connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='default', state=, avail=True, host='nuc-1', port=37133, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:37133 connected to 192.168.0.1 (port 37133) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no U-Boot> setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff U-Boot> dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 DHCP client bound to address 192.168.0.136 U-Boot> setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 3895236/tftp-deploy-bayzd5jc/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895236/tftp-deploy-bayzd5jc/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# # 3.1 MiB/s done Bytes transferred = 5726976 (576300 hex) U-Boot> tftp 0x23000000 3895236/tftp-deploy-bayzd5jc/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895236/tftp-deploy-bayzd5jc/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### 3.2 MiB/s done Bytes transferred = 8800201 (8647c9 hex) U-Boot> setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 3895236/tftp-deploy-bayzd5jc/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895236/tftp-deploy-bayzd5jc/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *### 2.9 MiB/s done Bytes transferred = 36163 (8d43 hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0x576300 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 8800137 Bytes = 8.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200bd42 Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 6.11.0-rc5 (KernelCI@build-j303016-arm-gcc-12-sama7-defconfig-f4wc7) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 Sat Aug 31 04:58:12 UTC 2024 CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Atmel SAMA5D4 Xplained earlycon: atmel_serial0 at MMIO 0xfc00c000 (options '115200n8') printk: legacy bootconsole [atmel_serial0] enabled Memory policy: Data cache writeback cma: Reserved 64 MiB at 0x3c000000 on node -1 Zone ranges: Normal [mem 0x0000000020000000-0x000000003fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000020000000-0x000000003fffffff] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff] CPU: All CPU(s) started in SVC mode. Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>Built 1 zonelists, mobility grouping on. Total pages: 131072 <6>mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <2>timer_probe: no matching timers found <6>Console: colour dummy device 80x30 <6>sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns