- 13:47:02 [INFO] Starting target session
- 13:47:21 [INFO] Connected to beaglebone-black via serial 
- 13:47:21 [INFO] Host: #check prompt
- 13:47:24 [ERROR] On command: #check prompt waiting for #check prompt.+?(?-mix:((?-mix:login:)|[Pp]assword)) >>> error: execution expired
- 13:47:24 [INFO] Target: 
#check prompt
root@am335x-evm:/test# 
- 13:47:24 [INFO] Host: #check prompt
- 13:47:26 [ERROR] On command: #check prompt waiting for #check prompt.+?(?-mix:\/[^\s]* #) >>> error: execution expired
- 13:47:26 [INFO] Target: 
#check prompt
root@am335x-evm:/test# 
- 13:47:26 [INFO] Host: #check prompt
- 13:47:28 [ERROR] On command: #check prompt waiting for #check prompt.+?(?-mix:\/[^\s]* #) >>> error: execution expired
- 13:47:28 [INFO] Target: 
#check prompt
root@am335x-evm:/test# 
- 13:47:28 [INFO] Host: #check prompt
- 13:47:30 [ERROR] On command: #check prompt waiting for #check prompt.+?(?-mix:\/[^\s]* #) >>> error: execution expired
- 13:47:30 [INFO] Target: 
#check prompt
root@am335x-evm:/test# 
- 13:47:30 [INFO] Disconnected serial from beaglebone-black
- 13:47:31 [INFO] Connected to beaglebone-black via serial 
- 13:47:31 [INFO] Host: 
- 13:47:36 [INFO] Target: 

U-Boot SPL 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img


U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)

I2C:   ready
DRAM:  512 MiB
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

Net:   <ethaddr> not set. Validating first E-fuse MAC
Could not get PHY for cpsw: addr 0
cpsw, usb_ether
Hit any key to stop autoboot:  1  0 
U-Boot# 
U-Boot#  
U-Boot#  
U-Boot#  
U-Boot#  
U-Boot#  
U-Boot#  
U-Boot#  
U-Boot#  
U-Boot# 
- 13:47:37 [INFO] Disconnected serial from beaglebone-black
- 13:47:37 [INFO] Connected to beaglebone-black via serial 
- 13:47:37 [INFO] Host: 
- 13:47:37 [INFO] Target: 

U-Boot# 
- 13:47:37 [INFO] Host: version
- 13:47:37 [INFO] Target: 
version

U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
arm-linux-gnueabihf-gcc (crosstool-NG linaro-1.13.1-4.8-2014.03 - Linaro GCC 2014.03) 4.8.3 20140303 (prerelease)
GNU ld (crosstool-NG linaro-1.13.1-4.8-2014.03 - Linaro GCC 2014.03) 2.24.0.20140311 Linaro 2014.03
U-Boot# 
- 13:47:37 [INFO] Host: setenv bootargs 'console=ttyO0,115200n8 earlyprintk=serial,ttyO0,115200n8 rootwait fsck.mode=skip sysrq_always_enabled '
- 13:47:37 [INFO] Target: 
setenv bootargs 'console=ttyO0,115200n8 earlyprintk=serial,ttyO0,115200n8 rootwait fsck.mode=skip sysrq_always_enabled '
U-Boot# 
- 13:47:37 [INFO] Host: setenv bootcmd  ''
- 13:47:38 [INFO] Target: 
setenv bootcmd  ''
U-Boot# 
- 13:47:38 [INFO] Host: setenv autoload 'no'
- 13:47:38 [INFO] Target: 
setenv autoload 'no'
U-Boot# 
- 13:47:38 [INFO] Host: setenv serverip '192.168.0.1'
- 13:47:38 [INFO] Target: 
setenv serverip '192.168.0.1'
U-Boot# 
- 13:47:38 [INFO] Host: setenv _initramfs -
- 13:47:38 [INFO] Target: 
setenv _initramfs -
U-Boot# 
- 13:47:38 [INFO] Host: printenv
- 13:47:39 [INFO] Target: 
printenv
_initramfs=-
arch=arm
autoload=no
baudrate=115200
board=am335x
board_name=A335BNLT
board_rev=00C0
boot_fdt=try
bootargs=console=ttyO0,115200n8 earlyprintk=serial,ttyO0,115200n8 rootwait fsck.mode=skip sysrq_always_enabled 
bootcmd=
bootcount=1
bootdelay=1
bootenv=uEnv.txt
bootfile=zImage
bootpart=0:1
console=ttyO0,115200n8
cpu=armv7
dfu_alt_info_emmc=rawemmc mmc 0 3751936
dfu_alt_info_mmc=boot part 0 1;rootfs part 0 2;MLO fat 0 1;MLO.raw mmc 100 100;u-boot.img.raw mmc 300 400;spl-os-args.raw mmc 80 80;spl-os-image.raw mmc 900 2000;spl-os-args fat 0 1;spl-os-image fat 0 1;u-boot.img fat 0 1;uEnv.txt fat 0 1
dfu_alt_info_nand=SPL part 0 1;SPL.backup1 part 0 2;SPL.backup2 part 0 3;SPL.backup3 part 0 4;u-boot part 0 5;u-boot-spl-os part 0 6;kernel part 0 8;rootfs part 0 9
dfu_alt_info_ram=kernel ram 0x80200000 0xD80000;fdt ram 0x80F80000 0x80000;ramdisk ram 0x81000000 0x4000000
eth1addr=6c:ec:eb:a1:52:c5
ethact=cpsw
ethaddr=6c:ec:eb:a1:52:c3
fdt_high=0xffffffff
fdtaddr=0x88000000
fdtdir=/dtbs
fdtfile=undefined
findfdt=if test $board_name = A335BONE; then setenv fdtfile am335x-bone.dtb; setenv fdtbase am335x-bone; fi; if test $board_name = A335BNLT; then setenv fdtfile am335x-boneblack.dtb; setenv fdtbase am335x-boneblack; fi; if test $board_name = A33515BB; then setenv fdtfile am335x-evm.dtb; fi; if test $board_name = A335X_SK; then setenv fdtfile am335x-evmsk.dtb; fi; if test $fdtfile = undefined; then echo WARNING: Could not determine device tree to use; fi; 
importbootenv=echo Importing environment from mmc ...; env import -t $loadaddr $filesize
loadaddr=0x82000000
loadbootenv=load mmc ${bootpart} ${loadaddr} ${bootenv}
loadfdt=load mmc ${bootpart} ${fdtaddr} ${fdtdir}/${fdtfile}
loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}
loadramdisk=load mmc ${mmcdev} ${rdaddr} ramdisk.gz
mmcargs=setenv bootargs console=${console} ${optargs} root=${mmcroot} rootfstype=${mmcrootfstype}
mmcboot=mmc dev ${mmcdev}; if mmc rescan; then gpio set 54;echo SD/MMC found on device ${mmcdev};if run loadbootenv; then gpio set 55;echo Loaded environment from ${bootenv};run importbootenv;fi;if test -n $cape; then if test -e mmc ${bootpart} ${fdtdir}/$fdtbase-$cape.dtb; then setenv fdtfile $fdtbase-$cape.dtb; fi; echo using: $fdtfile...; fi; echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then gpio set 56; echo Running uenvcmd ...;run uenvcmd;fi;echo; echo uenvcmd was not defined in uEnv.txt ...;fi;
mmcdev=0
mmcloados=run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdtaddr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;
mmcpart=1
mmcroot=/dev/mmcblk0p2 ro fixrtc
mmcrootfstype=ext4 rootwait
mtdids=nand0=omap2-nand.0
mtdparts=mtdparts=omap2-nand.0:128k(SPL),128k(SPL.backup1),128k(SPL.backup2),128k(SPL.backup3),1792k(u-boot),128k(u-boot-spl-os),128k(u-boot-env),5m(kernel),-(rootfs)
nandargs=setenv bootargs console=${console} ${optargs} root=${nandroot} rootfstype=${nandrootfstype}
nandboot=echo Booting from nand ...; run nandargs; nand read ${fdtaddr} u-boot-spl-os; nand read ${loadaddr} kernel; bootz ${loadaddr} - ${fdtaddr}
nandroot=ubi0:rootfs rw ubi.mtd=7,2048
nandrootfstype=ubifs rootwait=1
netargs=setenv bootargs console=${console} ${optargs} root=/dev/nfs nfsroot=${serverip}:${rootpath},${nfsopts} rw ip=dhcp
netboot=echo Booting from network ...; setenv autoload no; dhcp; tftp ${loadaddr} ${bootfile}; tftp ${fdtaddr} ${fdtfile}; run netargs; bootz ${loadaddr} - ${fdtaddr}
nfsopts=nolock
partitions=uuid_disk=${uuid_gpt_disk};name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}
ramargs=setenv bootargs console=${console} ${optargs} root=${ramroot} rootfstype=${ramrootfstype}
ramboot=echo Booting from ramdisk ...; run ramargs; bootz ${loadaddr} ${rdaddr} ${fdtaddr}
ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=${rdaddr},64M
ramrootfstype=ext2
rdaddr=0x88080000
rootpath=/export/rootfs
serverip=192.168.0.1
soc=am33xx
spiargs=setenv bootargs console=${console} ${optargs} root=${spiroot} rootfstype=${spirootfstype}
spiboot=echo Booting from spi ...; run spiargs; sf probe ${spibusno}:0; sf read ${loadaddr} ${spisrcaddr} ${spiimgsize}; bootz ${loadaddr}
spibusno=0
spiimgsize=0x362000
spiroot=/dev/mtdblock4 rw
spirootfstype=jffs2
spisrcaddr=0xe0000
static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off
stderr=serial
stdin=serial
stdout=serial
usbnet_devaddr=6c:ec:eb:a1:52:c5
vendor=ti
ver=U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)

Environment size: 4710/131068 bytes
U-Boot# 
- 13:47:39 [INFO] Host: printenv bootargs
- 13:47:39 [INFO] Target: 
printenv bootargs
bootargs=console=ttyO0,115200n8 earlyprintk=serial,ttyO0,115200n8 rootwait fsck.mode=skip sysrq_always_enabled 
U-Boot# 
- 13:47:39 [INFO] Host: setenv bootargs ''${bootargs}' ip=:::::eth0:dhcp '
- 13:47:39 [INFO] Target: 
setenv bootargs ''${bootargs}' ip=:::::eth0:dhcp '
U-Boot# 
- 13:47:39 [INFO] Host: setenv serverip '192.168.0.1'
- 13:47:39 [INFO] Target: 
setenv serverip '192.168.0.1'
U-Boot# 
- 13:47:39 [INFO] Host: setenv autoload 'no'
- 13:47:40 [INFO] Target: 
setenv autoload 'no'
U-Boot# 
- 13:47:40 [INFO] Host: dhcp
- 13:48:20 [ERROR] On command: dhcp waiting for dhcp.+?(?mi-x:DHCP client bound to address.*(?-mix:(?-mix:U-Boot#)|=>)) >>> error: execution expired
- 13:48:20 [INFO] Target: 
dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10

Retry count exceeded; starting again
using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC 6c:ec:eb:a1:52:c5
HOST MAC de:ad:be:af:00:00
RNDIS ready
ERROR: The remote end did not respond in time.
at drivers/usb/gadget/ether.c:2388/usb_eth_init()

- 13:48:30 [INFO] 
Abort
U-Boot# 
U-Boot# 
- 13:48:30 [INFO] Host: dhcp
- 13:49:10 [ERROR] On command: dhcp waiting for dhcp.+?(?mi-x:DHCP client bound to address.*(?-mix:(?-mix:U-Boot#)|=>)) >>> error: execution expired
- 13:49:10 [INFO] Target: 
dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10

Retry count exceeded; starting again
using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC 6c:ec:eb:a1:52:c5
HOST MAC de:ad:be:af:00:00
RNDIS ready
ERROR: The remote end did not respond in time.
at drivers/usb/gadget/ether.c:2388/usb_eth_init()

- 13:49:20 [INFO] 
Abort
U-Boot# 
U-Boot# 
- 13:49:20 [INFO] Host: dhcp
- 13:50:00 [ERROR] On command: dhcp waiting for dhcp.+?(?mi-x:DHCP client bound to address.*(?-mix:(?-mix:U-Boot#)|=>)) >>> error: execution expired
- 13:50:00 [INFO] Target: 
dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10

Retry count exceeded; starting again
using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC 6c:ec:eb:a1:52:c5
HOST MAC de:ad:be:af:00:00
RNDIS ready
ERROR: The remote end did not respond in time.
at drivers/usb/gadget/ether.c:2388/usb_eth_init()

- 13:50:10 [INFO] 
Abort
U-Boot# 
U-Boot# 
- 13:50:10 [INFO] Boot attempt 1/1 failed
- 13:50:10 [INFO] Collecting kernel traces via sysrq...
- 13:50:20 [INFO] t
U-Boot# 
- 13:50:30 [INFO] l
U-Boot# 
- 13:50:41 [INFO] w
U-Boot# 
- 13:50:41 [INFO] Disconnected serial from beaglebone-black
- 13:50:41 [INFO] Host: cd /test