connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='default', state=, avail=True, host='nuc-1', port=41191, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:41191 connected to 192.168.0.1 (port 41191) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.214 (7 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3895378/tftp-deploy-ayh1m6la/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3895378/tftp-deploy-ayh1m6la/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### 2.9 MiB/s done Bytes transferred = 10707456 (a36200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3895378/tftp-deploy-ayh1m6la/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3895378/tftp-deploy-ayh1m6la/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 2.8 MiB/s done Bytes transferred = 17519264 (10b52a0 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3895378/tftp-deploy-ayh1m6la/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3895378/tftp-deploy-ayh1m6la/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *###### 2.8 MiB/s done Bytes transferred = 73434 (11eda hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0xa36200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17519200 Bytes = 16.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f94ed9 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.11.0-rc5 (KernelCI@build-j302956-arm-gcc-12-multi-v7-defconfig-config-thumb2-vch7w) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Aug 31 05:25:45 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: legacy bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40332 r8192 d21108 u69632 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524032 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.000001] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.008583] Switching to timer-based delay loop, resolution 83ns <6>[ 0.015690] Console: colour dummy device 80x30 <6>[ 0.020621] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.031649] CPU: Testing write buffer coherency: ok <6>[ 0.037020] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.042632] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.049487] pid_max: default: 32768 minimum: 301 <6>[ 0.054702] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.062555] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <3>[ 0.071661] /cpus/cpu@0 missing clock-frequency property <3>[ 0.077483] /cpus/cpu@1 missing clock-frequency property <3>[ 0.083325] /cpus/cpu@2 missing clock-frequency property <3>[ 0.089143] /cpus/cpu@3 missing clock-frequency property <6>[ 0.094946] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.101996] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.111264] rcu: Hierarchical SRCU implementation. <6>[ 0.116499] rcu: Max phase no-delay instances is 1000. <6>[ 0.122475] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.133454] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.142486] EFI services will not be available. <6>[ 0.147753] smp: Bringing up secondary CPUs ... <6>[ 0.153413] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.153432] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.170461] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.170480] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.187522] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.187541] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.203906] smp: Brought up 1 node, 4 CPUs <6>[ 0.208449] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.215127] CPU: All CPU(s) started in SVC mode. <6>[ 0.220763] Memory: 1967988K/2096128K available (11264K kernel code, 2540K rwdata, 6736K rodata, 2048K init, 430K bss, 59368K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.237595] devtmpfs: initialized <6>[ 0.257944] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.266389] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.276880] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.285741] pinctrl core: initialized pinctrl subsystem <6>[ 0.295323] DMI not present or invalid. <6>[ 0.300304] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.308851] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.319835] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.319893] cpuidle: using governor menu <6>[ 0.345250] platform 70000868.pinmux: Fixed dependency cycle(s) with /pinmux@70000868/pinmux <6>[ 0.381549] No ATAGs? <6>[ 0.384293] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.392881] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.415336] Serial: AMBA PL011 UART driver <3>[ 0.421238] tegra-mc 70019000.memory-controller: ppcsahbslvr: secure read @0x7fd41100: EMEM address decode error (EMEM decode error) <6>[ 0.453305] iommu: Default domain type: Translated <6>[ 0.458591] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.467233] SCSI subsystem initialized <6>[ 0.474448] usbcore: registered new interface driver usbfs <6>[ 0.480453] usbcore: registered new interface driver hub <6>[ 0.486308] usbcore: registered new device driver usb <6>[ 0.493578] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.499025] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.508796] PTP clock support registered <6>[ 0.513675] EDAC MC: Ver: 3.0.0 <6>[ 0.517580] scmi_core: SCMI protocol bus registered <6>[ 0.525334] vgaarb: loaded <6>[ 0.531662] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.551695] NET: Registered PF_INET protocol family <6>[ 0.557232] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.566706] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.575697] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.584026] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.592433] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.600518] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.607470] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.614670] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.622431] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.629002] RPC: Registered named UNIX socket transport module. <6>[ 0.635446] RPC: Registered udp transport module. <6>[ 0.640595] RPC: Registered tcp transport module. <6>[ 0.645761] RPC: Registered tcp-with-tls transport module. <6>[ 0.651732] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.658699] PCI: CLS 0 bytes, default 64 <5>[ 0.664404] Initialise system trusted keyrings <6>[ 0.669503] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.676726] Trying to unpack rootfs image as initramfs... <6>[ 0.676956] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.692168] NFS: Registering the id_resolver key type <5>[ 0.697727] Key type id_resolver registered <5>[ 0.702370] Key type id_legacy registered <6>[ 0.706840] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.714094] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.722421] Key type asymmetric registered <5>[ 0.726957] Asymmetric key parser 'x509' registered <6>[ 0.732420] bounce: pool size: 64 pages <6>[ 0.736717] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.744697] io scheduler mq-deadline registered <6>[ 0.749679] io scheduler kyber registered <6>[ 0.754155] io scheduler bfq registered <4>[ 0.814095] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.858060] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 0.879318] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 0.955831] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.968272] printk: legacy console [ttyS0] disabled <6>[ 0.974050] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 70, base_baud = 25500000) is a Tegra <6>[ 0.983599] printk: legacy console [ttyS0] enabled <6>[ 0.983599] printk: legacy console [ttyS0] enabled <6>[ 0.993886] printk: legacy bootconsole [uart0] disabled <6>[ 0.993886] printk: legacy bootconsole [uart0] disabled <6>[ 1.007038] msm_serial: driver initialized <6>[ 1.011892] SuperH (H)SCI(F) driver initialized <6>[ 1.017054] STMicroelectronics ASC driver initialized <6>[ 1.022541] STM32 USART driver initialized <6>[ 1.028022] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 71, base_baud = 0) is a TEGRA_UART <6>[ 1.038033] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 72, base_baud = 0) is a TEGRA_UART <6>[ 1.053986] tegra-host1x 50000000.host1x: Adding to iommu group 0 <6>[ 1.070856] tegra-vic 54340000.vic: Adding to iommu group 1 <6>[ 1.090269] brd: module loaded <6>[ 1.100406] loop: module loaded <3>[ 1.163251] spi spi1.0: Invalid delay unit 2, should be SPI_DELAY_UNIT_SCK <3>[ 1.170393] spi-tegra114 7000da00.spi: can't setup spi1.0, status -22 <3>[ 1.177139] spi_master spi1: spi_device register error /spi@7000da00/flash@0 <4>[ 1.184496] spi_master spi1: Failed to create SPI device for /spi@7000da00/flash@0 <6>[ 1.198540] CAN device driver interface <6>[ 1.204055] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.211474] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.216727] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.222975] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.228631] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.240365] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.246270] usbcore: registered new interface driver pegasus <6>[ 1.252244] usbcore: registered new interface driver asix <6>[ 1.257933] usbcore: registered new interface driver ax88179_178a <6>[ 1.264339] usbcore: registered new interface driver cdc_ether <6>[ 1.270463] usbcore: registered new interface driver smsc75xx <6>[ 1.276515] usbcore: registered new interface driver smsc95xx <6>[ 1.282577] usbcore: registered new interface driver net1080 <6>[ 1.288525] usbcore: registered new interface driver cdc_subset <6>[ 1.294756] usbcore: registered new interface driver zaurus <6>[ 1.300637] usbcore: registered new interface driver cdc_ncm <4>[ 1.307128] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 1.315588] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 1.328968] usbcore: registered new interface driver usb-storage <6>[ 1.397016] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 1.402207] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 1.461679] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.10 <6>[ 1.468233] hub 1-0:1.0: USB hub found <6>[ 1.472304] hub 1-0:1.0: 1 port detected <6>[ 1.482645] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 1.488052] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 1.495241] i2c_dev: i2c /dev entries driver <4>[ 1.508542] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 1.516298] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 1.569266] i2c 4-0040: Fixed dependency cycle(s) with /i2c@7000d000/pmic@40/pinmux <6>[ 1.578233] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 1.594315] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 1.600419] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:16 UTC (946684816) <6>[ 1.609322] as3722-rtc as3722-rtc: RTC interrupt 101 <4>[ 1.626513] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 1.633484] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 1.636087] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 1.646757] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 1.662960] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 1.675305] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.681779] sdhci: Copyright(c) Pierre Ossman <6>[ 1.688849] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.697279] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.708078] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 1.713116] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 1.713917] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.727197] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 1.727387] usbcore: registered new interface driver usbhid <6>[ 1.735579] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 1.740100] usbhid: USB HID core driver <6>[ 1.750944] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <3>[ 1.758242] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 1.760856] tegra-emc 7001b000.external-memory-controller: 64bit DRAM bus <3>[ 1.764234] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 1.774000] tegra-emc 7001b000.external-memory-controller: OPP HW ver. 0x2, current clock rate 924 MHz <4>[ 1.790494] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 1.791894] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <6>[ 1.809677] NET: Registered PF_INET6 protocol family <6>[ 1.815938] Segment Routing with IPv6 <6>[ 1.819940] In-situ OAM (IOAM) with IPv6 <6>[ 1.824236] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.831059] NET: Registered PF_PACKET protocol family <6>[ 1.836389] can: controller area network core <6>[ 1.841048] NET: Registered PF_CAN protocol family <6>[ 1.846118] can: raw protocol <6>[ 1.849350] can: broadcast manager protocol <6>[ 1.853810] can: netlink gateway - max_hops=1 <5>[ 1.858814] Key type dns_resolver registered <6>[ 1.864874] ThumbEE CPU extension supported. <5>[ 1.869414] Registering SWP/SWPB emulation handler <5>[ 1.887240] Loading compiled-in X.509 certificates <3>[ 1.938732] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3run <6>[ 1.947167] reg-fixed-voltage regulator-5v0sata: nonexclusive access to GPIO for (default) <6>[ 1.949818] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 1.962565] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 1.970949] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 1.979365] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 1.987769] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 1.996345] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.007073] tegra-dc 54200000.dc: Adding to iommu group 1 <4>[ 2.012930] Failed to attached device 54200000.dc to IOMMU_mapping <6>[ 2.021050] tegra-dc 54240000.dc: Adding to iommu group 1 <4>[ 2.026877] Failed to attached device 54240000.dc to IOMMU_mapping <6>[ 2.033647] Freeing initrd memory: 17112K <6>[ 2.062402] ci_hdrc ci_hdrc.2: EHCI Host Controller <6>[ 2.067569] ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2 <6>[ 2.075932] mmc0: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 2.121829] ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.10 <6>[ 2.128741] hub 2-0:1.0: USB hub found <6>[ 2.133037] hub 2-0:1.0: 1 port detected <6>[ 2.145254] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.148965] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.150283] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 2.157077] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <4>[ 2.164041] as3722-regulator as3722-regulator: DMA mask not set <6>[ 2.170413] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.184992] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <3>[ 2.190234] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 2.193402] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.200649] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 2.207890] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.215988] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <3>[ 2.220849] tegra-pcie 1003000.pcie: failed to get PHY#0: -517 <6>[ 2.228627] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <3>[ 2.232562] tegra-pcie 1003000.pcie: failed to get PHYs: -517 <3>[ 2.232580] tegra-pcie 1003000.pcie: failed to request resources: -517 <6>[ 2.240700] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 2.261242] mmc0: new high speed MMC card at address 0001 <6>[ 2.265964] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 2.278625] mmcblk0: mmc0:0001 SEM16G 14.7 GiB <4>[ 2.279737] usb2-0: supply vbus not found, using dummy regulator <4>[ 2.289833] usb2-1: supply vbus not found, using dummy regulator <6>[ 2.298190] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.302545] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.305017] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.309956] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 2.318271] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.331550] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.339937] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.348400] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 2.354873] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 2.355789] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 2.368160] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 2.369664] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 2.374879] mmcblk0boot0: mmc0:0001 SEM16G 4.00 MiB <6>[ 2.384953] mmcblk0boot1: mmc0:0001 SEM16G 4.00 MiB <6>[ 2.390671] mmcblk0rpmb: mmc0:0001 SEM16G 4.00 MiB, chardev (236:0) <6>[ 2.399865] mmc1: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 2.826201] mmc1: new high speed SD card at address 0260 <6>[ 2.833422] mmcblk1: mmc1:0260 1232 961 MiB <6>[ 2.841787] mmcblk1: p1 p2 <6>[ 3.587897] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 3.599173] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 3.605875] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 3.611801] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 3.619025] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 3.625626] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 3.632929] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 3.642237] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 PCIe Root Port <4>[ 3.649897] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 3.660035] pci 0000:00:02.0: PCI bridge to [bus 00] <6>[ 3.665449] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff] <6>[ 3.672043] pci 0000:00:02.0: enabling Extended Tags <6>[ 3.677537] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.701491] PCI: bus0: Fast back to back transfers disabled <6>[ 3.707535] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 3.716621] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint <6>[ 3.724345] pci 0000:01:00.0: BAR 0 [io 0x0000-0x00ff] <6>[ 3.729979] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00000fff 64bit] <6>[ 3.736884] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00003fff 64bit pref] <6>[ 3.744578] pci 0000:01:00.0: supports D1 D2 <6>[ 3.749178] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.781689] PCI: bus1: Fast back to back transfers disabled <6>[ 3.787515] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.794396] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]: assigned <6>[ 3.802162] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref]: assigned <6>[ 3.810857] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]: assigned <6>[ 3.817921] pci 0000:01:00.0: BAR 4 [mem 0x20000000-0x20003fff 64bit pref]: assigned <6>[ 3.825963] pci 0000:01:00.0: BAR 2 [mem 0x13000000-0x13000fff 64bit]: assigned <6>[ 3.833576] pci 0000:01:00.0: BAR 0 [io 0x1000-0x10ff]: assigned <6>[ 3.839935] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 3.845174] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 3.851528] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 3.858587] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <6>[ 3.866616] pci_bus 0000:00: resource 4 [mem 0x01000000-0x01001fff] <6>[ 3.873162] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] <6>[ 3.878996] pci_bus 0000:00: resource 6 [mem 0x13000000-0x1fffffff] <6>[ 3.885535] pci_bus 0000:00: resource 7 [mem 0x20000000-0x3fffffff pref] <6>[ 3.892513] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] <6>[ 3.898345] pci_bus 0000:01: resource 1 [mem 0x13000000-0x130fffff] <6>[ 3.904895] pci_bus 0000:01: resource 2 [mem 0x20000000-0x200fffff 64bit pref] <4>[ 3.912416] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 3.919699] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 3.926152] pcieport 0000:00:02.0: PME: Signaling with IRQ 127 <6>[ 3.932523] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 4.001359] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 130 <6>[ 4.009781] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <4>[ 4.019873] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 4.027873] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 4.035797] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 4.044866] tegra-ahci 70027000.sata: AHCI vers 0001.0301, 32 command slots, 3 Gbps, platform mode <6>[ 4.054087] tegra-ahci 70027000.sata: 1/2 ports implemented (port mask 0x1) <6>[ 4.061310] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 4.071625] scsi host0: tegra-ahci <6>[ 4.075889] scsi host1: tegra-ahci <6>[ 4.079671] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 131 lpm-pol 0 <6>[ 4.088818] ata2: DUMMY <6>[ 4.092034] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.424317] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 4.435239] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 4.444821] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 4.491888] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC) <6>[ 4.662563] r8169 0000:01:00.0 eth0: Link is Down <6>[ 6.245191] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <5>[ 6.281724] Sending DHCP requests ., OK <6>[ 6.326410] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.214 <6>[ 6.334454] IP-Config: Complete: <6>[ 6.337945] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.214, mask=255.255.255.0, gw=192.168.0.254 <6>[ 6.348579] host=192.168.0.214, domain=shed, nis-domain=(none) <6>[ 6.355143] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 6.355163] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 6.369130] clk: Disabling unused clocks <6>[ 6.373669] PM: genpd: Disabling unused power domains <6>[ 6.380359] Freeing unused kernel image (initmem) memory: 2048K <6>[ 6.386724] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.448310] udevd[144]: starting version 3.2.9 <5>[ 11.751671] random: crng init done <27>[ 11.757982] udevd[144]: specified user 'tss' unknown <27>[ 11.763404] udevd[144]: specified group 'tss' unknown <30>[ 11.769733] udevd[146]: starting eudev-3.2.9 <6>[ 11.905831] r8169 0000:01:00.0 enp1s0: renamed from eth0 (while UP) <6>[ 11.911747] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <4>[ 11.941072] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 11.951146] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 11.957702] tegra-xusb 70090000.usb: failed to request firmware: -2 <6>[ 11.957919] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 101000 mC <3>[ 11.964300] tegra-xusb 70090000.usb: probe with driver tegra-xusb failed with error -2 <6>[ 11.974032] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 101000 mC <6>[ 12.014980] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 101000 mC <6>[ 12.024817] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 101000 mC <6>[ 12.035457] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC <6>[ 12.047913] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 101000 mC <6>[ 12.088837] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 12.159001] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub done Saving random seed: <6>[ 12.465569] input: NVIDIA Tegra Jetson TK1 Headphones Jack as /devices/soc0/sound/sound/card1/input2 OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3895378/environment / # /lava-3895378/bin/lava-test-runner /lava-3895378/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3895378/0/tests/0_dmesg + cat uuid + UUID=3895378_1<8>[ 13.127316] .5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.158418] <8>[ 13.185537] <8>[ 13.213135] + set +x <8>[ 13.222907] / #