22.364771] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12703910/environment . /lava-12703910/environment / # /lava-12703910/bin/lava-test-runner /lava-12703910/0 /lava-12703910/bin/lava-test-runner /lava-12703910/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12703910/0/tests/0_dmesg + cat uuid <8>[ 22.945641] + UUID=12703910_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.974067] <8>[ 22.998984] <8>[ 23.027284] + set +x <8>[ 23.037607] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12703910/environment / # . /lava-12703910/environment/lava-12703910/bin/lava-test-runner /lava-12703910/1 / # /lava-12703910/bin/lava-test-runner /lava-12703910/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12703910/1/tests/1_boot<8>[ 23.511239] rr + cat uuid + UUID=12703910_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12703910/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-12703910/1/../bin/lava-test-case <8>[ 23.552760] /lava-12703910/1/../bin/lava-test-case <8>[ 23.575124] /lava-12703910/1/../bin/lava-test-case <8>[ 23.592176] /lava-12703910/1/../bin/lava-test-case <8>[ 23.618719] /lava-12703910/1/../bin/lava-test-case <8>[ 23.645764] /lava-12703910/1/../bin/lava-test-case <8>[ 23.670271] /lava-12703910/1/../bin/lava-test-case <8>[ 23.697708] /lava-12703910/1/../bin/lava-test-case <8>[ 23.717538] /lava-12703910/1/../bin/lava-test-case <8>[ 23.740044] + set +x <8>[ 23.748854] / #