Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot 2019.04-linux4sam_6.2-icp (Jul 22 2022 - 14:29:27 +0000), Build: BETA-1.03-20220722142927 CPU: SAMA7 Reset Source : SYSRESET Watchdog enabled DRAM: 1 GiB MMC: emmc@e0830000: 0 Loading Environment from SPI Flash... SF: Detected sst26vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial VPD: BOARD_SERIAL K1FT80003, MAC 00:A0:A5:5C:6D:96 Net: eth0: port0 [PRIME], eth1: port1, eth2: port2, eth3: port3, eth4: port4, eth5: port5, eth6: port6, eth7: port7 POST memory PASSED POST env PASSED POST vpd PASSED => setenv autoload no setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp dhcp port4 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.109 (756 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x62000000 510860/tftp-deploy-0xj7lu9s/kernel/zImage tftp 0x62000000 510860/tftp-deploy-0xj7lu9s/kernel/zImage tftp 0x62000000 510860/tftp-deploy-0xj7lu9s/kernel/zImage port4 Waiting for PHY auto negotiation to complete...... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.109; sending through gateway 172.16.0.254 Filename '510860/tftp-deploy-0xj7lu9s/kernel/zImage'. Load address: 0x62000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################## 1.7 MiB/s done Bytes transferred = 10994176 (a7c200 hex) => tftp 0x68080000 510860/tftp-deploy-0xj7lu9s/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 510860/tftp-deploy-0xj7lu9s/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 510860/tftp-deploy-0xj7lu9s/ramdisk/ramdisk.cpio.gz.uboot port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.109; sending through gateway 172.16.0.254 Filename '510860/tftp-deploy-0xj7lu9s/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################# 2.2 MiB/s done Bytes transferred = 17822318 (10ff26e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x68000000 510860/tftp-deploy-0xj7lu9s/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb tftp 0x68000000 510860/tftp-deploy-0xj7lu9s/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb tftp 0x68000000 510860/tftp-deploy-0xj7lu9s/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.109; sending through gateway 172.16.0.254 Filename '510860/tftp-deploy-0xj7lu9s/dtb/lan966x-kontron-kswitch-d10-mmt-8g.dtb'. Load address: 0x68000000 Loading: *# 2 KiB/s done Bytes transferred = 13227 (33ab hex) => setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 ## Loading init Ramdisk from Legacy Image at 68080000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17822254 Bytes = 17 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Using Device Tree in place at 68000000, end 680063aa Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j361255-arm-gcc-12-multi-v7-defconfig-config-smp-n-7fqtl) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 Mon Nov 4 02:34:19 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Kontron KSwitch D10 MMT 8G [ 0.000000] earlycon: atmel_serial0 at MMIO 0xe0040200 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000008fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000090000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 37.50MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x8a60dd6a9, max_idle_ns: 440795204056 ns <6>[ 0.000002] sched_clock: 56 bits at 38MHz, resolution 26ns, wraps every 2199023255540ns <6>[ 0.008279] Switching to timer-based delay loop, resolution 26ns <6>[ 0.017400] Console: colour dummy device 80x30 <6>[ 0.022081] Calibrating delay loop (skipped), value calculated using timer frequency.. 75.00 BogoMIPS (lpj=375000) <6>[ 0.032674] CPU: Testing write buffer coherency: ok <6>[ 0.037784] pid_max: default: 32768 minimum: 301 <6>[ 0.042903] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.050372] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.061004] Setting up static identity map for 0x60300000 - 0x603000ac <6>[ 0.070047] EFI services will not be available. <6>[ 0.074815] Memory: 926968K/1048576K available (15360K kernel code, 2542K rwdata, 6716K rodata, 2048K init, 413K bss, 54044K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.091213] devtmpfs: initialized <6>[ 0.099670] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.107906] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.117954] futex hash table entries: 256 (order: -1, 3072 bytes, linear) <6>[ 0.128772] pinctrl core: initialized pinctrl subsystem <6>[ 0.136953] DMI not present or invalid. <6>[ 0.142760] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.151588] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.161701] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.161755] cpuidle: using governor menu <6>[ 0.172612] No ATAGs? <6>[ 0.175027] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.183319] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.192419] Serial: AMBA PL011 UART driver <6>[ 0.211070] platform e2004064.pinctrl: Fixed dependency cycle(s) with /soc/pinctrl@e2004064/phy-int-pins <6>[ 0.246428] at_xdmac e0068000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.257217] iommu: Default domain type: Translated <6>[ 0.262156] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.269907] SCSI subsystem initialized <6>[ 0.309472] usbcore: registered new interface driver usbfs <6>[ 0.315172] usbcore: registered new interface driver hub <6>[ 0.320774] usbcore: registered new device driver usb <6>[ 0.327410] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.332557] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.341963] PTP clock support registered <6>[ 0.346314] EDAC MC: Ver: 3.0.0 <6>[ 0.387293] scmi_core: SCMI protocol bus registered <6>[ 0.410732] vgaarb: loaded <6>[ 0.414246] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.477338] NET: Registered PF_INET protocol family <6>[ 0.482790] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.493953] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.502643] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.510613] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.518726] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.526225] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.532884] UDP hash table entries: 512 (order: 1, 8192 bytes, linear) <6>[ 0.539626] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear) <6>[ 0.547081] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.626283] RPC: Registered named UNIX socket transport module. <6>[ 0.632364] RPC: Registered udp transport module. <6>[ 0.637374] RPC: Registered tcp transport module. <6>[ 0.642303] RPC: Registered tcp-with-tls transport module. <6>[ 0.648072] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.654806] PCI: CLS 0 bytes, default 64 <5>[ 0.660648] Initialise system trusted keyrings <6>[ 0.680865] Trying to unpack rootfs image as initramfs... <6>[ 0.739329] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.746642] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.784863] NFS: Registering the id_resolver key type <5>[ 0.790191] Key type id_resolver registered <5>[ 0.794588] Key type id_legacy registered <6>[ 0.798863] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.805807] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.875246] Key type asymmetric registered <5>[ 0.879512] Asymmetric key parser 'x509' registered <6>[ 0.884874] bounce: pool size: 64 pages <6>[ 0.888939] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.896586] io scheduler mq-deadline registered <6>[ 0.901308] io scheduler kyber registered <6>[ 0.905644] io scheduler bfq registered <6>[ 1.014503] pinctrl-ocelot e2004064.pinctrl: driver registered <6>[ 1.029046] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.427531] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.450638] msm_serial: driver initialized <6>[ 1.455437] SuperH (H)SCI(F) driver initialized <6>[ 1.460366] STMicroelectronics ASC driver initialized <6>[ 1.465768] STM32 USART driver initialized <5>[ 1.543146] random: crng init done <6>[ 1.617813] brd: module loaded <6>[ 1.638514] loop: module loaded <6>[ 1.648030] atmel_usart_serial atmel_usart_serial.0.auto: Using FIFO (32 data) <6>[ 1.656296] atmel_usart_serial.0.auto: ttyAT0 at MMIO 0xe0040200 (irq = 24, base_baud = 12500000) is a ATMEL_SERIAL <6>[ 1.667015] printk: legacy console [ttyAT0] enabled <6>[ 1.667015] printk: legacy console [ttyAT0] enabled <6>[ 1.677225] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 1.677225] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 1.844780] CAN device driver interface <6>[ 1.850055] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.857205] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.862398] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.868715] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.874355] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.885115] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.890990] usbcore: registered new interface driver pegasus <6>[ 1.896975] usbcore: registered new interface driver asix <6>[ 1.902651] usbcore: registered new interface driver ax88179_178a <6>[ 1.909046] usbcore: registered new interface driver cdc_ether <6>[ 1.915184] usbcore: registered new interface driver smsc75xx <6>[ 1.921197] usbcore: registered new interface driver smsc95xx <6>[ 1.927235] usbcore: registered new interface driver net1080 <6>[ 1.933159] usbcore: registered new interface driver cdc_subset <6>[ 1.939369] usbcore: registered new interface driver zaurus <6>[ 1.945220] usbcore: registered new interface driver cdc_ncm <6>[ 1.956112] usbcore: registered new interface driver usb-storage <6>[ 1.968874] i2c_dev: i2c /dev entries driver <6>[ 2.303129] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.309670] sdhci: Copyright(c) Pierre Ossman <6>[ 2.316572] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.324930] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.336136] usbcore: registered new interface driver usbhid <6>[ 2.341955] usbhid: USB HID core driver <6>[ 2.354658] NET: Registered PF_INET6 protocol family <6>[ 2.506867] Segment Routing with IPv6 <6>[ 2.510843] In-situ OAM (IOAM) with IPv6 <6>[ 2.515156] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.522296] NET: Registered PF_PACKET protocol family <6>[ 2.527641] can: controller area network core <6>[ 2.532279] NET: Registered PF_CAN protocol family <6>[ 2.537317] can: raw protocol <6>[ 2.540526] can: broadcast manager protocol <6>[ 2.545003] can: netlink gateway - max_hops=1 <5>[ 2.550315] Key type dns_resolver registered <6>[ 2.555251] ThumbEE CPU extension supported. <5>[ 2.559758] Registering SWP/SWPB emulation handler <5>[ 2.735698] Loading compiled-in X.509 certificates <6>[ 5.264588] Freeing initrd memory: 17408K <6>[ 15.274421] clk: Disabling unused clocks <6>[ 15.278605] PM: genpd: Disabling unused power domains <6>[ 15.289644] Freeing unused kernel image (initmem) memory: 2048K <6>[ 15.293632] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.522202] udevd[66]: starting version 3.2.9 <27>[ 15.539928] udevd[66]: specified user 'tss' unknown <27>[ 15.542689] udevd[66]: specified group 'tss' unknown <30>[ 15.552271] udevd[67]: starting eudev-3.2.9 <6>[ 17.354717] atmel_aes e004c000.crypto: version: 0x702 <6>[ 17.381752] atmel_sha e006c000.crypto: version: 0x700 <6>[ 17.408043] MAC addr was not set, use random MAC <6>[ 17.436567] atmel_aes e004c000.crypto: Atmel AES - Using dma0chan0, dma0chan1 for DMA transfers <6>[ 17.462922] atmel_sha e006c000.crypto: using dma0chan2 for DMA transfers <6>[ 17.467330] atmel_sha e006c000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 17.512006] atmel_spi e0064400.spi: Using dma0chan3 (tx) and dma0chan4 (rx) for DMA transfers <6>[ 17.518221] atmel_spi e0064400.spi: Using FIFO (32 data) <6>[ 17.710509] atmel_spi e0064400.spi: Atmel SPI Controller version 0x401 at 0xe0064400 (irq 32) <6>[ 17.745364] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 17.816551] MAC addr was not set, use random MAC done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # # / # export SHELL=/bin/sh export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-510860/environment . /lava-510860/environment . /lava-510860/environment / # /lava-510860/bin/lava-test-runner /lava-510860/0 /lava-510860/bin/lava-test-runner /lava-510860/0 /lava-510860/bin/lava-test-runner /lava-510860/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-510860/0/tests/0_dmesg + cat uuid + UUID=510860_1.5.2.4.1 + set +x <8>[ 21.616743] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 21.683030] <8>[ 21.741970] <8>[ 21.801031] + set +x <8>[ 21.809422] / #