Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot 2019.04-linux4sam_6.2-icp (May 18 2022 - 22:17:10 +0000), Build: HEAD-0.00-20220518221710 CPU: SAMA7 Reset Source : SYSRESET Watchdog enabled DRAM: 1 GiB MMC: emmc@e0830000: 0 Loading Environment from SPI Flash... SF: Detected sst26vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial VPD: BOARD_SERIAL K1FT90005, MAC 00:A0:A5:5C:6D:A2 Net: eth0: port0 [PRIME], eth1: port1, eth2: port2, eth3: port3, eth4: port4, eth5: port5, eth6: port6, eth7: port7 POST memory PASSED POST env PASSED POST vpd PASSED => setenv autoload no setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp dhcp port4 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 DHCP client bound to address 172.16.0.126 (1759 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x62000000 512798/tftp-deploy-nhrg_t4w/kernel/zImage tftp 0x62000000 512798/tftp-deploy-nhrg_t4w/kernel/zImage tftp 0x62000000 512798/tftp-deploy-nhrg_t4w/kernel/zImage port4 Waiting for PHY auto negotiation to complete...... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '512798/tftp-deploy-nhrg_t4w/kernel/zImage'. Load address: 0x62000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 1.6 MiB/s done Bytes transferred = 10789376 (a4a200 hex) => tftp 0x68080000 512798/tftp-deploy-nhrg_t4w/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 512798/tftp-deploy-nhrg_t4w/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 512798/tftp-deploy-nhrg_t4w/ramdisk/ramdisk.cpio.gz.uboot port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '512798/tftp-deploy-nhrg_t4w/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################### 2.4 MiB/s done Bytes transferred = 17483186 (10ac5b2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x68000000 512798/tftp-deploy-nhrg_t4w/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb tftp 0x68000000 512798/tftp-deploy-nhrg_t4w/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb tftp 0x68000000 512798/tftp-deploy-nhrg_t4w/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '512798/tftp-deploy-nhrg_t4w/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb'. Load address: 0x68000000 Loading: *# 2 KiB/s done Bytes transferred = 14136 (3738 hex) => setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 ## Loading init Ramdisk from Legacy Image at 68080000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17483122 Bytes = 16.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Using Device Tree in place at 68000000, end 68006737 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j367820-arm-gcc-12-multi-v7-defconfig-config-thumb2-49vnm) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Fri Nov 8 01:22:32 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Kontron KSwitch D10 MMT 6G-2GS [ 0.000000] earlycon: atmel_serial0 at MMIO 0xe0040200 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000008fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000090000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40844 r8192 d20596 u69632 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 37.50MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x8a60dd6a9, max_idle_ns: 440795204056 ns <6>[ 0.000002] sched_clock: 56 bits at 38MHz, resolution 26ns, wraps every 2199023255540ns <6>[ 0.008280] Switching to timer-based delay loop, resolution 26ns <6>[ 0.017461] Console: colour dummy device 80x30 <6>[ 0.022136] Calibrating delay loop (skipped), value calculated using timer frequency.. 75.00 BogoMIPS (lpj=375000) <6>[ 0.032720] CPU: Testing write buffer coherency: ok <6>[ 0.037837] pid_max: default: 32768 minimum: 301 <6>[ 0.042967] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.050442] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.059940] CPU0: update cpu_capacity 1024 <6>[ 0.064194] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.130503] Setting up static identity map for 0x60300000 - 0x603000a0 <6>[ 0.138230] rcu: Hierarchical SRCU implementation. <6>[ 0.143210] rcu: Max phase no-delay instances is 1000. <6>[ 0.151054] EFI services will not be available. <6>[ 0.156115] smp: Bringing up secondary CPUs ... <6>[ 0.160809] smp: Brought up 1 node, 1 CPU <6>[ 0.165049] SMP: Total of 1 processors activated (75.00 BogoMIPS). <6>[ 0.171601] CPU: All CPU(s) started in SVC mode. <6>[ 0.176545] Memory: 930080K/1048576K available (11264K kernel code, 2543K rwdata, 6788K rodata, 2048K init, 430K bss, 50696K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.193002] devtmpfs: initialized <6>[ 0.202590] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.210802] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.220883] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.232473] pinctrl core: initialized pinctrl subsystem <6>[ 0.240779] DMI not present or invalid. <6>[ 0.246661] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.255998] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.266648] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.266799] cpuidle: using governor menu <6>[ 0.277678] No ATAGs? <6>[ 0.280158] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.288411] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.297650] Serial: AMBA PL011 UART driver <6>[ 0.319526] platform e2004064.pinctrl: Fixed dependency cycle(s) with /soc/pinctrl@e2004064/phy-int-pins <6>[ 0.355200] at_xdmac e0068000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.366496] iommu: Default domain type: Translated <6>[ 0.371435] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.409699] SCSI subsystem initialized <6>[ 0.419365] usbcore: registered new interface driver usbfs <6>[ 0.425042] usbcore: registered new interface driver hub <6>[ 0.430690] usbcore: registered new device driver usb <6>[ 0.437492] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.442641] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.452037] PTP clock support registered <6>[ 0.456434] EDAC MC: Ver: 3.0.0 <6>[ 0.507620] scmi_core: SCMI protocol bus registered <6>[ 0.516392] vgaarb: loaded <6>[ 0.534647] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.565555] NET: Registered PF_INET protocol family <6>[ 0.570994] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.582201] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.590795] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.598777] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.606904] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.614683] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.621353] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.628230] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.635786] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.726937] RPC: Registered named UNIX socket transport module. <6>[ 0.733019] RPC: Registered udp transport module. <6>[ 0.738037] RPC: Registered tcp transport module. <6>[ 0.742958] RPC: Registered tcp-with-tls transport module. <6>[ 0.748734] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.755462] PCI: CLS 0 bytes, default 64 <5>[ 0.761475] Initialise system trusted keyrings <6>[ 0.783321] Trying to unpack rootfs image as initramfs... <6>[ 0.845087] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.852335] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.891818] NFS: Registering the id_resolver key type <5>[ 0.897180] Key type id_resolver registered <5>[ 0.901499] Key type id_legacy registered <6>[ 0.905859] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.912749] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.981887] Key type asymmetric registered <5>[ 0.986203] Asymmetric key parser 'x509' registered <6>[ 0.991440] bounce: pool size: 64 pages <6>[ 0.995523] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.003080] io scheduler mq-deadline registered <6>[ 1.007946] io scheduler kyber registered <6>[ 1.012191] io scheduler bfq registered <6>[ 1.115433] pinctrl-ocelot e2004064.pinctrl: driver registered <6>[ 1.175842] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.577872] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.622536] msm_serial: driver initialized <6>[ 1.627427] SuperH (H)SCI(F) driver initialized <6>[ 1.632380] STMicroelectronics ASC driver initialized <6>[ 1.637826] STM32 USART driver initialized <5>[ 1.725313] random: crng init done <6>[ 1.791456] brd: module loaded <6>[ 1.814736] loop: module loaded <6>[ 1.824533] atmel_usart_serial atmel_usart_serial.0.auto: Using FIFO (32 data) <6>[ 1.832852] atmel_usart_serial.0.auto: ttyAT0 at MMIO 0xe0040200 (irq = 32, base_baud = 12500000) is a ATMEL_SERIAL <6>[ 1.843593] printk: legacy console [ttyAT0] enabled <6>[ 1.843593] printk: legacy console [ttyAT0] enabled <6>[ 1.853760] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 1.853760] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 2.057012] CAN device driver interface <6>[ 2.062454] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.069853] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.075102] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.081323] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.086980] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.098399] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.104265] usbcore: registered new interface driver pegasus <6>[ 2.110284] usbcore: registered new interface driver asix <6>[ 2.115999] usbcore: registered new interface driver ax88179_178a <6>[ 2.122373] usbcore: registered new interface driver cdc_ether <6>[ 2.128505] usbcore: registered new interface driver smsc75xx <6>[ 2.134516] usbcore: registered new interface driver smsc95xx <6>[ 2.140567] usbcore: registered new interface driver net1080 <6>[ 2.146510] usbcore: registered new interface driver cdc_subset <6>[ 2.152695] usbcore: registered new interface driver zaurus <6>[ 2.158563] usbcore: registered new interface driver cdc_ncm <6>[ 2.169924] usbcore: registered new interface driver usb-storage <6>[ 2.183310] i2c_dev: i2c /dev entries driver <6>[ 2.561605] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.568145] sdhci: Copyright(c) Pierre Ossman <6>[ 2.575391] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.583811] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.595479] usbcore: registered new interface driver usbhid <6>[ 2.601296] usbhid: USB HID core driver <6>[ 2.614771] NET: Registered PF_INET6 protocol family <6>[ 2.806708] Segment Routing with IPv6 <6>[ 2.810672] In-situ OAM (IOAM) with IPv6 <6>[ 2.815041] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.822243] NET: Registered PF_PACKET protocol family <6>[ 2.827612] can: controller area network core <6>[ 2.832259] NET: Registered PF_CAN protocol family <6>[ 2.837303] can: raw protocol <6>[ 2.840502] can: broadcast manager protocol <6>[ 2.844973] can: netlink gateway - max_hops=1 <5>[ 2.850331] Key type dns_resolver registered <6>[ 2.855229] ThumbEE CPU extension supported. <5>[ 2.859737] Registering SWP/SWPB emulation handler <5>[ 3.069444] Loading compiled-in X.509 certificates <6>[ 5.596044] Freeing initrd memory: 17076K <6>[ 15.614791] clk: Disabling unused clocks <6>[ 15.618974] PM: genpd: Disabling unused power domains <6>[ 15.630165] Freeing unused kernel image (initmem) memory: 2048K <6>[ 15.634112] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.875047] udevd[73]: starting version 3.2.9 <27>[ 15.893169] udevd[73]: specified user 'tss' unknown <27>[ 15.896249] udevd[73]: specified group 'tss' unknown <30>[ 15.914932] udevd[74]: starting eudev-3.2.9 <6>[ 17.714152] atmel_aes e004c000.crypto: version: 0x702 <6>[ 17.780850] MAC addr was not set, use random MAC <6>[ 17.805494] atmel_aes e004c000.crypto: Atmel AES - Using dma0chan0, dma0chan1 for DMA transfers <6>[ 17.906811] atmel_spi e0064400.spi: Using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfers <6>[ 17.912960] atmel_spi e0064400.spi: Using FIFO (32 data) <6>[ 17.926573] at91_i2c e0044600.i2c: using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <6>[ 17.942553] atmel_sha e006c000.crypto: version: 0x700 <6>[ 17.985833] at91_i2c e0044600.i2c: AT91 i2c bus driver (hw version: 0x820). <6>[ 17.999952] sfp sfp1: Host maximum power 2.5W <6>[ 18.020512] atmel_spi e0064400.spi: Atmel SPI Controller version 0x401 at 0xe0064400 (irq 36) <6>[ 18.045001] atmel_sha e006c000.crypto: using dma0chan6 for DMA transfers <6>[ 18.049318] atmel_sha e006c000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 18.074877] at91_i2c e0070600.i2c: using dma0chan7 (tx) and dma0chan8 (rx) for DMA transfers <6>[ 18.125825] at91_i2c e0070600.i2c: AT91 i2c bus driver (hw version: 0x820). <6>[ 18.200758] sfp sfp0: Host maximum power 2.5W <6>[ 18.290282] MAC addr was not set, use random MAC <6>[ 18.301981] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 18.320994] sfp sfp1: module AGILENT HFBR-5710L rev sn 0304140555048996 dc 030414 <6>[ 18.503970] lan966x-switch e0000000.switch (unnamed net_device) (uninitialized): switched to inband/1000base-x link mode <6>[ 18.527410] sfp sfp0: module AGILENT HFBR-5710L rev sn 0304140604014998 dc 030414 <6>[ 18.534397] lan966x-switch e0000000.switch eth2: switched to inband/1000base-x link mode done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # # / # export SHELL=/bin/sh export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-512798/environment . /lava-512798/environment . /lava-512798/environment / # /lava-512798/bin/lava-test-runner /lava-512798/0 /lava-512798/bin/lava-test-runner /lava-512798/0 /lava-512798/bin/lava-test-runner /lava-512798/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-512798/0/tests/0_dmesg + cat uuid + UUID=512798_1.5.2.4.1 + set +x <8>[ 21.981156] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.051241] <8>[ 22.113420] <8>[ 22.176484] + set +x <8>[ 22.185613] / #