Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.112 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 512098/tftp-deploy-f23dd51v/kernel/Image tftp 0x82000000 512098/tftp-deploy-f23dd51v/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.112; sending through gateway 172.16.0.254 Filename '512098/tftp-deploy-f23dd51v/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################### 15.1 MiB/s done Bytes transferred = 39424512 (2599200 hex) => tftp 0x90080000 512098/tftp-deploy-f23dd51v/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 512098/tftp-deploy-f23dd51v/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.112; sending through gateway 172.16.0.254 Filename '512098/tftp-deploy-f23dd51v/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 14.9 MiB/s done Bytes transferred = 26768777 (1987589 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 512098/tftp-deploy-f23dd51v/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 512098/tftp-deploy-f23dd51v/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.112; sending through gateway 172.16.0.254 Filename '512098/tftp-deploy-f23dd51v/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *### 5.7 MiB/s done Bytes transferred = 29929 (74e9 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-06 20:04:15 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 26768713 Bytes = 25.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a4e8 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j365443-arm64-clang-15-defconfig-config-arm64-64k-panjs6r) (Debian clang version 15.0.7, Debian LLD 15.0.7) #1 SMP PREEMPT Wed Nov 6 19:37:18 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550a0] enabled [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x20fff452c0-0x20fff47cff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 1056 pages in unavailable ranges [ 0.000000] cma: Reserved 512 MiB at 0x00000000c0000000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 2 pages/cpu s61976 r8192 d60904 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64480 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f7d30000-0x00000000fbd30000] (64MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080180000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080160000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080170000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008878] Console: colour dummy device 80x25 <6>[ 0.013714] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024435] pid_max: default: 32768 minimum: 301 <6>[ 0.029400] LSM: initializing lsm=capability <6>[ 0.034063] Mount-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) <6>[ 0.041810] Mountpoint-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) <6>[ 0.062268] rcu: Hierarchical SRCU implementation. <6>[ 0.067380] rcu: Max phase no-delay instances is 1000. <6>[ 0.073081] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.081641] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.088563] EFI services will not be available. <6>[ 0.093548] smp: Bringing up secondary CPUs ... <6>[ 0.098690] Detected PIPT I-cache on CPU1 <6>[ 0.098733] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.098742] GICv3: CPU1: using allocated LPI pending table @0x0000002080200000 <6>[ 0.098768] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.098877] smp: Brought up 1 node, 2 CPUs <6>[ 0.129195] SMP: Total of 2 processors activated. <6>[ 0.134207] CPU: All CPU(s) started at EL2 <6>[ 0.138626] CPU features: detected: 32-bit EL0 Support <6>[ 0.144078] CPU features: detected: 32-bit EL1 Support <6>[ 0.149537] CPU features: detected: CRC32 instructions <6>[ 0.155011] alternatives: applying system-wide alternatives <6>[ 0.161832] Memory: 3448448K/4126720K available (17664K kernel code, 5092K rwdata, 12096K rodata, 3072K init, 1181K bss, 144256K reserved, 524288K cma-reserved) <6>[ 0.177110] devtmpfs: initialized <6>[ 0.183801] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.193926] futex hash table entries: 512 (order: -1, 32768 bytes, linear) <6>[ 0.201603] 1421 pages in range for non-PLT usage <6>[ 0.201608] 32141 pages in range for PLT usage <6>[ 0.206745] pinctrl core: initialized pinctrl subsystem <6>[ 0.217520] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.225166] SoC family: QorIQ LS1028A <6>[ 0.229119] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.234486] DMI not present or invalid. <6>[ 0.239866] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.249152] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.256680] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.264877] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.273178] audit: initializing netlink subsys (disabled) <5>[ 0.279203] audit: type=2000 audit(0.168:1): state=initialized audit_enabled=0 res=1 <6>[ 0.279939] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.287300] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.293672] cpuidle: using governor menu <6>[ 0.304932] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.312081] ASID allocator initialised with 65536 entries <6>[ 0.319208] Serial: AMBA PL011 UART driver <6>[ 0.337138] HugeTLB: registered 16.0 GiB page size, pre-allocated 0 pages <6>[ 0.344268] HugeTLB: 0 KiB vmemmap can be freed for a 16.0 GiB page <6>[ 0.350863] HugeTLB: registered 512 MiB page size, pre-allocated 0 pages <6>[ 0.357893] HugeTLB: 0 KiB vmemmap can be freed for a 512 MiB page <6>[ 0.364396] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.371512] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.379463] ACPI: Interpreter disabled. <6>[ 0.385450] iommu: Default domain type: Translated <6>[ 0.390559] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.397230] SCSI subsystem initialized <6>[ 0.401497] usbcore: registered new interface driver usbfs <6>[ 0.407319] usbcore: registered new interface driver hub <6>[ 0.412960] usbcore: registered new device driver usb <6>[ 0.418893] i2c i2c-0: IMX I2C adapter registered <6>[ 0.424150] i2c i2c-1: IMX I2C adapter registered <6>[ 0.429565] i2c i2c-2: IMX I2C adapter registered <6>[ 0.435108] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.440400] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.449924] PTP clock support registered <6>[ 0.454226] EDAC MC: Ver: 3.0.0 <6>[ 0.457944] scmi_core: SCMI protocol bus registered <6>[ 0.463706] FPGA manager framework <6>[ 0.467457] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.474449] vgaarb: loaded <6>[ 0.477705] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.484403] VFS: Disk quotas dquot_6.6.0 <6>[ 0.488658] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes) <6>[ 0.496202] pnp: PnP ACPI: disabled <6>[ 0.504379] NET: Registered PF_INET protocol family <6>[ 0.509752] IP idents hash table entries: 65536 (order: 3, 524288 bytes, linear) <6>[ 0.519412] tcp_listen_portaddr_hash hash table entries: 4096 (order: 0, 65536 bytes, linear) <6>[ 0.528361] Table-perturb hash table entries: 65536 (order: 2, 262144 bytes, linear) <6>[ 0.536454] TCP established hash table entries: 32768 (order: 2, 262144 bytes, linear) <6>[ 0.544796] TCP bind hash table entries: 32768 (order: 4, 1048576 bytes, linear) <6>[ 0.553149] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.560095] UDP hash table entries: 2048 (order: 0, 65536 bytes, linear) <6>[ 0.567164] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes, linear) <6>[ 0.574749] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.581037] RPC: Registered named UNIX socket transport module. <6>[ 0.587288] RPC: Registered udp transport module. <6>[ 0.592300] RPC: Registered tcp transport module. <6>[ 0.597310] RPC: Registered tcp-with-tls transport module. <6>[ 0.603111] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.609884] PCI: CLS 0 bytes, default 64 <6>[ 0.614235] Unpacking initramfs... <6>[ 0.620582] kvm [1]: nv: 554 coarse grained trap handlers <6>[ 0.626606] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.631425] kvm [1]: GICv3: no GICV resource entry <6>[ 0.636535] kvm [1]: disabling GICv2 emulation <6>[ 0.641313] kvm [1]: GIC system register CPU interface enabled <6>[ 0.647489] kvm [1]: vgic interrupt IRQ9 <6>[ 0.651749] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.658362] Initialise system trusted keyrings <6>[ 0.663283] workingset: timestamp_bits=42 max_order=16 bucket_order=0 <6>[ 0.670282] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.680708] NFS: Registering the id_resolver key type <5>[ 0.686130] Key type id_resolver registered <5>[ 0.690626] Key type id_legacy registered <6>[ 0.694971] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.702005] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.709909] 9p: Installing v9fs 9p2000 file system support <5>[ 0.738481] Key type asymmetric registered <5>[ 0.742892] Asymmetric key parser 'x509' registered <6>[ 0.748135] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.755873] io scheduler mq-deadline registered <6>[ 0.760712] io scheduler kyber registered <6>[ 0.765067] io scheduler bfq registered <6>[ 0.780853] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.787753] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.795890] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.805070] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.814244] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.823413] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.832581] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.841747] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.850913] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.860110] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.869356] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.876677] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.882234] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.889621] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.897447] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.904832] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.912658] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.920047] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.927879] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.935300] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 0.945006] pci 0000:00:00.0: BAR 0 [mem 0x1f8000000-0x1f803ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 0.955643] pci 0000:00:00.0: BAR 2 [mem 0x1f8160000-0x1f816ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 0.966716] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81d0000-0x1f81dffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 0.977610] pci 0000:00:00.0: VF BAR 4 [mem 0x1f81f0000-0x1f81fffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 0.988967] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.994780] pci 0000:00:00.0: VF BAR 0 [mem 0x1f81d0000-0x1f81effff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.004311] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81f0000-0x1f820ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.014473] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.024192] pci 0000:00:00.1: BAR 0 [mem 0x1f8040000-0x1f807ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.034845] pci 0000:00:00.1: BAR 2 [mem 0x1f8170000-0x1f817ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.045935] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8210000-0x1f821ffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 1.056846] pci 0000:00:00.1: VF BAR 4 [mem 0x1f8230000-0x1f823ffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 1.068212] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.074036] pci 0000:00:00.1: VF BAR 0 [mem 0x1f8210000-0x1f822ffff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.083542] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8230000-0x1f824ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.093728] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.103431] pci 0000:00:00.2: BAR 0 [mem 0x1f8080000-0x1f80bffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.114073] pci 0000:00:00.2: BAR 2 [mem 0x1f8180000-0x1f818ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.125158] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.131163] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.140866] pci 0000:00:00.3: BAR 0 [mem 0x1f8100000-0x1f811ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.151501] pci 0000:00:00.3: BAR 2 [mem 0x1f8190000-0x1f819ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.162583] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.168567] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.178275] pci 0000:00:00.4: BAR 0 [mem 0x1f8120000-0x1f813ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.188912] pci 0000:00:00.4: BAR 2 [mem 0x1f81a0000-0x1f81affff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.199998] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.206016] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 PCIe Root Complex Integrated Endpoint <6>[ 1.215734] pci 0000:00:00.5: BAR 0 [mem 0x1f8140000-0x1f815ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.226384] pci 0000:00:00.5: BAR 2 [mem 0x1f81b0000-0x1f81bffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.237478] pci 0000:00:00.5: BAR 4 [mem 0x1fc000000-0x1fc3fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.248156] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.254240] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.263961] pci 0000:00:00.6: BAR 0 [mem 0x1f80c0000-0x1f80fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.274612] pci 0000:00:00.6: BAR 2 [mem 0x1f81c0000-0x1f81cffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.285715] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.292464] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 PCIe Root Complex Event Collector <6>[ 1.301837] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.309821] pci_bus 0000:00: resource 4 [mem 0x1f8000000-0x1f815ffff] <6>[ 1.316598] pci_bus 0000:00: resource 5 [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.323806] pci_bus 0000:00: resource 6 [mem 0x1f81d0000-0x1f81effff] <6>[ 1.330575] pci_bus 0000:00: resource 7 [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.337783] pci_bus 0000:00: resource 8 [mem 0x1f8210000-0x1f822ffff] <6>[ 1.344555] pci_bus 0000:00: resource 9 [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.351763] pci_bus 0000:00: resource 10 [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.461723] pci 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 1.469462] pci 0000:00:00.1: enetc_fixup_clear_rss_rfs+0x0/0x58 took 108221 usecs <6>[ 1.546683] Freeing initrd memory: 26048K <6>[ 1.577726] pci 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 1.584342] pci 0000:00:00.2: enetc_fixup_clear_rss_rfs+0x0/0x58 took 104407 usecs <6>[ 1.693721] pci 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 1.700306] pci 0000:00:00.6: enetc_fixup_clear_rss_rfs+0x0/0x58 took 105469 usecs <6>[ 1.708252] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.716409] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.722696] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.729260] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.736957] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.745851] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.754782] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 2.721713] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.728117] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.735156] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.740961] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.747467] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.758380] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 2.766043] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.771633] pci 0001:00:00.0: supports D1 D2 <6>[ 2.776208] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.783514] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.789065] pci_bus 0001:00: resource 4 [io 0x0000-0xffff] <6>[ 2.794956] pci_bus 0001:00: resource 5 [mem 0x8040000000-0x807fffffff] <6>[ 2.801996] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.809668] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.818559] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.827475] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.793714] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.800106] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.807141] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.812946] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.822260] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.833167] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 3.840829] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.846414] pci 0002:00:00.0: supports D1 D2 <6>[ 3.850989] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.858239] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.863787] pci_bus 0002:00: resource 4 [io 0x10000-0x1ffff] <6>[ 3.869853] pci_bus 0002:00: resource 5 [mem 0x8840000000-0x887fffffff] <6>[ 3.896788] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.905240] printk: legacy console [ttyS0] disabled <6>[ 3.910613] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.919780] printk: legacy console [ttyS0] enabled <6>[ 3.919780] printk: legacy console [ttyS0] enabled <6>[ 3.929972] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.929972] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.946210] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.956141] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.966168] msm_serial: driver initialized <6>[ 3.970782] SuperH (H)SCI(F) driver initialized <6>[ 3.975713] STM32 USART driver initialized <5>[ 3.983495] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.990245] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.995144] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.000742] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.006368] arm-smmu 5000000.iommu: nested translation <5>[ 4.011879] arm-smmu 5000000.iommu: coherent table walk <5>[ 4.017480] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 4.025085] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.032517] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.039338] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.046070] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.052797] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.059750] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 4.065928] arm-smmu 5000000.iommu: Failed to disable prefetcher for errata workarounds, check SACR.CACHE_LOCK <6>[ 4.079604] loop: module loaded <6>[ 4.091710] megasas: 07.727.03.00-rc1 <5>[ 4.130360] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.137460] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.142986] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.148709] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.155724] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.162752] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.168945] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.179203] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.185215] thunder_xcv, ver 1.0 <6>[ 4.188748] thunder_bgx, ver 1.0 <6>[ 4.192272] nicpf, ver 1.0 <6>[ 4.196012] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 0 <6>[ 4.305720] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.329889] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 1 <6>[ 4.336203] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.343172] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.352200] pps pps0: new PPS source ptp0 <6>[ 4.356991] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.364515] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.370156] hclge is initializing <6>[ 4.373775] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.378936] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.384989] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.390233] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.396459] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.402141] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.408013] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.414566] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.421016] sky2: driver version 1.30 <6>[ 4.425964] VFIO - User Level meta-driver version: 0.3 <6>[ 4.431706] dwc3 3100000.usb: Adding to iommu group 2 <6>[ 4.438157] dwc3 3110000.usb: Adding to iommu group 3 <6>[ 4.446898] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.452688] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.460853] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.470565] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x03100000 <6>[ 4.476846] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.482624] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.490605] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.497904] hub 1-0:1.0: USB hub found <6>[ 4.501949] hub 1-0:1.0: 1 port detected <6>[ 4.506342] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.515014] hub 2-0:1.0: USB hub found <6>[ 4.519057] hub 2-0:1.0: 1 port detected <6>[ 4.523479] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.529280] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.537456] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.547189] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03110000 <6>[ 4.553468] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.559250] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.567207] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.574360] hub 3-0:1.0: USB hub found <6>[ 4.578416] hub 3-0:1.0: 1 port detected <6>[ 4.582807] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.591512] hub 4-0:1.0: USB hub found <6>[ 4.595556] hub 4-0:1.0: 1 port detected <6>[ 4.600294] usbcore: registered new interface driver usb-storage <6>[ 4.608811] i2c_dev: i2c /dev entries driver <6>[ 4.617114] sp805-wdt c000000.watchdog: registration successful <6>[ 4.623500] sp805-wdt c010000.watchdog: registration successful <6>[ 4.631798] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.640784] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.647267] sdhci: Copyright(c) Pierre Ossman <6>[ 4.652463] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.659451] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.666112] sdhci-esdhc 2150000.mmc: Adding to iommu group 4 <6>[ 4.667856] usbcore: registered new interface driver usbhid <6>[ 4.672245] sdhci-esdhc 2140000.mmc: Adding to iommu group 5 <6>[ 4.677927] usbhid: USB HID core driver <6>[ 4.688303] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 (0,8000003f) counters available <6>[ 4.702793] NET: Registered PF_PACKET protocol family <6>[ 4.708214] 9pnet: Installing 9P2000 support <5>[ 4.712835] Key type dns_resolver registered <6>[ 4.723942] registered taskstats version 1 <5>[ 4.728420] Loading compiled-in X.509 certificates <6>[ 4.733525] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.737725] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.747884] Demotion targets for Node 0: null <6>[ 4.755490] fsl-edma 22c0000.dma-controller: Adding to iommu group 6 <6>[ 4.763380] pcieport 0001:00:00.0: Adding to iommu group 7 <6>[ 4.769321] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.775682] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.781849] pcieport 0002:00:00.0: Adding to iommu group 8 <6>[ 4.787848] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.794134] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.802879] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.833726] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.838533] mmc0: new HS400 MMC card at address 0001 <6>[ 4.850229] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.860640] mmcblk0: p1 p2 <6>[ 4.864157] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.870284] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.876289] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 5.022475] hub 3-1:1.0: USB hub found <6>[ 5.026695] hub 3-1:1.0: 7 ports detected <6>[ 17.093881] clk: Disabling unused clocks <6>[ 17.098208] PM: genpd: Disabling unused power domains <6>[ 17.103593] ALSA device list: <6>[ 17.106876] No soundcards found. <6>[ 17.112497] Freeing unused kernel memory: 3072K <6>[ 17.117448] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 17.182669] udevd[107]: starting version 3.2.9 <5>[ 18.281721] random: crng init done <27>[ 18.288086] udevd[107]: specified user 'tss' unknown <27>[ 18.293487] udevd[107]: specified group 'tss' unknown <30>[ 18.299946] udevd[108]: starting eudev-3.2.9 <6>[ 18.561005] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <4>[ 18.609504] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 18.625863] wm8904 2-001a: revision A <6>[ 18.629922] fsl_ddr_edac acquired irq 108 for MC <4>[ 18.635761] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 18.643549] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.659478] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 18.661999] NET: Registered PF_INET6 protocol family <6>[ 18.671410] fsl_ddr_edac MC err registered <4>[ 18.680930] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 18.686624] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <6>[ 18.694928] Segment Routing with IPv6 <4>[ 18.708370] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 18.709786] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 18.715215] In-situ OAM (IOAM) with IPv6 <6>[ 18.725675] rtc-rv8803 0-0032: registered as rtc0 <4>[ 18.732381] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 18.738886] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 18.741747] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <3>[ 18.763472] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 18.776592] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 18.798019] input: buttons1 as /devices/platform/buttons1/input/input12 <6>[ 18.805504] CAN device driver interface <6>[ 18.841659] ftm-alarm 2800000.rtc: registered as rtc1 <6>[ 18.900294] caam 8000000.crypto: Entropy delay = 3200 <6>[ 18.906519] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 18.911714] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 18.920573] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 18.927572] usbcore: registered new device driver onboard-usb-dev <6>[ 18.928826] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 18.934691] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 18.952018] mali-dp f080000.display: Adding to iommu group 9 <6>[ 18.952860] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 18.969641] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <4>[ 18.982672] sysfs: cannot create duplicate filename '/devices/platform/sound/sai-tx-rx-wm8904-hifi' <4>[ 18.992306] CPU: 1 UID: 0 PID: 111 Comm: udevd Not tainted 6.12.0-rc6 #1 <4>[ 18.999300] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT) <4>[ 19.007855] Call trace: <4>[ 19.010566] dump_backtrace+0xec/0x108 <4>[ 19.014600] show_stack+0x18/0x24 <4>[ 19.018189] dump_stack_lvl+0x40/0x84 <4>[ 19.022125] dump_stack+0x18/0x24 <4>[ 19.025711] sysfs_create_dir_ns+0xe8/0x144 <4>[ 19.030173] kobject_add_internal+0x220/0x3cc <4>[ 19.034809] kobject_add+0x94/0x108 <4>[ 19.038570] device_add+0x148/0x448 <4>[ 19.042332] device_register+0x20/0x30 <4>[ 19.046355] snd_soc_add_pcm_runtimes+0x578/0xb40 <4>[ 19.051340] snd_soc_bind_card+0x3a8/0xd98 <4>[ 19.055713] snd_soc_register_card+0xf0/0x108 <4>[ 19.060347] devm_snd_soc_register_card+0x4c/0x90 <4>[ 19.065331] simple_probe+0x340/0x390 [snd_soc_simple_card] <4>[ 19.071193] platform_probe+0xa8/0xd0 <4>[ 19.075130] really_probe+0x128/0x2c8 <4>[ 19.079065] __driver_probe_device+0xa0/0x128 <4>[ 19.083704] driver_probe_device+0x3c/0x1f8 <4>[ 19.088161] __driver_attach+0xdc/0x1a4 <4>[ 19.092272] bus_for_each_dev+0xec/0x144 <4>[ 19.096471] driver_attach+0x24/0x30 <4>[ 19.100321] bus_add_driver+0x154/0x26c <4>[ 19.104431] driver_register+0x68/0x100 <4>[ 19.108539] __platform_driver_register+0x24/0x30 <4>[ 19.113521] init_module+0x20/0xffe8 [snd_soc_simple_card] <4>[ 19.119289] do_one_initcall+0xcc/0x240 <4>[ 19.123398] do_init_module+0x54/0x28c <4>[ 19.127421] load_module+0x1470/0x1714 <4>[ 19.131442] __arm64_sys_finit_module+0x264/0x300 <4>[ 19.136421] invoke_syscall+0x48/0xd0 <4>[ 19.140357] do_el0_svc+0x7c/0xa8 <4>[ 19.143942] el0_svc+0x34/0x7c <4>[ 19.147266] el0t_64_sync_handler+0x84/0xfc <4>[ 19.151723] el0t_64_sync+0x190/0x194 <3>[ 19.161111] kobject: kobject_add_internal failed for sai-tx-rx-wm8904-hifi with -EEXIST, don't try to register things with the same name in the same directory. <3>[ 19.176079] asoc-simple-card sound: probe with driver asoc-simple-card failed with error -12 <6>[ 19.176872] caam_jr 8010000.jr: Adding to iommu group 10 <6>[ 19.209862] caam algorithms registered in /proc/crypto <6>[ 19.215368] caam 8000000.crypto: registering rng-caam <6>[ 19.221018] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.228273] caam_jr 8020000.jr: Adding to iommu group 11 <6>[ 19.238014] caam_jr 8030000.jr: Adding to iommu group 12 <6>[ 19.246110] caam_jr 8040000.jr: Adding to iommu group 13 done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-512098/environment . /lava-512098/environment / # /lava-512098/bin/lava-test-runner /lava-512098/0 /lava-512098/bin/lava-test-runner /lava-512098/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 19.859115] d /lava-512098/0/tests/0_dmesg + cat uuid + UUID=512098_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.880874] <8>[ 19.902957] <8>[ 19.927126] + set +x <8>[ 19.936553] / #