connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='default', state=, avail=True, host='nuc-1', port=39083, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:39083 connected to 192.168.0.1 (port 39083) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 DHCP client bound to address 192.168.0.212 (3333 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3906451/tftp-deploy-4rursqtx/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906451/tftp-deploy-4rursqtx/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################### 1.9 MiB/s done Bytes transferred = 10998272 (a7d200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3906451/tftp-deploy-4rursqtx/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906451/tftp-deploy-4rursqtx/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 2.7 MiB/s done Bytes transferred = 17857971 (1107db3 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3906451/tftp-deploy-4rursqtx/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906451/tftp-deploy-4rursqtx/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *###### 1.9 MiB/s done Bytes transferred = 73434 (11eda hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0xa7d200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17857907 Bytes = 17 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f94ed9 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc5 (KernelCI@build-j360689-arm-gcc-12-multi-v7-defconfig-config-smp-n-grjpw) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 Sun Nov 3 19:52:38 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: legacy bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm/kernel/devtree.c:129 arm_dt_init_cpu_maps+0xbc/0x120 [ 0.000000] DT /cpu 2 nodes greater than max cores 1, capping them [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 UID: 0 PID: 0 Comm: swapper Not tainted 6.12.0-rc5 #1 [ 0.000000] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [ 0.000000] Call trace: [ 0.000000] unwind_backtrace from show_stack+0x10/0x14 [ 0.000000] show_stack from dump_stack_lvl+0x50/0x58 [ 0.000000] dump_stack_lvl from __warn+0x7c/0x104 [ 0.000000] __warn from warn_slowpath_fmt+0x98/0xc8 [ 0.000000] warn_slowpath_fmt from arm_dt_init_cpu_maps+0xbc/0x120 [ 0.000000] arm_dt_init_cpu_maps from setup_arch+0x44c/0x680 [ 0.000000] setup_arch from start_kernel+0x68/0x6a4 [ 0.000000] start_kernel from 0x0 [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524032 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000000] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.000000] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.008577] Switching to timer-based delay loop, resolution 83ns <6>[ 0.015651] Console: colour dummy device 80x30 <6>[ 0.020569] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.031597] CPU: Testing write buffer coherency: ok <6>[ 0.036958] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.042561] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.049419] pid_max: default: 32768 minimum: 301 <6>[ 0.054591] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.062448] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.100836] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.111679] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.120805] EFI services will not be available. <6>[ 0.125809] Memory: 1965868K/2096128K available (15360K kernel code, 2542K rwdata, 6716K rodata, 2048K init, 413K bss, 62512K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.142543] devtmpfs: initialized <6>[ 0.159340] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.167737] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.178222] futex hash table entries: 256 (order: -1, 3072 bytes, linear) <6>[ 0.186743] pinctrl core: initialized pinctrl subsystem <6>[ 0.196252] DMI not present or invalid. <6>[ 0.201199] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.209312] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.219654] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.219679] cpuidle: using governor menu <6>[ 0.243310] platform 70000868.pinmux: Fixed dependency cycle(s) with /pinmux@70000868/pinmux <6>[ 0.274914] No ATAGs? <6>[ 0.277548] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.286135] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.305622] Serial: AMBA PL011 UART driver <3>[ 0.311256] tegra-mc 70019000.memory-controller: ppcsahbslvr: secure read @0x7fd41100: EMEM address decode error (EMEM decode error) <6>[ 0.350802] iommu: Default domain type: Translated <6>[ 0.356072] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.363881] SCSI subsystem initialized <6>[ 0.398429] usbcore: registered new interface driver usbfs <6>[ 0.404437] usbcore: registered new interface driver hub <6>[ 0.410276] usbcore: registered new device driver usb <6>[ 0.417289] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.422734] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.432520] PTP clock support registered <6>[ 0.437019] EDAC MC: Ver: 3.0.0 <6>[ 0.484946] scmi_core: SCMI protocol bus registered <6>[ 0.492372] vgaarb: loaded <6>[ 0.505373] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.540362] NET: Registered PF_INET protocol family <6>[ 0.545908] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.555299] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.564386] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.572732] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.581143] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.588984] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.595925] UDP hash table entries: 512 (order: 1, 8192 bytes, linear) <6>[ 0.603014] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear) <6>[ 0.610653] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.685043] RPC: Registered named UNIX socket transport module. <6>[ 0.691490] RPC: Registered udp transport module. <6>[ 0.696661] RPC: Registered tcp transport module. <6>[ 0.701822] RPC: Registered tcp-with-tls transport module. <6>[ 0.707804] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.714777] PCI: CLS 0 bytes, default 64 <5>[ 0.720011] Initialise system trusted keyrings <6>[ 0.738929] Trying to unpack rootfs image as initramfs... <6>[ 0.819337] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.826649] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.860572] NFS: Registering the id_resolver key type <5>[ 0.866143] Key type id_resolver registered <5>[ 0.870765] Key type id_legacy registered <6>[ 0.875232] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.882499] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.936037] Key type asymmetric registered <5>[ 0.940576] Asymmetric key parser 'x509' registered <6>[ 0.946007] bounce: pool size: 64 pages <6>[ 0.950306] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.958284] io scheduler mq-deadline registered <6>[ 0.963268] io scheduler kyber registered <6>[ 0.967736] io scheduler bfq registered <4>[ 0.988496] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 1.144705] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.168847] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 1.181253] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 1.419487] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.469027] printk: legacy console [ttyS0] disabled <6>[ 1.474714] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 62, base_baud = 25500000) is a Tegra <6>[ 1.484263] printk: legacy console [ttyS0] enabled <6>[ 1.484263] printk: legacy console [ttyS0] enabled <6>[ 1.494530] printk: legacy bootconsole [uart0] disabled <6>[ 1.494530] printk: legacy bootconsole [uart0] disabled <6>[ 1.597127] msm_serial: driver initialized <6>[ 1.601883] SuperH (H)SCI(F) driver initialized <6>[ 1.607027] STMicroelectronics ASC driver initialized <6>[ 1.612454] STM32 USART driver initialized <6>[ 1.617832] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 63, base_baud = 0) is a TEGRA_UART <6>[ 1.686149] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART <6>[ 1.718750] tegra-host1x 50000000.host1x: Adding to iommu group 0 <6>[ 1.733262] tegra-vic 54340000.vic: Adding to iommu group 1 <6>[ 1.816677] brd: module loaded <6>[ 1.839905] loop: module loaded <3>[ 1.880227] spi spi1.0: Invalid delay unit 2, should be SPI_DELAY_UNIT_SCK <3>[ 1.887384] spi-tegra114 7000da00.spi: can't setup spi1.0, status -22 <3>[ 1.894082] spi_master spi1: spi_device register error /spi@7000da00/flash@0 <4>[ 1.901412] spi_master spi1: Failed to create SPI device for /spi@7000da00/flash@0 <6>[ 1.914099] CAN device driver interface <6>[ 1.919399] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.926563] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.931783] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.937995] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.943648] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.954358] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.960232] usbcore: registered new interface driver pegasus <6>[ 1.966185] usbcore: registered new interface driver asix <6>[ 1.971870] usbcore: registered new interface driver ax88179_178a <6>[ 1.978267] usbcore: registered new interface driver cdc_ether <6>[ 1.984381] usbcore: registered new interface driver smsc75xx <6>[ 1.990420] usbcore: registered new interface driver smsc95xx <6>[ 1.996458] usbcore: registered new interface driver net1080 <6>[ 2.002397] usbcore: registered new interface driver cdc_subset <6>[ 2.008613] usbcore: registered new interface driver zaurus <6>[ 2.014468] usbcore: registered new interface driver cdc_ncm <4>[ 2.020778] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 2.029139] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 2.041540] usbcore: registered new interface driver usb-storage <6>[ 2.502352] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.507532] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.565483] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.10 <6>[ 2.576687] hub 1-0:1.0: USB hub found <6>[ 2.595410] hub 1-0:1.0: 1 port detected <6>[ 2.636306] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 2.641711] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 2.648730] i2c_dev: i2c /dev entries driver <4>[ 2.687621] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 2.726327] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 2.758359] i2c 4-0040: Fixed dependency cycle(s) with /i2c@7000d000/pmic@40/pinmux <6>[ 2.797162] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 2.898263] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 2.915563] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:23 UTC (946684823) <6>[ 2.924443] as3722-rtc as3722-rtc: RTC interrupt 93 <6>[ 2.952240] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 2.964140] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 2.993784] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <4>[ 3.025392] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 3.033413] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 3.046178] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <3>[ 3.078111] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 3.084054] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 3.092946] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 3.099927] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 3.145840] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.152280] sdhci: Copyright(c) Pierre Ossman <6>[ 3.158950] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.166988] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.177516] usbcore: registered new interface driver usbhid <6>[ 3.183346] usbhid: USB HID core driver <6>[ 3.191665] tegra-emc 7001b000.external-memory-controller: 64bit DRAM bus <6>[ 3.199986] tegra-emc 7001b000.external-memory-controller: OPP HW ver. 0x2, current clock rate 924 MHz <4>[ 3.210928] armv7-pmu pmu: hw perfevents: failed to find logical CPU for cpu <4>[ 3.218271] armv7-pmu pmu: hw perfevents: failed to find logical CPU for cpu <4>[ 3.225606] armv7-pmu pmu: hw perfevents: failed to find logical CPU for cpu <6>[ 3.233087] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 (8000003f) counters available <6>[ 3.245102] NET: Registered PF_INET6 protocol family <6>[ 3.253298] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 3.258324] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 3.386174] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 3.506644] Segment Routing with IPv6 <6>[ 3.510630] In-situ OAM (IOAM) with IPv6 <6>[ 3.514882] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.521635] NET: Registered PF_PACKET protocol family <6>[ 3.526963] can: controller area network core <6>[ 3.531608] NET: Registered PF_CAN protocol family <6>[ 3.536667] can: raw protocol <6>[ 3.539896] can: broadcast manager protocol <6>[ 3.544341] can: netlink gateway - max_hops=1 <5>[ 3.549303] Key type dns_resolver registered <6>[ 3.554634] ThumbEE CPU extension supported. <5>[ 3.559187] Registering SWP/SWPB emulation handler <5>[ 3.716395] Loading compiled-in X.509 certificates <6>[ 3.782164] tegra-dc 54200000.dc: Adding to iommu group 1 <4>[ 3.787883] Failed to attached device 54200000.dc to IOMMU_mapping <6>[ 3.795238] tegra-dc 54240000.dc: Adding to iommu group 1 <4>[ 3.800934] Failed to attached device 54240000.dc to IOMMU_mapping <3>[ 3.837149] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3run <6>[ 3.869831] reg-fixed-voltage regulator-12v0sata: nonexclusive access to GPIO for (default) <4>[ 3.879477] as3722-regulator as3722-regulator: DMA mask not set <6>[ 3.888347] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 3.893353] sdhci-tegra 700b0400.mmc: Got WP GPIO <3>[ 3.941035] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 3.965979] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <4>[ 3.986735] usb2-0: supply vbus not found, using dummy regulator <4>[ 3.993237] usb2-1: supply vbus not found, using dummy regulator <6>[ 4.002063] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 4.017699] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.024518] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.032896] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.041270] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.049635] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.058128] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 4.085588] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 4.106434] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 4.137846] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 4.146165] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 4.367877] Freeing initrd memory: 17440K <6>[ 4.411144] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 4.471820] mmc1: new high speed MMC card at address 0001 <6>[ 4.477995] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 4.485694] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 4.491698] mmcblk1boot0: mmc1:0001 SEM16G 4.00 MiB <6>[ 4.497820] mmcblk1boot1: mmc1:0001 SEM16G 4.00 MiB <6>[ 4.503871] mmcblk1rpmb: mmc1:0001 SEM16G 4.00 MiB, chardev (236:0) <6>[ 5.447404] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 5.459570] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 5.466118] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 5.471864] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 5.479007] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 5.485453] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 5.492582] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 5.500561] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 PCIe Root Port <4>[ 5.508149] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 5.518085] pci 0000:00:02.0: PCI bridge to [bus 00] <6>[ 5.523314] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff] <6>[ 5.529692] pci 0000:00:02.0: enabling Extended Tags <6>[ 5.534973] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.546424] PCI: bus0: Fast back to back transfers disabled <6>[ 5.552259] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 5.560692] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint <6>[ 5.568210] pci 0000:01:00.0: BAR 0 [io 0x0000-0x00ff] <6>[ 5.573723] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00000fff 64bit] <6>[ 5.580447] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00003fff 64bit pref] <6>[ 5.587758] pci 0000:01:00.0: supports D1 D2 <6>[ 5.592286] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.615439] PCI: bus1: Fast back to back transfers disabled <6>[ 5.621273] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 5.628180] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]: assigned <6>[ 5.635934] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref]: assigned <6>[ 5.644626] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]: assigned <6>[ 5.651684] pci 0000:01:00.0: BAR 4 [mem 0x20000000-0x20003fff 64bit pref]: assigned <6>[ 5.659715] pci 0000:01:00.0: BAR 2 [mem 0x13000000-0x13000fff 64bit]: assigned <6>[ 5.667305] pci 0000:01:00.0: BAR 0 [io 0x1000-0x10ff]: assigned <6>[ 5.673662] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 5.678897] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 5.685250] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 5.692311] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <6>[ 5.700322] pci_bus 0000:00: resource 4 [mem 0x01000000-0x01001fff] <6>[ 5.706856] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] <6>[ 5.712686] pci_bus 0000:00: resource 6 [mem 0x13000000-0x1fffffff] <6>[ 5.719215] pci_bus 0000:00: resource 7 [mem 0x20000000-0x3fffffff pref] <6>[ 5.726184] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] <6>[ 5.732013] pci_bus 0000:01: resource 1 [mem 0x13000000-0x130fffff] <6>[ 5.738546] pci_bus 0000:01: resource 2 [mem 0x20000000-0x200fffff 64bit pref] <4>[ 5.746056] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 5.753365] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 5.759849] pcieport 0000:00:02.0: PME: Signaling with IRQ 116 <6>[ 5.766281] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 5.828016] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 118 <6>[ 5.836401] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <4>[ 5.852948] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 5.860920] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 5.868796] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 5.877837] tegra-ahci 70027000.sata: AHCI vers 0001.0301, 32 command slots, 3 Gbps, platform mode <6>[ 5.887073] tegra-ahci 70027000.sata: 1/2 ports implemented (port mask 0x1) <6>[ 5.894290] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 5.904683] scsi host0: tegra-ahci <6>[ 5.908839] scsi host1: tegra-ahci <6>[ 5.912700] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 121 lpm-pol 0 <6>[ 5.921840] ata2: DUMMY <6>[ 5.950429] ci_hdrc ci_hdrc.2: EHCI Host Controller <6>[ 5.955608] ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2 <6>[ 5.975404] ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.10 <6>[ 5.981727] hub 2-0:1.0: USB hub found <6>[ 5.985785] hub 2-0:1.0: 1 port detected <6>[ 5.991295] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 6.005456] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 6.010454] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 6.015843] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <4>[ 6.025504] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 6.073654] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 6.247530] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 6.255719] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 6.265062] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 6.295379] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC) <6>[ 6.436063] r8169 0000:01:00.0 eth0: Link is Down <6>[ 6.531103] mmc0: new high speed SD card at address 0260 <6>[ 6.537501] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 6.544900] mmcblk0: p1 p2 <6>[ 8.025066] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <5>[ 8.055396] Sending DHCP requests ., OK <6>[ 8.099578] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.212 <6>[ 8.107673] IP-Config: Complete: <6>[ 8.111186] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.212, mask=255.255.255.0, gw=192.168.0.254 <6>[ 8.121896] host=192.168.0.212, domain=shed, nis-domain=(none) <6>[ 8.128487] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 8.128524] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 8.142787] clk: Disabling unused clocks <6>[ 8.147623] PM: genpd: Disabling unused power domains <6>[ 8.154669] Freeing unused kernel image (initmem) memory: 2048K <6>[ 8.160944] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.210610] udevd[100]: starting version 3.2.9 <5>[ 15.895379] random: crng init done <27>[ 15.901534] udevd[100]: specified user 'tss' unknown <27>[ 15.906972] udevd[100]: specified group 'tss' unknown <30>[ 15.913287] udevd[101]: starting eudev-3.2.9 <6>[ 16.805853] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 16.846346] r8169 0000:01:00.0 enp1s0: renamed from eth0 (while UP) <4>[ 16.991192] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 17.001186] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 17.007707] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 17.014239] tegra-xusb 70090000.usb: probe with driver tegra-xusb failed with error -2 <6>[ 17.058462] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 101000 mC <6>[ 17.068199] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 101000 mC <6>[ 17.078144] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 101000 mC <6>[ 17.087868] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 101000 mC <6>[ 17.097787] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC <6>[ 17.107788] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 101000 mC <6>[ 17.193546] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 17.745482] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub done Saving random seed: OK <6>[ 17.771341] input: NVIDIA Tegra Jetson TK1 Headphones Jack as /devices/soc0/sound/sound/card1/input2 Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3906451/environment / # /lava-3906451/bin/lava-test-runner /lava-3906451/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3906451/0/tests/0<8>[ 18.408900] _dmesg + cat uuid + UUID=3906451_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.430938] <8>[ 18.450487] <8>[ 18.470131] + set +x <8>[ 18.479126] / #