Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot 2019.04-linux4sam_6.2-icp (Jul 22 2022 - 14:29:27 +0000), Build: BETA-1.03-20220722142927 CPU: SAMA7 Reset Source : SYSRESET Watchdog enabled DRAM: 1 GiB MMC: emmc@e0830000: 0 Loading Environment from SPI Flash... SF: Detected sst26vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial VPD: BOARD_SERIAL K1FT80003, MAC 00:A0:A5:5C:6D:96 Net: eth0: port0 [PRIME], eth1: port1, eth2: port2, eth3: port3, eth4: port4, eth5: port5, eth6: port6, eth7: port7 POST memory PASSED POST env PASSED POST vpd PASSED => setenv autoload no setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp dhcp port4 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 DHCP client bound to address 172.16.0.109 (1759 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x62000000 513334/tftp-deploy-zcz9qevn/kernel/zImage tftp 0x62000000 513334/tftp-deploy-zcz9qevn/kernel/zImage tftp 0x62000000 513334/tftp-deploy-zcz9qevn/kernel/zImage port4 Waiting for PHY auto negotiation to complete..... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.109; sending through gateway 172.16.0.254 Filename '513334/tftp-deploy-zcz9qevn/kernel/zImage'. Load address: 0x62000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################### 1.8 MiB/s done Bytes transferred = 12042752 (b7c200 hex) => tftp 0x68080000 513334/tftp-deploy-zcz9qevn/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 513334/tftp-deploy-zcz9qevn/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 513334/tftp-deploy-zcz9qevn/ramdisk/ramdisk.cpio.gz.uboot port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.109; sending through gateway 172.16.0.254 Filename '513334/tftp-deploy-zcz9qevn/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 2.4 MiB/s done Bytes transferred = 18491778 (11a2982 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x68000000 513334/tftp-deploy-zcz9qevn/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb tftp 0x68000000 513334/tftp-deploy-zcz9qevn/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb tftp 0x68000000 513334/tftp-deploy-zcz9qevn/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.109; sending through gateway 172.16.0.254 Filename '513334/tftp-deploy-zcz9qevn/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb'. Load address: 0x68000000 Loading: *# 2 KiB/s done Bytes transferred = 13227 (33ab hex) => setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 ## Loading init Ramdisk from Legacy Image at 68080000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 18491714 Bytes = 17.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Using Device Tree in place at 68000000, end 680063aa Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j370111-arm-clang-16-multi-v7-defconfig-5q2kc) (Debian clang version 16.0.6 (15~deb12u1), Debian LLD 16.0.6) #1 SMP Fri Nov 8 22:26:11 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Kontron KSwitch D10 MMT 8G [ 0.000000] earlycon: atmel_serial0 at MMIO 0xe0040200 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000008fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000090000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40716 r8192 d20724 u69632 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 37.50MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x8a60dd6a9, max_idle_ns: 440795204056 ns <6>[ 0.000003] sched_clock: 56 bits at 38MHz, resolution 26ns, wraps every 2199023255540ns <6>[ 0.008280] Switching to timer-based delay loop, resolution 26ns <6>[ 0.017719] Console: colour dummy device 80x30 <6>[ 0.022411] Calibrating delay loop (skipped), value calculated using timer frequency.. 75.00 BogoMIPS (lpj=375000) <6>[ 0.032993] CPU: Testing write buffer coherency: ok <6>[ 0.038109] pid_max: default: 32768 minimum: 301 <6>[ 0.043268] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.050751] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.060412] CPU0: update cpu_capacity 1024 <6>[ 0.064668] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.131059] Setting up static identity map for 0x60300000 - 0x603000ac <6>[ 0.138893] rcu: Hierarchical SRCU implementation. <6>[ 0.143897] rcu: Max phase no-delay instances is 1000. <6>[ 0.151997] EFI services will not be available. <6>[ 0.157140] smp: Bringing up secondary CPUs ... <6>[ 0.161857] smp: Brought up 1 node, 1 CPU <6>[ 0.166089] SMP: Total of 1 processors activated (75.00 BogoMIPS). <6>[ 0.172665] CPU: All CPU(s) started in SVC mode. <6>[ 0.177608] Memory: 922960K/1048576K available (17408K kernel code, 2538K rwdata, 6696K rodata, 2048K init, 432K bss, 57816K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.194230] devtmpfs: initialized <6>[ 0.204170] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.212430] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.222541] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.233561] pinctrl core: initialized pinctrl subsystem <6>[ 0.242134] DMI not present or invalid. <6>[ 0.248507] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.257330] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.268348] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.268539] cpuidle: using governor menu <6>[ 0.279504] No ATAGs? <6>[ 0.282011] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.290252] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.299785] Serial: AMBA PL011 UART driver <6>[ 0.320481] platform e2004064.pinctrl: Fixed dependency cycle(s) with /soc/pinctrl@e2004064/phy-int-pins <6>[ 0.358578] at_xdmac e0068000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.370002] iommu: Default domain type: Translated <6>[ 0.374943] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.413332] SCSI subsystem initialized <6>[ 0.422422] usbcore: registered new interface driver usbfs <6>[ 0.428113] usbcore: registered new interface driver hub <6>[ 0.433757] usbcore: registered new device driver usb <6>[ 0.440601] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.445786] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.455166] PTP clock support registered <6>[ 0.459556] EDAC MC: Ver: 3.0.0 <6>[ 0.510032] scmi_core: SCMI protocol bus registered <6>[ 0.530072] vgaarb: loaded <6>[ 0.533832] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.585430] NET: Registered PF_INET protocol family <6>[ 0.590912] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.602185] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.610822] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.618786] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.626910] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.634687] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.641369] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.648291] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.655856] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.748039] RPC: Registered named UNIX socket transport module. <6>[ 0.754200] RPC: Registered udp transport module. <6>[ 0.759101] RPC: Registered tcp transport module. <6>[ 0.764107] RPC: Registered tcp-with-tls transport module. <6>[ 0.769826] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.776581] PCI: CLS 0 bytes, default 64 <5>[ 0.782727] Initialise system trusted keyrings <6>[ 0.809770] Trying to unpack rootfs image as initramfs... <6>[ 0.864363] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.871714] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.914622] NFS: Registering the id_resolver key type <5>[ 0.919953] Key type id_resolver registered <5>[ 0.924395] Key type id_legacy registered <6>[ 0.928638] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.935606] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 1.004876] Key type asymmetric registered <5>[ 1.009146] Asymmetric key parser 'x509' registered <6>[ 1.014526] bounce: pool size: 64 pages <6>[ 1.018611] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.026222] io scheduler mq-deadline registered <6>[ 1.030967] io scheduler kyber registered <6>[ 1.035330] io scheduler bfq registered <6>[ 1.144431] pinctrl-ocelot e2004064.pinctrl: driver registered <6>[ 1.188422] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.667875] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.691084] msm_serial: driver initialized <6>[ 1.696072] SuperH (H)SCI(F) driver initialized <6>[ 1.701043] STMicroelectronics ASC driver initialized <6>[ 1.706489] STM32 USART driver initialized <5>[ 1.783647] random: crng init done <6>[ 1.867442] brd: module loaded <6>[ 1.906959] loop: module loaded <6>[ 1.917151] atmel_usart_serial atmel_usart_serial.0.auto: Using FIFO (32 data) <6>[ 1.925623] atmel_usart_serial.0.auto: ttyAT0 at MMIO 0xe0040200 (irq = 32, base_baud = 12500000) is a ATMEL_SERIAL <6>[ 1.936412] printk: legacy console [ttyAT0] enabled <6>[ 1.936412] printk: legacy console [ttyAT0] enabled <6>[ 1.946612] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 1.946612] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 2.135281] CAN device driver interface <6>[ 2.140646] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.148042] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.153238] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.159576] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.165230] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.176538] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.182425] usbcore: registered new interface driver pegasus <6>[ 2.188455] usbcore: registered new interface driver asix <6>[ 2.194161] usbcore: registered new interface driver ax88179_178a <6>[ 2.200531] usbcore: registered new interface driver cdc_ether <6>[ 2.206685] usbcore: registered new interface driver smsc75xx <6>[ 2.212707] usbcore: registered new interface driver smsc95xx <6>[ 2.218754] usbcore: registered new interface driver net1080 <6>[ 2.224714] usbcore: registered new interface driver cdc_subset <6>[ 2.230918] usbcore: registered new interface driver zaurus <6>[ 2.236801] usbcore: registered new interface driver cdc_ncm <6>[ 2.248240] usbcore: registered new interface driver usb-storage <6>[ 2.261716] i2c_dev: i2c /dev entries driver <6>[ 2.623606] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.630237] sdhci: Copyright(c) Pierre Ossman <6>[ 2.637405] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.646037] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.657792] usbcore: registered new interface driver usbhid <6>[ 2.663613] usbhid: USB HID core driver <6>[ 2.677370] NET: Registered PF_INET6 protocol family <6>[ 2.826190] Segment Routing with IPv6 <6>[ 2.830160] In-situ OAM (IOAM) with IPv6 <6>[ 2.834596] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.841965] NET: Registered PF_PACKET protocol family <6>[ 2.847357] can: controller area network core <6>[ 2.852015] NET: Registered PF_CAN protocol family <6>[ 2.857077] can: raw protocol <6>[ 2.860265] can: broadcast manager protocol <6>[ 2.864742] can: netlink gateway - max_hops=1 <5>[ 2.870112] Key type dns_resolver registered <6>[ 2.875059] ThumbEE CPU extension supported. <5>[ 2.879581] Registering SWP/SWPB emulation handler <5>[ 3.084927] Loading compiled-in X.509 certificates <6>[ 5.319441] Freeing initrd memory: 18060K <6>[ 15.614000] clk: Disabling unused clocks <6>[ 15.618207] PM: genpd: Disabling unused power domains <6>[ 15.628692] Freeing unused kernel image (initmem) memory: 2048K <6>[ 15.632822] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.902336] udevd[74]: starting version 3.2.9 <27>[ 15.921979] udevd[74]: specified user 'tss' unknown <27>[ 15.925223] udevd[74]: specified group 'tss' unknown <30>[ 15.944893] udevd[75]: starting eudev-3.2.9 <6>[ 17.932380] MAC addr was not set, use random MAC <6>[ 18.015042] atmel_aes e004c000.crypto: version: 0x702 <6>[ 18.021364] atmel_sha e006c000.crypto: version: 0x700 <6>[ 18.027503] atmel_aes e004c000.crypto: Atmel AES - Using dma0chan0, dma0chan1 for DMA transfers <6>[ 18.038771] atmel_sha e006c000.crypto: using dma0chan2 for DMA transfers <6>[ 18.043098] atmel_sha e006c000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 18.142520] atmel_spi e0064400.spi: Using dma0chan3 (tx) and dma0chan4 (rx) for DMA transfers <6>[ 18.148836] atmel_spi e0064400.spi: Using FIFO (32 data) <6>[ 18.204091] atmel_spi e0064400.spi: Atmel SPI Controller version 0x401 at 0xe0064400 (irq 39) <6>[ 18.316667] MAC addr was not set, use random MAC <6>[ 18.359811] hwmon hwmon0: temp1_input not attached to any thermal zone done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # # / # export SHELL=/bin/sh export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-513334/environment . /lava-513334/environment . /lava-513334/environment / # /lava-513334/bin/lava-test-runner /lava-513334/0 /lava-513334/bin/lava-test-runner /lava-513334/0 /lava-513334/bin/lava-test-runner /lava-513334/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-513334/0/tests/0_dmesg + cat uuid + UUID=513334_1.5.2.4.1 + set +x <8>[ 22.377517] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.454974] <8>[ 22.523073] <8>[ 22.592019] + set +x <8>[ 22.601013] / #