connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='default', state=, avail=True, host='nuc-1', port=41191, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:41191 connected to 192.168.0.1 (port 41191) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.214 (8 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3895940/tftp-deploy-pkj2_gau/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3895940/tftp-deploy-pkj2_gau/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### 3 MiB/s done Bytes transferred = 10711552 (a37200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3895940/tftp-deploy-pkj2_gau/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3895940/tftp-deploy-pkj2_gau/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 2.9 MiB/s done Bytes transferred = 17518466 (10b4f82 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3895940/tftp-deploy-pkj2_gau/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3895940/tftp-deploy-pkj2_gau/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *###### 2.5 MiB/s done Bytes transferred = 73434 (11eda hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0xa37200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17518402 Bytes = 16.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f94ed9 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.11.0-rc6 (KernelCI@build-j304630-arm-gcc-12-multi-v7-defconfig-config-thumb2-j6qvz) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Sep 1 23:19:51 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: legacy bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40332 r8192 d21108 u69632 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524032 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.000001] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.008580] Switching to timer-based delay loop, resolution 83ns <6>[ 0.015690] Console: colour dummy device 80x30 <6>[ 0.020620] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.031647] CPU: Testing write buffer coherency: ok <6>[ 0.037020] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.042631] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.049487] pid_max: default: 32768 minimum: 301 <6>[ 0.054701] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.062556] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <3>[ 0.071664] /cpus/cpu@0 missing clock-frequency property <3>[ 0.077483] /cpus/cpu@1 missing clock-frequency property <3>[ 0.083323] /cpus/cpu@2 missing clock-frequency property <3>[ 0.089140] /cpus/cpu@3 missing clock-frequency property <6>[ 0.094941] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.101997] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.111262] rcu: Hierarchical SRCU implementation. <6>[ 0.116499] rcu: Max phase no-delay instances is 1000. <6>[ 0.122472] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.133451] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.142475] EFI services will not be available. <6>[ 0.147740] smp: Bringing up secondary CPUs ... <6>[ 0.153403] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.153422] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.170452] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.170471] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.187518] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.187536] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.203898] smp: Brought up 1 node, 4 CPUs <6>[ 0.208440] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.215118] CPU: All CPU(s) started in SVC mode. <6>[ 0.220757] Memory: 1967992K/2096128K available (11264K kernel code, 2540K rwdata, 6736K rodata, 2048K init, 430K bss, 59364K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.237593] devtmpfs: initialized <6>[ 0.257914] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.266359] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.276859] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.285704] pinctrl core: initialized pinctrl subsystem <6>[ 0.295287] DMI not present or invalid. <6>[ 0.300259] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.308856] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.319852] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.319911] cpuidle: using governor menu <6>[ 0.345206] platform 70000868.pinmux: Fixed dependency cycle(s) with /pinmux@70000868/pinmux <6>[ 0.381532] No ATAGs? <6>[ 0.384278] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.392865] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.415327] Serial: AMBA PL011 UART driver <3>[ 0.421256] tegra-mc 70019000.memory-controller: ppcsahbslvr: secure read @0x7fd41100: EMEM address decode error (EMEM decode error) <6>[ 0.449833] iommu: Default domain type: Translated <6>[ 0.455102] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.463829] SCSI subsystem initialized <6>[ 0.468448] usbcore: registered new interface driver usbfs <6>[ 0.474456] usbcore: registered new interface driver hub <6>[ 0.480308] usbcore: registered new device driver usb <6>[ 0.487557] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.493000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.502780] PTP clock support registered <6>[ 0.507442] EDAC MC: Ver: 3.0.0 <6>[ 0.511341] scmi_core: SCMI protocol bus registered <6>[ 0.519178] vgaarb: loaded <6>[ 0.529487] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.549014] NET: Registered PF_INET protocol family <6>[ 0.554564] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.564020] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.573009] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.581342] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.589734] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.597826] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.604768] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.611964] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.619716] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.626346] RPC: Registered named UNIX socket transport module. <6>[ 0.632790] RPC: Registered udp transport module. <6>[ 0.637943] RPC: Registered tcp transport module. <6>[ 0.643101] RPC: Registered tcp-with-tls transport module. <6>[ 0.649067] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.656037] PCI: CLS 0 bytes, default 64 <5>[ 0.661741] Initialise system trusted keyrings <6>[ 0.666822] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.674049] Trying to unpack rootfs image as initramfs... <6>[ 0.674260] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.686550] NFS: Registering the id_resolver key type <5>[ 0.692146] Key type id_resolver registered <5>[ 0.696767] Key type id_legacy registered <6>[ 0.701251] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.708494] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.716787] Key type asymmetric registered <5>[ 0.721350] Asymmetric key parser 'x509' registered <6>[ 0.726794] bounce: pool size: 64 pages <6>[ 0.731117] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.739081] io scheduler mq-deadline registered <6>[ 0.744081] io scheduler kyber registered <6>[ 0.748552] io scheduler bfq registered <4>[ 0.813405] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.857476] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 0.878684] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 0.953469] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.965882] printk: legacy console [ttyS0] disabled <6>[ 0.971662] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 70, base_baud = 25500000) is a Tegra <6>[ 0.981213] printk: legacy console [ttyS0] enabled <6>[ 0.981213] printk: legacy console [ttyS0] enabled <6>[ 0.991502] printk: legacy bootconsole [uart0] disabled <6>[ 0.991502] printk: legacy bootconsole [uart0] disabled <6>[ 1.009692] msm_serial: driver initialized <6>[ 1.014512] SuperH (H)SCI(F) driver initialized <6>[ 1.019747] STMicroelectronics ASC driver initialized <6>[ 1.025217] STM32 USART driver initialized <6>[ 1.030717] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 71, base_baud = 0) is a TEGRA_UART <6>[ 1.040737] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 72, base_baud = 0) is a TEGRA_UART <6>[ 1.066891] tegra-host1x 50000000.host1x: Adding to iommu group 0 <6>[ 1.083711] tegra-vic 54340000.vic: Adding to iommu group 1 <6>[ 1.107146] brd: module loaded <6>[ 1.117446] loop: module loaded <3>[ 1.172504] spi spi1.0: Invalid delay unit 2, should be SPI_DELAY_UNIT_SCK <3>[ 1.179696] spi-tegra114 7000da00.spi: can't setup spi1.0, status -22 <3>[ 1.186398] spi_master spi1: spi_device register error /spi@7000da00/flash@0 <4>[ 1.193770] spi_master spi1: Failed to create SPI device for /spi@7000da00/flash@0 <6>[ 1.207811] CAN device driver interface <6>[ 1.213314] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.220765] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.225988] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.232229] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.237886] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.249610] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.255479] usbcore: registered new interface driver pegasus <6>[ 1.261456] usbcore: registered new interface driver asix <6>[ 1.267147] usbcore: registered new interface driver ax88179_178a <6>[ 1.273561] usbcore: registered new interface driver cdc_ether <6>[ 1.279700] usbcore: registered new interface driver smsc75xx <6>[ 1.285736] usbcore: registered new interface driver smsc95xx <6>[ 1.291803] usbcore: registered new interface driver net1080 <6>[ 1.297752] usbcore: registered new interface driver cdc_subset <6>[ 1.303984] usbcore: registered new interface driver zaurus <6>[ 1.309891] usbcore: registered new interface driver cdc_ncm <4>[ 1.316362] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 1.324837] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 1.338196] usbcore: registered new interface driver usb-storage <6>[ 1.406868] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 1.412060] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 1.479507] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.10 <6>[ 1.486040] hub 1-0:1.0: USB hub found <6>[ 1.490126] hub 1-0:1.0: 1 port detected <6>[ 1.508084] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 1.513511] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 1.520700] i2c_dev: i2c /dev entries driver <4>[ 1.541950] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 1.549706] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 1.616980] i2c 4-0040: Fixed dependency cycle(s) with /i2c@7000d000/pmic@40/pinmux <6>[ 1.625971] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 1.642274] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 1.648405] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:16 UTC (946684816) <6>[ 1.657318] as3722-rtc as3722-rtc: RTC interrupt 101 <3>[ 1.658400] as3722-regulator as3722-regulator: regulator 2 register failed -517 <4>[ 1.682134] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 1.691614] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 1.698589] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 1.719971] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.726412] sdhci: Copyright(c) Pierre Ossman <6>[ 1.733507] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.741924] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.749896] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 1.754921] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 1.770024] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 1.779671] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.788641] usbcore: registered new interface driver usbhid <6>[ 1.794508] usbhid: USB HID core driver <6>[ 1.804944] tegra-emc 7001b000.external-memory-controller: 64bit DRAM bus <6>[ 1.814141] tegra-emc 7001b000.external-memory-controller: OPP HW ver. 0x2, current clock rate 924 MHz <6>[ 1.826821] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <6>[ 1.838649] NET: Registered PF_INET6 protocol family <6>[ 1.844944] Segment Routing with IPv6 <6>[ 1.848930] In-situ OAM (IOAM) with IPv6 <6>[ 1.853224] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.860073] NET: Registered PF_PACKET protocol family <6>[ 1.865387] can: controller area network core <6>[ 1.870070] NET: Registered PF_CAN protocol family <6>[ 1.875122] can: raw protocol <6>[ 1.878353] can: broadcast manager protocol <6>[ 1.882828] can: netlink gateway - max_hops=1 <5>[ 1.887863] Key type dns_resolver registered <6>[ 1.894005] ThumbEE CPU extension supported. <5>[ 1.898546] Registering SWP/SWPB emulation handler <5>[ 1.916526] Loading compiled-in X.509 certificates <3>[ 1.961281] as3722 4-0040: Failed to create device link (0x180) with regulator-5v0sys <3>[ 1.970336] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3sys <3>[ 1.984578] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3run <6>[ 1.993084] reg-fixed-voltage regulator-12v0sata: nonexclusive access to GPIO for (default) <6>[ 1.999755] tegra-dc 54200000.dc: Adding to iommu group 1 <4>[ 2.007453] Failed to attached device 54200000.dc to IOMMU_mapping <6>[ 2.015707] tegra-dc 54240000.dc: Adding to iommu group 1 <4>[ 2.021514] Failed to attached device 54240000.dc to IOMMU_mapping <6>[ 2.026944] Freeing initrd memory: 17108K <6>[ 2.055051] ci_hdrc ci_hdrc.2: EHCI Host Controller <6>[ 2.060268] ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2 <6>[ 2.067785] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 2.099590] ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.10 <6>[ 2.106390] hub 2-0:1.0: USB hub found <6>[ 2.110508] hub 2-0:1.0: 1 port detected <4>[ 2.121437] as3722-regulator as3722-regulator: DMA mask not set <6>[ 2.124598] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.125245] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.125313] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.125352] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.125390] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.125416] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.125638] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.137359] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 2.139550] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 2.142922] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.142987] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.143024] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.143064] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.143089] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.143287] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.162977] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 2.248769] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <4>[ 2.249451] usb2-0: supply vbus not found, using dummy regulator <6>[ 2.257059] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <4>[ 2.261466] usb2-1: supply vbus not found, using dummy regulator <6>[ 2.269445] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 2.276174] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.281483] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <6>[ 2.287582] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.295443] mmc1: new high speed MMC card at address 0001 <3>[ 2.295446] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 2.295969] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 2.302585] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.302619] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.308915] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 2.314175] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.319897] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 2.327332] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.336226] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 2.337035] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 2.338188] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 2.343567] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 2.351535] mmcblk1boot0: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.358823] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 2.363362] mmcblk1boot1: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.403901] mmcblk1rpmb: mmc1:0001 SEM16G 4.00 MiB, chardev (236:0) <6>[ 3.575715] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 3.587013] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 3.593725] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 3.599648] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 3.606870] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 3.613471] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 3.620773] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 3.630090] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 PCIe Root Port <4>[ 3.637751] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 3.647891] pci 0000:00:02.0: PCI bridge to [bus 00] <6>[ 3.653310] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff] <6>[ 3.659898] pci 0000:00:02.0: enabling Extended Tags <6>[ 3.665395] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.689234] PCI: bus0: Fast back to back transfers disabled <6>[ 3.695274] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 3.704350] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint <6>[ 3.712077] pci 0000:01:00.0: BAR 0 [io 0x0000-0x00ff] <6>[ 3.717709] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00000fff 64bit] <6>[ 3.724619] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00003fff 64bit pref] <6>[ 3.732311] pci 0000:01:00.0: supports D1 D2 <6>[ 3.736906] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.769510] PCI: bus1: Fast back to back transfers disabled <6>[ 3.775337] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.782220] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]: assigned <6>[ 3.789985] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref]: assigned <6>[ 3.798681] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]: assigned <6>[ 3.805744] pci 0000:01:00.0: BAR 4 [mem 0x20000000-0x20003fff 64bit pref]: assigned <6>[ 3.813786] pci 0000:01:00.0: BAR 2 [mem 0x13000000-0x13000fff 64bit]: assigned <6>[ 3.821398] pci 0000:01:00.0: BAR 0 [io 0x1000-0x10ff]: assigned <6>[ 3.827757] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 3.832996] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 3.839353] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 3.846412] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <6>[ 3.854439] pci_bus 0000:00: resource 4 [mem 0x01000000-0x01001fff] <6>[ 3.860986] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] <6>[ 3.866819] pci_bus 0000:00: resource 6 [mem 0x13000000-0x1fffffff] <6>[ 3.873358] pci_bus 0000:00: resource 7 [mem 0x20000000-0x3fffffff pref] <6>[ 3.880334] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] <6>[ 3.886166] pci_bus 0000:01: resource 1 [mem 0x13000000-0x130fffff] <6>[ 3.892715] pci_bus 0000:01: resource 2 [mem 0x20000000-0x200fffff 64bit pref] <4>[ 3.900236] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 3.907521] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 3.913978] pcieport 0000:00:02.0: PME: Signaling with IRQ 125 <6>[ 3.920342] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 3.990840] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 127 <6>[ 3.999190] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <4>[ 4.009738] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 4.017629] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 4.025527] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 4.034275] tegra-ahci 70027000.sata: AHCI vers 0001.0301, 32 command slots, 3 Gbps, platform mode <6>[ 4.043499] tegra-ahci 70027000.sata: 1/2 ports implemented (port mask 0x1) <6>[ 4.050736] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 4.061347] scsi host0: tegra-ahci <6>[ 4.065607] scsi host1: tegra-ahci <6>[ 4.069388] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 130 lpm-pol 0 <6>[ 4.078542] ata2: DUMMY <6>[ 4.083034] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.084083] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 4.094662] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 4.108044] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 4.148287] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 4.412277] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 4.422221] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 4.431648] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 4.479736] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC) <6>[ 4.579049] mmc0: new high speed SD card at address 0260 <6>[ 4.586121] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 4.595312] mmcblk0: p1 p2 <6>[ 4.649700] r8169 0000:01:00.0 eth0: Link is Down <6>[ 6.377029] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <5>[ 6.419623] Sending DHCP requests ., OK <6>[ 6.463812] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.214 <6>[ 6.471940] IP-Config: Complete: <6>[ 6.475447] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.214, mask=255.255.255.0, gw=192.168.0.254 <6>[ 6.486129] host=192.168.0.214, domain=shed, nis-domain=(none) <6>[ 6.492736] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 6.492771] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 6.507047] clk: Disabling unused clocks <6>[ 6.511838] PM: genpd: Disabling unused power domains <6>[ 6.519156] Freeing unused kernel image (initmem) memory: 2048K <6>[ 6.525533] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.583098] udevd[147]: starting version 3.2.9 <5>[ 18.029499] random: crng init done <27>[ 18.035828] udevd[147]: specified user 'tss' unknown <27>[ 18.041267] udevd[147]: specified group 'tss' unknown <30>[ 18.047898] udevd[149]: starting eudev-3.2.9 <6>[ 18.165335] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 18.171537] r8169 0000:01:00.0 enp1s0: renamed from eth0 (while UP) <4>[ 18.221802] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 18.231845] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 18.238362] tegra-xusb 70090000.usb: failed to request firmware: -2 <6>[ 18.240446] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 101000 mC <3>[ 18.245002] tegra-xusb 70090000.usb: probe with driver tegra-xusb failed with error -2 <6>[ 18.254621] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 101000 mC <6>[ 18.280714] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 101000 mC <6>[ 18.290462] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 101000 mC <6>[ 18.302312] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC <6>[ 18.313730] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 101000 mC <6>[ 18.352960] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 18.436346] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <6>[ 18.793588] input: NVIDIA Tegra Jetson TK1 Headphones Jack as /devices/soc0/sound/sound/card1/input2 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3895940/environment / # /lava-3895940/bin/lava-test-runner /lava-3895940/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3895940/0/tests/0_dmesg + cat uuid <8>[ 19.466513] + UUID=3895940_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.495831] <8>[ 19.521162] <8>[ 19.545209] + set +x<8>[ 19.554825] / #