connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='default', state=, avail=True, host='nuc-1', port=37133, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:37133 connected to 192.168.0.1 (port 37133) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no U-Boot> setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff U-Boot> dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 DHCP client bound to address 192.168.0.136 U-Boot> setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 3895598/tftp-deploy-n4lv8hw7/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895598/tftp-deploy-n4lv8hw7/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################################### 3.3 MiB/s done Bytes transferred = 11964928 (b69200 hex) U-Boot> tftp 0x23000000 3895598/tftp-deploy-n4lv8hw7/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895598/tftp-deploy-n4lv8hw7/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################### 3.1 MiB/s done Bytes transferred = 18525285 (11aac65 hex) U-Boot> setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 3895598/tftp-deploy-n4lv8hw7/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895598/tftp-deploy-n4lv8hw7/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *### 2.3 MiB/s done Bytes transferred = 36163 (8d43 hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0xb69200 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 18525221 Bytes = 17.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200bd42 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.11.0-rc5 (KernelCI@build-j303495-arm-clang-15-multi-v7-defconfig-5pb5s) (Debian clang version 15.0.7, Debian LLD 15.0.7) #1 SMP Sat Aug 31 23:07:00 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Atmel SAMA5D4 Xplained [ 0.000000] earlycon: atmel_serial0 at MMIO 0xfc00c000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu s40268 r8192 d21172 u69632 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x06020000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: timer@fc024000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 173750949719 ns <6>[ 0.000004] sched_clock: 32 bits at 11MHz, resolution 90ns, wraps every 195225786322ns <6>[ 0.008131] Switching to timer-based delay loop, resolution 90ns <6>[ 0.015441] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 10859434279 ns <6>[ 0.028908] Console: colour dummy device 80x30 <6>[ 0.033689] Calibrating delay loop (skipped), value calculated using timer frequency.. 22.00 BogoMIPS (lpj=110000) <6>[ 0.044295] CPU: Testing write buffer coherency: ok <6>[ 0.049427] pid_max: default: 32768 minimum: 301 <6>[ 0.054689] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.062258] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.072435] CPU0: thread -1, cpu 0, socket -1, mpidr c0000000 <6>[ 0.081929] Setting up static identity map for 0x20300000 - 0x203000ac <6>[ 0.091629] rcu: Hierarchical SRCU implementation. <6>[ 0.096595] rcu: Max phase no-delay instances is 1000. <6>[ 0.108554] EFI services will not be available. <6>[ 0.113989] smp: Bringing up secondary CPUs ... <6>[ 0.118734] smp: Brought up 1 node, 1 CPU <6>[ 0.123134] SMP: Total of 1 processors activated (22.00 BogoMIPS). <6>[ 0.129478] CPU: All CPU(s) started in SVC mode. <6>[ 0.134685] Memory: 404632K/524288K available (17408K kernel code, 2536K rwdata, 6644K rodata, 2048K init, 432K bss, 52540K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.151157] devtmpfs: initialized <6>[ 0.168744] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>[ 0.177305] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.187442] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.201761] pinctrl core: initialized pinctrl subsystem <6>[ 0.213485] DMI not present or invalid. <6>[ 0.220676] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.231638] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.244710] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.244967] cpuidle: using governor menu <6>[ 0.309495] AT91: PM: standby: standby, suspend: standby <6>[ 0.315120] No ATAGs? <6>[ 0.317746] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.326040] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.334222] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.344365] gpio-at91 fc06a000.gpio: at address (ptrval) <4>[ 0.350837] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.361045] gpio-at91 fc06b000.gpio: at address (ptrval) <4>[ 0.367340] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.377796] gpio-at91 fc06c000.gpio: at address (ptrval) <4>[ 0.384295] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.394795] gpio-at91 fc068000.gpio: at address (ptrval) <4>[ 0.401306] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.411972] gpio-at91 fc06d000.gpio: at address (ptrval) <6>[ 0.419813] pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver <6>[ 0.443161] Serial: AMBA PL011 UART driver <6>[ 0.496584] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.507810] at_xdmac f0014000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.534372] AT91: Detected SoC family: sama5d4 <6>[ 0.538989] AT91: Detected SoC: sama5d44, revision 0 <6>[ 0.550622] iommu: Default domain type: Translated <6>[ 0.555588] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.582625] SCSI subsystem initialized <6>[ 0.601253] usbcore: registered new interface driver usbfs <6>[ 0.606993] usbcore: registered new interface driver hub <6>[ 0.612703] usbcore: registered new device driver usb <6>[ 0.621732] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.626872] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.636431] PTP clock support registered <6>[ 0.660742] EDAC MC: Ver: 3.0.0 <6>[ 0.671133] scmi_core: SCMI protocol bus registered <6>[ 0.695285] vgaarb: loaded <6>[ 0.700894] clocksource: Switched to clocksource timer@fc024000 <6>[ 0.806638] NET: Registered PF_INET protocol family <6>[ 0.812391] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.822703] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.831395] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.839336] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.847492] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.855198] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.862036] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.868803] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.876488] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.912146] RPC: Registered named UNIX socket transport module. <6>[ 0.918259] RPC: Registered udp transport module. <6>[ 0.923337] RPC: Registered tcp transport module. <6>[ 0.928204] RPC: Registered tcp-with-tls transport module. <6>[ 0.934040] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.940705] PCI: CLS 0 bytes, default 64 <5>[ 0.947942] Initialise system trusted keyrings <6>[ 0.974147] Trying to unpack rootfs image as initramfs... <6>[ 0.992571] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 1.000134] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.042837] NFS: Registering the id_resolver key type <5>[ 1.048219] Key type id_resolver registered <5>[ 1.052720] Key type id_legacy registered <6>[ 1.057011] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.063966] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 1.121826] Key type asymmetric registered <5>[ 1.126104] Asymmetric key parser 'x509' registered <6>[ 1.131696] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.139273] io scheduler mq-deadline registered <6>[ 1.144170] io scheduler kyber registered <6>[ 1.148442] io scheduler bfq registered <6>[ 2.155713] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 2.212020] msm_serial: driver initialized <6>[ 2.217286] SuperH (H)SCI(F) driver initialized <6>[ 2.222898] STMicroelectronics ASC driver initialized <6>[ 2.228459] STM32 USART driver initialized <5>[ 2.323527] random: crng init done <6>[ 2.452277] brd: module loaded <6>[ 2.515383] loop: module loaded <6>[ 2.524692] atmel_usart_serial.0.auto: ttyAT5 at MMIO 0xf8004000 (irq = 25, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 2.585555] atmel_usart_serial.1.auto: ttyAT0 at MMIO 0xfc00c000 (irq = 26, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 2.596383] printk: legacy console [ttyAT0] enabled <6>[ 2.596383] printk: legacy console [ttyAT0] enabled <6>[ 2.606612] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 2.606612] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 2.665552] atmel_usart_serial.2.auto: ttyAT1 at MMIO 0xfc010000 (irq = 27, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 2.780781] CAN device driver interface <6>[ 6.996569] Freeing initrd memory: 18092K <6>[ 7.084426] macb f8020000.ethernet eth0: Cadence GEM rev 0x00020120 at 0xf8020000 irq 28 (52:11:6d:6b:d5:8f) <6>[ 7.096571] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.105795] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.111105] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.117446] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.123159] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.141462] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 7.147404] usbcore: registered new interface driver pegasus <6>[ 7.153548] usbcore: registered new interface driver asix <6>[ 7.159274] usbcore: registered new interface driver ax88179_178a <6>[ 7.165824] usbcore: registered new interface driver cdc_ether <6>[ 7.172062] usbcore: registered new interface driver smsc75xx <6>[ 7.178129] usbcore: registered new interface driver smsc95xx <6>[ 7.184264] usbcore: registered new interface driver net1080 <6>[ 7.190244] usbcore: registered new interface driver cdc_subset <6>[ 7.196550] usbcore: registered new interface driver zaurus <6>[ 7.202576] usbcore: registered new interface driver cdc_ncm <6>[ 7.221510] atmel-ehci 600000.ehci: EHCI Host Controller <6>[ 7.227166] atmel-ehci 600000.ehci: new USB bus registered, assigned bus number 1 <6>[ 7.240013] atmel-ehci 600000.ehci: irq 30, io mem 0x00600000 <6>[ 7.270923] atmel-ehci 600000.ehci: USB 2.0 started, EHCI 1.00 <6>[ 7.279612] hub 1-0:1.0: USB hub found <6>[ 7.284020] hub 1-0:1.0: 3 ports detected <6>[ 7.294207] at91_ohci 500000.ohci: USB Host Controller <6>[ 7.299691] at91_ohci 500000.ohci: new USB bus registered, assigned bus number 2 <6>[ 7.308245] at91_ohci 500000.ohci: irq 30, io mem 0x00500000 <6>[ 7.387414] hub 2-0:1.0: USB hub found <6>[ 7.391797] hub 2-0:1.0: 3 ports detected <6>[ 7.400328] usbcore: registered new interface driver usb-storage <6>[ 7.422810] i2c_dev: i2c /dev entries driver <6>[ 7.440548] at91-reset fc068600.reset-controller: Starting after RTC wakeup <6>[ 7.464300] sama5d4_wdt fc068640.watchdog: initialized (timeout = 16 sec, nowayout = 0) <6>[ 7.489639] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.496245] sdhci: Copyright(c) Pierre Ossman <6>[ 7.506235] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.517297] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.533203] slot@0 enforce active low on GPIO handle <6>[ 7.538744] atmel_mci fc000000.mmc: version: 0x600 <6>[ 7.562953] atmel_mci fc000000.mmc: using dma0chan0 for DMA transfers <6>[ 7.584091] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 7.612134] usbcore: registered new interface driver usbhid <6>[ 7.618060] usbhid: USB HID core driver <6>[ 7.633298] atmel_mci fc000000.mmc: Atmel MCI controller at 0xfc000000 irq 31, 1 slots <6>[ 7.661154] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc <6>[ 7.667793] nand: Micron MT29F4G08ABAEAWP <6>[ 7.672163] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 <6>[ 7.711874] Bad block table found at page 131008, version 0x01 <6>[ 7.720497] Bad block table found at page 130944, version 0x01 <5>[ 7.727578] 7 fixed-partitions partitions found on MTD device atmel_nand <5>[ 7.734686] Creating 7 MTD partitions on "atmel_nand": <5>[ 7.740081] 0x000000000000-0x000000040000 : "at91bootstrap" <5>[ 7.749832] 0x000000040000-0x000000100000 : "bootloader" <5>[ 7.759231] 0x000000100000-0x000000140000 : "bootloader env redundant" <5>[ 7.769779] 0x000000140000-0x000000180000 : "bootloader env" <5>[ 7.779613] 0x000000180000-0x000000200000 : "device tree" <5>[ 7.788959] 0x000000200000-0x000000800000 : "kernel" <5>[ 7.797956] 0x000000800000-0x000020000000 : "rootfs" <6>[ 7.823325] NET: Registered PF_INET6 protocol family <6>[ 7.831872] Segment Routing with IPv6 <6>[ 7.835885] In-situ OAM (IOAM) with IPv6 <6>[ 7.840231] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.848124] NET: Registered PF_PACKET protocol family <6>[ 7.853574] can: controller area network core <6>[ 7.858303] NET: Registered PF_CAN protocol family <6>[ 7.863443] can: raw protocol <6>[ 7.866647] can: broadcast manager protocol <6>[ 7.871168] can: netlink gateway - max_hops=1 <5>[ 7.876664] Key type dns_resolver registered <6>[ 7.881752] ThumbEE CPU extension supported. <5>[ 7.886295] Registering SWP/SWPB emulation handler <5>[ 7.917273] Loading compiled-in X.509 certificates <6>[ 7.956173] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 8.043763] macb f8020000.ethernet eth0: PHY [f8020000.ethernet-ffffffff:01] driver [Micrel KSZ8081 or KSZ8091] (irq=29) <6>[ 8.056023] macb f8020000.ethernet eth0: configuring for phy/rmii link mode <6>[ 9.649246] macb f8020000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 9.680981] Sending DHCP requests ., OK <6>[ 9.725145] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.136 <6>[ 9.733270] IP-Config: Complete: <6>[ 9.736719] device=eth0, hwaddr=52:11:6d:6b:d5:8f, ipaddr=192.168.0.136, mask=255.255.255.0, gw=192.168.0.254 <6>[ 9.747422] host=192.168.0.136, domain=shed, nis-domain=(none) <6>[ 9.753973] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 9.753999] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 9.768381] clk: Disabling unused clocks <6>[ 9.772891] PM: genpd: Disabling unused power domains <6>[ 9.780040] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan2 for rx DMA transfers <6>[ 9.789779] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan3 for tx DMA transfers <6>[ 9.803924] Freeing unused kernel image (initmem) memory: 2048K <6>[ 9.810568] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.257201] udevd[75]: starting version 3.2.9 <27>[ 10.288346] udevd[75]: specified user 'tss' unknown <27>[ 10.294469] udevd[75]: specified group 'tss' unknown <30>[ 10.309039] udevd[76]: starting eudev-3.2.9 <6>[ 13.853692] at91_i2c f8014000.i2c: using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <4>[ 13.871589] mtdblock: MTD device 'at91bootstrap' is NAND, please consider using UBI block devices instead. <4>[ 13.905759] mtdblock: MTD device 'bootloader' is NAND, please consider using UBI block devices instead. <4>[ 13.922040] mtdblock: MTD device 'bootloader env redundant' is NAND, please consider using UBI block devices instead. <6>[ 13.939328] i2c i2c-0: using pinctrl states for GPIO recovery <6>[ 13.945729] i2c i2c-0: using generic GPIOs for recovery <6>[ 13.951495] at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502). <4>[ 13.997420] mtdblock: MTD device 'bootloader env' is NAND, please consider using UBI block devices instead. <4>[ 14.015573] mtdblock: MTD device 'device tree' is NAND, please consider using UBI block devices instead. <4>[ 14.095431] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. <4>[ 14.106190] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. <6>[ 14.687441] atmel_spi fc018000.spi: Using dma0chan6 (tx) and dma0chan7 (rx) for DMA transfers <6>[ 14.813557] iio iio:device0: Resolution used: 10 bits <6>[ 14.818863] iio iio:device0: ADC Touch screen is disabled. <6>[ 14.862962] atmel_spi fc018000.spi: Atmel SPI Controller version 0x221 at 0xfc018000 (irq 36) <6>[ 14.885683] atmel_aes fc044000.crypto: version: 0x201 <6>[ 14.904703] atmel_sha fc050000.crypto: version: 0x420 <6>[ 14.914571] atmel_tdes fc04c000.crypto: version: 0x702 <6>[ 14.955031] atmel_aes fc044000.crypto: Atmel AES - Using dma1chan0, dma1chan1 for DMA transfers <6>[ 15.023348] atmel_sha fc050000.crypto: using dma1chan2 for DMA transfers <6>[ 15.030362] atmel_sha fc050000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 15.101329] atmel_tdes fc04c000.crypto: using dma1chan3, dma1chan4 for DMA transfers <6>[ 15.109386] atmel_tdes fc04c000.crypto: Atmel DES/TDES <6>[ 15.272495] at91_rtc fc0686b0.rtc: registered as rtc0 <6>[ 15.277851] at91_rtc fc0686b0.rtc: setting system clock to 2012-01-01T00:00:30 UTC (1325376030) <6>[ 15.287042] at91_rtc fc0686b0.rtc: AT91 Real Time Clock driver. done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3895598/environment / # /lava-3895598/bin/lava-test-runner /lava-3895598/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3895598/0/tests/0_dmesg + cat uuid + UUID=3895598_1.5<8>[. 18.775432] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.902341] <8>[ 19.014850] <8>[ 19.127756] + set +x <8>[ 19.140749] / #