connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='default', state=, avail=True, host='nuc-1', port=39083, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:39083 connected to 192.168.0.1 (port 39083) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 DHCP client bound to address 192.168.0.212 (5217 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3906453/tftp-deploy-l4b_ya5g/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906453/tftp-deploy-l4b_ya5g/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################### 2.7 MiB/s done Bytes transferred = 10998272 (a7d200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3906453/tftp-deploy-l4b_ya5g/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906453/tftp-deploy-l4b_ya5g/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 2.6 MiB/s done Bytes transferred = 14679029 (dffbf5 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3906453/tftp-deploy-l4b_ya5g/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906453/tftp-deploy-l4b_ya5g/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *###### 2.1 MiB/s done Bytes transferred = 73434 (11eda hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=192.168.0.2:/var/lib/lava/dispatcher/tmp/3906453/extract-nfsrootfs-ut982tee,tcp,hard,vers=3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0xa7d200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14678965 Bytes = 14 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f94ed9 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc5 (KernelCI@build-j360689-arm-gcc-12-multi-v7-defconfig-config-smp-n-grjpw) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 Sun Nov 3 19:52:38 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: legacy bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm/kernel/devtree.c:129 arm_dt_init_cpu_maps+0xbc/0x120 [ 0.000000] DT /cpu 2 nodes greater than max cores 1, capping them [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 UID: 0 PID: 0 Comm: swapper Not tainted 6.12.0-rc5 #1 [ 0.000000] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [ 0.000000] Call trace: [ 0.000000] unwind_backtrace from show_stack+0x10/0x14 [ 0.000000] show_stack from dump_stack_lvl+0x50/0x58 [ 0.000000] dump_stack_lvl from __warn+0x7c/0x104 [ 0.000000] __warn from warn_slowpath_fmt+0x98/0xc8 [ 0.000000] warn_slowpath_fmt from arm_dt_init_cpu_maps+0xbc/0x120 [ 0.000000] arm_dt_init_cpu_maps from setup_arch+0x44c/0x680 [ 0.000000] setup_arch from start_kernel+0x68/0x6a4 [ 0.000000] start_kernel from 0x0 [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=192.168.0.2:/var/lib/lava/dispatcher/tmp/3906453/extract-nfsrootfs-ut982tee,tcp,hard,vers=3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524032 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000000] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.000001] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.008577] Switching to timer-based delay loop, resolution 83ns <6>[ 0.015646] Console: colour dummy device 80x30 <6>[ 0.020567] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.031594] CPU: Testing write buffer coherency: ok <6>[ 0.036954] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.042558] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.049417] pid_max: default: 32768 minimum: 301 <6>[ 0.054589] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.062448] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.100835] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.111685] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.120809] EFI services will not be available. <6>[ 0.125813] Memory: 1968968K/2096128K available (15360K kernel code, 2542K rwdata, 6716K rodata, 2048K init, 413K bss, 59412K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.142548] devtmpfs: initialized <6>[ 0.159357] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.167754] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.178240] futex hash table entries: 256 (order: -1, 3072 bytes, linear) <6>[ 0.186735] pinctrl core: initialized pinctrl subsystem <6>[ 0.196213] DMI not present or invalid. <6>[ 0.201160] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.209279] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.219631] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.219655] cpuidle: using governor menu <6>[ 0.243092] platform 70000868.pinmux: Fixed dependency cycle(s) with /pinmux@70000868/pinmux <6>[ 0.274661] No ATAGs? <6>[ 0.277295] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.285880] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.305360] Serial: AMBA PL011 UART driver <3>[ 0.311000] tegra-mc 70019000.memory-controller: ppcsahbslvr: secure read @0x7fd41100: EMEM address decode error (EMEM decode error) <6>[ 0.350576] iommu: Default domain type: Translated <6>[ 0.355846] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.363656] SCSI subsystem initialized <6>[ 0.398874] usbcore: registered new interface driver usbfs <6>[ 0.404882] usbcore: registered new interface driver hub <6>[ 0.410721] usbcore: registered new device driver usb <6>[ 0.417730] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.423175] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.432961] PTP clock support registered <6>[ 0.437462] EDAC MC: Ver: 3.0.0 <6>[ 0.484210] scmi_core: SCMI protocol bus registered <6>[ 0.491635] vgaarb: loaded <6>[ 0.504662] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.529972] NET: Registered PF_INET protocol family <6>[ 0.535519] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.544926] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.553994] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.562344] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.570755] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.578595] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.585538] UDP hash table entries: 512 (order: 1, 8192 bytes, linear) <6>[ 0.592628] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear) <6>[ 0.600266] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.684329] RPC: Registered named UNIX socket transport module. <6>[ 0.690775] RPC: Registered udp transport module. <6>[ 0.695945] RPC: Registered tcp transport module. <6>[ 0.701106] RPC: Registered tcp-with-tls transport module. <6>[ 0.707090] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.714064] PCI: CLS 0 bytes, default 64 <5>[ 0.719314] Initialise system trusted keyrings <6>[ 0.738188] Trying to unpack rootfs image as initramfs... <6>[ 0.815651] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.822938] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.876234] NFS: Registering the id_resolver key type <5>[ 0.881806] Key type id_resolver registered <5>[ 0.886444] Key type id_legacy registered <6>[ 0.890907] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.898163] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.954981] Key type asymmetric registered <5>[ 0.959519] Asymmetric key parser 'x509' registered <6>[ 0.964966] bounce: pool size: 64 pages <6>[ 0.969265] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.977244] io scheduler mq-deadline registered <6>[ 0.982227] io scheduler kyber registered <6>[ 0.986701] io scheduler bfq registered <4>[ 1.007384] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 1.167333] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.191493] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 1.203895] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 1.468766] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.515446] printk: legacy console [ttyS0] disabled <6>[ 1.521143] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 62, base_baud = 25500000) is a Tegra <6>[ 1.530693] printk: legacy console [ttyS0] enabled <6>[ 1.530693] printk: legacy console [ttyS0] enabled <6>[ 1.540965] printk: legacy bootconsole [uart0] disabled <6>[ 1.540965] printk: legacy bootconsole [uart0] disabled <6>[ 1.636171] msm_serial: driver initialized <6>[ 1.640925] SuperH (H)SCI(F) driver initialized <6>[ 1.646075] STMicroelectronics ASC driver initialized <6>[ 1.651508] STM32 USART driver initialized <6>[ 1.656899] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 63, base_baud = 0) is a TEGRA_UART <6>[ 1.735743] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART <6>[ 1.767830] tegra-host1x 50000000.host1x: Adding to iommu group 0 <6>[ 1.782361] tegra-vic 54340000.vic: Adding to iommu group 1 <6>[ 1.896886] brd: module loaded <6>[ 1.904448] loop: module loaded <3>[ 1.955914] spi spi1.0: Invalid delay unit 2, should be SPI_DELAY_UNIT_SCK <3>[ 1.963053] spi-tegra114 7000da00.spi: can't setup spi1.0, status -22 <3>[ 1.969772] spi_master spi1: spi_device register error /spi@7000da00/flash@0 <4>[ 1.977104] spi_master spi1: Failed to create SPI device for /spi@7000da00/flash@0 <6>[ 1.989796] CAN device driver interface <6>[ 1.995089] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.002234] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.007467] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.013670] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.019334] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.030031] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.035902] usbcore: registered new interface driver pegasus <6>[ 2.041842] usbcore: registered new interface driver asix <6>[ 2.047535] usbcore: registered new interface driver ax88179_178a <6>[ 2.053914] usbcore: registered new interface driver cdc_ether <6>[ 2.060042] usbcore: registered new interface driver smsc75xx <6>[ 2.066080] usbcore: registered new interface driver smsc95xx <6>[ 2.072106] usbcore: registered new interface driver net1080 <6>[ 2.078056] usbcore: registered new interface driver cdc_subset <6>[ 2.084261] usbcore: registered new interface driver zaurus <6>[ 2.090131] usbcore: registered new interface driver cdc_ncm <4>[ 2.096440] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 2.104798] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 2.117209] usbcore: registered new interface driver usb-storage <6>[ 2.558211] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.563374] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.615319] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.10 <6>[ 2.621732] hub 1-0:1.0: USB hub found <6>[ 2.645771] hub 1-0:1.0: 1 port detected <6>[ 2.665419] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 2.670824] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 2.677850] i2c_dev: i2c /dev entries driver <4>[ 2.726886] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 2.746410] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 2.799393] i2c 4-0040: Fixed dependency cycle(s) with /i2c@7000d000/pmic@40/pinmux <6>[ 2.846212] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 2.931580] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 2.939312] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:23 UTC (946684823) <6>[ 2.948216] as3722-rtc as3722-rtc: RTC interrupt 93 <6>[ 2.985752] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <4>[ 3.003644] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 3.038449] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 3.045443] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 3.055474] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 3.095008] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.101446] sdhci: Copyright(c) Pierre Ossman <6>[ 3.108112] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.116157] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.126660] usbcore: registered new interface driver usbhid <6>[ 3.132490] usbhid: USB HID core driver <6>[ 3.140854] tegra-emc 7001b000.external-memory-controller: 64bit DRAM bus <6>[ 3.149169] tegra-emc 7001b000.external-memory-controller: OPP HW ver. 0x2, current clock rate 924 MHz <4>[ 3.160113] armv7-pmu pmu: hw perfevents: failed to find logical CPU for cpu <4>[ 3.167456] armv7-pmu pmu: hw perfevents: failed to find logical CPU for cpu <4>[ 3.174790] armv7-pmu pmu: hw perfevents: failed to find logical CPU for cpu <6>[ 3.182272] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 (8000003f) counters available <6>[ 3.194298] NET: Registered PF_INET6 protocol family <6>[ 3.276029] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 3.281037] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 3.315302] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <4>[ 3.364915] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 3.394917] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 3.428235] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <3>[ 3.465389] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 3.471332] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 3.516437] Segment Routing with IPv6 <6>[ 3.520422] In-situ OAM (IOAM) with IPv6 <6>[ 3.524692] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.531398] NET: Registered PF_PACKET protocol family <6>[ 3.536728] can: controller area network core <6>[ 3.541378] NET: Registered PF_CAN protocol family <6>[ 3.546438] can: raw protocol <6>[ 3.549666] can: broadcast manager protocol <6>[ 3.554109] can: netlink gateway - max_hops=1 <5>[ 3.559056] Key type dns_resolver registered <6>[ 3.564381] ThumbEE CPU extension supported. <5>[ 3.568936] Registering SWP/SWPB emulation handler <5>[ 3.705313] Loading compiled-in X.509 certificates <6>[ 3.781339] tegra-dc 54200000.dc: Adding to iommu group 1 <4>[ 3.787054] Failed to attached device 54200000.dc to IOMMU_mapping <6>[ 3.794408] tegra-dc 54240000.dc: Adding to iommu group 1 <4>[ 3.800106] Failed to attached device 54240000.dc to IOMMU_mapping <3>[ 3.816907] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3run <6>[ 3.849337] reg-fixed-voltage regulator-12v0sata: nonexclusive access to GPIO for (default) <6>[ 3.859944] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 3.864962] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 3.870785] as3722-regulator as3722-regulator: DMA mask not set <6>[ 3.951103] Freeing initrd memory: 14336K <6>[ 3.967706] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 3.974546] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 3.982936] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 3.991311] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 3.999676] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.008170] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <3>[ 4.014384] tegra-pcie 1003000.pcie: failed to get PHY#0: -517 <3>[ 4.020496] tegra-pcie 1003000.pcie: failed to get PHYs: -517 <3>[ 4.026506] tegra-pcie 1003000.pcie: failed to request resources: -517 <6>[ 4.060580] mmc0: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <3>[ 4.071329] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 4.077678] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 4.084819] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 4.091815] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 4.098774] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 4.108397] ci_hdrc ci_hdrc.2: EHCI Host Controller <6>[ 4.113553] ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2 <6>[ 4.134687] ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.10 <6>[ 4.141024] hub 2-0:1.0: USB hub found <6>[ 4.145108] hub 2-0:1.0: 1 port detected <6>[ 4.150867] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 4.165948] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 4.170947] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 4.176445] usb2-0: supply vbus not found, using dummy regulator <4>[ 4.182836] usb2-1: supply vbus not found, using dummy regulator <6>[ 4.190003] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.196797] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.205138] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.213474] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.221812] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.230199] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 4.236278] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 4.247473] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 4.255189] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <3>[ 4.263631] tegra-pcie 1003000.pcie: Unknown, signature: 00000008 <6>[ 4.279413] mmc0: new high speed MMC card at address 0001 <6>[ 4.285301] mmc1: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 4.293413] mmcblk0: mmc0:0001 SEM16G 14.7 GiB <6>[ 4.300821] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 4.306002] mmcblk0boot0: mmc0:0001 SEM16G 4.00 MiB <6>[ 4.311574] mmcblk0boot1: mmc0:0001 SEM16G 4.00 MiB <6>[ 4.317046] mmcblk0rpmb: mmc0:0001 SEM16G 4.00 MiB, chardev (236:0) <6>[ 4.720202] mmc1: new high speed SD card at address 0260 <6>[ 4.726934] mmcblk1: mmc1:0260 1232 961 MiB <6>[ 4.733344] mmcblk1: p1 p2 <6>[ 5.508765] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 5.520954] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 5.527497] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 5.533241] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 5.540383] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 5.546826] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 5.553954] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 5.561877] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 PCIe Root Port <4>[ 5.569459] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 5.579388] pci 0000:00:02.0: PCI bridge to [bus 00] <6>[ 5.584615] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff] <6>[ 5.590987] pci 0000:00:02.0: enabling Extended Tags <6>[ 5.596268] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.607031] PCI: bus0: Fast back to back transfers disabled <6>[ 5.612863] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 5.621277] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint <6>[ 5.628788] pci 0000:01:00.0: BAR 0 [io 0x0000-0x00ff] <6>[ 5.634297] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00000fff 64bit] <6>[ 5.641018] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00003fff 64bit pref] <6>[ 5.648317] pci 0000:01:00.0: supports D1 D2 <6>[ 5.652843] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.674835] PCI: bus1: Fast back to back transfers disabled <6>[ 5.680725] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 5.687781] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]: assigned <6>[ 5.695632] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref]: assigned <6>[ 5.704374] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]: assigned <6>[ 5.711517] pci 0000:01:00.0: BAR 4 [mem 0x20000000-0x20003fff 64bit pref]: assigned <6>[ 5.719642] pci 0000:01:00.0: BAR 2 [mem 0x13000000-0x13000fff 64bit]: assigned <6>[ 5.727309] pci 0000:01:00.0: BAR 0 [io 0x1000-0x10ff]: assigned <6>[ 5.733718] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 5.739026] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 5.745459] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 5.752550] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <6>[ 5.760632] pci_bus 0000:00: resource 4 [mem 0x01000000-0x01001fff] <6>[ 5.767228] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] <6>[ 5.773100] pci_bus 0000:00: resource 6 [mem 0x13000000-0x1fffffff] <6>[ 5.779694] pci_bus 0000:00: resource 7 [mem 0x20000000-0x3fffffff pref] <6>[ 5.786720] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] <6>[ 5.792587] pci_bus 0000:01: resource 1 [mem 0x13000000-0x130fffff] <6>[ 5.799189] pci_bus 0000:01: resource 2 [mem 0x20000000-0x200fffff 64bit pref] <4>[ 5.806800] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 5.814333] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 5.821139] pcieport 0000:00:02.0: PME: Signaling with IRQ 117 <6>[ 5.828339] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 5.869900] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 120 <6>[ 5.878262] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <4>[ 5.888746] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 5.896617] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 5.904383] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 5.912836] tegra-ahci 70027000.sata: AHCI vers 0001.0301, 32 command slots, 3 Gbps, platform mode <6>[ 5.922044] tegra-ahci 70027000.sata: 1/2 ports implemented (port mask 0x1) <6>[ 5.929250] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 5.938919] scsi host0: tegra-ahci <6>[ 5.942727] scsi host1: tegra-ahci <6>[ 5.946455] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 123 lpm-pol 0 <6>[ 5.955572] ata2: DUMMY <6>[ 5.958541] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 6.286712] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 6.295876] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 6.305292] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 6.334715] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC) <6>[ 6.475231] r8169 0000:01:00.0 eth0: Link is Down <6>[ 8.061341] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <5>[ 8.094679] Sending DHCP requests ., OK <6>[ 8.138870] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.212 <6>[ 8.146980] IP-Config: Complete: <6>[ 8.150493] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.212, mask=255.255.255.0, gw=192.168.0.254 <6>[ 8.161202] host=192.168.0.212, domain=shed, nis-domain=(none) <6>[ 8.167807] bootserver=192.168.0.1, rootserver=192.168.0.2, rootpath= <6>[ 8.167846] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 8.182119] clk: Disabling unused clocks <6>[ 8.186950] PM: genpd: Disabling unused power domains <6>[ 8.194092] Freeing unused kernel image (initmem) memory: 2048K <6>[ 8.200364] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.22-1~deb12u1 <6>[ 8.874794] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 8.913184] r8169 0000:01:00.0 enp1s0: renamed from eth0 (while UP) <4>[ 9.038752] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 9.048748] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 9.055266] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 9.061799] tegra-xusb 70090000.usb: probe with driver tegra-xusb failed with error -2 <6>[ 9.096817] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 101000 mC <6>[ 9.106556] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 101000 mC <6>[ 9.116491] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 101000 mC <6>[ 9.126215] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 101000 mC <6>[ 9.136135] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC <6>[ 9.146137] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 101000 mC <6>[ 9.252953] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 9.530142] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <6>[ 9.552160] input: NVIDIA Tegra Jetson TK1 Headphones Jack as /devices/soc0/sound/sound/card1/input2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/enp1s0 found done. Begin: Waiting up to 180 secs for eth0 to become available ... <6>[ 38.324865] +1.8V_RUN_CAM: disabling <6>[ 38.329019] +2.8V_RUN_CAM: disabling <6>[ 38.333118] +1.2V_RUN_CAM_FRONT: disabling <6>[ 38.337805] +1.05V_RUN_CAM_REAR: disabling <6>[ 38.342303] +3.3V_RUN_TOUCH: disabling <6>[ 38.346429] +2.8V_RUN_CAM_AF: disabling <6>[ 38.350633] +1.8V_RUN_VPP_FUSE: disabling <4>[ 69.684865] tegra-emc 7001b000.external-memory-controller: sync_state() pending due to 54200000.dc <4>[ 69.694101] tegra-mc 70019000.memory-controller: sync_state() pending due to 54200000.dc <4>[ 69.702486] tegra-emc 7001b000.external-memory-controller: sync_state() pending due to 54240000.dc <4>[ 69.711727] tegra-mc 70019000.memory-controller: sync_state() pending due to 54240000.dc # # Failure: Network device did not appear in time done. ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No<0>[ 190.413583] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 <4>[ 190.424330] CPU: 0 UID: 0 PID: 1 Comm: init Tainted: G W 6.12.0-rc5 #1 <4>[ 190.432489] Tainted: [W]=WARN <4>[ 190.435705] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) <4>[ 190.442215] Call trace: <4>[ 190.442219] unwind_backtrace from show_stack+0x10/0x14 <4>[ 190.450479] show_stack from panic+0xfc/0x344 <4>[ 190.455087] panic from make_task_dead+0x0/0x164 <0>[ 190.459960] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 ]--- such device ipconfig: no devices to configure /init: 380: .: Can't open /run/net-eth0.conf