Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.121 (1256 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 510784/tftp-deploy-jznd6re2/kernel/Image tftp 0x82000000 510784/tftp-deploy-jznd6re2/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.121; sending through gateway 172.16.0.254 Filename '510784/tftp-deploy-jznd6re2/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 16.7 MiB/s done Bytes transferred = 45713920 (2b98a00 hex) => tftp 0x90080000 510784/tftp-deploy-jznd6re2/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 510784/tftp-deploy-jznd6re2/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.121; sending through gateway 172.16.0.254 Filename '510784/tftp-deploy-jznd6re2/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################### 13.9 MiB/s done Bytes transferred = 26058708 (18d9fd4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 510784/tftp-deploy-jznd6re2/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 510784/tftp-deploy-jznd6re2/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.121; sending through gateway 172.16.0.254 Filename '510784/tftp-deploy-jznd6re2/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *### 9.5 MiB/s done Bytes transferred = 29929 (74e9 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-03 23:14:55 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 26058644 Bytes = 24.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a4e8 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.12.0-rc5 (KernelCI@build-j361057-arm64-gcc-12-defconfig-v8cxt) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Sun Nov 3 22:57:07 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550a0] enabled [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x20ff7fe6c0-0x20ff800cff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 25 pages/cpu s61656 r8192 d32552 u102400 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031680 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080040000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080050000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008882] Console: colour dummy device 80x25 <6>[ 0.013690] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024411] pid_max: default: 32768 minimum: 301 <6>[ 0.029374] LSM: initializing lsm=capability <6>[ 0.034033] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041782] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.057999] rcu: Hierarchical SRCU implementation. <6>[ 0.063113] rcu: Max phase no-delay instances is 1000. <6>[ 0.068796] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.077354] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.084286] EFI services will not be available. <6>[ 0.089228] smp: Bringing up secondary CPUs ... <6>[ 0.094357] Detected PIPT I-cache on CPU1 <6>[ 0.094401] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.094411] GICv3: CPU1: using allocated LPI pending table @0x0000002080060000 <6>[ 0.094436] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.094521] smp: Brought up 1 node, 2 CPUs <6>[ 0.124843] SMP: Total of 2 processors activated. <6>[ 0.129856] CPU: All CPU(s) started at EL2 <6>[ 0.134274] CPU features: detected: 32-bit EL0 Support <6>[ 0.139727] CPU features: detected: 32-bit EL1 Support <6>[ 0.145186] CPU features: detected: CRC32 instructions <6>[ 0.150662] alternatives: applying system-wide alternatives <6>[ 0.157391] Memory: 3871000K/4126720K available (17280K kernel code, 4898K rwdata, 11876K rodata, 10432K init, 742K bss, 218380K reserved, 32768K cma-reserved) <6>[ 0.172515] devtmpfs: initialized <6>[ 0.179757] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.189886] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.197459] 21392 pages in range for non-PLT usage <6>[ 0.197464] 512912 pages in range for PLT usage <6>[ 0.202676] pinctrl core: initialized pinctrl subsystem <6>[ 0.213550] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.221197] SoC family: QorIQ LS1028A <6>[ 0.225152] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.230538] DMI not present or invalid. <6>[ 0.236441] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.243204] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.250705] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.258944] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.267234] audit: initializing netlink subsys (disabled) <5>[ 0.273074] audit: type=2000 audit(0.164:1): state=initialized audit_enabled=0 res=1 <6>[ 0.273764] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.281168] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.287544] cpuidle: using governor menu <6>[ 0.298761] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.305911] ASID allocator initialised with 65536 entries <6>[ 0.312859] Serial: AMBA PL011 UART driver <6>[ 0.330672] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.337802] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.344399] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.351517] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.358109] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.365226] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.371818] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.378935] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.386721] ACPI: Interpreter disabled. <6>[ 0.392460] iommu: Default domain type: Translated <6>[ 0.397570] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.404256] SCSI subsystem initialized <6>[ 0.408517] usbcore: registered new interface driver usbfs <6>[ 0.414339] usbcore: registered new interface driver hub <6>[ 0.419980] usbcore: registered new device driver usb <6>[ 0.425924] i2c i2c-0: IMX I2C adapter registered <6>[ 0.431199] i2c i2c-1: IMX I2C adapter registered <6>[ 0.436630] i2c i2c-2: IMX I2C adapter registered <6>[ 0.442153] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.447445] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.456968] PTP clock support registered <6>[ 0.461268] EDAC MC: Ver: 3.0.0 <6>[ 0.464966] scmi_core: SCMI protocol bus registered <6>[ 0.470719] FPGA manager framework <6>[ 0.474480] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.481513] vgaarb: loaded <6>[ 0.484768] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.491336] VFS: Disk quotas dquot_6.6.0 <6>[ 0.495576] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.502930] pnp: PnP ACPI: disabled <6>[ 0.511215] NET: Registered PF_INET protocol family <6>[ 0.516586] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.526331] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.535260] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.543356] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.551696] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.560040] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.567001] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.574083] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.581667] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.587982] RPC: Registered named UNIX socket transport module. <6>[ 0.594235] RPC: Registered udp transport module. <6>[ 0.599248] RPC: Registered tcp transport module. <6>[ 0.604260] RPC: Registered tcp-with-tls transport module. <6>[ 0.610062] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.616836] PCI: CLS 0 bytes, default 64 <6>[ 0.621192] Unpacking initramfs... <6>[ 0.627545] kvm [1]: nv: 554 coarse grained trap handlers <6>[ 0.633673] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.639565] kvm [1]: GICv3: no GICV resource entry <6>[ 0.644682] kvm [1]: disabling GICv2 emulation <6>[ 0.649467] kvm [1]: GIC system register CPU interface enabled <6>[ 0.655649] kvm [1]: vgic interrupt IRQ9 <6>[ 0.659898] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.666587] Initialise system trusted keyrings <6>[ 0.671503] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.678494] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.688963] NFS: Registering the id_resolver key type <5>[ 0.694384] Key type id_resolver registered <5>[ 0.698880] Key type id_legacy registered <6>[ 0.703221] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.710258] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.718135] 9p: Installing v9fs 9p2000 file system support <5>[ 0.752735] Key type asymmetric registered <5>[ 0.757153] Asymmetric key parser 'x509' registered <6>[ 0.762402] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.770142] io scheduler mq-deadline registered <6>[ 0.774982] io scheduler kyber registered <6>[ 0.779332] io scheduler bfq registered <6>[ 0.791054] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.797965] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.806090] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.815255] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.824412] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.833564] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.842720] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.851875] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.861023] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.870235] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.879503] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.886812] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.892356] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.899747] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.907578] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.914983] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.922820] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.930206] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.938038] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.945463] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 0.955171] pci 0000:00:00.0: BAR 0 [mem 0x1f8000000-0x1f803ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 0.965807] pci 0000:00:00.0: BAR 2 [mem 0x1f8160000-0x1f816ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 0.976881] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81d0000-0x1f81dffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 0.987778] pci 0000:00:00.0: VF BAR 4 [mem 0x1f81f0000-0x1f81fffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 0.999141] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.004964] pci 0000:00:00.0: VF BAR 0 [mem 0x1f81d0000-0x1f81effff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.014487] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81f0000-0x1f820ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.024656] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.034366] pci 0000:00:00.1: BAR 0 [mem 0x1f8040000-0x1f807ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.045006] pci 0000:00:00.1: BAR 2 [mem 0x1f8170000-0x1f817ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.056080] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8210000-0x1f821ffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 1.066990] pci 0000:00:00.1: VF BAR 4 [mem 0x1f8230000-0x1f823ffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 1.078343] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.084158] pci 0000:00:00.1: VF BAR 0 [mem 0x1f8210000-0x1f822ffff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.093651] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8230000-0x1f824ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.103806] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.113510] pci 0000:00:00.2: BAR 0 [mem 0x1f8080000-0x1f80bffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.124149] pci 0000:00:00.2: BAR 2 [mem 0x1f8180000-0x1f818ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.135247] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.141294] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.151003] pci 0000:00:00.3: BAR 0 [mem 0x1f8100000-0x1f811ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.161640] pci 0000:00:00.3: BAR 2 [mem 0x1f8190000-0x1f819ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.172730] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.178731] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.188438] pci 0000:00:00.4: BAR 0 [mem 0x1f8120000-0x1f813ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.199087] pci 0000:00:00.4: BAR 2 [mem 0x1f81a0000-0x1f81affff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.210179] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.216214] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 PCIe Root Complex Integrated Endpoint <6>[ 1.225919] pci 0000:00:00.5: BAR 0 [mem 0x1f8140000-0x1f815ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.236561] pci 0000:00:00.5: BAR 2 [mem 0x1f81b0000-0x1f81bffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.247636] pci 0000:00:00.5: BAR 4 [mem 0x1fc000000-0x1fc3fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.258296] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.264365] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.274069] pci 0000:00:00.6: BAR 0 [mem 0x1f80c0000-0x1f80fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.284708] pci 0000:00:00.6: BAR 2 [mem 0x1f81c0000-0x1f81cffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.295796] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.302574] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 PCIe Root Complex Event Collector <6>[ 1.311954] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.319951] pci_bus 0000:00: resource 4 [mem 0x1f8000000-0x1f815ffff] <6>[ 1.326729] pci_bus 0000:00: resource 5 [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.333939] pci_bus 0000:00: resource 6 [mem 0x1f81d0000-0x1f81effff] <6>[ 1.340709] pci_bus 0000:00: resource 7 [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.347921] pci_bus 0000:00: resource 8 [mem 0x1f8210000-0x1f822ffff] <6>[ 1.354693] pci_bus 0000:00: resource 9 [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.361902] pci_bus 0000:00: resource 10 [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.472800] pci 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 1.479656] pci 0000:00:00.1: enetc_fixup_clear_rss_rfs+0x0/0x5c took 108241 usecs <6>[ 1.515490] Freeing initrd memory: 25440K <6>[ 1.588785] pci 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 1.595102] pci 0000:00:00.2: enetc_fixup_clear_rss_rfs+0x0/0x5c took 104949 usecs <6>[ 1.704783] pci 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 1.711058] pci 0000:00:00.6: enetc_fixup_clear_rss_rfs+0x0/0x5c took 105460 usecs <6>[ 1.719008] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.727180] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.733480] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.740151] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.747825] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.756710] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.765629] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 2.732776] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.739181] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.746221] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.752027] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.758534] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.769446] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 2.777110] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.782698] pci 0001:00:00.0: supports D1 D2 <6>[ 2.787274] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.794573] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.800124] pci_bus 0001:00: resource 4 [io 0x0000-0xffff] <6>[ 2.806017] pci_bus 0001:00: resource 5 [mem 0x8040000000-0x807fffffff] <6>[ 2.813079] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.820751] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.829639] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.838557] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.804777] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.811173] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.818209] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.824015] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.833329] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.844237] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 3.851900] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.857486] pci 0002:00:00.0: supports D1 D2 <6>[ 3.862062] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.869313] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.874862] pci_bus 0002:00: resource 4 [io 0x10000-0x1ffff] <6>[ 3.880930] pci_bus 0002:00: resource 5 [mem 0x8840000000-0x887fffffff] <6>[ 3.907696] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.916133] printk: legacy console [ttyS0] disabled <6>[ 3.921514] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.930682] printk: legacy console [ttyS0] enabled <6>[ 3.930682] printk: legacy console [ttyS0] enabled <6>[ 3.940859] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.940859] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.957364] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.967331] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.977393] msm_serial: driver initialized <6>[ 3.981992] SuperH (H)SCI(F) driver initialized <6>[ 3.986913] STM32 USART driver initialized <5>[ 3.994713] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.001457] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.006355] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.011954] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.017555] arm-smmu 5000000.iommu: nested translation <5>[ 4.023062] arm-smmu 5000000.iommu: coherent table walk <5>[ 4.028660] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 4.036265] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.043696] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.050522] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.057255] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.063985] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.070937] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 4.077113] arm-smmu 5000000.iommu: Failed to disable prefetcher for errata workarounds, check SACR.CACHE_LOCK <6>[ 4.090823] loop: module loaded <6>[ 4.102521] megasas: 07.727.03.00-rc1 <5>[ 4.140651] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.147759] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.153271] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.158986] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.166157] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.173221] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.179456] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.189622] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.195639] thunder_xcv, ver 1.0 <6>[ 4.199174] thunder_bgx, ver 1.0 <6>[ 4.202697] nicpf, ver 1.0 <6>[ 4.206457] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 0 <6>[ 4.316784] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.341554] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 1 <6>[ 4.347872] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.354824] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.363855] pps pps0: new PPS source ptp0 <6>[ 4.368690] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.376220] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.381880] hclge is initializing <6>[ 4.385490] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.390652] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.396705] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.401954] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.408180] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.413861] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.419734] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.426289] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.432743] sky2: driver version 1.30 <6>[ 4.437701] VFIO - User Level meta-driver version: 0.3 <6>[ 4.443464] dwc3 3100000.usb: Adding to iommu group 2 <6>[ 4.449737] dwc3 3110000.usb: Adding to iommu group 3 <6>[ 4.457618] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.463419] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.471493] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.481200] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x03100000 <6>[ 4.487495] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.493268] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.501219] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.508415] hub 1-0:1.0: USB hub found <6>[ 4.512461] hub 1-0:1.0: 1 port detected <6>[ 4.516872] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.525551] hub 2-0:1.0: USB hub found <6>[ 4.529594] hub 2-0:1.0: 1 port detected <6>[ 4.534022] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.539817] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.547885] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.557615] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03110000 <6>[ 4.563909] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.569690] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.577647] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.584817] hub 3-0:1.0: USB hub found <6>[ 4.588872] hub 3-0:1.0: 1 port detected <6>[ 4.593259] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.601943] hub 4-0:1.0: USB hub found <6>[ 4.605985] hub 4-0:1.0: 1 port detected <6>[ 4.610751] usbcore: registered new interface driver usb-storage <6>[ 4.619285] i2c_dev: i2c /dev entries driver <6>[ 4.627599] sp805-wdt c000000.watchdog: registration successful <6>[ 4.633994] sp805-wdt c010000.watchdog: registration successful <6>[ 4.642351] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.651312] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.657791] sdhci: Copyright(c) Pierre Ossman <6>[ 4.662979] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.670009] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.676631] sdhci-esdhc 2150000.mmc: Adding to iommu group 4 <6>[ 4.682749] sdhci-esdhc 2140000.mmc: Adding to iommu group 5 <6>[ 4.682963] usbcore: registered new interface driver usbhid <6>[ 4.694577] usbhid: USB HID core driver <6>[ 4.704937] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 (0,8000003f) counters available <6>[ 4.718791] NET: Registered PF_PACKET protocol family <6>[ 4.724202] 9pnet: Installing 9P2000 support <6>[ 4.728788] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.728857] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <5>[ 4.736021] Key type dns_resolver registered <6>[ 4.753945] registered taskstats version 1 <5>[ 4.758398] Loading compiled-in X.509 certificates <6>[ 4.768507] Demotion targets for Node 0: null <6>[ 4.775714] fsl-edma 22c0000.dma-controller: Adding to iommu group 6 <6>[ 4.783576] pcieport 0001:00:00.0: Adding to iommu group 7 <6>[ 4.789616] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.795932] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.802063] pcieport 0002:00:00.0: Adding to iommu group 8 <6>[ 4.808008] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.814289] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.823097] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.848846] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.855980] mmc0: new HS400 MMC card at address 0001 <6>[ 4.861647] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.867739] mmcblk0: p1 p2 <6>[ 4.871230] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.877446] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.883483] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 5.032943] hub 3-1:1.0: USB hub found <6>[ 5.037099] hub 3-1:1.0: 7 ports detected <6>[ 17.096967] clk: Disabling unused clocks <6>[ 17.101338] PM: genpd: Disabling unused power domains <6>[ 17.106730] ALSA device list: <6>[ 17.110015] No soundcards found. <6>[ 17.123862] Freeing unused kernel memory: 10432K <6>[ 17.128998] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 17.201062] udevd[107]: starting version 3.2.9 <5>[ 18.328784] random: crng init done <27>[ 18.335258] udevd[107]: specified user 'tss' unknown <27>[ 18.340669] udevd[107]: specified group 'tss' unknown <30>[ 18.347013] udevd[108]: starting eudev-3.2.9 <6>[ 18.604900] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 18.622945] fsl_ddr_edac acquired irq 108 for MC <6>[ 18.642159] fsl_ddr_edac MC err registered <4>[ 18.647253] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 18.655540] NET: Registered PF_INET6 protocol family <4>[ 18.657732] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 18.688991] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 18.695563] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.702926] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 18.710254] Segment Routing with IPv6 <6>[ 18.714833] In-situ OAM (IOAM) with IPv6 <6>[ 18.720154] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 18.733122] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 18.733502] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 18.743142] rtc-rv8803 0-0032: registered as rtc0 <6>[ 18.749769] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 18.764702] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.772411] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 18.783526] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <3>[ 18.792956] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 18.801260] wm8904 2-001a: revision A <6>[ 18.816220] input: buttons1 as /devices/platform/buttons1/input/input12 <6>[ 18.848165] CAN device driver interface <6>[ 18.897645] caam 8000000.crypto: Entropy delay = 3200 <6>[ 18.903332] ftm-alarm 2800000.rtc: registered as rtc1 <6>[ 18.927487] usbcore: registered new device driver onboard-usb-dev <6>[ 18.952361] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 18.969334] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 18.969576] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 18.980932] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 18.988611] caam 8000000.crypto: job rings = 4, qi = 0 <4>[ 18.993251] sysfs: cannot create duplicate filename '/devices/platform/sound/sai-tx-rx-wm8904-hifi' <6>[ 18.999483] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <4>[ 19.009966] CPU: 0 UID: 0 PID: 115 Comm: udevd Not tainted 6.12.0-rc5 #1 <4>[ 19.016961] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT) <4>[ 19.025515] Call trace: <4>[ 19.028225] dump_backtrace+0x94/0xec <4>[ 19.032169] show_stack+0x18/0x24 <4>[ 19.035758] dump_stack_lvl+0x78/0x90 <4>[ 19.039693] dump_stack+0x18/0x24 <4>[ 19.043277] sysfs_warn_dup+0x64/0x80 <4>[ 19.047212] sysfs_create_dir_ns+0xec/0x10c <4>[ 19.051668] kobject_add_internal+0x98/0x26c <4>[ 19.056215] kobject_add+0x9c/0x10c <4>[ 19.059975] device_add+0xc0/0x790 <4>[ 19.063648] device_register+0x20/0x30 <4>[ 19.067669] snd_soc_add_pcm_runtimes+0x328/0x850 <4>[ 19.072651] snd_soc_bind_card+0x2d4/0xbb0 <4>[ 19.077021] snd_soc_register_card+0xf0/0x108 <4>[ 19.081653] devm_snd_soc_register_card+0x4c/0xa4 <4>[ 19.086635] simple_probe+0x21c/0x3e8 [snd_soc_simple_card] <4>[ 19.092494] platform_probe+0x68/0xc4 <4>[ 19.096428] really_probe+0xbc/0x298 <4>[ 19.100276] __driver_probe_device+0x78/0x12c <4>[ 19.104909] driver_probe_device+0xd8/0x15c <4>[ 19.109368] __driver_attach+0x94/0x19c <4>[ 19.113477] bus_for_each_dev+0x78/0xd4 <4>[ 19.117586] driver_attach+0x24/0x30 <4>[ 19.121433] bus_add_driver+0xe4/0x208 <4>[ 19.125455] driver_register+0x60/0x128 <4>[ 19.129565] __platform_driver_register+0x24/0x30 <4>[ 19.134545] simple_card_init+0x20/0x1000 [snd_soc_simple_card] <4>[ 19.140747] do_one_initcall+0x80/0x1c4 <4>[ 19.144855] do_init_module+0x60/0x1f0 <4>[ 19.148876] load_module+0x1ca0/0x1dc4 <4>[ 19.152895] init_module_from_file+0x84/0xc4 <4>[ 19.157439] __arm64_sys_finit_module+0x148/0x31c <4>[ 19.162418] invoke_syscall+0x48/0x110 <4>[ 19.166442] el0_svc_common.constprop.0+0x40/0xe0 <4>[ 19.171424] do_el0_svc+0x1c/0x28 <4>[ 19.175010] el0_svc+0x34/0xdc <4>[ 19.178334] el0t_64_sync_handler+0x100/0x12c <4>[ 19.182966] el0t_64_sync+0x190/0x194 <6>[ 19.189464] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <6>[ 19.201248] mali-dp f080000.display: Adding to iommu group 9 <3>[ 19.206454] kobject: kobject_add_internal failed for sai-tx-rx-wm8904-hifi with -EEXIST, don't try to register things with the same name in the same directory. <3>[ 19.222633] asoc-simple-card sound: probe with driver asoc-simple-card failed with error -12 <6>[ 19.290086] caam_jr 8010000.jr: Adding to iommu group 10 <6>[ 19.308889] caam algorithms registered in /proc/crypto <6>[ 19.314391] caam 8000000.crypto: registering rng-caam <6>[ 19.319880] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.327113] caam_jr 8020000.jr: Adding to iommu group 11 <6>[ 19.333461] caam_jr 8030000.jr: Adding to iommu group 12 <6>[ 19.339720] caam_jr 8040000.jr: Adding to iommu group 13 done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-510784/environment . /lava-510784/environment / # /lava-510784/bin/lava-test-runner /lava-510784/0 /lava-510784/bin/lava-test-runner /lava-510784/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 19.951968] d /lava-510784/0/tests/0_dmesg + cat uuid + UUID=510784_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.973011] <8>[ 19.994962] <8>[ 20.018124] + set +x <8>[ 20.027889] / #