connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='default', state=, avail=True, host='nuc-1', port=37133, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:37133 connected to 192.168.0.1 (port 37133) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no U-Boot> setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff U-Boot> dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 DHCP client bound to address 192.168.0.136 U-Boot> setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 3895629/tftp-deploy-9hjp_ntu/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895629/tftp-deploy-9hjp_ntu/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################### 3.3 MiB/s done Bytes transferred = 11354624 (ad4200 hex) U-Boot> tftp 0x23000000 3895629/tftp-deploy-9hjp_ntu/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895629/tftp-deploy-9hjp_ntu/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 3.2 MiB/s done Bytes transferred = 17978514 (1125492 hex) U-Boot> setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 3895629/tftp-deploy-9hjp_ntu/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.136 Filename '3895629/tftp-deploy-9hjp_ntu/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *### 2.3 MiB/s done Bytes transferred = 36163 (8d43 hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0xad4200 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17978450 Bytes = 17.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200bd42 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.11.0-rc5 (KernelCI@build-j303542-arm-gcc-12-multi-v7-defconfig-vhqmp) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Aug 31 23:24:39 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Atmel SAMA5D4 Xplained [ 0.000000] earlycon: atmel_serial0 at MMIO 0xfc00c000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu s40332 r8192 d21108 u69632 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x06020000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: timer@fc024000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 173750949719 ns <6>[ 0.000004] sched_clock: 32 bits at 11MHz, resolution 90ns, wraps every 195225786322ns <6>[ 0.008139] Switching to timer-based delay loop, resolution 90ns <6>[ 0.015292] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 10859434279 ns <6>[ 0.028584] Console: colour dummy device 80x30 <6>[ 0.033364] Calibrating delay loop (skipped), value calculated using timer frequency.. 22.00 BogoMIPS (lpj=110000) <6>[ 0.043961] CPU: Testing write buffer coherency: ok <6>[ 0.049093] pid_max: default: 32768 minimum: 301 <6>[ 0.054349] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.061907] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.072077] CPU0: thread -1, cpu 0, socket -1, mpidr c0000000 <6>[ 0.081551] Setting up static identity map for 0x20300000 - 0x203000ac <6>[ 0.091056] rcu: Hierarchical SRCU implementation. <6>[ 0.096017] rcu: Max phase no-delay instances is 1000. <6>[ 0.107515] EFI services will not be available. <6>[ 0.112917] smp: Bringing up secondary CPUs ... <6>[ 0.117656] smp: Brought up 1 node, 1 CPU <6>[ 0.122047] SMP: Total of 1 processors activated (22.00 BogoMIPS). <6>[ 0.128386] CPU: All CPU(s) started in SVC mode. <6>[ 0.133585] Memory: 406188K/524288K available (16384K kernel code, 2540K rwdata, 6736K rodata, 2048K init, 430K bss, 50984K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.150146] devtmpfs: initialized <6>[ 0.166606] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>[ 0.175090] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.185212] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.199220] pinctrl core: initialized pinctrl subsystem <6>[ 0.210639] DMI not present or invalid. <6>[ 0.217809] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.228608] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.241528] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.241766] cpuidle: using governor menu <6>[ 0.303714] AT91: PM: standby: standby, suspend: standby <6>[ 0.309218] No ATAGs? <6>[ 0.312025] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.320321] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.328340] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.338434] gpio-at91 fc06a000.gpio: at address (ptrval) <4>[ 0.344855] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.354980] gpio-at91 fc06b000.gpio: at address (ptrval) <4>[ 0.361382] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.371641] gpio-at91 fc06c000.gpio: at address (ptrval) <4>[ 0.377926] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.388308] gpio-at91 fc068000.gpio: at address (ptrval) <4>[ 0.394775] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.405217] gpio-at91 fc06d000.gpio: at address (ptrval) <6>[ 0.413112] pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver <6>[ 0.435061] Serial: AMBA PL011 UART driver <6>[ 0.480502] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.491468] at_xdmac f0014000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.523199] AT91: Detected SoC family: sama5d4 <6>[ 0.527816] AT91: Detected SoC: sama5d44, revision 0 <6>[ 0.538609] iommu: Default domain type: Translated <6>[ 0.543678] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.572619] SCSI subsystem initialized <6>[ 0.581291] usbcore: registered new interface driver usbfs <6>[ 0.587024] usbcore: registered new interface driver hub <6>[ 0.592735] usbcore: registered new device driver usb <6>[ 0.601393] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.606526] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.616079] PTP clock support registered <6>[ 0.641470] EDAC MC: Ver: 3.0.0 <6>[ 0.650862] scmi_core: SCMI protocol bus registered <6>[ 0.674928] vgaarb: loaded <6>[ 0.691421] clocksource: Switched to clocksource timer@fc024000 <6>[ 0.763038] NET: Registered PF_INET protocol family <6>[ 0.768687] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.779092] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.787765] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.795752] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.803835] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.811471] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.818299] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.825140] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.832747] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.875256] RPC: Registered named UNIX socket transport module. <6>[ 0.881368] RPC: Registered udp transport module. <6>[ 0.886463] RPC: Registered tcp transport module. <6>[ 0.891313] RPC: Registered tcp-with-tls transport module. <6>[ 0.897128] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.903855] PCI: CLS 0 bytes, default 64 <5>[ 0.910843] Initialise system trusted keyrings <6>[ 0.936970] Trying to unpack rootfs image as initramfs... <6>[ 0.953121] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 0.960645] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.012873] NFS: Registering the id_resolver key type <5>[ 1.018288] Key type id_resolver registered <5>[ 1.022826] Key type id_legacy registered <6>[ 1.027114] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.034081] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 1.083266] Key type asymmetric registered <5>[ 1.087546] Asymmetric key parser 'x509' registered <6>[ 1.093105] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.100678] io scheduler mq-deadline registered <6>[ 1.105599] io scheduler kyber registered <6>[ 1.109845] io scheduler bfq registered <6>[ 2.116057] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 2.151114] msm_serial: driver initialized <6>[ 2.156605] SuperH (H)SCI(F) driver initialized <6>[ 2.161964] STMicroelectronics ASC driver initialized <6>[ 2.167660] STM32 USART driver initialized <5>[ 2.275353] random: crng init done <6>[ 2.393883] brd: module loaded <6>[ 2.466527] loop: module loaded <6>[ 2.475583] atmel_usart_serial.0.auto: ttyAT5 at MMIO 0xf8004000 (irq = 25, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 2.547227] atmel_usart_serial.1.auto: ttyAT0 at MMIO 0xfc00c000 (irq = 26, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 2.558000] printk: legacy console [ttyAT0] enabled <6>[ 2.558000] printk: legacy console [ttyAT0] enabled <6>[ 2.568192] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 2.568192] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 2.640349] atmel_usart_serial.2.auto: ttyAT1 at MMIO 0xfc010000 (irq = 27, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 2.750635] CAN device driver interface <6>[ 7.013256] Freeing initrd memory: 17560K <6>[ 7.101485] macb f8020000.ethernet eth0: Cadence GEM rev 0x00020120 at 0xf8020000 irq 28 (52:11:6d:6b:d5:8f) <6>[ 7.113516] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.122446] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.127658] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.134126] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.139771] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.157247] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 7.163342] usbcore: registered new interface driver pegasus <6>[ 7.169392] usbcore: registered new interface driver asix <6>[ 7.175198] usbcore: registered new interface driver ax88179_178a <6>[ 7.181609] usbcore: registered new interface driver cdc_ether <6>[ 7.187822] usbcore: registered new interface driver smsc75xx <6>[ 7.193946] usbcore: registered new interface driver smsc95xx <6>[ 7.200003] usbcore: registered new interface driver net1080 <6>[ 7.206039] usbcore: registered new interface driver cdc_subset <6>[ 7.212334] usbcore: registered new interface driver zaurus <6>[ 7.218256] usbcore: registered new interface driver cdc_ncm <6>[ 7.236597] atmel-ehci 600000.ehci: EHCI Host Controller <6>[ 7.242359] atmel-ehci 600000.ehci: new USB bus registered, assigned bus number 1 <6>[ 7.255391] atmel-ehci 600000.ehci: irq 30, io mem 0x00600000 <6>[ 7.282186] atmel-ehci 600000.ehci: USB 2.0 started, EHCI 1.00 <6>[ 7.290709] hub 1-0:1.0: USB hub found <6>[ 7.295076] hub 1-0:1.0: 3 ports detected <6>[ 7.305031] at91_ohci 500000.ohci: USB Host Controller <6>[ 7.310507] at91_ohci 500000.ohci: new USB bus registered, assigned bus number 2 <6>[ 7.319013] at91_ohci 500000.ohci: irq 30, io mem 0x00500000 <6>[ 7.398508] hub 2-0:1.0: USB hub found <6>[ 7.402855] hub 2-0:1.0: 3 ports detected <6>[ 7.411067] usbcore: registered new interface driver usb-storage <6>[ 7.432611] i2c_dev: i2c /dev entries driver <6>[ 7.449799] at91-reset fc068600.reset-controller: Starting after RTC wakeup <6>[ 7.472720] sama5d4_wdt fc068640.watchdog: initialized (timeout = 16 sec, nowayout = 0) <6>[ 7.497430] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.504031] sdhci: Copyright(c) Pierre Ossman <6>[ 7.513775] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.524614] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.539713] slot@0 enforce active low on GPIO handle <6>[ 7.545432] atmel_mci fc000000.mmc: version: 0x600 <6>[ 7.574052] atmel_mci fc000000.mmc: using dma0chan0 for DMA transfers <6>[ 7.585288] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 7.613553] usbcore: registered new interface driver usbhid <6>[ 7.619397] usbhid: USB HID core driver <6>[ 7.634650] atmel_mci fc000000.mmc: Atmel MCI controller at 0xfc000000 irq 31, 1 slots <6>[ 7.672010] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc <6>[ 7.678852] nand: Micron MT29F4G08ABAEAWP <6>[ 7.683178] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 <6>[ 7.713085] Bad block table found at page 131008, version 0x01 <6>[ 7.720675] Bad block table found at page 130944, version 0x01 <5>[ 7.731252] 7 fixed-partitions partitions found on MTD device atmel_nand <5>[ 7.738410] Creating 7 MTD partitions on "atmel_nand": <5>[ 7.743857] 0x000000000000-0x000000040000 : "at91bootstrap" <5>[ 7.753462] 0x000000040000-0x000000100000 : "bootloader" <5>[ 7.762809] 0x000000100000-0x000000140000 : "bootloader env redundant" <5>[ 7.773179] 0x000000140000-0x000000180000 : "bootloader env" <5>[ 7.782880] 0x000000180000-0x000000200000 : "device tree" <5>[ 7.791937] 0x000000200000-0x000000800000 : "kernel" <5>[ 7.800816] 0x000000800000-0x000020000000 : "rootfs" <6>[ 7.825032] NET: Registered PF_INET6 protocol family <6>[ 7.833436] Segment Routing with IPv6 <6>[ 7.837458] In-situ OAM (IOAM) with IPv6 <6>[ 7.841779] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.849603] NET: Registered PF_PACKET protocol family <6>[ 7.855041] can: controller area network core <6>[ 7.859758] NET: Registered PF_CAN protocol family <6>[ 7.864877] can: raw protocol <6>[ 7.868076] can: broadcast manager protocol <6>[ 7.872592] can: netlink gateway - max_hops=1 <5>[ 7.878040] Key type dns_resolver registered <6>[ 7.883114] ThumbEE CPU extension supported. <5>[ 7.887643] Registering SWP/SWPB emulation handler <5>[ 7.916113] Loading compiled-in X.509 certificates <6>[ 7.953983] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 8.045037] macb f8020000.ethernet eth0: PHY [f8020000.ethernet-ffffffff:01] driver [Micrel KSZ8081 or KSZ8091] (irq=29) <6>[ 8.057278] macb f8020000.ethernet eth0: configuring for phy/rmii link mode <6>[ 9.686948] macb f8020000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 9.742181] Sending DHCP requests ., OK <6>[ 9.786387] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.136 <6>[ 9.794498] IP-Config: Complete: <6>[ 9.797949] device=eth0, hwaddr=52:11:6d:6b:d5:8f, ipaddr=192.168.0.136, mask=255.255.255.0, gw=192.168.0.254 <6>[ 9.808676] host=192.168.0.136, domain=shed, nis-domain=(none) <6>[ 9.815233] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 9.815259] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 9.829573] clk: Disabling unused clocks <6>[ 9.834074] PM: genpd: Disabling unused power domains <6>[ 9.841160] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan2 for rx DMA transfers <6>[ 9.850861] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan3 for tx DMA transfers <6>[ 9.865971] Freeing unused kernel image (initmem) memory: 2048K <6>[ 9.872641] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.309870] udevd[75]: starting version 3.2.9 <27>[ 10.340598] udevd[75]: specified user 'tss' unknown <27>[ 10.346604] udevd[75]: specified group 'tss' unknown <30>[ 10.360069] udevd[76]: starting eudev-3.2.9 <6>[ 13.882697] at91_i2c f8014000.i2c: using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <4>[ 13.894988] mtdblock: MTD device 'at91bootstrap' is NAND, please consider using UBI block devices instead. <4>[ 13.905691] mtdblock: MTD device 'bootloader env redundant' is NAND, please consider using UBI block devices instead. <4>[ 13.956675] mtdblock: MTD device 'bootloader' is NAND, please consider using UBI block devices instead. <6>[ 13.968148] i2c i2c-0: using pinctrl states for GPIO recovery <6>[ 13.974483] i2c i2c-0: using generic GPIOs for recovery <6>[ 13.980134] at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502). <4>[ 14.004725] mtdblock: MTD device 'bootloader env' is NAND, please consider using UBI block devices instead. <4>[ 14.038279] mtdblock: MTD device 'device tree' is NAND, please consider using UBI block devices instead. <4>[ 14.126097] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. <4>[ 14.143428] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. <6>[ 14.663170] atmel_spi fc018000.spi: Using dma0chan6 (tx) and dma0chan7 (rx) for DMA transfers <6>[ 14.757192] iio iio:device0: Resolution used: 10 bits <6>[ 14.762652] iio iio:device0: ADC Touch screen is disabled. <6>[ 14.819111] atmel_aes fc044000.crypto: version: 0x201 <6>[ 14.842409] atmel_spi fc018000.spi: Atmel SPI Controller version 0x221 at 0xfc018000 (irq 36) <6>[ 14.863760] atmel_sha fc050000.crypto: version: 0x420 <6>[ 14.915821] atmel_tdes fc04c000.crypto: version: 0x702 <6>[ 14.924133] atmel_aes fc044000.crypto: Atmel AES - Using dma1chan0, dma1chan1 for DMA transfers <6>[ 14.993009] atmel_sha fc050000.crypto: using dma1chan2 for DMA transfers <6>[ 15.000020] atmel_sha fc050000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 15.131699] atmel_tdes fc04c000.crypto: using dma1chan3, dma1chan4 for DMA transfers <6>[ 15.139981] atmel_tdes fc04c000.crypto: Atmel DES/TDES <6>[ 15.213603] at91_rtc fc0686b0.rtc: registered as rtc0 <6>[ 15.218953] at91_rtc fc0686b0.rtc: setting system clock to 2012-01-01T00:00:30 UTC (1325376030) <6>[ 15.228101] at91_rtc fc0686b0.rtc: AT91 Real Time Clock driver. done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3895629/environment / # /lava-3895629/bin/lava-test-runner /lava-3895629/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3895629/0/tests/0_dmesg + cat uuid + UUID=3895629_1<8>[ . 18.711244] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.834499] <8>[ 18.944824] <8>[ 19.055760] + set +x <8>[ 19.068392] / #