[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (10 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12925696/tftp-deploy-0fs6jlo0/kernel/zImage tftp 0x10000000 12925696/tftp-deploy-0fs6jlo0/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12925696/tftp-deploy-0fs6jlo0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 14.1 MiB/s done Bytes transferred = 10523136 (a09200 hex) => tftp 0x14000000 12925696/tftp-deploy-0fs6jlo0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12925696/tftp-deploy-0fs6jlo0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12925696/tftp-deploy-0fs6jlo0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 14.2 MiB/s done Bytes transferred = 13238161 (c9ff91 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12925696/tftp-deploy-0fs6jlo0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12925696/tftp-deploy-0fs6jlo0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12925696/tftp-deploy-0fs6jlo0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.1 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12925696/extract-nfsrootfs-qs2ojslk,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12925696/extract-nfsrootfs-qs2ojslk,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xa09200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13238097 Bytes = 12.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.80-cip16 (KernelCI@build-j128895-arm-gcc-10-multi-v7-defconfig-cd5ls) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun Mar 3 10:56:33 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12925696/extract-nfsrootfs-qs2ojslk,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 934224K/1048576K available (14336K kernel code, 2469K rwdata, 6208K rodata, 2048K init, 428K bss, 48816K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022431] Console: colour dummy device 80x30 <6>[ 0.024343] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034737] CPU: Testing write buffer coherency: ok <6>[ 0.039868] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.045166] pid_max: default: 32768 minimum: 301 <6>[ 0.050217] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057631] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066540] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072410] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079963] rcu: Hierarchical SRCU implementation. <6>[ 0.083357] rcu: Max phase no-delay instances is 1000. <6>[ 0.092426] EFI services will not be available. <6>[ 0.094732] smp: Bringing up secondary CPUs ... <6>[ 0.099995] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.100012] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.111303] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111318] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.122508] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122524] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.132922] smp: Brought up 1 node, 4 CPUs <6>[ 0.137190] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.143607] CPU: All CPU(s) started in SVC mode. <6>[ 0.149079] devtmpfs: initialized <6>[ 0.160202] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.165505] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.175427] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.185886] pinctrl core: initialized pinctrl subsystem <6>[ 0.192196] DMI not present or invalid. <6>[ 0.194276] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.203190] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.210156] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.210220] cpuidle: using governor menu <6>[ 0.218213] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.230309] platform soc: Fixed dependency cycle(s) with /soc/bus@2000000/gpc@20dc000 <6>[ 0.250677] platform 20dc000.gpc: Fixed dependency cycle(s) with /soc/bus@2000000/clock-controller@20c4000 <6>[ 0.259214] platform 20e0000.pinctrl: Fixed dependency cycle(s) with /soc/bus@2000000/pinctrl@20e0000/imx6q-sabrelite/hoggrp <6>[ 0.284992] No ATAGs? <6>[ 0.285179] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.292960] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.302350] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.315362] Serial: AMBA PL011 UART driver <6>[ 0.319801] printk: console [ramoops-1] enabled <6>[ 0.321993] pstore: Registered ramoops as persistent store backend <6>[ 0.328223] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.366312] iommu: Default domain type: Translated <6>[ 0.368615] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.375974] SCSI subsystem initialized <6>[ 0.379660] usbcore: registered new interface driver usbfs <6>[ 0.384925] usbcore: registered new interface driver hub <6>[ 0.390532] usbcore: registered new device driver usb <4>[ 0.396070] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.403805] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.412275] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.420177] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.430477] i2c i2c-0: IMX I2C adapter registered <6>[ 0.434676] i2c i2c-1: IMX I2C adapter registered <6>[ 0.439247] i2c i2c-2: IMX I2C adapter registered <6>[ 0.444775] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.448585] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.457992] PTP clock support registered <6>[ 0.462393] EDAC MC: Ver: 3.0.0 <6>[ 0.469364] vgaarb: loaded <6>[ 0.475312] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.488059] NET: Registered PF_INET protocol family <6>[ 0.490770] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.499921] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.506665] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.514644] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.522726] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.530418] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.536940] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.543635] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.551121] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.557453] RPC: Registered named UNIX socket transport module. <6>[ 0.563003] RPC: Registered udp transport module. <6>[ 0.567988] RPC: Registered tcp transport module. <6>[ 0.572918] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.579638] PCI: CLS 0 bytes, default 64 <4>[ 0.584443] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 0.584536] Trying to unpack rootfs image as initramfs... <6>[ 0.603381] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 0.610916] Initialise system trusted keyrings <6>[ 0.613901] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.626342] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.630451] NFS: Registering the id_resolver key type <5>[ 0.634947] Key type id_resolver registered <5>[ 0.639391] Key type id_legacy registered <6>[ 0.643734] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.650616] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.658307] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.663437] Key type asymmetric registered <5>[ 0.667211] Asymmetric key parser 'x509' registered <6>[ 0.672499] bounce: pool size: 64 pages <6>[ 0.676556] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.684068] io scheduler mq-deadline registered <6>[ 0.688883] io scheduler kyber registered <6>[ 0.757916] mxs-dma 110000.dma-apbh: initialized <6>[ 0.836880] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.845914] SuperH (H)SCI(F) driver initialized <6>[ 0.848989] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX <6>[ 0.857957] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 270, base_baud = 5000000) is a IMX <6>[ 0.865869] printk: console [ttymxc1] enabled <6>[ 0.865869] printk: console [ttymxc1] enabled <6>[ 0.875004] printk: bootconsole [ec_imx21] disabled <6>[ 0.875004] printk: bootconsole [ec_imx21] disabled <6>[ 0.886953] msm_serial: driver initialized <6>[ 0.892529] STMicroelectronics ASC driver initialized <6>[ 0.899805] STM32 USART driver initialized <6>[ 0.927277] brd: module loaded <6>[ 0.938257] loop: module loaded <6>[ 0.945911] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 0.954125] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 0.962449] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 0.970929] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 0.978983] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 0.986811] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 0.994433] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 1.005215] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.012540] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.021647] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.041234] scsi host0: ahci-imx <6>[ 1.045111] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 1.067303] CAN device driver interface <6>[ 1.073324] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.083291] pps pps0: new PPS source ptp0 <3>[ 1.110254] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 1.117743] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 1.125081] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 1.132441] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 1.139806] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 1.147164] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 1.154489] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 1.161855] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 1.169219] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 7 <6>[ 1.377021] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 1.382775] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 1.389361] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 1.672232] Freeing initrd memory: 12928K <4>[ 1.676923] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.687627] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 1.699572] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.707213] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.712454] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.718729] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.724402] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.737108] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.743007] usbcore: registered new interface driver pegasus <6>[ 1.749005] usbcore: registered new interface driver asix <6>[ 1.754711] usbcore: registered new interface driver ax88179_178a <6>[ 1.761130] usbcore: registered new interface driver cdc_ether <6>[ 1.767293] usbcore: registered new interface driver smsc75xx <6>[ 1.773357] usbcore: registered new interface driver smsc95xx <6>[ 1.779433] usbcore: registered new interface driver net1080 <6>[ 1.785418] usbcore: registered new interface driver cdc_subset <6>[ 1.791642] usbcore: registered new interface driver zaurus <6>[ 1.797574] usbcore: registered new interface driver cdc_ncm <6>[ 1.810382] usbcore: registered new interface driver usb-storage <6>[ 1.825520] i2c_dev: i2c /dev entries driver <6>[ 1.854040] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.860542] sdhci: Copyright(c) Pierre Ossman <6>[ 1.868227] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.877191] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.884539] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 1.888955] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 1.889843] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 1.900484] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.908836] usbcore: registered new interface driver usbhid <6>[ 1.914690] usbhid: USB HID core driver <6>[ 1.928897] NET: Registered PF_INET6 protocol family <6>[ 1.932223] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 1.935578] Segment Routing with IPv6 <6>[ 1.945278] In-situ OAM (IOAM) with IPv6 <6>[ 1.949594] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.956445] NET: Registered PF_PACKET protocol family <6>[ 1.961775] can: controller area network core <6>[ 1.966498] NET: Registered PF_CAN protocol family <6>[ 1.971566] can: raw protocol <6>[ 1.972660] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 1.974803] can: broadcast manager protocol <6>[ 1.986436] can: netlink gateway - max_hops=1 <5>[ 1.991439] Key type dns_resolver registered <6>[ 1.998189] ThumbEE CPU extension supported. <5>[ 2.002745] Registering SWP/SWPB emulation handler <5>[ 2.008778] Loading compiled-in X.509 certificates <6>[ 2.019546] pstore: Using crash dump compression: deflate <6>[ 2.019600] mmc2: new high speed SDHC card at address e624 <6>[ 2.032435] mmcblk2: mmc2:e624 SL16G 14.8 GiB <4>[ 2.051583] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.059372] GPT:29296874 != 31116287 <4>[ 2.063249] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.069579] GPT:29296874 != 31116287 <4>[ 2.073443] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.079003] mmcblk2: p1 p2 p3 <4>[ 2.086551] imx_usb 2184200.usb: No over current polarity defined <6>[ 2.096598] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.101770] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.135404] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.142571] hub 1-0:1.0: USB hub found <6>[ 2.146692] hub 1-0:1.0: 1 port detected <6>[ 2.153617] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.176706] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 2.193030] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.435399] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.637114] hub 1-1:1.0: USB hub found <6>[ 2.641333] hub 1-1:1.0: 3 ports detected <6>[ 5.295808] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 5.303646] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.355360] Sending DHCP requests ., OK <6>[ 5.399544] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 5.407915] IP-Config: Complete: <6>[ 5.411430] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.422184] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 5.430298] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.430308] nameserver0=192.168.201.1 <6>[ 5.447700] Freeing unused kernel image (initmem) memory: 2048K <6>[ 5.486369] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u4 <6>[ 6.437762] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 6.445345] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 6.509926] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 6.588254] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.609483] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.631020] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.638023] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 6.640017] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 6.661736] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.669273] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.675750] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.685463] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 6.705400] caam 2100000.crypto: Entropy delay = 3200 <6>[ 6.730622] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 6.753117] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.771530] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 6.832292] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 6.837769] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 6.844664] caam 2100000.crypto: job rings = 2, qi = 0 <3>[ 6.889525] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 7.190353] caam algorithms registered in /proc/crypto <6>[ 7.197280] caam 2100000.crypto: registering rng-caam <6>[ 7.202953] caam 2100000.crypto: rng crypto API alg registered prng-caam Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 7.385013] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.101676] systemd[1]: System time before build time, advancing clock. <30>[ 8.150784] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.175181] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.217697] systemd[1]: Set hostname to . <30>[ 9.051376] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 9.060953] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.073958] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.083717] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 9.126970] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 9.166775] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.206823] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 9.245817] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.286169] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.326149] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.338709] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.376433] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 9.405928] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 9.445751] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 9.475920] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 9.506774] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.583738] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 9.593580] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 9.637027] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 9.677909] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 9.718926] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 9.756179] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 9.796607] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 9.806365] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 9.896243] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 9.939646] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 9.979895] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 10.019436] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 10.059500] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 10.101147] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 10.138306] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 10.152350] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 10.213191] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 10.249077] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 10.289062] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 10.331304] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 10.366124] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.405908] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Create list of st… nodes for the current kernel. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 10.810516] systemd-journald[241]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Sound Card. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 6.1.80-cip16 #1 SMP Sun Mar 3 10:56:33 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12925696/extract-nfsrootfs-qs2ojslk' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12925696/extract-nfsrootfs-qs2ojslk' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12925696/environment . /lava-12925696/environment / # /lava-12925696/bin/lava-test-runner /lava-12925696/0 /lava-12925696/bin/lava-test-runner /lava-12925696/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12925696/0/tests/0_timesync-off ++ cat uuid + UUID=12925696_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-12925696/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=12925696_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip/linux-6.1.y-cip/v6.1.80-cip16/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2024-03-03 11:14:24-- http://storage.kernelci.org/cip/linux-6.1.y-cip/v6.1.80-cip16/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1531868 (1.5M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 1%[ ] 25.18K 95.2KB/s kselftest.tar.xz 4%[ ] 72.78K 137KB/s kselftest.tar.xz 7%[> ] 112.37K 133KB/s kselftest.tar.xz 9%[> ] 143.96K 136KB/s kselftest.tar.xz 11%[=> ] 167.52K 126KB/s kselftest.tar.xz 12%[=> ] 188.73K 119KB/s kselftest.tar.xz 14%[=> ] 211.35K 114KB/s kselftest.tar.xz 15%[==> ] 233.05K 110KB/s kselftest.tar.xz 17%[==> ] 264.16K 111KB/s kselftest.tar.xz 19%[==> ] 294.78K 106KB/s kselftest.tar.xz 21%[===> ] 326.38K 106KB/s eta 11s kselftest.tar.xz 24%[===> ] 360.32K 107KB/s eta 11s kselftest.tar.xz 26%[====> ] 391.42K 108KB/s eta 11s kselftest.tar.xz 28%[====> ] 427.71K 110KB/s eta 11s kselftest.tar.xz 30%[=====> ] 460.71K 111KB/s eta 9s kselftest.tar.xz 31%[=====> ] 477.20K 108KB/s eta 9s kselftest.tar.xz 33%[=====> ] 507.38K 109KB/s eta 9s kselftest.tar.xz 35%[======> ] 532.83K 110KB/s eta 9s kselftest.tar.xz 37%[======> ] 559.70K 105KB/s eta 9s kselftest.tar.xz 38%[======> ] 569.11K 100KB/s eta 9s kselftest.tar.xz 40%[=======> ] 599.29K 103KB/s eta 9s kselftest.tar.xz 41%[=======> ] 623.33K 104KB/s eta 9s kselftest.tar.xz 42%[=======> ] 643.13K 104KB/s eta 9s kselftest.tar.xz 44%[=======> ] 668.58K 105KB/s eta 9s kselftest.tar.xz 46%[========> ] 696.86K 107KB/s eta 7s kselftest.tar.xz 48%[========> ] 718.07K 109KB/s eta 7s kselftest.tar.xz 50%[=========> ] 750.60K 110KB/s eta 7s kselftest.tar.xz 52%[=========> ] 785.95K 113KB/s eta 7s kselftest.tar.xz 54%[=========> ] 811.40K 112KB/s eta 7s kselftest.tar.xz 55%[==========> ] 832.13K 111KB/s eta 6s kselftest.tar.xz 57%[==========> ] 866.07K 111KB/s eta 6s kselftest.tar.xz 59%[==========> ] 891.52K 113KB/s eta 6s kselftest.tar.xz 60%[===========> ] 903.32K 108KB/s eta 6s kselftest.tar.xz 61%[===========> ] 917.46K 105KB/s eta 6s kselftest.tar.xz 62%[===========> ] 934.42K 102KB/s eta 5s kselftest.tar.xz 63%[===========> ] 954.22K 99.1KB/s eta 5s kselftest.tar.xz 65%[============> ] 974.02K 100KB/s eta 5s kselftest.tar.xz 66%[============> ] 993.82K 101KB/s eta 5s kselftest.tar.xz 67%[============> ] 1015K 99.5KB/s eta 5s kselftest.tar.xz 69%[============> ] 1.01M 100KB/s eta 4s kselftest.tar.xz 71%[=============> ] 1.04M 97.5KB/s eta 4s kselftest.tar.xz 73%[=============> ] 1.07M 98.3KB/s eta 4s kselftest.tar.xz 73%[=============> ] 1.08M 95.4KB/s eta 4s kselftest.tar.xz 75%[==============> ] 1.11M 93.0KB/s eta 4s kselftest.tar.xz 77%[==============> ] 1.13M 88.8KB/s eta 4s kselftest.tar.xz 79%[==============> ] 1.15M 86.3KB/s eta 4s kselftest.tar.xz 80%[===============> ] 1.18M 88.2KB/s eta 4s kselftest.tar.xz 82%[===============> ] 1.21M 87.0KB/s eta 2s kselftest.tar.xz 85%[================> ] 1.25M 91.6KB/s eta 2s kselftest.tar.xz 87%[================> ] 1.28M 96.3KB/s eta 2s kselftest.tar.xz 89%[================> ] 1.31M 100KB/s eta 2s kselftest.tar.xz 91%[=================> ] 1.34M 106KB/s eta 2s kselftest.tar.xz 94%[=================> ] 1.38M 108KB/s eta 1s kselftest.tar.xz 97%[==================> ] 1.42M 113KB/s eta 1s kselftest.tar.xz 99%[==================> ] 1.45M 114KB/s eta 1s kselftest.tar.xz 100%[===================>] 1.46M 112KB/s in 14s 2024-03-03 11:14:38 (107 KB/s) - 'kselftest.tar.xz' saved [1531868/1531868] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== shardfile-filesystems pass <12>[ 44.790710] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts Traceback (most recent call last): File "/lava-12925696/0/tests/1_kselftest-filesystems/automated/linux/kselftest/./parse-output.py", line 4, in from tap import parser ModuleNotFoundError: No module named 'tap' + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #