connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='default', state=, avail=True, host='nuc-1', port=39083, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:39083 connected to 192.168.0.1 (port 39083) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.212 (8 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3907102/tftp-deploy-ibtywh3u/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3907102/tftp-deploy-ibtywh3u/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 2.1 MiB/s done Bytes transferred = 10789376 (a4a200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3907102/tftp-deploy-ibtywh3u/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3907102/tftp-deploy-ibtywh3u/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 2.6 MiB/s done Bytes transferred = 17516883 (10b4953 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3907102/tftp-deploy-ibtywh3u/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3907102/tftp-deploy-ibtywh3u/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *###### 2.9 MiB/s done Bytes transferred = 73434 (11eda hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0xa4a200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17516819 Bytes = 16.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f94ed9 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j365407-arm-gcc-12-multi-v7-defconfig-config-thumb2-4zgdt) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Wed Nov 6 19:19:29 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: legacy bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40844 r8192 d20596 u69632 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524032 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.000001] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.008576] Switching to timer-based delay loop, resolution 83ns <6>[ 0.015624] Console: colour dummy device 80x30 <6>[ 0.020557] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.031576] CPU: Testing write buffer coherency: ok <6>[ 0.036947] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.042558] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.049414] pid_max: default: 32768 minimum: 301 <6>[ 0.054635] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.062491] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <3>[ 0.071613] /cpus/cpu@0 missing clock-frequency property <3>[ 0.077433] /cpus/cpu@1 missing clock-frequency property <3>[ 0.083272] /cpus/cpu@2 missing clock-frequency property <3>[ 0.089089] /cpus/cpu@3 missing clock-frequency property <6>[ 0.094892] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.102035] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.111298] rcu: Hierarchical SRCU implementation. <6>[ 0.116540] rcu: Max phase no-delay instances is 1000. <6>[ 0.122544] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.133504] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.142469] EFI services will not be available. <6>[ 0.147740] smp: Bringing up secondary CPUs ... <6>[ 0.153434] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.153453] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.170545] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.170564] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.187668] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.187687] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.204067] smp: Brought up 1 node, 4 CPUs <6>[ 0.208610] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.215293] CPU: All CPU(s) started in SVC mode. <6>[ 0.221005] Memory: 1967968K/2096128K available (11264K kernel code, 2543K rwdata, 6788K rodata, 2048K init, 430K bss, 59368K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.237872] devtmpfs: initialized <6>[ 0.259155] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.267633] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.278120] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.286994] pinctrl core: initialized pinctrl subsystem <6>[ 0.296477] DMI not present or invalid. <6>[ 0.301482] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.310144] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.321262] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.321323] cpuidle: using governor menu <6>[ 0.344947] platform 70000868.pinmux: Fixed dependency cycle(s) with /pinmux@70000868/pinmux <6>[ 0.379454] No ATAGs? <6>[ 0.382227] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.390824] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.413348] Serial: AMBA PL011 UART driver <3>[ 0.419237] tegra-mc 70019000.memory-controller: ppcsahbslvr: secure read @0x7fd41100: EMEM address decode error (EMEM decode error) <6>[ 0.450625] iommu: Default domain type: Translated <6>[ 0.455907] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.464071] SCSI subsystem initialized <6>[ 0.468736] usbcore: registered new interface driver usbfs <6>[ 0.474750] usbcore: registered new interface driver hub <6>[ 0.480603] usbcore: registered new device driver usb <6>[ 0.487813] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.493252] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.503030] PTP clock support registered <6>[ 0.507577] EDAC MC: Ver: 3.0.0 <6>[ 0.511485] scmi_core: SCMI protocol bus registered <6>[ 0.519289] vgaarb: loaded <6>[ 0.528345] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.547098] NET: Registered PF_INET protocol family <6>[ 0.552651] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.562134] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.571120] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.579445] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.587835] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.595940] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.602890] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.610084] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.617828] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.624583] RPC: Registered named UNIX socket transport module. <6>[ 0.631026] RPC: Registered udp transport module. <6>[ 0.636177] RPC: Registered tcp transport module. <6>[ 0.641345] RPC: Registered tcp-with-tls transport module. <6>[ 0.647304] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.654279] PCI: CLS 0 bytes, default 64 <5>[ 0.659997] Initialise system trusted keyrings <6>[ 0.665141] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.665509] Trying to unpack rootfs image as initramfs... <6>[ 0.672650] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.684663] NFS: Registering the id_resolver key type <5>[ 0.690249] Key type id_resolver registered <5>[ 0.694871] Key type id_legacy registered <6>[ 0.699358] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.706603] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.714941] Key type asymmetric registered <5>[ 0.719521] Asymmetric key parser 'x509' registered <6>[ 0.724949] bounce: pool size: 64 pages <6>[ 0.729269] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.737236] io scheduler mq-deadline registered <6>[ 0.742245] io scheduler kyber registered <6>[ 0.746717] io scheduler bfq registered <4>[ 0.774334] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.800891] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.829862] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 0.842866] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 0.924181] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.936661] printk: legacy console [ttyS0] disabled <6>[ 0.942476] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 70, base_baud = 25500000) is a Tegra <6>[ 0.952038] printk: legacy console [ttyS0] enabled <6>[ 0.952038] printk: legacy console [ttyS0] enabled <6>[ 0.962323] printk: legacy bootconsole [uart0] disabled <6>[ 0.962323] printk: legacy bootconsole [uart0] disabled <6>[ 0.975480] msm_serial: driver initialized <6>[ 0.980366] SuperH (H)SCI(F) driver initialized <6>[ 0.985506] STMicroelectronics ASC driver initialized <6>[ 0.990997] STM32 USART driver initialized <6>[ 0.996502] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 71, base_baud = 0) is a TEGRA_UART <6>[ 1.006536] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 72, base_baud = 0) is a TEGRA_UART <6>[ 1.019963] tegra-host1x 50000000.host1x: Adding to iommu group 0 <6>[ 1.036542] tegra-vic 54340000.vic: Adding to iommu group 1 <6>[ 1.055563] brd: module loaded <6>[ 1.065864] loop: module loaded <3>[ 1.121461] spi spi1.0: Invalid delay unit 2, should be SPI_DELAY_UNIT_SCK <3>[ 1.128628] spi-tegra114 7000da00.spi: can't setup spi1.0, status -22 <3>[ 1.135330] spi_master spi1: spi_device register error /spi@7000da00/flash@0 <4>[ 1.142694] spi_master spi1: Failed to create SPI device for /spi@7000da00/flash@0 <6>[ 1.156940] CAN device driver interface <6>[ 1.162389] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.169799] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.175022] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.181261] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.186917] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.198471] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.204342] usbcore: registered new interface driver pegasus <6>[ 1.210318] usbcore: registered new interface driver asix <6>[ 1.216010] usbcore: registered new interface driver ax88179_178a <6>[ 1.222414] usbcore: registered new interface driver cdc_ether <6>[ 1.228556] usbcore: registered new interface driver smsc75xx <6>[ 1.234598] usbcore: registered new interface driver smsc95xx <6>[ 1.240671] usbcore: registered new interface driver net1080 <6>[ 1.246623] usbcore: registered new interface driver cdc_subset <6>[ 1.252858] usbcore: registered new interface driver zaurus <6>[ 1.258740] usbcore: registered new interface driver cdc_ncm <4>[ 1.265216] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 1.273693] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 1.286952] usbcore: registered new interface driver usb-storage <6>[ 1.355759] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 1.360947] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 1.418364] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.10 <6>[ 1.424961] hub 1-0:1.0: USB hub found <6>[ 1.429044] hub 1-0:1.0: 1 port detected <6>[ 1.439340] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 1.444748] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 1.451940] i2c_dev: i2c /dev entries driver <4>[ 1.470219] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 1.477961] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 1.530163] i2c 4-0040: Fixed dependency cycle(s) with /i2c@7000d000/pmic@40/pinmux <6>[ 1.539151] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 1.555566] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 1.561675] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:18 UTC (946684818) <6>[ 1.570579] as3722-rtc as3722-rtc: RTC interrupt 101 <6>[ 1.577976] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <4>[ 1.596251] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 1.605813] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 1.612814] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 1.619893] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 1.637990] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.644460] sdhci: Copyright(c) Pierre Ossman <6>[ 1.651482] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.659918] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.668920] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 1.671714] usbcore: registered new interface driver usbhid <6>[ 1.673946] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 1.679735] usbhid: USB HID core driver <6>[ 1.685595] tegra-emc 7001b000.external-memory-controller: 64bit DRAM bus <6>[ 1.698082] tegra-emc 7001b000.external-memory-controller: OPP HW ver. 0x2, current clock rate 924 MHz <4>[ 1.710377] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 1.718597] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 1.722465] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 (8000003f) counters available <6>[ 1.738465] NET: Registered PF_INET6 protocol family <6>[ 1.744789] Segment Routing with IPv6 <6>[ 1.748841] In-situ OAM (IOAM) with IPv6 <6>[ 1.753104] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.760012] NET: Registered PF_PACKET protocol family <6>[ 1.765326] can: controller area network core <6>[ 1.770021] NET: Registered PF_CAN protocol family <6>[ 1.775076] can: raw protocol <6>[ 1.778307] can: broadcast manager protocol <6>[ 1.782793] can: netlink gateway - max_hops=1 <5>[ 1.787802] Key type dns_resolver registered <6>[ 1.793960] ThumbEE CPU extension supported. <5>[ 1.798532] Registering SWP/SWPB emulation handler <5>[ 1.816728] Loading compiled-in X.509 certificates <6>[ 1.830391] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 1.873915] reg-fixed-voltage regulator-12v0sata: nonexclusive access to GPIO for (default) <6>[ 1.884256] tegra-dc 54200000.dc: Adding to iommu group 1 <4>[ 1.890013] Failed to attached device 54200000.dc to IOMMU_mapping <6>[ 1.897963] tegra-dc 54240000.dc: Adding to iommu group 1 <4>[ 1.903705] Failed to attached device 54240000.dc to IOMMU_mapping <6>[ 1.917166] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <3>[ 1.926739] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 1.932719] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 1.935488] ci_hdrc ci_hdrc.2: EHCI Host Controller <4>[ 1.944449] ------------[ cut here ]------------ <6>[ 1.945558] ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2 <4>[ 1.950409] WARNING: CPU: 1 PID: 55 at drivers/regulator/core.c:5885 regulator_unregister+0xf1/0xfc <4>[ 1.967043] Modules linked in: <4>[ 1.970421] CPU: 1 UID: 0 PID: 55 Comm: kworker/u17:3 Not tainted 6.12.0-rc6 #1 <4>[ 1.978005] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) <4>[ 1.984534] Workqueue: async async_run_entry_fn <4>[ 1.989348] Call trace: <4>[ 1.989361] unwind_backtrace from show_stack+0xb/0xc <4>[ 1.997481] show_stack from dump_stack_lvl+0x45/0x4e <4>[ 2.002811] dump_stack_lvl from __warn+0xe3/0xf0 <4>[ 2.007797] __warn from warn_slowpath_fmt+0x10d/0x114 <4>[ 2.013214] warn_slowpath_fmt from regulator_unregister+0xf1/0xfc <4>[ 2.019679] regulator_unregister from release_nodes+0x2f/0x7c <4>[ 2.025791] release_nodes from devres_release_all+0x59/0x90 <4>[ 2.031731] devres_release_all from device_unbind_cleanup+0x9/0x3c <6>[ 2.037919] Freeing initrd memory: 17108K <4>[ 2.038281] device_unbind_cleanup from really_probe+0x103/0x1c0 <4>[ 2.048801] really_probe from __driver_probe_device+0x59/0x12c <4>[ 2.054997] __driver_probe_device from driver_probe_device+0x2d/0xc8 <4>[ 2.061712] driver_probe_device from __device_attach_driver+0x4f/0xa0 <4>[ 2.068516] __device_attach_driver from bus_for_each_drv+0x59/0x94 <4>[ 2.075055] bus_for_each_drv from __device_attach_async_helper+0x73/0x8c <4>[ 2.082124] __device_attach_async_helper from async_run_entry_fn+0x1b/0x84 <4>[ 2.089389] async_run_entry_fn from process_one_work+0x113/0x2ac <4>[ 2.095784] process_one_work from worker_thread+0x1f3/0x2e0 <4>[ 2.101742] worker_thread from kthread+0xb9/0xcc <4>[ 2.106749] kthread from ret_from_fork+0x11/0x1c <4>[ 2.111737] Exception stack(0xf093dfb0 to 0xf093dff8) <4>[ 2.117057] dfa0: 00000000 00000000 00000000 00000000 <4>[ 2.125501] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <4>[ 2.133950] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 <4>[ 2.140925] ---[ end trace 0000000000000000 ]--- <3>[ 2.146197] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3run <6>[ 2.178480] ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.10 <6>[ 2.185344] hub 2-0:1.0: USB hub found <6>[ 2.185364] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 2.189508] hub 2-0:1.0: 1 port detected <6>[ 2.203863] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 2.221389] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.222730] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.226418] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 2.233250] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.246564] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.255010] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.263443] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.272052] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.282235] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <4>[ 2.282906] as3722-regulator as3722-regulator: DMA mask not set <6>[ 2.289070] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <3>[ 2.296756] debugfs: Directory '+VDD_CPU_AP' with parent 'regulator' already present! <6>[ 2.303597] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <3>[ 2.316723] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 2.320073] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.326369] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 2.334319] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.341522] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 2.349410] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.356366] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <3>[ 2.361842] tegra-pcie 1003000.pcie: failed to get PHY#0: -517 <6>[ 2.368355] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <3>[ 2.373893] tegra-pcie 1003000.pcie: failed to get PHYs: -517 <3>[ 2.386409] tegra-pcie 1003000.pcie: failed to request resources: -517 <6>[ 2.396283] sdhci-tegra 700b0400.mmc: Got CD GPIO <4>[ 2.399357] usb2-0: supply vbus not found, using dummy regulator <6>[ 2.401331] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 2.407719] usb2-1: supply vbus not found, using dummy regulator <6>[ 2.418302] mmc1: new high speed MMC card at address 0001 <6>[ 2.420391] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.431429] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.431889] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <4>[ 2.431910] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 2.439824] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.447988] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 2.450818] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.459900] mmcblk1boot0: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.463754] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.472938] mmcblk1boot1: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.477332] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.486428] mmcblk1rpmb: mmc1:0001 SEM16G 4.00 MiB, chardev (236:0) <6>[ 2.492379] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 2.511595] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 2.523538] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 2.983313] mmc0: new high speed SD card at address 0260 <6>[ 2.990173] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 2.997406] mmcblk0: p1 p2 <6>[ 3.730452] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 3.740723] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 3.747250] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 3.753012] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 3.760162] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 3.766597] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 3.773739] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 3.781643] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 PCIe Root Port <4>[ 3.789225] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 3.799168] pci 0000:00:02.0: PCI bridge to [bus 00] <6>[ 3.804395] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff] <6>[ 3.810776] pci 0000:00:02.0: enabling Extended Tags <6>[ 3.816060] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.826585] PCI: bus0: Fast back to back transfers disabled <6>[ 3.832433] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 3.840859] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint <6>[ 3.848384] pci 0000:01:00.0: BAR 0 [io 0x0000-0x00ff] <6>[ 3.853898] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00000fff 64bit] <6>[ 3.860628] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00003fff 64bit pref] <6>[ 3.867931] pci 0000:01:00.0: supports D1 D2 <6>[ 3.872472] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.898421] PCI: bus1: Fast back to back transfers disabled <6>[ 3.904251] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.911168] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]: assigned <6>[ 3.918925] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref]: assigned <6>[ 3.927620] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]: assigned <6>[ 3.934685] pci 0000:01:00.0: BAR 4 [mem 0x20000000-0x20003fff 64bit pref]: assigned <6>[ 3.942718] pci 0000:01:00.0: BAR 2 [mem 0x13000000-0x13000fff 64bit]: assigned <6>[ 3.950309] pci 0000:01:00.0: BAR 0 [io 0x1000-0x10ff]: assigned <6>[ 3.956665] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 3.961899] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 3.968250] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 3.975305] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <6>[ 3.983319] pci_bus 0000:00: resource 4 [mem 0x01000000-0x01001fff] <6>[ 3.989856] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] <6>[ 3.995683] pci_bus 0000:00: resource 6 [mem 0x13000000-0x1fffffff] <6>[ 4.002218] pci_bus 0000:00: resource 7 [mem 0x20000000-0x3fffffff pref] <6>[ 4.009185] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] <6>[ 4.015012] pci_bus 0000:01: resource 1 [mem 0x13000000-0x130fffff] <6>[ 4.021545] pci_bus 0000:01: resource 2 [mem 0x20000000-0x200fffff 64bit pref] <4>[ 4.029058] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 4.036368] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 4.042849] pcieport 0000:00:02.0: PME: Signaling with IRQ 127 <6>[ 4.049276] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 4.104577] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 130 <6>[ 4.112970] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <4>[ 4.122608] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 4.130519] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 4.138426] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 4.147139] tegra-ahci 70027000.sata: AHCI vers 0001.0301, 32 command slots, 3 Gbps, platform mode <6>[ 4.156358] tegra-ahci 70027000.sata: 1/2 ports implemented (port mask 0x1) <6>[ 4.163596] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 4.173635] scsi host0: tegra-ahci <6>[ 4.177608] scsi host1: tegra-ahci <6>[ 4.181353] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 131 lpm-pol 0 <6>[ 4.190498] ata2: DUMMY <6>[ 4.193682] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.511277] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 4.521064] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 4.530528] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 4.568603] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC) <6>[ 4.708976] r8169 0000:01:00.0 eth0: Link is Down <6>[ 6.279280] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <5>[ 6.308379] Sending DHCP requests ., OK <6>[ 6.354784] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.212 <6>[ 6.363017] IP-Config: Complete: <6>[ 6.366546] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.212, mask=255.255.255.0, gw=192.168.0.254 <6>[ 6.377319] host=192.168.0.212, domain=shed, nis-domain=(none) <6>[ 6.383944] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 6.383987] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 6.398514] clk: Disabling unused clocks <6>[ 6.403451] PM: genpd: Disabling unused power domains <6>[ 6.411634] Freeing unused kernel image (initmem) memory: 2048K <6>[ 6.417973] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.484438] udevd[144]: starting version 3.2.9 <5>[ 14.178343] random: crng init done <27>[ 14.184716] udevd[144]: specified user 'tss' unknown <27>[ 14.190150] udevd[144]: specified group 'tss' unknown <30>[ 14.196490] udevd[145]: starting eudev-3.2.9 <6>[ 14.337009] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 14.359030] r8169 0000:01:00.0 enp1s0: renamed from eth0 (while UP) <4>[ 14.370168] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 14.380176] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 14.386694] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 14.393311] tegra-xusb 70090000.usb: probe with driver tegra-xusb failed with error -2 <6>[ 14.403684] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 101000 mC <6>[ 14.413440] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 101000 mC <6>[ 14.429374] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 101000 mC <6>[ 14.439133] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 101000 mC <6>[ 14.452882] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC <6>[ 14.463013] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 101000 mC <6>[ 14.499139] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 14.575055] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub done Saving random seed: <6>[ 14.884002] input: NVIDIA Tegra Jetson TK1 Headphones Jack as /devices/soc0/sound/sound/card1/input2 OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3907102/environment / # /lava-3907102/bin/lava-test-runner /lava-3907102/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3907102/0/tests/0_dmesg + cat uuid + UUID=3<8>[ 15.543433] 907102_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.575844] <8>[ 15.604144] <8>[ 15.631167] + set +x <8>[ 15.640877] / #