Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.106 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 491639/tftp-deploy-7oohkpmr/kernel/Image tftp 0x82000000 491639/tftp-deploy-7oohkpmr/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491639/tftp-deploy-7oohkpmr/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## 13.2 MiB/s done Bytes transferred = 39019008 (2536200 hex) => tftp 0x90080000 491639/tftp-deploy-7oohkpmr/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 491639/tftp-deploy-7oohkpmr/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491639/tftp-deploy-7oohkpmr/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.8 MiB/s done Bytes transferred = 26569551 (1956b4f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 491639/tftp-deploy-7oohkpmr/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 491639/tftp-deploy-7oohkpmr/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491639/tftp-deploy-7oohkpmr/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *### 4 MiB/s done Bytes transferred = 29617 (73b1 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-08-30 4:32:01 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 26569487 Bytes = 25.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a3b0 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.11.0-rc5 (KernelCI@build-j301321-arm64-clang-15-defconfig-config-arm64-64k-pagkh9s) (Debian clang version 15.0.7, Debian LLD 15.0.7) #1 SMP PREEMPT Fri Aug 30 04:06:13 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20fff456c0-0x20fff480ff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 1056 pages in unavailable ranges [ 0.000000] cma: Reserved 512 MiB at 0x00000000c0000000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 2 pages/cpu s60248 r8192 d62632 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64480 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f7d30000-0x00000000fbd30000] (64MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080180000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080150000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080160000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008836] Console: colour dummy device 80x25 <6>[ 0.013670] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024391] pid_max: default: 32768 minimum: 301 <6>[ 0.029357] LSM: initializing lsm=capability <6>[ 0.033993] Mount-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) <6>[ 0.041740] Mountpoint-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) <6>[ 0.051338] rcu: Hierarchical SRCU implementation. <6>[ 0.056458] rcu: Max phase no-delay instances is 1000. <6>[ 0.062147] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.070709] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.077581] EFI services will not be available. <6>[ 0.082563] smp: Bringing up secondary CPUs ... <6>[ 0.087693] Detected PIPT I-cache on CPU1 <6>[ 0.087734] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.087743] GICv3: CPU1: using allocated LPI pending table @0x0000002080170000 <6>[ 0.087768] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.087862] smp: Brought up 1 node, 2 CPUs <6>[ 0.118180] SMP: Total of 2 processors activated. <6>[ 0.123192] CPU: All CPU(s) started at EL2 <6>[ 0.127609] CPU features: detected: 32-bit EL0 Support <6>[ 0.133061] CPU features: detected: 32-bit EL1 Support <6>[ 0.138519] CPU features: detected: CRC32 instructions <6>[ 0.143991] alternatives: applying system-wide alternatives <6>[ 0.150778] Memory: 3449024K/4126720K available (17536K kernel code, 5272K rwdata, 11840K rodata, 2880K init, 1171K bss, 143680K reserved, 524288K cma-reserved) <6>[ 0.166041] devtmpfs: initialized <6>[ 0.172685] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.182822] futex hash table entries: 512 (order: -1, 32768 bytes, linear) <6>[ 0.190506] 1427 pages in range for non-PLT usage <6>[ 0.190511] 32147 pages in range for PLT usage <6>[ 0.195635] pinctrl core: initialized pinctrl subsystem <6>[ 0.206396] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.214043] SoC family: QorIQ LS1028A <6>[ 0.217996] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.223283] DMI not present or invalid. <6>[ 0.228688] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.237938] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.245446] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.253638] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.261935] audit: initializing netlink subsys (disabled) <5>[ 0.267979] audit: type=2000 audit(0.156:1): state=initialized audit_enabled=0 res=1 <6>[ 0.268871] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.276078] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.282450] cpuidle: using governor menu <6>[ 0.293715] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.300863] ASID allocator initialised with 65536 entries <6>[ 0.307953] Serial: AMBA PL011 UART driver <6>[ 0.325176] HugeTLB: registered 16.0 GiB page size, pre-allocated 0 pages <6>[ 0.332304] HugeTLB: 0 KiB vmemmap can be freed for a 16.0 GiB page <6>[ 0.338897] HugeTLB: registered 512 MiB page size, pre-allocated 0 pages <6>[ 0.345925] HugeTLB: 0 KiB vmemmap can be freed for a 512 MiB page <6>[ 0.352428] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.359544] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.367532] ACPI: Interpreter disabled. <6>[ 0.373200] iommu: Default domain type: Translated <6>[ 0.378304] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.384959] SCSI subsystem initialized <6>[ 0.389216] usbcore: registered new interface driver usbfs <6>[ 0.395039] usbcore: registered new interface driver hub <6>[ 0.400680] usbcore: registered new device driver usb <6>[ 0.406649] i2c i2c-0: IMX I2C adapter registered <6>[ 0.411958] i2c i2c-1: IMX I2C adapter registered <6>[ 0.417279] i2c i2c-2: IMX I2C adapter registered <6>[ 0.422731] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.428022] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.437528] PTP clock support registered <6>[ 0.441866] EDAC MC: Ver: 3.0.0 <6>[ 0.445541] scmi_core: SCMI protocol bus registered <6>[ 0.451271] FPGA manager framework <6>[ 0.455024] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.461996] vgaarb: loaded <6>[ 0.465234] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.471919] VFS: Disk quotas dquot_6.6.0 <6>[ 0.476170] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes) <6>[ 0.483717] pnp: PnP ACPI: disabled <6>[ 0.491563] NET: Registered PF_INET protocol family <6>[ 0.496929] IP idents hash table entries: 65536 (order: 3, 524288 bytes, linear) <6>[ 0.506594] tcp_listen_portaddr_hash hash table entries: 4096 (order: 0, 65536 bytes, linear) <6>[ 0.515542] Table-perturb hash table entries: 65536 (order: 2, 262144 bytes, linear) <6>[ 0.523636] TCP established hash table entries: 32768 (order: 2, 262144 bytes, linear) <6>[ 0.531978] TCP bind hash table entries: 32768 (order: 4, 1048576 bytes, linear) <6>[ 0.540390] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.547321] UDP hash table entries: 2048 (order: 0, 65536 bytes, linear) <6>[ 0.554387] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes, linear) <6>[ 0.561963] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.568235] RPC: Registered named UNIX socket transport module. <6>[ 0.574484] RPC: Registered udp transport module. <6>[ 0.579495] RPC: Registered tcp transport module. <6>[ 0.584505] RPC: Registered tcp-with-tls transport module. <6>[ 0.590308] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.597081] PCI: CLS 0 bytes, default 64 <6>[ 0.601415] Unpacking initramfs... <6>[ 0.607892] kvm [1]: nv: 529 coarse grained trap handlers <6>[ 0.613946] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.618751] kvm [1]: GICv3: no GICV resource entry <6>[ 0.623869] kvm [1]: disabling GICv2 emulation <6>[ 0.628632] kvm [1]: GIC system register CPU interface enabled <6>[ 0.634806] kvm [1]: vgic interrupt IRQ9 <6>[ 0.639046] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.645607] Initialise system trusted keyrings <6>[ 0.650497] workingset: timestamp_bits=42 max_order=16 bucket_order=0 <6>[ 0.657507] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.663910] NFS: Registering the id_resolver key type <5>[ 0.669317] Key type id_resolver registered <5>[ 0.673818] Key type id_legacy registered <6>[ 0.678159] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.685217] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.693078] 9p: Installing v9fs 9p2000 file system support <5>[ 0.722450] Key type asymmetric registered <5>[ 0.726856] Asymmetric key parser 'x509' registered <6>[ 0.732098] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.739836] io scheduler mq-deadline registered <6>[ 0.744673] io scheduler kyber registered <6>[ 0.749026] io scheduler bfq registered <6>[ 0.760824] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.768972] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.778145] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.787302] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.796458] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.805609] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.814761] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.823908] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.833097] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.842331] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.849643] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.855185] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.862569] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.870393] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.877776] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.885599] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.893005] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.900850] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.908281] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 0.917995] pci 0000:00:00.0: BAR 0 [mem 0x1f8000000-0x1f803ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 0.928635] pci 0000:00:00.0: BAR 2 [mem 0x1f8160000-0x1f816ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 0.939712] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81d0000-0x1f81dffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 0.950607] pci 0000:00:00.0: VF BAR 4 [mem 0x1f81f0000-0x1f81fffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 0.961958] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.967776] pci 0000:00:00.0: VF BAR 0 [mem 0x1f81d0000-0x1f81effff 64bit]: contains BAR 0 for 2 VFs <6>[ 0.977267] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81f0000-0x1f820ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 0.987410] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 0.997128] pci 0000:00:00.1: BAR 0 [mem 0x1f8040000-0x1f807ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.007774] pci 0000:00:00.1: BAR 2 [mem 0x1f8170000-0x1f817ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.018848] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8210000-0x1f821ffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 1.029750] pci 0000:00:00.1: VF BAR 4 [mem 0x1f8230000-0x1f823ffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 1.041100] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.046914] pci 0000:00:00.1: VF BAR 0 [mem 0x1f8210000-0x1f822ffff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.056404] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8230000-0x1f824ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.066550] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.076254] pci 0000:00:00.2: BAR 0 [mem 0x1f8080000-0x1f80bffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.086887] pci 0000:00:00.2: BAR 2 [mem 0x1f8180000-0x1f818ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.097978] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.103987] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.113691] pci 0000:00:00.3: BAR 0 [mem 0x1f8100000-0x1f811ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.124345] pci 0000:00:00.3: BAR 2 [mem 0x1f8190000-0x1f819ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.135438] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.141423] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.151122] pci 0000:00:00.4: BAR 0 [mem 0x1f8120000-0x1f813ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.161765] pci 0000:00:00.4: BAR 2 [mem 0x1f81a0000-0x1f81affff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.172850] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.178858] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 PCIe Root Complex Integrated Endpoint <6>[ 1.188565] pci 0000:00:00.5: BAR 0 [mem 0x1f8140000-0x1f815ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.199203] pci 0000:00:00.5: BAR 2 [mem 0x1f81b0000-0x1f81bffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.210275] pci 0000:00:00.5: BAR 4 [mem 0x1fc000000-0x1fc3fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.220928] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.226957] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.236660] pci 0000:00:00.6: BAR 0 [mem 0x1f80c0000-0x1f80fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.247311] pci 0000:00:00.6: BAR 2 [mem 0x1f81c0000-0x1f81cffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.258413] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.265108] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 PCIe Root Complex Event Collector <6>[ 1.274484] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.282481] pci_bus 0000:00: resource 4 [mem 0x1f8000000-0x1f815ffff] <6>[ 1.289264] pci_bus 0000:00: resource 5 [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.296474] pci_bus 0000:00: resource 6 [mem 0x1f81d0000-0x1f81effff] <6>[ 1.303241] pci_bus 0000:00: resource 7 [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.310447] pci_bus 0000:00: resource 8 [mem 0x1f8210000-0x1f822ffff] <6>[ 1.317215] pci_bus 0000:00: resource 9 [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.324423] pci_bus 0000:00: resource 10 [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.437255] pci 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 1.444996] pci 0000:00:00.1: enetc_fixup_clear_rss_rfs+0x0/0x58 took 111027 usecs <6>[ 1.523120] Freeing initrd memory: 25856K <6>[ 1.557249] pci 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 1.563857] pci 0000:00:00.2: enetc_fixup_clear_rss_rfs+0x0/0x58 took 108302 usecs <6>[ 1.677248] pci 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 1.683830] pci 0000:00:00.6: enetc_fixup_clear_rss_rfs+0x0/0x58 took 109392 usecs <6>[ 1.691773] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.699925] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.706201] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.712811] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.720502] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.729398] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.738336] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 2.745243] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.751642] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.758678] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.764482] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.770987] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.781899] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 2.789561] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.795148] pci 0001:00:00.0: supports D1 D2 <6>[ 2.799722] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.806943] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.812492] pci_bus 0001:00: resource 4 [io 0x0000-0xffff] <6>[ 2.818382] pci_bus 0001:00: resource 5 [mem 0x8040000000-0x807fffffff] <6>[ 2.825415] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.833087] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.841978] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.850894] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.857243] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.863644] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.870680] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.876485] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.885799] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.896706] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 3.904369] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.909955] pci 0002:00:00.0: supports D1 D2 <6>[ 3.914529] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.921731] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.927279] pci_bus 0002:00: resource 4 [io 0x10000-0x1ffff] <6>[ 3.933345] pci_bus 0002:00: resource 5 [mem 0x8840000000-0x887fffffff] <6>[ 3.959567] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.968047] printk: legacy console [ttyS0] disabled <6>[ 3.973433] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.982597] printk: legacy console [ttyS0] enabled <6>[ 3.982597] printk: legacy console [ttyS0] enabled <6>[ 3.992767] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.992767] printk: legacy bootconsole [ns16550a0] disabled <6>[ 4.005798] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 4.015722] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 4.025718] msm_serial: driver initialized <6>[ 4.030313] SuperH (H)SCI(F) driver initialized <6>[ 4.035226] STM32 USART driver initialized <5>[ 4.042930] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.049694] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.054592] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.060190] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.065788] arm-smmu 5000000.iommu: nested translation <5>[ 4.071295] arm-smmu 5000000.iommu: coherent table walk <5>[ 4.076892] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 4.084496] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.091926] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.098751] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.105483] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.112210] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.119146] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 4.125321] arm-smmu 5000000.iommu: Failed to disable prefetcher [errata #841119 and #826419], check ACR.CACHE_LOCK <6>[ 4.139323] loop: module loaded <6>[ 4.151119] megasas: 07.727.03.00-rc1 <5>[ 4.189092] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.196206] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.201716] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.207433] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.214411] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.221473] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.227680] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.237825] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.243795] thunder_xcv, ver 1.0 <6>[ 4.247322] thunder_bgx, ver 1.0 <6>[ 4.250843] nicpf, ver 1.0 <6>[ 4.254563] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 0 <6>[ 4.365247] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.390808] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 1 <6>[ 4.397127] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.404084] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.413106] pps pps0: new PPS source ptp0 <6>[ 4.417903] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.425424] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.431062] hclge is initializing <6>[ 4.434683] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.439843] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.445895] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.451143] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.457368] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.463049] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.468921] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.475473] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.481917] sky2: driver version 1.30 <6>[ 4.486754] VFIO - User Level meta-driver version: 0.3 <6>[ 4.492482] dwc3 3100000.usb: Adding to iommu group 2 <6>[ 4.498916] dwc3 3110000.usb: Adding to iommu group 3 <6>[ 4.507545] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.513340] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.521502] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.531207] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x03100000 <6>[ 4.537482] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.543254] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.551232] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.558436] hub 1-0:1.0: USB hub found <6>[ 4.562482] hub 1-0:1.0: 1 port detected <6>[ 4.566866] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.575613] hub 2-0:1.0: USB hub found <6>[ 4.579658] hub 2-0:1.0: 1 port detected <6>[ 4.584081] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.589871] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.598033] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.607757] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03110000 <6>[ 4.614039] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.619813] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.627769] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.634908] hub 3-0:1.0: USB hub found <6>[ 4.638965] hub 3-0:1.0: 1 port detected <6>[ 4.643341] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.652000] hub 4-0:1.0: USB hub found <6>[ 4.656041] hub 4-0:1.0: 1 port detected <6>[ 4.660756] usbcore: registered new interface driver usb-storage <6>[ 4.669261] i2c_dev: i2c /dev entries driver <6>[ 4.677382] sp805-wdt c000000.watchdog: registration successful <6>[ 4.683804] sp805-wdt c010000.watchdog: registration successful <6>[ 4.692102] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.701057] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.707535] sdhci: Copyright(c) Pierre Ossman <6>[ 4.712694] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.719647] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.726196] sdhci-esdhc 2140000.mmc: Adding to iommu group 4 <6>[ 4.732179] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.732309] sdhci-esdhc 2150000.mmc: Adding to iommu group 5 <6>[ 4.745351] usbcore: registered new interface driver usbhid <6>[ 4.751685] usbhid: USB HID core driver <6>[ 4.758275] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 4.770780] NET: Registered PF_PACKET protocol family <6>[ 4.776188] 9pnet: Installing 9P2000 support <6>[ 4.780754] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.781246] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <5>[ 4.787990] Key type dns_resolver registered <6>[ 4.806274] registered taskstats version 1 <5>[ 4.810802] Loading compiled-in X.509 certificates <6>[ 4.821745] Demotion targets for Node 0: null <6>[ 4.828822] fsl-edma 22c0000.dma-controller: Adding to iommu group 6 <6>[ 4.836701] pcieport 0001:00:00.0: Adding to iommu group 7 <6>[ 4.842745] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.849058] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.855234] pcieport 0002:00:00.0: Adding to iommu group 8 <6>[ 4.861191] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.867473] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.876166] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.901249] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.923884] mmc0: new HS400 MMC card at address 0001 <6>[ 4.929562] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.935826] mmcblk0: p1 p2 <6>[ 4.939423] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.945497] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.951585] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 5.115025] hub 3-1:1.0: USB hub found <6>[ 5.119242] hub 3-1:1.0: 7 ports detected <6>[ 17.153364] clk: Disabling unused clocks <6>[ 17.157632] PM: genpd: Disabling unused power domains <6>[ 17.163016] ALSA device list: <6>[ 17.166295] No soundcards found. <6>[ 17.171811] Freeing unused kernel memory: 2880K <6>[ 17.176757] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 17.240818] udevd[107]: starting version 3.2.9 <5>[ 18.377243] random: crng init done <27>[ 18.383629] udevd[107]: specified user 'tss' unknown <27>[ 18.389027] udevd[107]: specified group 'tss' unknown <30>[ 18.395834] udevd[108]: starting eudev-3.2.9 <3>[ 18.644831] thermal_sys: Thermal zone name (core-cluster-thermal) too long, should be under 20 chars <3>[ 18.656386] thermal_sys: Failed to register thermal zone core-cluster-thermal: -22 <6>[ 18.676857] NET: Registered PF_INET6 protocol family <3>[ 18.678725] qoriq_thermal 1f80000.tmu: Failed to register sensors <3>[ 18.694369] qoriq_thermal 1f80000.tmu: probe with driver qoriq_thermal failed with error -22 <4>[ 18.708169] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 18.708979] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 18.715635] Segment Routing with IPv6 <4>[ 18.725765] wm8904 2-001a: supply DCVDD not found, using dummy regulator <6>[ 18.729303] In-situ OAM (IOAM) with IPv6 <4>[ 18.736971] wm8904 2-001a: supply DBVDD not found, using dummy regulator <6>[ 18.748102] fsl_ddr_edac acquired irq 108 for MC <6>[ 18.753314] fsl_ddr_edac MC err registered <6>[ 18.757486] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.758101] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 18.771750] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 18.778777] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 18.789456] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 18.791443] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 18.808664] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 18.814919] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 18.836833] wm8904 2-001a: revision A <6>[ 18.841742] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 18.854049] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 18.861627] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 18.869803] rtc-rv8803 0-0032: registered as rtc0 <6>[ 18.876098] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.876815] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 18.889520] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 18.904613] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 18.919638] CAN device driver interface <6>[ 18.929893] input: buttons1 as /devices/platform/buttons1/input/input9 <6>[ 18.944544] ftm-alarm 2800000.rtc: registered as rtc1 <6>[ 19.003682] caam 8000000.crypto: Entropy delay = 3200 <6>[ 19.017847] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 19.023400] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 19.024050] mali-dp f080000.display: Adding to iommu group 9 <6>[ 19.028877] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 19.042446] usbcore: registered new device driver onboard-usb-dev <6>[ 19.049466] caam 8000000.crypto: job rings = 4, qi = 0 <4>[ 19.067999] sysfs: cannot create duplicate filename '/devices/platform/sound/sai-tx-rx-wm8904-hifi' <6>[ 19.069560] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 19.087592] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <4>[ 19.094726] CPU: 0 UID: 0 PID: 117 Comm: udevd Not tainted 6.11.0-rc5 #1 <4>[ 19.101720] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT) <4>[ 19.110275] Call trace: <4>[ 19.112985] dump_backtrace+0xec/0x108 <4>[ 19.117016] show_stack+0x18/0x24 <4>[ 19.120605] dump_stack_lvl+0x40/0x84 <4>[ 19.124543] dump_stack+0x18/0x24 <4>[ 19.128129] sysfs_create_dir_ns+0xe8/0x144 <4>[ 19.132590] kobject_add_internal+0x220/0x3cc <4>[ 19.137221] kobject_add+0x94/0x108 <4>[ 19.140979] device_add+0x148/0x448 <4>[ 19.144739] device_register+0x20/0x30 <4>[ 19.148762] snd_soc_add_pcm_runtimes+0x578/0xb4c <4>[ 19.153743] snd_soc_bind_card+0x3a8/0xd94 <6>[ 19.157448] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <4>[ 19.158111] snd_soc_register_card+0xf0/0x108 <4>[ 19.169196] devm_snd_soc_register_card+0x4c/0x90 <4>[ 19.174178] simple_probe+0x340/0x390 [snd_soc_simple_card] <4>[ 19.180037] platform_probe+0xa8/0xd0 <4>[ 19.183972] really_probe+0x128/0x2c8 <4>[ 19.187907] __driver_probe_device+0xa0/0x128 <4>[ 19.192541] driver_probe_device+0x3c/0x1f8 <4>[ 19.196999] __driver_attach+0xdc/0x1a4 <4>[ 19.201109] bus_for_each_dev+0xec/0x144 <4>[ 19.205305] driver_attach+0x24/0x30 <4>[ 19.209152] bus_add_driver+0x154/0x26c <4>[ 19.213260] driver_register+0x68/0x100 <4>[ 19.217369] __platform_driver_register+0x24/0x30 <4>[ 19.222353] init_module+0x20/0xffe8 [snd_soc_simple_card] <4>[ 19.228119] do_one_initcall+0xcc/0x240 <4>[ 19.232228] do_init_module+0x54/0x28c <4>[ 19.236252] load_module+0x1470/0x1714 <4>[ 19.240274] __arm64_sys_finit_module+0x264/0x300 <4>[ 19.245256] invoke_syscall+0x48/0xd0 <4>[ 19.249192] do_el0_svc+0x7c/0xa8 <4>[ 19.252777] el0_svc+0x34/0x7c <4>[ 19.256103] el0t_64_sync_handler+0x84/0xfc <4>[ 19.260561] el0t_64_sync+0x190/0x194 <3>[ 19.265527] kobject: kobject_add_internal failed for sai-tx-rx-wm8904-hifi with -EEXIST, don't try to register things with the same name in the same directory. <3>[ 19.280272] asoc-simple-card sound: probe with driver asoc-simple-card failed with error -12 <6>[ 19.297124] caam_jr 8010000.jr: Adding to iommu group 10 <6>[ 19.317349] caam algorithms registered in /proc/crypto <6>[ 19.322846] caam 8000000.crypto: registering rng-caam <6>[ 19.328317] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.335541] caam_jr 8020000.jr: Adding to iommu group 11 <6>[ 19.341799] caam_jr 8030000.jr: Adding to iommu group 12 <6>[ 19.349539] caam_jr 8040000.jr: Adding to iommu group 13 done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-491639/environment . /lava-491639/environment / # /lava-491639/bin/lava-test-runner /lava-491639/0 /lava-491639/bin/lava-test-runner /lava-491639/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 19.962295] d /lava-491639/0/tests/0_dmesg + cat uuid + UUID=491639_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.983837] <8>[ 20.005613] <8>[ 20.028608] + set +x <8>[ 20.037929] / #