Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.95 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 511365/tftp-deploy-pbg9t3_w/kernel/Image tftp 0x82000000 511365/tftp-deploy-pbg9t3_w/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.95; sending through gateway 172.16.0.254 Filename '511365/tftp-deploy-pbg9t3_w/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 14 MiB/s done Bytes transferred = 45713920 (2b98a00 hex) => tftp 0x90080000 511365/tftp-deploy-pbg9t3_w/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 511365/tftp-deploy-pbg9t3_w/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.95; sending through gateway 172.16.0.254 Filename '511365/tftp-deploy-pbg9t3_w/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################### 6.1 MiB/s done Bytes transferred = 26065491 (18dba53 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 511365/tftp-deploy-pbg9t3_w/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 511365/tftp-deploy-pbg9t3_w/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.95; sending through gateway 172.16.0.254 Filename '511365/tftp-deploy-pbg9t3_w/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *### 7.1 MiB/s done Bytes transferred = 29585 (7391 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-05 3:46:25 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 26065427 Bytes = 24.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a390 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j362590-arm64-gcc-12-defconfig-c29mz) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Tue Nov 5 03:22:17 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550a0] enabled [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x20ff7dda80-0x20ff7e00bf] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 on node -1 [ 0.000000] percpu: Embedded 25 pages/cpu s61656 r8192 d32552 u102400 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1048576 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080040000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080050000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008847] Console: colour dummy device 80x25 <6>[ 0.013655] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024376] pid_max: default: 32768 minimum: 301 <6>[ 0.029340] LSM: initializing lsm=capability <6>[ 0.033999] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041748] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.066168] rcu: Hierarchical SRCU implementation. <6>[ 0.071281] rcu: Max phase no-delay instances is 1000. <6>[ 0.076965] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.085517] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.092377] EFI services will not be available. <6>[ 0.097316] smp: Bringing up secondary CPUs ... <6>[ 0.102444] Detected PIPT I-cache on CPU1 <6>[ 0.102486] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.102495] GICv3: CPU1: using allocated LPI pending table @0x0000002080060000 <6>[ 0.102520] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.102614] smp: Brought up 1 node, 2 CPUs <6>[ 0.132934] SMP: Total of 2 processors activated. <6>[ 0.137948] CPU: All CPU(s) started at EL2 <6>[ 0.142367] CPU features: detected: 32-bit EL0 Support <6>[ 0.147820] CPU features: detected: 32-bit EL1 Support <6>[ 0.153280] CPU features: detected: CRC32 instructions <6>[ 0.158755] alternatives: applying system-wide alternatives <6>[ 0.165486] Memory: 3938460K/4194304K available (17280K kernel code, 4898K rwdata, 11876K rodata, 10432K init, 742K bss, 218504K reserved, 32768K cma-reserved) <6>[ 0.180621] devtmpfs: initialized <6>[ 0.187880] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.198010] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.205582] 21392 pages in range for non-PLT usage <6>[ 0.205587] 512912 pages in range for PLT usage <6>[ 0.210797] pinctrl core: initialized pinctrl subsystem <6>[ 0.221661] Machine: Kontron KBox A-230-LS <6>[ 0.226062] SoC family: QorIQ LS1028A <6>[ 0.230015] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.235400] DMI not present or invalid. <6>[ 0.241300] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.248066] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.255568] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.263805] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.272092] audit: initializing netlink subsys (disabled) <5>[ 0.277934] audit: type=2000 audit(0.172:1): state=initialized audit_enabled=0 res=1 <6>[ 0.278625] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.286022] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.292398] cpuidle: using governor menu <6>[ 0.303610] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.310758] ASID allocator initialised with 65536 entries <6>[ 0.317696] Serial: AMBA PL011 UART driver <6>[ 0.334702] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.341832] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.348426] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.355542] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.362134] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.369251] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.375842] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.382958] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.390729] ACPI: Interpreter disabled. <6>[ 0.396319] iommu: Default domain type: Translated <6>[ 0.401425] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.408108] SCSI subsystem initialized <6>[ 0.412379] usbcore: registered new interface driver usbfs <6>[ 0.418205] usbcore: registered new interface driver hub <6>[ 0.423849] usbcore: registered new device driver usb <6>[ 0.429778] i2c i2c-0: IMX I2C adapter registered <6>[ 0.435131] i2c i2c-1: IMX I2C adapter registered <6>[ 0.440338] i2c i2c-2: IMX I2C adapter registered <6>[ 0.445719] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.451000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.460506] PTP clock support registered <6>[ 0.464800] EDAC MC: Ver: 3.0.0 <6>[ 0.468494] scmi_core: SCMI protocol bus registered <6>[ 0.474222] FPGA manager framework <6>[ 0.477964] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.484913] vgaarb: loaded <6>[ 0.488147] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.494708] VFS: Disk quotas dquot_6.6.0 <6>[ 0.498948] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.506297] pnp: PnP ACPI: disabled <6>[ 0.514665] NET: Registered PF_INET protocol family <6>[ 0.520037] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.529775] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.538703] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.546799] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.555139] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.563476] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.570439] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.577522] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.585106] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.591411] RPC: Registered named UNIX socket transport module. <6>[ 0.597664] RPC: Registered udp transport module. <6>[ 0.602677] RPC: Registered tcp transport module. <6>[ 0.607689] RPC: Registered tcp-with-tls transport module. <6>[ 0.613491] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.620265] PCI: CLS 0 bytes, default 64 <6>[ 0.624620] Unpacking initramfs... <6>[ 0.631062] kvm [1]: nv: 554 coarse grained trap handlers <6>[ 0.637102] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.642985] kvm [1]: GICv3: no GICV resource entry <6>[ 0.648102] kvm [1]: disabling GICv2 emulation <6>[ 0.652886] kvm [1]: GIC system register CPU interface enabled <6>[ 0.659071] kvm [1]: vgic interrupt IRQ9 <6>[ 0.663350] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.670029] Initialise system trusted keyrings <6>[ 0.674971] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.681970] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.692430] NFS: Registering the id_resolver key type <5>[ 0.697846] Key type id_resolver registered <5>[ 0.702342] Key type id_legacy registered <6>[ 0.706701] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.713746] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.721618] 9p: Installing v9fs 9p2000 file system support <5>[ 0.756448] Key type asymmetric registered <5>[ 0.760860] Asymmetric key parser 'x509' registered <6>[ 0.766110] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.773851] io scheduler mq-deadline registered <6>[ 0.778693] io scheduler kyber registered <6>[ 0.783055] io scheduler bfq registered <6>[ 0.794151] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.801023] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.809153] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.818313] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.827468] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.836621] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.845774] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.854929] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.864080] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.873290] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.882547] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.889867] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.895425] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.902823] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.910656] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.918045] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.925869] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.933265] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.941088] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.948510] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 0.958218] pci 0000:00:00.0: BAR 0 [mem 0x1f8000000-0x1f803ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 0.968857] pci 0000:00:00.0: BAR 2 [mem 0x1f8160000-0x1f816ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 0.979946] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81d0000-0x1f81dffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 0.990855] pci 0000:00:00.0: VF BAR 4 [mem 0x1f81f0000-0x1f81fffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 1.002218] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.008039] pci 0000:00:00.0: VF BAR 0 [mem 0x1f81d0000-0x1f81effff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.017534] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81f0000-0x1f820ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.027690] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.037397] pci 0000:00:00.1: BAR 0 [mem 0x1f8040000-0x1f807ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.048036] pci 0000:00:00.1: BAR 2 [mem 0x1f8170000-0x1f817ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.059108] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8210000-0x1f821ffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 1.070013] pci 0000:00:00.1: VF BAR 4 [mem 0x1f8230000-0x1f823ffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 1.081367] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.087182] pci 0000:00:00.1: VF BAR 0 [mem 0x1f8210000-0x1f822ffff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.096678] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8230000-0x1f824ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.106842] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.116545] pci 0000:00:00.2: BAR 0 [mem 0x1f8080000-0x1f80bffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.127182] pci 0000:00:00.2: BAR 2 [mem 0x1f8180000-0x1f818ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.138282] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.144326] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.154033] pci 0000:00:00.3: BAR 0 [mem 0x1f8100000-0x1f811ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.164673] pci 0000:00:00.3: BAR 2 [mem 0x1f8190000-0x1f819ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.175760] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.181769] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.191475] pci 0000:00:00.4: BAR 0 [mem 0x1f8120000-0x1f813ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.202121] pci 0000:00:00.4: BAR 2 [mem 0x1f81a0000-0x1f81affff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.213209] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.219245] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 PCIe Root Complex Integrated Endpoint <6>[ 1.228946] pci 0000:00:00.5: BAR 0 [mem 0x1f8140000-0x1f815ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.239587] pci 0000:00:00.5: BAR 2 [mem 0x1f81b0000-0x1f81bffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.250662] pci 0000:00:00.5: BAR 4 [mem 0x1fc000000-0x1fc3fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.261320] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.267368] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.277090] pci 0000:00:00.6: BAR 0 [mem 0x1f80c0000-0x1f80fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.287749] pci 0000:00:00.6: BAR 2 [mem 0x1f81c0000-0x1f81cffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.298858] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.305608] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 PCIe Root Complex Event Collector <6>[ 1.315005] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.323016] pci_bus 0000:00: resource 4 [mem 0x1f8000000-0x1f815ffff] <6>[ 1.329813] pci_bus 0000:00: resource 5 [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.337041] pci_bus 0000:00: resource 6 [mem 0x1f81d0000-0x1f81effff] <6>[ 1.343816] pci_bus 0000:00: resource 7 [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.351027] pci_bus 0000:00: resource 8 [mem 0x1f8210000-0x1f822ffff] <6>[ 1.357800] pci_bus 0000:00: resource 9 [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.365008] pci_bus 0000:00: resource 10 [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.371946] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.380127] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.388196] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.394838] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.402527] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.411422] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.420369] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 1.518639] Freeing initrd memory: 25448K <6>[ 2.388157] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.394601] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.401638] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.407443] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.413949] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.424865] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 2.432529] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.438120] pci 0001:00:00.0: supports D1 D2 <6>[ 2.442696] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.449957] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.455509] pci_bus 0001:00: resource 4 [io 0x0000-0xffff] <6>[ 2.461401] pci_bus 0001:00: resource 5 [mem 0x8040000000-0x807fffffff] <6>[ 2.468485] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.476164] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.485054] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.493973] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.460156] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.466553] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.473592] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.479398] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.488712] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.499620] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 3.507284] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.512868] pci 0002:00:00.0: supports D1 D2 <6>[ 3.517444] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.524616] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.530165] pci_bus 0002:00: resource 4 [io 0x10000-0x1ffff] <6>[ 3.536232] pci_bus 0002:00: resource 5 [mem 0x8840000000-0x887fffffff] <6>[ 3.561652] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.570076] printk: legacy console [ttyS0] disabled <6>[ 3.575449] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.584617] printk: legacy console [ttyS0] enabled <6>[ 3.584617] printk: legacy console [ttyS0] enabled <6>[ 3.594791] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.594791] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.608715] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.618640] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.628646] msm_serial: driver initialized <6>[ 3.633228] SuperH (H)SCI(F) driver initialized <6>[ 3.638139] STM32 USART driver initialized <5>[ 3.645922] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.652689] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.657588] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.663187] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.668786] arm-smmu 5000000.iommu: nested translation <5>[ 3.674292] arm-smmu 5000000.iommu: coherent table walk <5>[ 3.679890] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 3.687496] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.694928] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.701761] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.708494] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.715223] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 3.722171] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 3.728348] arm-smmu 5000000.iommu: Failed to disable prefetcher for errata workarounds, check SACR.CACHE_LOCK <6>[ 3.741977] loop: module loaded <6>[ 3.753547] megasas: 07.727.03.00-rc1 <6>[ 3.758309] ahci-qoriq 3200000.sata: Adding to iommu group 0 <4>[ 3.764373] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator <4>[ 3.772225] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator <4>[ 3.779950] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator <6>[ 3.788015] ahci-qoriq 3200000.sata: AHCI vers 0001.0301, 32 command slots, 6 Gbps, platform mode <6>[ 3.797196] ahci-qoriq 3200000.sata: 1/1 ports implemented (port mask 0x1) <6>[ 3.804367] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst <6>[ 3.814793] scsi host0: ahci-qoriq <6>[ 3.818599] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 95 lpm-pol 0 <5>[ 3.845677] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 3.852776] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 3.858308] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 3.864035] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 3.871064] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 3.878236] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 3.884470] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 3.894546] tun: Universal TUN/TAP device driver, 1.6 <6>[ 3.900548] thunder_xcv, ver 1.0 <6>[ 3.904066] thunder_bgx, ver 1.0 <6>[ 3.907591] nicpf, ver 1.0 <6>[ 3.911363] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 1 <6>[ 4.020161] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.060670] mdio_bus 0000:00:00.3:04: Fixed dependency cycle(s) with /soc/pcie@1f0000000/mdio@0,3/ethernet-phy@4/vddio-regulator <6>[ 4.138444] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.199615] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 2 <6>[ 4.205948] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.212900] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.221942] pps pps0: new PPS source ptp0 <6>[ 4.226734] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.234260] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.239920] hclge is initializing <6>[ 4.243532] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.248697] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.254749] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.259996] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.266227] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.271908] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.277781] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.284339] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.290775] sky2: driver version 1.30 <6>[ 4.295656] VFIO - User Level meta-driver version: 0.3 <6>[ 4.301413] dwc3 3100000.usb: Adding to iommu group 3 <6>[ 4.307706] dwc3 3110000.usb: Adding to iommu group 4 <6>[ 4.315402] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.321196] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.329267] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.338986] xhci-hcd xhci-hcd.0.auto: irq 100, io mem 0x03110000 <6>[ 4.345370] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.351144] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.359100] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.366293] hub 1-0:1.0: USB hub found <6>[ 4.370340] hub 1-0:1.0: 1 port detected <6>[ 4.374734] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.383403] hub 2-0:1.0: USB hub found <6>[ 4.387450] hub 2-0:1.0: 1 port detected <6>[ 4.392172] usbcore: registered new interface driver usb-storage <6>[ 4.400550] i2c_dev: i2c /dev entries driver <6>[ 4.408647] sp805-wdt c000000.watchdog: registration successful <6>[ 4.415013] sp805-wdt c010000.watchdog: registration successful <6>[ 4.423183] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.432121] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.438601] sdhci: Copyright(c) Pierre Ossman <6>[ 4.443733] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.450662] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.457194] sdhci-esdhc 2140000.mmc: Adding to iommu group 5 <6>[ 4.458918] usbcore: registered new interface driver usbhid <6>[ 4.463486] sdhci-esdhc 2150000.mmc: Adding to iommu group 6 <6>[ 4.469007] usbhid: USB HID core driver <6>[ 4.479803] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 (0,8000003f) counters available <6>[ 4.497170] NET: Registered PF_PACKET protocol family <6>[ 4.507278] 9pnet: Installing 9P2000 support <5>[ 4.511946] Key type dns_resolver registered <6>[ 4.516540] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.522785] registered taskstats version 1 <6>[ 4.523749] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <5>[ 4.528152] Loading compiled-in X.509 certificates <6>[ 4.545083] Demotion targets for Node 0: null <6>[ 4.552607] fsl-edma 22c0000.dma-controller: Adding to iommu group 7 <6>[ 4.561595] pcieport 0001:00:00.0: Adding to iommu group 8 <6>[ 4.567582] pcieport 0001:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.573886] pcieport 0001:00:00.0: AER: enabled with IRQ 105 <6>[ 4.580013] pcieport 0002:00:00.0: Adding to iommu group 9 <6>[ 4.585951] pcieport 0002:00:00.0: PME: Signaling with IRQ 106 <6>[ 4.592252] pcieport 0002:00:00.0: AER: enabled with IRQ 106 <6>[ 4.603168] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.624262] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.645299] mmc0: new HS400 MMC card at address 0001 <6>[ 4.650969] mmcblk0: mmc0:0001 S0J58X 29.6 GiB <6>[ 4.656871] mmcblk0: p1 p2 p3 <6>[ 4.660707] mmcblk0boot0: mmc0:0001 S0J58X 31.5 MiB <6>[ 4.666888] mmcblk0boot1: mmc0:0001 S0J58X 31.5 MiB <6>[ 4.672945] mmcblk0rpmb: mmc0:0001 S0J58X 4.00 MiB, chardev (234:0) <6>[ 4.814343] hub 1-1:1.0: USB hub found <6>[ 4.818586] hub 1-1:1.0: 7 ports detected <6>[ 5.156244] usb 1-1.6: new full-speed USB device number 3 using xhci-hcd <3>[ 5.329396] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <6>[ 16.876335] clk: Disabling unused clocks <6>[ 16.880704] PM: genpd: Disabling unused power domains <6>[ 16.886098] ALSA device list: <6>[ 16.889384] No soundcards found. <6>[ 16.902448] Freeing unused kernel memory: 10432K <6>[ 16.907583] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.976559] udevd[112]: starting version 3.2.9 <5>[ 18.132165] random: crng init done <27>[ 18.138924] udevd[112]: specified user 'tss' unknown <27>[ 18.144333] udevd[112]: specified group 'tss' unknown <30>[ 18.150671] udevd[113]: starting eudev-3.2.9 <6>[ 18.393782] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 18.405553] fsl_ddr_edac acquired irq 109 for MC <6>[ 18.419304] fsl_ddr_edac MC err registered <6>[ 18.462798] NET: Registered PF_INET6 protocol family <4>[ 18.494771] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 18.513448] Segment Routing with IPv6 <4>[ 18.516653] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 18.517426] In-situ OAM (IOAM) with IPv6 <6>[ 18.532777] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 18.541078] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 18.556743] mscc_felix 0000:00:00.5: Adding to iommu group 10 <6>[ 18.557138] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 18.563007] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <4>[ 18.578638] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 18.582511] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 18.593178] rtc-rv8803 0-0032: registered as rtc0 <6>[ 18.598511] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.608330] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 18.622622] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.630185] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 18.645724] CAN device driver interface <6>[ 18.650163] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <3>[ 18.662861] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 18.729680] input: buttons1 as /devices/platform/buttons1/input/input13 <6>[ 18.766540] ftm-alarm 2800000.rtc: registered as rtc1 <6>[ 18.782853] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 18.791060] usbcore: registered new device driver onboard-usb-dev <6>[ 18.800190] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 18.831944] mali-dp f080000.display: Adding to iommu group 11 <6>[ 18.840770] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 18.849515] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 18.904676] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <6>[ 18.923909] caam_jr 8010000.jr: Adding to iommu group 12 <6>[ 18.944241] caam algorithms registered in /proc/crypto <6>[ 18.949740] caam 8000000.crypto: registering rng-caam <6>[ 18.955957] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 18.963176] caam_jr 8020000.jr: Adding to iommu group 13 <6>[ 18.972368] caam_jr 8030000.jr: Adding to iommu group 14 <6>[ 18.980478] caam_jr 8040000.jr: Adding to iommu group 15 done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-511365/environment . /lava-511365/environment / # /lava-511365/bin/lava-test-runner /lava-511365/0 /lava-511365/bin/lava-test-runner /lava-511365/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 19.573198] d /lava-511365/0/tests/0_dmesg + cat uuid + UUID=511365_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.593777] <8>[ 19.614904] <8>[ 19.636603] + set +x <8>[ 19.646342] / #