Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.106 (254 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 491625/tftp-deploy-b0wz6q19/kernel/Image tftp 0x82000000 491625/tftp-deploy-b0wz6q19/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491625/tftp-deploy-b0wz6q19/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################ 14.5 MiB/s done Bytes transferred = 45308416 (2b35a00 hex) => tftp 0x90080000 491625/tftp-deploy-b0wz6q19/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 491625/tftp-deploy-b0wz6q19/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491625/tftp-deploy-b0wz6q19/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######## 6 MiB/s done Bytes transferred = 25876574 (18ad85e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 491625/tftp-deploy-b0wz6q19/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 491625/tftp-deploy-b0wz6q19/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491625/tftp-deploy-b0wz6q19/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *### 4 MiB/s done Bytes transferred = 29617 (73b1 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-08-30 4:13:20 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 25876510 Bytes = 24.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a3b0 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.11.0-rc5 (KernelCI@build-j301284-arm64-gcc-12-defconfig-ltbjp) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Aug 30 03:55:04 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7fe9c0-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 24 pages/cpu s60056 r8192 d30056 u98304 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031680 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080040000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080050000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008838] Console: colour dummy device 80x25 <6>[ 0.013644] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024365] pid_max: default: 32768 minimum: 301 <6>[ 0.029328] LSM: initializing lsm=capability <6>[ 0.033962] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041710] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051072] rcu: Hierarchical SRCU implementation. <6>[ 0.056191] rcu: Max phase no-delay instances is 1000. <6>[ 0.061866] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.070423] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.077279] EFI services will not be available. <6>[ 0.082212] smp: Bringing up secondary CPUs ... <6>[ 0.087335] Detected PIPT I-cache on CPU1 <6>[ 0.087376] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.087385] GICv3: CPU1: using allocated LPI pending table @0x0000002080060000 <6>[ 0.087411] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.087492] smp: Brought up 1 node, 2 CPUs <6>[ 0.117811] SMP: Total of 2 processors activated. <6>[ 0.122822] CPU: All CPU(s) started at EL2 <6>[ 0.127239] CPU features: detected: 32-bit EL0 Support <6>[ 0.132692] CPU features: detected: 32-bit EL1 Support <6>[ 0.138150] CPU features: detected: CRC32 instructions <6>[ 0.143625] alternatives: applying system-wide alternatives <6>[ 0.150334] Memory: 3871632K/4126720K available (17152K kernel code, 5014K rwdata, 11660K rodata, 10240K init, 733K bss, 217748K reserved, 32768K cma-reserved) <6>[ 0.165456] devtmpfs: initialized <6>[ 0.172661] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.182798] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.190369] 21504 pages in range for non-PLT usage <6>[ 0.190373] 513024 pages in range for PLT usage <6>[ 0.195582] pinctrl core: initialized pinctrl subsystem <6>[ 0.206441] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.214088] SoC family: QorIQ LS1028A <6>[ 0.218041] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.223349] DMI not present or invalid. <6>[ 0.229332] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.236073] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.243573] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.251805] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.260097] audit: initializing netlink subsys (disabled) <5>[ 0.265910] audit: type=2000 audit(0.156:1): state=initialized audit_enabled=0 res=1 <6>[ 0.266563] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.274002] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.280369] cpuidle: using governor menu <6>[ 0.291583] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.298731] ASID allocator initialised with 65536 entries <6>[ 0.305663] Serial: AMBA PL011 UART driver <6>[ 0.322752] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.329883] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.336479] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.343596] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.350187] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.357303] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.363893] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.371009] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.378702] ACPI: Interpreter disabled. <6>[ 0.384356] iommu: Default domain type: Translated <6>[ 0.389461] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.396136] SCSI subsystem initialized <6>[ 0.400400] usbcore: registered new interface driver usbfs <6>[ 0.406224] usbcore: registered new interface driver hub <6>[ 0.411866] usbcore: registered new device driver usb <6>[ 0.417818] i2c i2c-0: IMX I2C adapter registered <6>[ 0.423115] i2c i2c-1: IMX I2C adapter registered <6>[ 0.428473] i2c i2c-2: IMX I2C adapter registered <6>[ 0.433930] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.439210] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.448713] PTP clock support registered <6>[ 0.453043] EDAC MC: Ver: 3.0.0 <6>[ 0.456741] scmi_core: SCMI protocol bus registered <6>[ 0.462491] FPGA manager framework <6>[ 0.466233] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.473178] vgaarb: loaded <6>[ 0.476417] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.482970] VFS: Disk quotas dquot_6.6.0 <6>[ 0.487209] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.494552] pnp: PnP ACPI: disabled <6>[ 0.502685] NET: Registered PF_INET protocol family <6>[ 0.508055] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.517799] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.526727] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.534824] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.543172] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.551521] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.558485] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.565567] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.573149] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.579454] RPC: Registered named UNIX socket transport module. <6>[ 0.585703] RPC: Registered udp transport module. <6>[ 0.590715] RPC: Registered tcp transport module. <6>[ 0.595726] RPC: Registered tcp-with-tls transport module. <6>[ 0.601527] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.608300] PCI: CLS 0 bytes, default 64 <6>[ 0.612659] Unpacking initramfs... <6>[ 0.618917] kvm [1]: nv: 529 coarse grained trap handlers <6>[ 0.624947] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.630783] kvm [1]: GICv3: no GICV resource entry <6>[ 0.635913] kvm [1]: disabling GICv2 emulation <6>[ 0.640690] kvm [1]: GIC system register CPU interface enabled <6>[ 0.646870] kvm [1]: vgic interrupt IRQ9 <6>[ 0.651121] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.657747] Initialise system trusted keyrings <6>[ 0.662659] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.669657] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.676026] NFS: Registering the id_resolver key type <5>[ 0.681434] Key type id_resolver registered <5>[ 0.685928] Key type id_legacy registered <6>[ 0.690270] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.697307] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.705186] 9p: Installing v9fs 9p2000 file system support <5>[ 0.739988] Key type asymmetric registered <5>[ 0.744422] Asymmetric key parser 'x509' registered <6>[ 0.749673] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.757426] io scheduler mq-deadline registered <6>[ 0.762268] io scheduler kyber registered <6>[ 0.766636] io scheduler bfq registered <6>[ 0.778365] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.786512] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.795694] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.804872] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.814049] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.823230] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.832406] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.841587] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.850813] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.860103] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.867435] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.872992] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.880381] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.888222] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.895623] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.903464] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.910875] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.918717] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.926172] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 0.935896] pci 0000:00:00.0: BAR 0 [mem 0x1f8000000-0x1f803ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 0.946552] pci 0000:00:00.0: BAR 2 [mem 0x1f8160000-0x1f816ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 0.957640] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81d0000-0x1f81dffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 0.968553] pci 0000:00:00.0: VF BAR 4 [mem 0x1f81f0000-0x1f81fffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 0.979953] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.985789] pci 0000:00:00.0: VF BAR 0 [mem 0x1f81d0000-0x1f81effff 64bit]: contains BAR 0 for 2 VFs <6>[ 0.995297] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81f0000-0x1f820ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.005463] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.015186] pci 0000:00:00.1: BAR 0 [mem 0x1f8040000-0x1f807ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.025837] pci 0000:00:00.1: BAR 2 [mem 0x1f8170000-0x1f817ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.036924] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8210000-0x1f821ffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 1.047847] pci 0000:00:00.1: VF BAR 4 [mem 0x1f8230000-0x1f823ffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 1.059218] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.065046] pci 0000:00:00.1: VF BAR 0 [mem 0x1f8210000-0x1f822ffff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.074551] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8230000-0x1f824ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.084722] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.094446] pci 0000:00:00.2: BAR 0 [mem 0x1f8080000-0x1f80bffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.105088] pci 0000:00:00.2: BAR 2 [mem 0x1f8180000-0x1f818ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.116175] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.122202] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.131907] pci 0000:00:00.3: BAR 0 [mem 0x1f8100000-0x1f811ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.142540] pci 0000:00:00.3: BAR 2 [mem 0x1f8190000-0x1f819ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.153625] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.159620] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.169328] pci 0000:00:00.4: BAR 0 [mem 0x1f8120000-0x1f813ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.179966] pci 0000:00:00.4: BAR 2 [mem 0x1f81a0000-0x1f81affff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.191053] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.197089] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 PCIe Root Complex Integrated Endpoint <6>[ 1.206790] pci 0000:00:00.5: BAR 0 [mem 0x1f8140000-0x1f815ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.217442] pci 0000:00:00.5: BAR 2 [mem 0x1f81b0000-0x1f81bffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.228527] pci 0000:00:00.5: BAR 4 [mem 0x1fc000000-0x1fc3fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.239176] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.245222] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.254922] pci 0000:00:00.6: BAR 0 [mem 0x1f80c0000-0x1f80fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.265558] pci 0000:00:00.6: BAR 2 [mem 0x1f81c0000-0x1f81cffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.276646] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.283369] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 PCIe Root Complex Event Collector <6>[ 1.292750] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.300729] pci_bus 0000:00: resource 4 [mem 0x1f8000000-0x1f815ffff] <6>[ 1.307505] pci_bus 0000:00: resource 5 [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.314712] pci_bus 0000:00: resource 6 [mem 0x1f81d0000-0x1f81effff] <6>[ 1.321481] pci_bus 0000:00: resource 7 [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.328689] pci_bus 0000:00: resource 8 [mem 0x1f8210000-0x1f822ffff] <6>[ 1.335484] pci_bus 0000:00: resource 9 [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.342709] pci_bus 0000:00: resource 10 [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.456440] pci 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 1.463243] pci 0000:00:00.1: enetc_fixup_clear_rss_rfs+0x0/0x5c took 110967 usecs <6>[ 1.516482] Freeing initrd memory: 25264K <6>[ 1.576431] pci 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 1.582748] pci 0000:00:00.2: enetc_fixup_clear_rss_rfs+0x0/0x5c took 108930 usecs <6>[ 1.696430] pci 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 1.702697] pci 0000:00:00.6: enetc_fixup_clear_rss_rfs+0x0/0x5c took 109365 usecs <6>[ 1.710643] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.718815] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.725097] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.731705] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.739379] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.748263] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.757177] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 2.764424] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.770826] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.777863] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.783667] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.790173] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.801084] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 2.808746] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.814333] pci 0001:00:00.0: supports D1 D2 <6>[ 2.818908] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.826140] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.831689] pci_bus 0001:00: resource 4 [io 0x0000-0xffff] <6>[ 2.837580] pci_bus 0001:00: resource 5 [mem 0x8040000000-0x807fffffff] <6>[ 2.844635] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.852306] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.861197] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.870113] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.876423] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.882815] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.889851] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.895655] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.904968] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.915875] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 3.923538] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.929122] pci 0002:00:00.0: supports D1 D2 <6>[ 3.933696] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.940907] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.946454] pci_bus 0002:00: resource 4 [io 0x10000-0x1ffff] <6>[ 3.952540] pci_bus 0002:00: resource 5 [mem 0x8840000000-0x887fffffff] <6>[ 3.978794] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.987228] printk: legacy console [ttyS0] disabled <6>[ 3.992616] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 4.001784] printk: legacy console [ttyS0] enabled <6>[ 4.001784] printk: legacy console [ttyS0] enabled <6>[ 4.011956] printk: legacy bootconsole [ns16550a0] disabled <6>[ 4.011956] printk: legacy bootconsole [ns16550a0] disabled <6>[ 4.024961] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 4.034910] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 4.044922] msm_serial: driver initialized <6>[ 4.049516] SuperH (H)SCI(F) driver initialized <6>[ 4.054428] STM32 USART driver initialized <5>[ 4.062152] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.068894] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.073792] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.079389] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.084986] arm-smmu 5000000.iommu: nested translation <5>[ 4.090493] arm-smmu 5000000.iommu: coherent table walk <5>[ 4.096090] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 4.103694] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.111129] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.117950] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.124682] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.131409] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.138354] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 4.144528] arm-smmu 5000000.iommu: Failed to disable prefetcher [errata #841119 and #826419], check ACR.CACHE_LOCK <6>[ 4.158626] loop: module loaded <6>[ 4.170152] megasas: 07.727.03.00-rc1 <5>[ 4.209245] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.216366] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.221876] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.227585] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.234585] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.241571] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.247769] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.257907] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.263890] thunder_xcv, ver 1.0 <6>[ 4.267419] thunder_bgx, ver 1.0 <6>[ 4.270940] nicpf, ver 1.0 <6>[ 4.274683] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 0 <6>[ 4.388431] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.414554] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 1 <6>[ 4.420872] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.427824] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.436857] pps pps0: new PPS source ptp0 <6>[ 4.441652] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.449176] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.454831] hclge is initializing <6>[ 4.458438] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.463598] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.469655] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.474903] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.481131] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.486812] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.492687] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.499239] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.505680] sky2: driver version 1.30 <6>[ 4.510523] VFIO - User Level meta-driver version: 0.3 <6>[ 4.516279] dwc3 3100000.usb: Adding to iommu group 2 <6>[ 4.522130] dwc3 3110000.usb: Adding to iommu group 3 <6>[ 4.530323] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.536118] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.544194] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.553899] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x03100000 <6>[ 4.560187] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.565959] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.573939] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.581149] hub 1-0:1.0: USB hub found <6>[ 4.585198] hub 1-0:1.0: 1 port detected <6>[ 4.589584] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.598251] hub 2-0:1.0: USB hub found <6>[ 4.602293] hub 2-0:1.0: 1 port detected <6>[ 4.606712] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.612499] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.620566] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.630292] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03110000 <6>[ 4.636592] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.642366] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.650338] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.657482] hub 3-0:1.0: USB hub found <6>[ 4.661525] hub 3-0:1.0: 1 port detected <6>[ 4.665908] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.674578] hub 4-0:1.0: USB hub found <6>[ 4.678619] hub 4-0:1.0: 1 port detected <6>[ 4.683367] usbcore: registered new interface driver usb-storage <6>[ 4.691845] i2c_dev: i2c /dev entries driver <6>[ 4.699977] sp805-wdt c000000.watchdog: registration successful <6>[ 4.706371] sp805-wdt c010000.watchdog: registration successful <6>[ 4.714707] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.723637] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.730116] sdhci: Copyright(c) Pierre Ossman <6>[ 4.735270] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.742221] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.748780] sdhci-esdhc 2140000.mmc: Adding to iommu group 4 <6>[ 4.754762] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.754892] sdhci-esdhc 2150000.mmc: Adding to iommu group 5 <6>[ 4.768291] usbcore: registered new interface driver usbhid <6>[ 4.774450] usbhid: USB HID core driver <6>[ 4.781136] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 4.789694] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.800930] NET: Registered PF_PACKET protocol family <6>[ 4.806295] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.808500] 9pnet: Installing 9P2000 support <5>[ 4.818119] Key type dns_resolver registered <6>[ 4.829033] registered taskstats version 1 <5>[ 4.833521] Loading compiled-in X.509 certificates <6>[ 4.843856] Demotion targets for Node 0: null <6>[ 4.851043] fsl-edma 22c0000.dma-controller: Adding to iommu group 6 <6>[ 4.858894] pcieport 0001:00:00.0: Adding to iommu group 7 <6>[ 4.864885] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.871216] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.877360] pcieport 0002:00:00.0: Adding to iommu group 8 <6>[ 4.883370] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.889674] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.898416] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.928436] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.951149] mmc0: new HS400 MMC card at address 0001 <6>[ 4.956844] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.962825] mmcblk0: p1 p2 <6>[ 4.966377] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.972591] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.978776] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 5.137591] hub 3-1:1.0: USB hub found <6>[ 5.141816] hub 3-1:1.0: 7 ports detected <6>[ 17.200599] clk: Disabling unused clocks <6>[ 17.204976] PM: genpd: Disabling unused power domains <6>[ 17.210367] ALSA device list: <6>[ 17.213648] No soundcards found. <6>[ 17.226421] Freeing unused kernel memory: 10240K <6>[ 17.231534] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 17.299509] udevd[106]: starting version 3.2.9 <5>[ 18.428425] random: crng init done <27>[ 18.434941] udevd[106]: specified user 'tss' unknown <27>[ 18.440344] udevd[106]: specified group 'tss' unknown <30>[ 18.446747] udevd[107]: starting eudev-3.2.9 <6>[ 18.704201] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 18.761189] NET: Registered PF_INET6 protocol family <4>[ 18.761278] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 18.787713] fsl_ddr_edac acquired irq 108 for MC <4>[ 18.793576] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 18.801164] fsl_ddr_edac MC err registered <6>[ 18.808699] Segment Routing with IPv6 <6>[ 18.812871] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 18.816479] In-situ OAM (IOAM) with IPv6 <3>[ 18.824921] thermal_sys: Thermal zone name (core-cluster-thermal) too long, should be under 20 chars <4>[ 18.836681] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 18.843314] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 18.868606] at24 1-0057: supply vcc not found, using dummy regulator <3>[ 18.878155] thermal_sys: Failed to register thermal zone core-cluster-thermal: -22 <6>[ 18.887252] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 18.903408] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 18.911424] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 18.917817] qoriq_thermal 1f80000.tmu: Failed to register sensors <4>[ 18.924851] at24 2-0050: supply vcc not found, using dummy regulator <3>[ 18.931909] qoriq_thermal 1f80000.tmu: probe with driver qoriq_thermal failed with error -22 <6>[ 18.941116] rtc-rv8803 0-0032: registered as rtc0 <4>[ 18.946793] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 18.954483] wm8904 2-001a: supply AVDD not found, using dummy regulator <6>[ 18.962597] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.970174] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 18.976929] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <4>[ 18.985412] wm8904 2-001a: supply CPVDD not found, using dummy regulator <6>[ 19.002569] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <4>[ 19.016074] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 19.050720] CAN device driver interface <6>[ 19.057729] input: buttons1 as /devices/platform/buttons1/input/input9 <6>[ 19.091855] wm8904 2-001a: revision A <6>[ 19.131357] usbcore: registered new device driver onboard-usb-dev <6>[ 19.141389] ftm-alarm 2800000.rtc: registered as rtc1 <6>[ 19.142085] caam 8000000.crypto: Entropy delay = 3200 <6>[ 19.157041] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 19.167114] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 19.172696] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 19.180305] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 19.224183] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 19.232917] mali-dp f080000.display: Adding to iommu group 9 <6>[ 19.240184] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <4>[ 19.249479] sysfs: cannot create duplicate filename '/devices/platform/sound/sai-tx-rx-wm8904-hifi' <4>[ 19.259013] CPU: 0 UID: 0 PID: 28 Comm: kworker/u8:1 Not tainted 6.11.0-rc5 #1 <4>[ 19.266529] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT) <4>[ 19.275084] Workqueue: events_unbound deferred_probe_work_func <4>[ 19.281210] Call trace: <4>[ 19.283921] dump_backtrace+0x94/0xec <4>[ 19.287861] show_stack+0x18/0x24 <4>[ 19.291450] dump_stack_lvl+0x78/0x90 <4>[ 19.295387] dump_stack+0x18/0x24 <4>[ 19.298973] sysfs_warn_dup+0x64/0x80 <4>[ 19.302911] sysfs_create_dir_ns+0xec/0x10c <4>[ 19.307369] kobject_add_internal+0x98/0x26c <4>[ 19.311915] kobject_add+0x9c/0x10c <4>[ 19.315674] device_add+0xc0/0x790 <4>[ 19.319346] device_register+0x20/0x30 <4>[ 19.323367] snd_soc_add_pcm_runtimes+0x328/0x850 <4>[ 19.328349] snd_soc_bind_card+0x2d4/0xbac <4>[ 19.332717] snd_soc_register_card+0xf0/0x108 <4>[ 19.337349] devm_snd_soc_register_card+0x4c/0xa4 <4>[ 19.342330] simple_probe+0x21c/0x3e8 [snd_soc_simple_card] <4>[ 19.348187] platform_probe+0x68/0xc0 <4>[ 19.352124] really_probe+0xbc/0x298 <4>[ 19.355971] __driver_probe_device+0x78/0x12c <4>[ 19.360603] driver_probe_device+0xd8/0x15c <4>[ 19.365061] __device_attach_driver+0xb8/0x134 <4>[ 19.369780] bus_for_each_drv+0x84/0xe0 <4>[ 19.373888] __device_attach+0x9c/0x188 <4>[ 19.377997] device_initial_probe+0x14/0x20 <4>[ 19.382455] bus_probe_device+0xac/0xb0 <4>[ 19.386563] deferred_probe_work_func+0x88/0xc0 <4>[ 19.391369] process_one_work+0x14c/0x28c <4>[ 19.395651] worker_thread+0x2cc/0x3d4 <4>[ 19.399671] kthread+0x114/0x118 <4>[ 19.403171] ret_from_fork+0x10/0x20 <3>[ 19.407858] kobject: kobject_add_internal failed for sai-tx-rx-wm8904-hifi with -EEXIST, don't try to register things with the same name in the same directory. <6>[ 19.415663] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <3>[ 19.422749] asoc-simple-card sound: probe with driver asoc-simple-card failed with error -12 <6>[ 19.442924] caam_jr 8010000.jr: Adding to iommu group 10 <6>[ 19.464679] caam algorithms registered in /proc/crypto <6>[ 19.470178] caam 8000000.crypto: registering rng-caam <6>[ 19.475642] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.482833] caam_jr 8020000.jr: Adding to iommu group 11 <6>[ 19.489094] caam_jr 8030000.jr: Adding to iommu group 12 <6>[ 19.495309] caam_jr 8040000.jr: Adding to iommu group 13 done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-491625/environment . /lava-491625/environment / # /lava-491625/bin/lava-test-runner /lava-491625/0 /lava-491625/bin/lava-test-runner /lava-491625/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 20.086863] d /lava-491625/0/tests/0_dmesg + cat uuid + UUID=491625_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 20.107791] <8>[ 20.129193] <8>[ 20.150666] + set +x <8>[ 20.160472] / # <0>[�